After the upgrade to USB 3 Hub Ethernet Sierra is no longer works

Similar Questions

• After the upgrade to Firefox 7, sites regularly take a very long time to load.

  Since the upgrade to Firefox 7, I knew an intermittent problem where, in the attempt to load of a site, the status bar says "Connecting"... "and sits there without charging anything for several minutes. This happens usually after several minutes of normal use. Meanwhile, Firefox cannot connect to any site. He is also unable to check the updates. There is no error message; simply, it displays the icon of the "little wheel" and does not provide any additional comments.

  Close the tab where the problem occurred at the outset helps not, but completely close and restart Firefox made. However, the problem usually after several minutes of normal use after a reboot.

  No other application is affected. Internet Explorer, MSN Live Messenger, Thunderbird, and other applications of the network continue to operate normally while Firefox cannot load websites.

  I don't think that it is a firewall issue. The problem occurs even when all the firewall software - including the built-in Windows - Firewall has been disabled.

  In addition, if I let Firefox "spin" for several minutes, the problem suddenly clears up on its own, and the site I asked initially load normally. As with a reboot, when the problem is cleared up in this mode, generally occurs after a few minutes of normal use.

  Type of topic: config in the address bar (address) and press the Enter"" key. When you see a warning, click on I'll be careful, I promise! button.

  -> In the filter bar, type Network.http.Max - connections

  • Preference Network.http.Max - connections right click and choose Edit
  • Change the value to 30 or 48
  • Click OK

  -> Close the topic: config tab

  • Restart Firefox.

  Check and tell if its working.

• After the upgrade to Windows 10 Lightroom stops responding while I'm working

  In windows 7, I couldn't activate GPU?  In windows 10 I can.  When I tried Disabling GPU to see if that was the problem, Lightroom stops working when I click on the box.

  New to this spirit there is a section manually disable the graphics processor. Just give it a go. It worked for me and I no longer hand LR gel.

• After the upgrade to FireFox 30, we can access is no longer internal websites. He gives us 401 - non authorized: access denied due to credentials not valid.

  What is happening on our internal websites used to ask for a window to enter your credentials. This is not is no longer the case.

  It comes immediately gives us a

  401-Unauthorized: access is denied due to credentials not valid.
  You don't have permission to view this directory or page using the credentials you supplied.

  Hello, this is perhaps due to the deactivation of some insecure authentication protocols in firefox 30: https://www.mozilla.org/en-US/firefox/30.0/releasenotes/#whatsnew

  You can try to enter Subject: config in the address bar of firefox (confirmed the message information where it appears) and search for the preference named network.negotiate - auth.allow - insecurity-ntlm-v1. Double-click it and change its value to true.

• Laptop Compaq CQ58: LAN Ethernet does not work after the upgrade to windows 8.1

  After the upgrade of Windows 8 to 8.1, my Ethernet LAN is no longer in effect. Wireless LAN connectivity is OK. I run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I don't see a listed 8.1 for the LAN Ethernet driver.

  It seems that you encounter the same problem, I did when I ran the free preview of the W10. I had this error on the card reader.  I have no idea how to solve this problem.

  Is there is no ethernet controller needing drivers in Device Manager, then it is probably the realtek lan adapter that has the number 12 of the code, or it is part of the motherboard that controls the ethernet adapter.

  If you need Atheros bluetooth driver, then this is probably the one you need.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_127984_1

  Unfortunately, I won't be able to help you with question 12 code or ethernet.

  IMO, they are insoluble.

• Drivers for USB audio devices do not detect my Casio keybaord (piano) after the upgrade to Intel core i5

  I have windows XP with SP2.

  Device drivers audio USB is unable to detect my Casio keybaord (piano) after the upgrade to Intel core i5. Usually, when I connect my keyboard via USB, the drivers used to get automatically installed. But now he is unable to install the drivers and still shows the yellow "?" symbol. I tried everything but nothing seems to work. Someone please help. :-(

  If you update your motherboard, you must install the drivers available from your mobo site and not from winupdate

• Does not start after the upgrade to 1.5.

  Does not start after the upgrade to 1.5.  "EdgeAnimate.exe - not found entry Point? -Point procedure entry GetGestureInfo is not found in USER32.dll dynamic link library. »

  All ideas

  No problems in the past with edge since September 2012.

