After you have installed the free updates for Vista Home Premium 64 bit, Windows will not start

After that I installed the free updates to service pack 1, the system goes through 2 of the 3 steps, while it recharges, then the system does not boot?  To get the computer to work again, I need to run the repairer of Windows, which allows you to restore the system to an earlier point?  Does anyone have an idea how to fix this?

Do your system restore, then:

Click Start > right click on computer > properties > Windows updates down the lower left corner > updates installed in the lower left corner in the next window

> then click the one that you don't want > uninstall will appear at the top > uninstall it.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

In addition, on the page where you clicked "Installed updates", click on change settings at the top left corner it

> Change update settings in the next page of AutoUpdate to "check for updates but let me choose etc" > OK ".

When you take a look at pending updates, you can either download/install them one at the time, namely the update causing you problems.

> or if you do not need an individual > right-click on > UAC prompt > hide it

See you soon.

Mick Murphy - Microsoft partner

Tags: Windows

Similar Questions

  • My computer installs the automatic updates for Vista Home Premium, but fails to set them up.

    original title: Microsoft updates

    My computer installs the automatic updates for Vista Home Premium, but fails to set them up. I'll through in circles, trying to figure out what the problem is. Everything was fine until a week ago. Help please

    Thanks for trying to help. It was too complicated for me to fix, so to get help in. happy to say now, all right.

  • HP 8600 printer range is found on the network after you have installed the Dymo printer for processing of credit cards

    HP 8600 printer range is found on the network after you have installed the Dymo 450 Turbo printer for processing of credit cards

    Hello Christina,

    1. What is the IP (Internet Protocol) address, the subnet and default gateway of the printer?

    2 have you tried to Ping to the IP address of the printer?

    Reset the printer can help get the problem solved.

    Perform the steps mentioned below to get the address of IP(Internet Protocol), subnet address, and default gateway.

    a: Type CMD in the search box start and press ENTER.

    b: now, type Ipconfig/all and press ENTER.

    Proceed as for Ping to the IP address of the printer.

    a: Type CMD in the search box start and press ENTER.

    b: type PING (IP address of the printer) , and then press ENTER.

    Reset the printing system:
    a: Go to System Preferences > Print & Fax
    b: Right (or control), click inside the box that lists your printers and select Reset Printing System.

    WARNING- This will remove ALL your printers!
    c: Select the sign more to add a printer. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

    Click on the link mentioned below as reference.

    http://Windows.Microsoft.com/en-in/Windows7/install-a-printer-on-a-home-network

    Note: "Check the title that reads" set up a network printer "

    Answer please if you have any questions.

  • After you have installed the latest updates it freezes and blue screens or?

    I have installed the latest updates and it did not even to the part where he set up after a reboot.  Now I'm stuck in safe mode and no alternative.  Updates are not listed in the list of installed updates and I tried to do a repair of the system from the installation cd and I'm tempted to do a restore system since the day before two weeks before updates.  Nothing works.  Any suggestions will help!  I'd hate to reinstall because I have no backup support.

    Update: the event log has nothing in it to try to start safe mode.  If the problem occurs before the event log service was started.  I tried to uncheck all part 3 applications and services in msconfig.  I'm out of ideas.  Someone has everything?

    I said that I tried to do a restore from the day before and up to two weeks before the updates.  I actually found the problem and he had nothing to do with updates.  My crapped out video card and ATI Control Center was freezing at startup.  So I took out the video card and it starts perfectly.  Thanks for the help anyway.

  • After you have installed the certificate update (9.3.2), I have an incompetent to swipe down my Notifications

    After you install the latest update (9.3.2), I am able not to swipe down from Notifications & cannot slide to Control Center.

    I tried to reset, checked the settings and still cannot get this fixed number.

    For any help or suggestion will be appreciated!

    Thank you for your time!

    Try a forced reboot. Hold down the home and Sleep/Wake buttons simultaneously for about 15-20 seconds , until the Apple logo appears. You won't lose anything.

