After the installation of 8500 a909n printer works wireless for a few months and then quit?

Similar Questions

• My internet connection is lost at home after a few minutes. I re - turn on the wifi disabled, ten and it works again for a few minutes and then repeats. It works fine everywhere else?

  Relatively new MacBook OSX El Cap 11.4

  My internet connection is lost at home after a few minutes. I stop the wifi, then turn it back on and it works again for a few minutes and then repeats. It works fine everywhere else?

  Please see recommended settings of WiFi routers and access Apple points.

  Despite these recommendations, some routers will work better with the latest Mac models if you turn the radio 2.4 GHz mode in settings and only use the 5 GHz. Note, however, that very old devices Apple and some third-party devices can then not connect at all.

  Some third party routers have advanced that you may need to change the settings:

  The encryption algorithm must be AES.

  The group key interval must be 3200.

  I can't give you specific instructions on how to change these settings, because all routers are different. Refer to the documentation for the provider.

• at the opening of some programs it will run for a few seconds and then show a blue or white screen screen or a screen scratched

  occurs when you have a few seconds in the program sometimes it happens on the web

  Hello

  1 did you change on your computer before this problem?

  2. what programs you're talking about?

  3. you receive an error message?

  4. what anti-virus software is running on your computer?

  You can follow the suggestions and check out them.

  Method 1

  You can run the fix of the article.

  Difficulty of Windows system performance slow computer problems

  http://support.Microsoft.com/mats/slow_windows_performance/en-us

  Method 2

  You can follow the procedure in the article.

  Slow PC? Optimize your computer for peak performance

  http://www.Microsoft.com/athome/Setup/optimize.aspx#fBid=c4ypPwpWrR1

  Note: All by performing the check disk on the hard drive if bad sectors are found then check disk will attempt to repair this area, all available data on this sector can be lost.

   

  Method 3

  You can check if the problem exists in a clean boot state to see if a third-party service is causing the issue.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  a. click Startand then click run.

  b. type msconfigand click OK.
  The System Configuration utility dialog box appears.

  c. click on the general tab, click Normal Startup - load all device drivers and servicesand then click OK.

  d. When you are prompted, click restart to restart the computer.

  Method 4

  You can disable temporary of your security software.

  a. log in as an administrator on the Windows XP computer.

  b. in the notification area in the taskbar, right-click on the icon of the antivirus program.

  c. click on disable. Antivirus protection is now disabled.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

• Hi, I am Ganesh, I tried to installed the application using creative cloud. But seems it's taking too long to install the application and it is hit. After the installation of 42%. Still, I tried to restart my computer and re-install the application. But i

  Hi, I am Ganesh, I tried to installed the application using creative cloud. But seems it's taking too long to install the application and it is hit. After the installation of 42%. Still, I tried to restart my computer and re-install the application. But it is keep taking so long time and struck at the end of the installation of 42%.

  If the installation process is stalled at 42 percent with no possibility of error, there is a problem with the zipped file to Extraction of downloaded in the Temp folder.

  As a fundamental step. Leave the creative Cloud desktop application.

  Delete the contents of the Temp folder:

  Optional: it will be ideal to install software like Winrar, WinZip or 7-zip,., etc.

  Please press Windows + R and you will get a command window run, get hit and type %temp%.

  Delete all the content inside the temp folder.

  
  

  
  Then try again to install application InDesign CC again.

  Just in case, if you are still having the same issue.

  Creative application cloud thus released, do not close it.

  Open the Temp folder, then search for the CC InDesign installation file and copy it to the desktop computer.

  Then leave Creative Cloud application and try to install.

• After that turn the power off for a few days and then back on... all my desktop ICONS was reorganized.

  After that turn the power off for a few days and then back on... all my desktop ICONS changed. I placed the worms where I want that they and computer restarted and they get rearranged again. Help, please.

  Hello Kenneth Pincus,

  You can create a new profile on the computer and if the desktop icons stay on their position. If this is not the case, the other profile is corrupt. To create a new user profile, you can see the article mentioned below for the procedure.

  How to create and configure user accounts in Windows XP

  http://support.Microsoft.com/kb/279783

   

  How to copy data from a corrupted to a new profile in Windows XP user profile

  http://support.Microsoft.com/kb/811151

  Let us know the results.

• Illustrator: 'nodes' on the corners of the images or shapes are red instead of open boxes & Icannot resize these elements by dragging the nodes.  I just got the latest version of Illustrator and it worked fine for a few weeks and now I can't do it aga

  Illustrator: 'nodes' on the corners of the images or shapes are red instead of open boxes & Icannot resize these elements by dragging the nodes.  I just got the latest version of Illustrator and it worked fine for a few weeks and now I can't do it again on the right.

  View > Show bounding solve?