  =============

  Laptop HP Pavilion dv7-2185dx

  Dv7-2185dx product name

  #ABA product number NV023UA

  Microprocessor 2.00 Ghz Intel Centrino 2 Processor Intel Core 2 Quad Q9000 processor technology

  The microprocessor Cache L2 6 MB Cache memory

  6144 MB of memory

  Memory Max 8192MB

  Graphic ATI Mobility Radeon HD 4650 (M96)

  Video memory up to 2815 MB (1024 MB dedicated)

  500 GB (5400 RPM) hard drive

  Multimedia drive LightScribe SuperMulti 8 X DVD±R/RW with Support Double layer

  17.3 "diagonal HD + LED display high-definition HP BrightView Widescreen Display (1600 x 900)

  Fax/Modem high speed 56 k modem

  Network integrated 10/100/1000 Gigabit Ethernet LAN adapter

  Wireless Connectivity Intel WiFi Link 5100AGN

  The Altec Lansing SRS Premium Sound technology with subwoofer

  101 keyboard compatible with the keyboard keys full size numeric keypad with integrated

  Pointing device touch pad with On / Off button and dedicated vertical scroll up/down pad

  PC Card Slots 1 Slot ExpressCard/54 (also supports ExpressCard/34)

  External ports

  5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card

  4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA

  2 headphone

  1 microphone input

  HDMI

  1 VGA (15-pin)

  eSATA + USB 2.0

  1 RJ-11 (modem)

  1 RJ - 45 (LAN)

  expansion port for computer 1 cell 3

  1 IEEE 1394

  irewire (4 pin)

  1 consumer IR (remote receiver)

  Other devices HP Webcam with integrated digital microphone

  Dimensions 16.2 "(W) x 10.9" (D) x 1.37 "(min H) / 1.70" (maximum H)

  Weight lbs 7,74

  Housing for Kensington MicroSaver Security lock

  Turn on the password

  Accepts 3rd party locking safety devices

  Software

  Operating system:

  Genuine Windows Vista Home Premium 64-bit with Service Pack 1

  
  

  Hi, people.

  I was able to reproduce the problem here, so the good news is that you're not imagining things.  We are looking in the options right now for you guys, and I will contact you individually by private message to start again at the top.  This being said, please note that our techniques, Vista is an operating system that is not supported, and our team is not stable time on this platform.  We will do the best we can and we will keep you guys, update as to what status is.

  Thank you

  -Elaine

• Volume controls on the keyboard after the upgrade to Windows 8

  I have a Touchsmart 520-1070 with the mouse and keyboard without wire factory.  After the upgrade to WIndows 8, the volume controls no longer work.  I tried the Recovery Manager to reinstall the keyboard drivers, but there is no driver keyboard under hardware drivers.

  In the following device manager are listed under keyboards:

  HID keyboard device

  Keyboard 109 MCIR Microsoft eHome

  Keyboard MCIR Microsoft eHome

  Microsoft eHome key remove control Keayboard

  PS/2 standard keyboard

  Any report that they are installed and are working correctly and that the drivers are up to date.

  Has anyone else seen or solved this problem with a Touchsmart computer?

  The instructions below were provided by HP support.  This has restored the function on the keyboard volume controls.  The referenced below drivers are drivers IDT high definition Audio Device.  I am not sure that it was necessary to reinstall the audio drivers.  It can only had to remove the USB dongle and back to restore the functionality of the button.  Note: the USB dongle is located behind the VESA Panel to the back of the PC.  No tools are required and the dongle can be removed and replaced without shutting down the PC.  VESA panel removal requires a bit of a steady hand, pulling the lip which is close to the connections on the rear panel.

  Instructions received from HP:

  Please go to the following link and check the "return of the system", article #7 is the USB dongle:

  http://support.HP.com/us-en/document/c03026390

  After you have reinstalled the receiver, please download and install the following driver:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-110499-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

  Then install the following update:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-112060-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

• HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

  Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

  Hi @Ron9871,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.

  Please restart the router, the printer and the computer in this sequence.

  If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  You can try to change your WSD printer port by a Standard TCP/IP port.

  To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

   

• 10 Windows compatible printers: printer problems after the upgrade to Windows 10

  If you're wondering what HP printers are compatible with Windows 10, see this HP support doc: Windows 10 compatible printers.

  If you re having a problem with your HP printer after the upgrade of your Windows 10 PC, printer problems after upgrade to Windows 10 could solve your problem. He treats all kinds of questions such as:

  • Cannot print after upgrading
  • Cannot parse after upgrade
  • Printer software installation & screen opens instead of HP printer Assistant
  • "HP solutions Center can not run" or "Scan is busy or in use" error with a network connected printer
  • Multiple display of printer in the HP printer Assistant names
  • Can not scan or fax with HP Solution Center after that disabling HP programs to improve performance
  • "Access denied" error change HP Solution Center print settings
  • Cannot print with a pilot integrated Windows (Africa, Asia Pacific, Europe and Middle East only)
  • Fax device are not not in the devices and printers connected to a USB printer
  • HP Printer Wizard does not open with a USB connected printer
  • HP Smart printing does not open in Internet Explorer
  • "Error-2081883401' poster during the uninstall of the printer driver.

  In the compatibility Windows 10 doc, follow these steps to quickly locate your printer:

  Click and scroll down to the section for your printer, then hold down the CTRL and F keys. When appears in the search box, type the number of printer model to automatically find your printer. TIP: find the numberof the printer. For example, if you have a HP Officejet Pro 8600 Premium e-all-in-one printer, open the Officejet section and search for "8600" instead of "Officejet 8600.