    If a force restart does not help, try a system restore. First save your device via iTunes. Also import your photos on your computer and copy all the important data. Reconstruction of the support first test and test. If this does not help, you may need to restore as a new and reconfigure from scratch as the backup may be damaged. It is important to have your photos and your saved data separately from the backup. Here are the steps for a restoration:

    https://support.Apple.com/en-us/HT201252

  • Symantec Antivirus Corporate Edition "scan stopped by user" message after you have installed the latest update of Microsoft Security

    I run Symantec AntiVirus Corporate edition 2002 (build version 8.00.9374). The following problem, I discovered yesterday (May 13) when my analysis system and antivirus weekly update is scheduled: from an analysis of the system, the scan box opens and immediately stops, displays the message "scan stopped by user", followed the date & time and all control buttons are grayed out (not functional) with the exception of the close button.

    The only change that took place in my PC has been the download and installation of the most recent update Security for Windows XP (KB978542) which is described as: "critical Microsoft Security Bulletin MS10-030 - vulnerability in Outlook Express and Windows Mail could allow Code execution (978542) remotely.
    (url: http://www.microsoft.com/technet/security/bulletin/MS10-030.mspx)

    I tried to uninstall the security update; uninstall - reboot - reinstall - Live Update of the antivirus application. do a system restore point to return to the previous week - to no. AVAIL.

    I later identified this same, exact problem on 3 other computers running XP with sp 3 which just installed the latest update from security Microsoft.  I would be grateful to any suggestions on how to remedy this situation.  As a newbie to this forum, I would appreciate if others copy this assignment to other sections of the Symantec and Microsoft sites that could give him this attention important issue.

    Thank you

    Bryan Pepper - send me an email to * address email is removed from the privacy *.

    Installation not to run, such as Microsoft Security Essentials Package.

    Can I install Microsoft Security Essentials [or any other anti-virus/anti-spyware application] to clean my already infected computer?
    http://social.answers.Microsoft.com/forums/en-us/msescan/thread/87058857-D181-4019-a723-efd9a49d9275

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • After you have installed the latest update to iTunes, I got an error message: iTunes is not installed correctly Error7

    Original title: iTunes

    I had iTunes running on Thursday passed on W8.1. When he downloaded the last version I received the message: iTunes not properly installed Error7 (Windows error 1114) with: rubtime Library Microsoft end ++. Run-time error. Program: C:\Program Files (X 86) \iTunes\iTunes exe. R6034 An application has made an attempt to load the C runtime incorrectly library. Support team of enforcement contact for more information. When I'm on it 1 time iI uninstalled & reinstalled. Same message.

    Always looking for help. I tried various suggestions does not.

    The answer on Apple Support that solved this for others said:

    "

    Go to control panel > add or remove programs (Win XP) or programs and features (latest)


    Remove all these elements in the following order:


    • iTunes
    • Apple Software Update
    • Apple Mobile Device Support (if this will not uninstall press on)
    • Hello
    • Apple application support


     


    Restart, download iTunes and then reinstall, or under an account with administrator rights, or right click on the downloaded Setup program and selecting 'run as administrator '.


     


    See also HT1925: removing and reinstalling iTunes for Windows XP or HT1923: removing and reinstalling iTunes for Windows Vista, Windows 7 or Windows 8. Some users must follow all the steps in the appropriate support document which includes a few deletions additional manual file and folder not listed above"


    You perform all of these steps? I see that you posted in this forum. You really need to post here.

    __________________________________________________________________________________________________
    Barb

    MVP Windows Entertainment and connected home

    My Blog - http://digitalmediaphile.com/

    Connected world Blog Reader Windows 8 App Barb-
    http://apps.Microsoft.com/Windows/en-us/app/barbs-connected-world-blog/02f35769-52bf-461C-b1d5-06e54a58d298

    Windows and Surface drive Windows 8 App community
    http://apps.Microsoft.com/Windows/en-us/app/Windows-and-surface-community/0abb150e-D287-47d4-837E-9fa51f485ad7

    Please mark as answer if that answers your question

  • From a newspaper article, I realized that Windows 7 would be free updated for Vista Home Premium that was on a computer purchased. My purchase date was 12/28/09 & Best Buy told me that I was not covered. What are the limits?

