AHCI RAID mode change

Similar Questions

• Change the SATA controller AHCI RAID mode

  HP Pavilion 6267c desktop 750 gb HD failed.  Installed Seagate Barracuda 1 TB HD.  Cannot change the controller SATA AHCI RAID mode.  System hangs.  Desktop works when he returned to RAID.

  Any help is appreciated.

  Hello

  Hope this helps:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/changing-from-RAID-to-AHCI/4c94f678-6BD1-48a6-b871-8872c841023a

  Good luck.

• Windows Server 2008 R2 SP1 AHCI RAID change

  Hello

  OS: Windows Server 2008 R2 SP1
  Storage: 1 x SSD
  Tip: Supermicro X9SRW-f

  Currently, the SATA in the BIOS option is on AHCI. Start Windows on the desktop without problem.

  Objective: Convert AHCI Raid mode. The integrated chipset to create a matrix to mirror with 2 x SSD.

  I downloaded the disk driver for this card and installed the Intel Rapid Storage driver/software. I reboot and switch the SATA Raid mode. Windows starts to load and immediately blue screens. Put the SATA to AHCI mode allows me to boot successfully.

  There are a few other drivers from the disc. Install these drivers, the windows are no longer boot in AHCI or Raid mode.
  iaStorA.inf: installs rest AHCI Raid Controller Miniport + RTS filter driver
  iaStorB.inf: installs rest AHCI Raid Controller Miniport + RTS filter driver

  HKEY_LOCAL_MACHINESystemCurrentControlSetServicesMsahci\\\ (set to 0 Start)
  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV (set to 0 Start)

  How can I activate the raid option and get Windows to start without error? Registry hack? Other drivers?

  * Note the OS has been cloned for the SSD. I don't have the option for the new Windows installation.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Changing to AHCI RAID

  Hello

  my Dell E6510 I have my hard drive put in RAID mode. I have problems using the eSata port, so I want to switch to AHCI. I followed the instructions here:http://support.microsoft.com/kb/922976. However, when I start my system after setting the drive in AHCI mode in the BIOS, I see the logo of Windows (with Win7 x 64) and a few seconds later, I get a blue screen with a message that I can not read because the system is restarted. Put back the BIOS on RAID brings the system again...

  Anything I can do to work AHCI?

  Thank you

  Thomas Pagel

  Hi Thomas,

  Thank you for your message.

  I think I have the solution to your problem and I checked it against a machine Dell which is equipped with a similar controller with your machine. Changing to AHCI, RAID,http://support.microsoft.com/kb/922976 fix will work.

  Changing to AHCI RAID, you need a little more. Msahci driver requires Atapi.sys miniport driver to load during startup as well. If you must change the value ofStart at 0 for the following two entries in your registry. You can use regedit.exe utility.

  HKEY_LOCAL_MACHINESystemCurrentControlSetServicesMsahci\\\
  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\atapi

  Or alternatively, you can run the command lines below in a high window.

  REG ADD HKLM\System\CurrentControlSet\Services\msahci /v start d 0 /f /t REG_DWORD
  REG ADD HKLM\System\CurrentControlSet\Services\atapi /v start d 0 /f /t REG_DWORD

  Concerning

• HOW TO CHANGE SATA to RAID mode (SSD CACHE PROBLEM)

  Hello

  I have a HP Envy 4 1054tx Ultrabook with 500 GB drive HARD + SSD of 32 GB. My HARD drive crashed and replaced it with a new one. Unfortunately, my restore disk does not work so I installed fresh new WIN7. I try to use the SSD caching capability of my laptop (which he did before, when I bought it).  Based on the forums I've read, the SSD cache implementation requires that the SATA controller must be set to RAID mode.  However, when I entered the BIOS, there is no option or the configuration that I can use to set SATA RAID my HARD disk mode.  In this regard, I can't meet one of the requirements of SSD caching.  Here are some of my BIOS Setup.  Can you help me please guys how to work on it? I am not convinced, on how my phone performs without SSD caching.