• Hold the head of reading for a few seconds, and then go

  Hello world

  How to hold the head of a frame for a few seconds and then have the read head continue to play? I don't know how to do this in AS3.

  Thank you

  Rafa.

  These things indicate (to me), you have done a good thing and studied the help files for how to use the function, although you may have considered in the section of AS2.  In addition, get rid of them.  They are specific to some example were the help files.  The bit in quotes is an argument that would be sent to the function, which receives it as arg1.  I can only imagine that one of the mistakes was to not to declare the type of argument, that requires AS3, but like I said, just get rid of them altogether.  For AS3, things are slightly different, the return value is a uint

  Stop();
  var setHold:uint = setTimeout (holdPlayhead, 2000);

  function holdPlayhead () {}

  gotoAndPlay (26);
  }

• Vista crashes after using it for a few minutes and then does not start (after a few hours - it starts and again the same problem)

  I'll have this weird problem and did not find the problem. Suddenly my laptop (Lenovo Y710 - 4 GB RAM - Windows Vista Home Premium 32 bit) crashes after a few minutes of activity, Vista freezes. CTRL + Alt + Delete does not work. If I force close to the bottom and then try to restart, it do display anything. I tried to start in safe mode, but after pressing f8 and it only beeps and still doest appear anyting on screen you. If I try to start the laptop after a few hours it starts again and minutes it freezes again. I noticed this problem for the first time when using RDP to my desktop, but it wasn't the first time I've done RDP. I have not installed new hardware or drivers. Am not able to nail the question, would appreciate any help.

  Thank you.

  This is no doubt hardware failure. The laptop could be overheating and/or other components could be involved. Contact Lenovo technical support or take to a competent local computer Tech do not use a type of BigComputerStore/GeekSquad of the place.

  If you have a pretty good level of computer skills, you can test some components yourself although it is more difficult to make accurate material on a laptop computer troubleshooting.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot
  MS - MVP - Elephant Boy computers - don't panic!

• Satellite L350D works for a few minutes and then stop completely

  Hi all!

  I'm having a weird problem with my laptop Satellite L350D-216
  I have used for a long time in a row and is starting to show some strange vertical lines on the screen and the kind of activity let go and then it went completely black
  Since then if I disconnect and leave it for a few hours switches normally and work for 5/10 minutes and turns black again.
  It happens after I worked on it for about 20 hours straight or Yes (can be linked)

  What I tried:
  -Turn on with battery only
  -Turn on only with the ca
  -Remove all and to hold off key for 1 min and then try again the two above

  When it comes on everything seems to work 100% without problem but don't lasts no more than 10 minutes as I said

  Any ideas?
  Thanks in advance

  I can't say for sure, but the problem may be material high temperature. Satellite L350D is not the latest model cell phone and if you use enough difficult I guess laptop is full of dust and cannot be properly cooled.

  Maybe the laptop needs to be cleaned.
  > When it lights up everything seems to be working 100% without problem, but does not last more than 10 minutes as I said
  One more thing: do the quick test. Start your laptop and enter the BIOS settings. Leave it for a while and check if the same thing will happen again.

  Please post comments.

• PC hangs for a few seconds, and then return as normal and fast as always, no reports of any problems in the operating system.

  Hello world

  I have a Vista Ultimate SP2 system and all updates, my hardware is an AMD Athlon 64 x 2 3.2 Ghz with a RAID 0 (2 discs), 4 GB of RAM, video memory shared up to 1 GB, Asus M2A-VM Motherboard.

  My problem is that sometimes when you work with any my computer shutdown application package to meet any keyboard or mouse control for 2-3 seconds and suddenly come back with tasks in the queue and fast as usual.

  I've updated my Chipset and RAID drivers.

  I uninstalled ASUS ACPI Center who could be one of the causes of this problem, rename the executable to Center asus acpi.

  I ran TuneUp Disk Doctor to verify my RAID and fix problems

  I update and updated my Antivirus ESET Smart Security in order to improve the performance of the process EKRN who sometimes take a large part of the time CPU.

  Can someone advice me how track and what tools to use to run a diagnosis of systemd and check if my problem is with the hardware or the operating system?

  Kind regards.

  JUOX.

  Run process monitor. Stop the trace when your problem occurs. Look through the timestamps of the gaps.

  See this for an example of the use of Process Monitor to diagnose a deadlock:

  http://blogs.technet.com/markrussinovich/archive/2010/01/13/3305263.aspx

• When I log on my monitor only stays on for a few seconds and then goes black. need to turn the screen off and on several times before it lights.

  fact it for about a week now.  have ran antivirus scans and asked a lot of people who were not able to help me at the moment.

  It looks like a hardware problem.  Your monitor, cable or even the video card in your computer goes wrong.  My bet is on the screen.  Try to swap the monitor with another computer and see if the problem follows the monitor or the computer.