    Question contains all the info.

    How does the Windows 7 upgrade Option?

    The Windows 7 upgrade Option is available through participating PC manufacturers on some PC and Microsoft on any purchase of packaged product Windows Vista. The Windows 7 upgrade Option applies to Windows Vista Home Premium, Business and Ultimate editions. Your upgrade to Windows 7 will be the comparable version: so you will get either Windows 7 Home Premium, Windows 7 Professional (upgrade to Windows Vista Business) or Windows 7 Ultimate, respectively. The Option upgrade Windows 7 program runs from June 26, 2009 through January 31, 2010. Some manufacturers may choose to shorten the time of upgrade Option.

    http://www.Microsoft.com/Windows/buy/offers/upgrade-option.aspx

    Above Microsoft link has info for the Options to upgrade Windows 7 from participating computer manufacturers.

    Read the info here to see if you qualify.

    http://www.Microsoft.com/Windows/buy/offers/upgrade-FAQ-option.aspx

    FAQ about the upgrade is at the link above.

    http://www.Microsoft.com/Windows/Windows-7/get/Upgrade-Advisor.aspx

    Windows 7 Upgrade Advisor.

    http://TechNet.Microsoft.com/en-us/library/dd772579 (WS.10) .aspx

    Railways upgrade to Windows 7 at the link above.

    http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

    Windows 7 Hardware/Software Compatibility Center.

    For any other question of Windows 7:

    http://social.answers.Microsoft.com/forums/en-us/category/Windows7

    Link above is Windows 7 forum for questions on windows 7.

    Windows 7 questions should be directed to the it.

    You are in the Vista Forums.

    See you soon.

    Mick Murphy - Microsoft partner

  • After you have installed the latest updates of windows for Office 2007, I am unable to open any of my Office programs. I am running XP Pro SP3.

    I deleted the update that caused the problem; specifically, 972581. tried to run repair on the programs; Looks like a reinstallation does not work.
    Office 2003 is not affected.

    Try a direct download of 2 of them and read on the 3rd. http://www.Microsoft.com/downloads/details.aspx?FamilyId=d20004c5-dd01-459e-8120-5f127e20c085&displaylang=en

    Update of security for the viewer Microsoft Office Visio 2007 (KB973709)

    http://www.Microsoft.com/downloads/details.aspx?FamilyId=EC802723-F2B2-400A-A24D-8D8D9092F9EA&displaylang=en

    Update of security for Microsoft Office System 2007 (KB974234)

    http://support.Microsoft.com/kb/972581

    Info on KB972581

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Read this if your error Code 646, including all positions and solutions offer to this thread link below:

    http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/f3390e74-9961-4AAE-8a05-554c1a9cf1a2

    Read the info on the above link to error Code 646.

    With the compliments of: David_O - Support Engineer

    This problem occurs when the agent Windows Update Wups2.dll file is incorrectly registered in the registry. Because registry files that correspond to the Wups2.dll file are missing, update facilities have failed. There are two methods to resolve this issue, use method 1 first, and if it did not resolve your issue, go to method 2

    Method 1: Save the Windows Update files

    1. click Start and type notepad in the box start the search .

    2. click on Notepad in the programs list.

    3. copy the following commands, and then paste them into the opened Notepad window:

    REGSVR32 WUPS2. DLL/S
    REGSVR32 STINKS. DLL/S
    REGSVR32 WUAUENG. DLL/S
    REGSVR32 WUAPI. DLL/S
    REGSVR32 WUCLTUX. DLL/S
    REGSVR32 WUWEBV. DLL/S
    REGSVR32 JSCRIPT. DLL/S
    REGSVR32 MSXML3. DLL/S

    1. in Notepad, on the file menu, click on record under .