  Thanks in advance.

  

  Hello:

  Disk controllers hard HP consumer notebooks cannot be changed from their default values.

  More than likely if your model is equipped with a hybrid drive, the speed control is already defined with RAID.

  I recommend you to read this blog on how to get this Setup to work on a new install of W7.

  http://Forum.NotebookReview.com/HP-Pavilion-notebooks/676213-definitive-guide-clean-install-OS-MSSD-cache-equipped-laptop-dv6t-7000-dv7t-7000-Envy17-3200-a.html

• U410 Lenovo - replace AHCI RAID

  Hello world

  Does anyone have solution Chipset SATA Mode to AHCI RAID change?

  Since yesterday I try to find the appropriate solution for this issue.

  I already checked:

  (1) change of tone to register as above;
  Departure from HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\storahci 3-> 0
  Start HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\iaStorA 0
  Start HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\iaStorV 0
  Error HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci 3-> 0 control

  Unfortunately after the restart in RAID mode, operating system does not work.

  (2) to go step by step on the description made by the microsoft support team:
  support.Microsoft.com/kb/2751461?wa=wsignin1.0

  Does not work.

  My goal is to set up my SSD as cache drive and I read - without changing the RAID mode, it wouldn't work.

  I appreciate your advice.

  Maybe there is a possibility to set up the SSD as cache in AHCI mode?

  Problem solved

  I had to change the start on 'legacy of first' Mode.

  You can close this topic.

• Can I use instead of AHCI RAID

  Hi, I have a dell inspiron 530. In the bios there is no option AHCI. Since the RAID AHCI she does that mean I can use the same?

  PS: I have 2 hard drives (no RAID). I tried to boot into windows on the first hard drive, but then it froze on startup a BSOD flashed for a few milliseconds and then he resatrted.

  Thank you.

  Hi John,.

  Thanks for posting your question on the Forum of the Microsoft community.

  1. have you tried to change the boot drive SATA mode?
  2 are you able to boot your computer?

  3. What is the error code that you get when getting BSOD?

  I understand you have two independent hard drives connected to the controller. If you are able to start your computer successfully, here is an article that can help you change AHCI RAID.
  Error message occurs after you change the mode of the boot drive SATA

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  If you can not start at all, I suggest trying the following methods and check if they are useful.

  Method 1
  Please follow the underlying steps:
   
  Step 1. Disconnect all external devices except the keyboard and mouse.

  Step 2. I would like to start your computer in last known good configuration.

  If method 1 does not work, go to method 2.

  Method 2
  Step 1: Try to start your system in a State of services necessary to the operation and a minimal set of drivers, active Mode without failure.
  Start your computer in safe mode

  Step 2: If the system works fine in safe mode, try to clean the system startup:

  How to perform a clean boot in Windows

  Note: See "how to reset the computer to start normally after a boot minimum troubleshooting" to prepare the computer to start as usual after a repair.

  If method 2 does not work, go to method 3.

  Method 3
  As you cannot start your computer at all, I suggest to run a startup repair to repair the damaged boot system files and attempt to start in normal mode. See the section: how to use Startup Repair in the following link.
  Startup Repair: frequently asked questions

  If this does not help, try to start from an installation disc of Windows 7 to the Windows recovery environment mode and then try to run the Startup Repair tool and check if you are able to start normally.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you further.

• Server installation 2012 on PowerEdge T110 II in Raid Mode

  I am trying to install Windows Server 2012 on a server PowerEdge T110 II that I just bought.  No software utility disk and the driver provided with the computer!  When I try to install Windows directly from the OS installation disc it tells me that some drivers are missing however it does not list all the specific missing to find out what is missing!  The message reads: "a media computer driver needs is missing."  This could be a DVD, USB or a disk in hard disk driver.  If you have a CD, DVD or USB flash drive with the driver on this subject, please insert it now... »

  I read in Guide_en of the user Instructions 2012_Installation your Microsoft Windows Server-we document that I need 7.2 OpenManage that supports the installation of operating system Windows Server 2012.  I got the ISO of OpenManage 7.2.0 A01 from your Web site and burned it to a DVD.  I started the computer with this DVD and was able to get for Dell Systems Build and Update Utility.  From there, I went to set up against Installation OS Server.  It provides a list of supported OS.  Windows server 2008 and 2011 are listed but not 2012!