  HTH,
  JW

• Re: Satellite A660 - 11 M - Random freezing after the installation of recovery

  Hello

  I recently bought an A660 - 11 m, which I was happy for a few months and then it started to crash/freeze randomly in windows. I'd do something and then it just would freeze indefinitely, requiring a second 5 press the power button to turn it off manually. The fan and hard drives would continue to work if he did something, or they wouldn't be if I was not doing something at the time (this has happened four times). After that it's the only thing to do would be to reinstall the entire operating system by using the manufacturers recovery disk. The computer will then work fine for a few days or a few weeks (never more than 2 weeks) and it would be demanding full gel reinstall again. I had reinstall my programs every time but I stopped on the last 2 times and it made no difference.

  After that the computer crashed it would then refuse to boot into windows. It would be still stuck just at the moment where the sign of windows appears. I would like to know that he had crashed as the 4 colored dots appear. The computer would simply wants at this point, continually getting stuck there after the reboot of several manual. Once and only once it booted into windows on its own, but it took almost 30 minutes and the computer is very slow and unresponsive. The computer will sometimes start in safe mode, but it varies. I tried Startup Repair tool and all stages of system restore, but none of these work.

  I got to use Acronis true image10 and creating an image of the system which can then replace the whole computer in all 25mins. This saves me time, rather than wait 2 hours or whatever it is to reinstall the toshiba, but becomes quite ridiculous to have to keep re install every two weeks.

  I also tried to buy a stand-alone copy of windows 7 (while recording an image of the partition of toshiba in the case where I need) I think it might be due to all toshiba programs and other bits and pieces that are installed on the computer - it makes much faster startup, but the computer still crashes the same after awhile.

  I am sure its some ware conflicts or driver pretty hard, but I don't know what.

  Any help please!

  Rob

  Hi Rob,

  I m also do not know what exactly is the problem and I believe that no one here can say that just because it s just a user to user forum.

  Fact is that if you have already tried restore factory Toshiba recovery disc multiple times, it s not a software or driver issue because it s an image pre-tested by Toshiba.

  I guess it must be a hardware malfunction and therefore, you should contact a service provider for help. Guys can check your laptop and if it of under warranty, the repair is free.

  You can find a list of aspic here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• Satellite 1800-814 does not start after the installation of the software

  Hello
  If I pass on my old Satellite S1800-814, it seems to start correctly: it shows the symbol of "Toshiba", then "Windows XP loading", then the screen goes completely blank, followed by a black screen showing the cursor that I am able to move. The hard drive continues to hum as usual for a few seconds, but then begins to repeat a series of clicking noises, somewhat like a disk that is stuck. The boot process is not still engaged.

  Here's the context: I installed my (old) version of Avid Xpress Pro editing software on my Satellite 1800-814. I managed to install a newer version, even if it does not function effectively, where my attempt to install an older version more closely adapted to the processing speed and the size of the RAM 1800-814. I got the usual warning at the end of the installation program of Avid saying that Windows can be affected if I let the installation ends in letting the computer on. But I pressed the option "continue anyway" (as I've done it before without negative effects). The computer off, but he came in as described above. Please tell me what I broke. Can I ever solve this?

  Thanks for your help.

  Hello

  Try to start your computer in safe MODE and try to remove preinstalled software. Please report the results.

• When I connect my laptop L300D to my LCD tv using VGA to VGA it works fine for a few minutes then the screens n that the laptop and TV started blinking on and outside. Can someone advise please.

  When I connect my Toshiba L300D laptop to my Samsung 40 inch lcd tv using vga to vga connection it works fine for a few minutes. Then the screens on the laptop and the TV start to turn on and turn off, also jumps around cursor. Can someone tell me what is the problem and how to correct.

  Hello

  Try changing the VGA cables and check if it helps.

  If the problem persists, then I suggest you to update the firmware.

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• HP Photosmart C5280 All in One printer works is not after the installation of updates

  OP: Problems with my HP Pavilion connect with my HP Photosmart C5280 All in one. Allows to work properly and after running the update something happened.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello iwasbetterbutgotoverit,

  1. do you have an update of the hardware installed on your computer?

  2. what exactly happens when you try to print from the printer?

  I suggest that you try the methods below to solve the problem.

  Method 1:

  I suggest that you run the printer troubleshooter. This automatically diagnose and fix printing problems, installation of a printer, connecting to a network printer and other related errors:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Method 2:

  As it was working fine before installing the update, I suggest that you do a system restore on your computer.
  To restore the operating system to an earlier point in time, follow these steps:

  a. Click Start, type system restore in the search box and then in the list click on the system restore program.

  b. If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  (c) in the System Restore dialog box, click on choose a different restore point and then click Next.

  d. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  e. click Finish.

  You can visit the link to the KB Article for reference:

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  You can use the System Restore tool to undo the system restore if it does not help.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.