    2. in the list record under , click all files .

    3. in the file name box, type register.bat .

    4. save the Register.bat file to your desktop.

    5 right-click the Register.bat file, and then click run as administrator . Collapse this includes this image if you are prompted for an administrator password or a confirmation, type the password or click continue .

    6. try to install the updates again.

    Method 2: Download and install Windows Update agent

    For more information about how to download and install the latest Windows Update agent, click on the number below to view the article in the Microsoft Knowledge Base:

    949104

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Please rate me upward if you find my post helpful. Thank you!

  • Any update on the problems with Safari after you have installed the new update?

    Any update from Apple. How long this problem will be resolved?

    What is the problem?

  • After you have installed the dss x 8 netrome, can't connect to Windows

    Original title: dss x 8 netrome

    I had to reinstall the software that knocked my user id and password and I think that the default user is admin but don't know what the default password is... tried 000000000

    Took me about four hours before I thought about it.

    I have the same system accurate and encountered the same problem as you.

    SUP: admin

    P: 1111

  • KB955759 does not appear when I check the updates manually, but it appears with the yellow shield after you have enabled the automatic updates.

    original title: Windows Update acts confused - kb955759 does not appear when I check the updates manually, but it appears with the yellow shield after you have enabled the automatic updates.

    I just reset my CMOS settings, writing zeros for my hard drive, repartitioned, reformatted and used the recovery cd Gateway system to get my computer to Windows 98se - factory settings, except at the beginning of the recovery of the system, when it says "press any key for advanced options," I pressed a key and then I unchecked all the default (3rd party) applications including Norton and left only 2 checked: "Updated USB Hub" and "Windows Shutdown Supplement," while nothing has been installed, leaving only win98.
     
    Then I used my disc XP Home (SP2) update.  I, immediately after the upgrade to Windows XP, installed "Office XP with Frontpage, Developer Edition", then Norton 2012 before never connect to the internet.
    Then, I connected to the internet and continuously update of Norton, before ever hitting the Windows Update page. The first thing I did then was to activate Windows, and then activate the office.
    Then I hit the update of Windows "button" that says "get all your updates in one place... upgraded"Microsoft Update".  I, then, just kept hitting the page update and restart, until I find the SP3.  Then, I took a break, until the next day.
     
    I have an ADSL broadband, with a Linksys EtherFast PCI card.
     
    Then I got SP3, which installed without any problems.
    So I just kept "microsoft continuous update" manually (and reboot), until there is no more updates - EXCEPT, I always uncheck Windows Malicious Software Removal Tool - which was the only screening at the final stop for the night.  I think that I ticked the box "don't ask me about this update".
     
    Then, in the morning, after you have enabled automatic updates, I noticed the yellow shield - Windows security icon (or whatever it's called), so I clicked on it and checked it was tellimg me was available [when I checked "Custom Install (advanced users)"].  What showed was 1 update - 955759 KB.
     
    After the problem, already at the reformat (months and months), see the yellow shield telling me there are updates available, which were already installed (before rebooting), I checked manually on the internet with IE 8, pressing alt, "T", "U".  There is no updated list.  Then I checked through my history of update (twice), and KB955759 had not been installed.
     
    My update setting is to let windows download ('important') updates, but let me choose when to install them.
     
     
     
    What is the right - Windows Update (NO update important reporting) Site, or the yellow shield (reports [a] kb955759 [update])?
     
    I can not yet confirm he is supposed to be an update for XP home kb955759, because I was unable to locate any detailed documentation on this 'thing' that protect the yellow safety seems to think is a significant update.

    Comment 1: To my rquest, a moderator merged your thread in the Sub-forum Win7 updates with your wire in the Sub-forum of updates of Windows XP 20 Feb-12, c. 07:50 UTC.

    Comment 2: If you will not contact the MS Support on this issue?