  When I go into the BIOS (PERC S100, version 2.2.3) and change the setting of SATA in ATA and run OpenManage and go to Dell Systems Build and update utility and configure the server against, to presents this time Windows Server 2012 and I am able to go further until it gets to 100% full and restarts.  I insert the installation of Server 2012 DVD during the reboot and it states that "the valid operating system installation media was found.  Press 'OK' to start to install. "A system Build and Update Utility message appears which States:"the temporary Partition is removed.  If an error occurred during the installation of the operating system, you will need to use the Systems Build and Update Utility to restart the installation process. "I press OK and get a Windows Installer message that says:"the file 'autorun.dll' could not be loaded or is corrupt. Setup cannot continue. Error code is [0xC1] 'I burned the DVD of the BONE from an ISO from Microsoft.  I read that maybe the DVD must be burned differently and at a slower speed.  Who can solve this question (not sure yet), but I would like to configure this computer in RAID mode anyway, and first I have to solve the following question:

  (1) is it still possible to install Windows Server 2012 with the Raid Configuration on this material?  If so, how?  The OpenManage--> Dell Systems Build and update utility--> set up against server does not list server 2012 unless the SATA is not set to RAID!

  (2) when I set up the same computer with Server 2012 as the operating system installed on the site configure from Dell.com and to buy, it gives a configuration error that says "error: 2012 options selected operating system from Microsoft require Microsoft 2012 media.» When I pick/check ' Windows Server 2012, edition Foundation, press release "the error disappears.  Do I need this press kit?  -What is the origin of the problem with the installation?  And where can I get this missing element?

  Any guidance you can give me or reference to material appropriate/docs for help would be appreciate because I have lost/spent several days trying to get this installed server operating system!  Thank you.

  The T110 II is almost two years, then Yes, compared to 12 G systems, is using older hardware (I suspect that replacement is the T110 II should be out soon).  The S100/S110 is a special implementation of Intel RAID on board, so the S110 is not an option on the older boards that have the S100.

  ftp.dell.com/.../DELL_MULTI-DEVICE_A05_R294489.exe

  Good luck.

• a speed of read/write DAQ card mode change will reach 200K

  HEY, man,

  I have a project needs to test two points I name them point A and point B, the first time, I should point A 5V DC input, voltage inductive test point B, sencodly, give point B 5V DC input and inductive point test output voltage, this means and two analog ports must read and write sharing mode , and the test speed must be 100 KB, if I have a 200 KB data acquisition card, can the speed of read/write mode change reach 100 KB for an analog port? or, please give your suggest for my this kind of situation, thank you.

  Hi API,.

  I see that you are trying to measure voltages using a single channel at a time on a data acquisition card.

  Unfortunately, you cannot change the inputs to the outputs or vice versa on a map of data acquisition, they are static.

  What I recommend is either using a switch like this: http://sine.ni.com/nips/cds/view/p/lang/en/nid/207130 where you will need a high chassis.

  Or, having four channels, 2 inputs and 2 outputs and try to measure it. You should have the necessary speed as well.

  If you have any other questions, I'd be happy to answer.

  Thank you very much

• Server 2008 AHCI RAID

  Hi all

  I'm trying to migrate to Windows Server 2008 AHCI RAID on motherboard Intel S5500BC, I downloaded the driver ERT2 of intel, and when I want to add new hardware, and then search for the driver, the driver is not detected! I tried enabling megasr in the system registry and still windows begins with BSOD, is there a driver or a workaround for this problem, I don't know if I'm in Community law

  Concerning

  Hi Muhieddeen,

  I suggest you post your query in the following TechNet forums to improve assistance in this regard.

  https://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

  Thank you.