• Cannot connect to internet after a reboot before you uninstall and then reinstall the network card. (After the upgrade to Windows 7 from Vista)

  This problem started immediately after the upgrade to Windows 7 Ultimate (32 bit) to Windows Vista Ultimate (32 bit).  Again, I want to remind that I never had this problem before installing Windows 7.

  -After a reboot, I am presented with the impossible to connect the network indicator (yellow triangle with!) in the task bar.  (It was how I was welcomed after the installation of Windows 7 is said by the way).

  -The only way I found to regain connectivity is to uninstall and reinstall the network via the device manager card, date at which the computer always successfully connects and remains connected until the next reboot.

  Network card: Realtek RTL8168C (P) / 811C (P) Family PCI - E Gigabit Ethernet NIC (NDIS 6.20)

  Driver provider: Microsoft
  Driver date: 14/05/2009
  Driver version: 7.2.1127.2008
  Digital signer: Microsoft Windows

  Thus, we have solved the problem! There are two possibilities of your problems:
  1 company Adobe uses the Bonjour service , this service should be disabled.
  Computer > Manage > Services and Applications > Services => find the bonjour service (sometimes stated as long numbers), stop service and if the Disabled value. It works!

  2. If it is not signed as Bonjour service. Try to disable the service:
  Shutdown mDNSResponder .exe (he is represented by # Id_String1.6844F930_1628_4223_B5CC_5BB94B879762 #).

  It is installed with Adobe software. If you upgrade the Vista, it will generally many users problem!

• is more able to stream video from some sites after the upgrade to Safari 10

  

  After the upgrade to 10 Safari, I can no longer stream from a certain website. Instead of playing the video stream, I'm prompted to save "player.swf" as shown above.  This problem occurs on el Capitan, and it happens on the Sierra, and it all started when I updated Safari 9.x to 10.0

  Open Safari preferences / Security tab and check the box allow Plug-ins.

  Very soon of Flash player and the plugin will be obsolete and this web page needs to change its code to HTML5.

• Cannot connect to more than one mail account after the upgrade to Sierra

  I have several provided ISP e-mail accounts that work successfully for a long time on elCapitan.  After the upgrade to Sierra this afternoon cannot connect all accounts and I asks me to enter the password.  Why isn't Sierra pick up the passwords of my trousseau?

  Oddly enough, my Hotmail account seems to be ok.

  How can I fix this without having to re - enter all passwords?

  As a result of the foregoing, I found that my connection Keyring contains entries for all of my email accounts.  However, these dates are back in July 2011.

  After an episode of lost or stolen iphone, I had to update all of my passwords by e-mail in February this year (2016).

  Search in my keychain, I found dated entries for my email accounts in iCloud Keychain section.  I don't think that I never activated iCloud for my email.

  How the entires of e-mail account eventually sub iCloud and why the old entries from email account not updated?

• Major Outlook and timing of the problems after the upgrade of the El Capitan

  On the advice of the Apple support (phone call) I recently upgraded from Yosemite to El Capitan 10.11.6.

  I have many problems. The two largest are (1) stands (2016) Outlook and frequently "must be closed; (2) calendars quickly goes to "not responding" after the launch and shows multiple entries for a single event. Example: I have a class to repeat each week (when I was in Yosemite). Before the upgrade, he showed the event once a week. After the upgrade, it it shows 13452 times the same day. I followed the advice on these topics, but nothing has worked. Similarly the calendars on my iPhone5 freezes as well.

  Hello Steve,.

  Thank you for using communities Support from Apple. I have a problem with your MacBook Air use after update is not what you expect. Based on what you said, it seems you can experience some software related issues, and here's how I recommend refine you and resolve these issues:

  1. first of all, try to run a quick with the disk utility tool test, as this can correct simple problems that you encounter. Then restart normally and retest your problems.

  Disk utility (El Capitan): a disc repair

  2. use Mode without fail to start up your Mac so that it performs certain checks, remove files from the system cache, check your startup disk and trying to fix problems if necessary directory. Test mode safe questions, then restart normally and test again.

  Try safe mode if your Mac does not end commissioning
  Graphics performance limited in recovery of OS X or in safe mode

  3. you can find out if unexpected behavior is related to the user file or a parameter in trying to reproduce the problem to a different user account. This process includes creating a new user account, connect to it and test for the issue.

  How to test a question in another account on your Mac.

  See you soon!

• I wonder if I can pass my carrier unlocked iphone 4 iOS to iOS 7 8? or it will lock again after the upgrade?

  I wonder if I can pass my carrier unlocked iphone 4 iOS to iOS 7 8? or it will lock again after the upgrade?

  1 n ° iPhone 4S can only be directly updated to 9.3.3.

  2. update of the iOS on an iPhone that was originally sold as unlocked or is released by the carrier won't it relock.

  (143770)