    ~~~~~~~~~~~~~~~~~~~~~~~~~~

    Just for the heck of it, I have disabled the automatic updates, cleared my browser cache, checked manually, updates from microsoft (windows) and found none (with the exception of software malware removal tool windows [which I have not installed]).  Then, I turned the automatic updates on, and without even being connected to the internet, the yellow shield popped up with the kb955759 "update"...

    Repost...

    1. If you open Internet Explore (only!) to http://windowsupdate.microsoft.com and run a CUSTOM scan, KB955759 appears in results?... If so, you manage to install it and/or security updates available?

    2 after no. 1 above [<>], is the 'yellow shield' icon appears in the Notification area (on the left of your clock)?  .. and if yes, by clicking on the 'yellow shield' icon tells you that KB955759 or any other updates is ready-to-be-installed?  .. .and if so, you manage to install it?

    3 after doing 1 # & #2 above [<>], is KB955759 or any other updates offered as a ready-to-install update when you go off your computer?  .. .and if so, you manage to install it?

    ... I guess that clearing the browser cache does not erase 'downloaded' updates.

    Nope. If you want to clear the queue of the update...

    OPTION A:

    1. stop the automatic updates service:

    Start > run > (type or copy/paste) services.msc > click OK
    Double-click automatic updates > click stop
    (Stopping the service will take a moment)

    2 remove the contents of the download folder:

    Start > run > (type or copy/paste) %windir%\SoftwareDistribution > click OK

    Open the download folder and delete its content
    Close the window.

    3. start the automatic updates service:

    Start > run > (type or copy/paste) services.msc > click OK
    Double-click automatic updates > click Start
    (Starting the service will take a moment)

    OPTION B:

    1. open Internet Explorer (only!) to http://support.microsoft.com/kb/910336 [don't know the titles, etc..]

    2. make disappear/close the Troubleshooter automatically pop up.

    3 repaired 50202 in DEFAULT modes and AGGRESSIVE. [1]

    4 reboot.

    Does anyone know how to determine if software mailicious removal tool is installed on XP? [source ]

    Check the located log file...

    C:\Windows\Debug\ MRT. NEWSPAPER <>

    Related...

    ... This leaves us with the malicious software removal tool don't appear not.

    I guess I'll have to leave "auto-update" (I often have less than 65 M of free memory left and do not have enough memory to msrt) and don't assume no other current error. [source; 17 Aug-11]

    It's no wonder that you ended up having to do a clean install of Win98SE & then upgrade to Windows XP again!

    ================================================================
    [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not updates installed in Add/Remove Programs list.

  • Problem has been detected and windows has been shutdown error STOP: 0x0000008E. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

    Original title: problem has been detected and windows has been shut down. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

    Computer Message: Check if you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

    Check with your suppliers of material, updates the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to start advance startup options, and then select Safe mode.

    Technical information: * STOP: 0x0000008E (0xC0000005, 0x8054556C, 0xADB78A98, 0x00000000)

    Beginning physical memory dump

    Total physical memory dump. Contact technical support for further assistance group.

    Hi fernandomventura,

    Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...) Except the keyboard and mouse and then start.

    If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

    Step 2: Follow the steps mentioned in the articles below which deals with a similar question

     

    General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"-restore the system to achieve ".

    http://support.Microsoft.com/kb/945658/

    You receive a random "0x0000008E" error message on a blue screen in Windows XP

    http://support.Microsoft.com/kb/827663

    Thank you, and in what concerns:

    Ajay K

    Microsoft Answers Support Engineer

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • After you have installed the Realtek drivers, I get code 10 error and cannot start sound.

    original title: help with my sound please

    After you have installed the realtek driver it says code error 10 can't start sound...

    also I can't find the button sound.video and games on the Device Manager heres the message in Event Viewer:
    Log name: System
    Source: PlugPlayManager
    Date: 17/05/2012-18:50:27
    Event ID: 12
    Task category: no
    Level: error
    Keywords: Classic
    User: n/a
    : My computer
    Description:
    The device ' in Build Conexant Type 2 modem "(HDAUDIO\FUNC_02 & VEN_14F1 & DEV_2C06 & SUBSYS_10250126 & REV_1000\4 & 37d33e44 & 0 & 0102) disappeared from the system without first be prepared for removal.
    The event XML:
     
       
        12
        2
        0
        0 x 80000000000000
       
        435
        System
        badimo-PC
       
     
     
        Modem Conexant - in the generation Type 2
        HDAUDIO\FUNC_02 & VEN_14F1 & DEV_2C06 & SUBSYS_10250126 & REV_1000\4 & 37d33e44 & 0 & 0102
        00000000
     

    Hello I want to,

    The problem you describe looks like you are maybe install the wrong driver for your sound card.
    Have you checked that the driver is for your specific device?
    If you look in your system's Device Manager, is there a yellow exclamation next to the audio controller?
    If so, this seems to indicate that the drivers installed are not good for your sound card. Usually if you double-click the device in Device Manager, it will say something in the sense of "Device cannot start".
  • I have installed the latest updates for my Compaq desktop computer and the DVD/CD drive bay door will not work.

    I have installed the latest updates for my Compaq desktop computer and the DVD/CD drive bay door will not work. I can get the led light will stop flashing when I open the door all the way, the machine detects the drive but do not read or close on its own, how can I get this disc surgery? Downloading updates, I installed a software disc, when I ejected the disc, the drive comes of is stopped. The computer still sees the drive, but will not read or even close on its own. I also had been using my computer in mode mute until I tried to increase the volume and now the computer tells me no playback device installed. Device Manager acknowledges the Harmon/Kardon soundsticks connected to it, but nothing does, how it works? The Control Panel also sees the soundsticks, but still when I try to move the volume the computer says there is no playback device installed.

    Hello

    1. do you get any error code or error message?

    2. what day you installed recently?

    It seems to be a problem with the hardware. I suggest you try to uninstall and reinstall the CD/DVD driver and check if it helps.

    Follow the steps to uninstall and re-install the drivers.

    a. click on start toreduce this includes this im and then click Control Panel.

    b. click system and Maintenance, click Systemand then click on Device Manager.
    Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

    Reduce this includes this imageIf you are prompted for an administrator password or a confirmation, type the password, or click allow.

    c. in the Manager device, expand CD-ROM/DVD-ROM drives, right click on CD and DVD devices and then click Uninstall.

    d. When you are prompted to confirm that you want to remove the device, click OK.

    e. restart the computer.

    If the methods mentioned above did not help, then it would be best to contact the manufacturer of the computer/CD/DVD player.

    Hope the information is useful.

Maybe you are looking for

  • Satellite M35x: while the AC adapter is plugged in the battery start to unload and beep

    Hello I'm having the same problem as this person here...http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=15116My Toshiba Satellite M35x, when it is plugged in, just start discharge and beep.He always did regularly, like every tw

  • Bluetooth A2DP audio playback crashes every 5 seconds (Portege R500 VistaSP1)

    Hello I fully reinstalled on my new Portege R500 Vista SP1and newest Bluetooth 6.10.10. When playing music from an A2DP Bluetooth audio output device with Mediaplayer music is still suspended every 5 seconds. With my cell phone this A2DP audio device

  • InstallComCallback

    Hello I'm sorry if this question has already been asked but I'm trying to decotiquer a piece of encoder written on CVI and there are a few concepts that venture. Also I wonder the quetsion about the role of the function "InstallComCallback". D 'after

  • Setting voltage hp3649 in IVI TS 4 steps

    I'm trying to set the level on the power supply for hp3649 in simulation with NI IVI driver mode. The configuration and the measure properly. When you try to use the software to change the level of tension without change occur and spy NOR shows any e

  • setting up parental controls in windows vista Yahoo Messenger using esp

    I just bought a new machine and I am trying to set up parental controls. I have windows Vista Home Premium... When Parental control is disabled, YM works, but when it is turned ON, even if the setting is "Allow all Web sites" (which is not make sense