• Lenovo IdeaPad U310 install Windows 7 Professional in RAID mode

  Hello community,

  I need to install windows 7 pro on my brand new IdeaPad. But still, when I start installing windows from USB, it is said: no hard drive. Can you tell me, what is the right driver from Intel for the installation of windows 7 pro in RAID mode?

  TUST me, the GTP partition table will drive you nuts.

  Use Windows 7 at any time update and insert your Windows 7 Pro key. This will transform your Home Premium Windows 8 Pro.

• Which raid mode is the best performace with security for ESX OS?

  Hi all

  I need to rebuild the ESX OS, so I would like to know what raid mode is the best performace with security for ESX OS?

  No need to consider the capacity of the disks or numbers, just discuss the performace with security as raid 1 10 01 5 or 6?

  THX

  Hello

  Almost THEM are running with RAID 1, it's the default installation.

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

• Protection Mode change Data Guard.

  Experts,
  
  Ask your entries on the Data Guard protection mode change, below, is our environment:
  
  BECAUSE with two nodes: primary
  Single stand-alone Server DB: Eve
  Apply real-time: enabled
  
  For the primary and Standby databases, it's protection guard data display "Maximum Performance" mode. According to our needs, we would go for "maximum availability". I can go ahead and change, however I have questions in mind before making the change.
  
  1. do I need to change the protection on both primary & standby mode?
  2. do on DB primary change automatically the standby mode too?
  3. If the answer is NO to the 2nd question, I need to change the mode of protection to standby also? In the otherwise, primary and Standby will be run in two different modes.
  
  Please let us know of your entries.
  
  Thank you

  Crazy.

  I'm really happy that it works. Only ORA-16198 has very little information about it.

  And its raining in the North tonight so I have to escape before it turns me on.

  Best regards

  mseberg

  Subsequently

  Is equivalent to checking. Hoping no news is good news.

  I've seen this thing before restarting. Last weekend was indeed an Oracle 10 bark at me during the installation of the entire network has been good. Another error, but I finally tried the same thing and it worked also. No complete sense to me, you would think that the listener would govern. And then it takes the real is what's real.

  MS

  Published by: mseberg on December 14, 2011 18:47

• Changing to AHCI RAID Windows 8

  Hello
  on my Lenovo U310, I have my hard drive (HDD) set to AHCI mode. I want to change RAID (0) mode because I have an SSD and can I use the Intel RST with this machine.
  The problem is that when I change the mode in the BIOS appears the BSOD in an infinite loop and disappear only when I put the AHCI mode again.
  I have tryied with methods of Windows 7 registry with changes alleged Windows 8 but it doesn´t worked.

  I hope that someone can help me.
  Thanks,

  Andrés Miranda

  P.D: The "alleged" modifications for Windows 8 were these:

  Change: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\storahci Start to 0 (in the subvalue)
  Change: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\iaStorA start at 0
  Change: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\iaStorV start at 0 (in the subvalue)

  Hi Andres,

  I suggest you post this question in the Pro TechNet Forums Windows 8 IT: http://social.technet.microsoft.com/Forums/en-US/category/w8itpro

  Thank you.

• HP Envy 15-j001sr: SATA controller in AHCI or RAID mode?

  I wonder, does anyone know how the SATA controller located in

  HP Envy 15-j001sr (E3Y72EA): in RAID or AHCI mode? I buy this laptop and planning to upgrade to SSD.
  Upgrade advice will be highly appreciated.
  What is better: to clone the HDD SSD before initial start-up
  Or install Windows8 first, bring a USB recovery set, then make Windows8 recovery after the installation of the Virgin SSD in?
  Thank you for your help in advance.

  Hello

  It uses a single disc HARD must be the AHCI mode:

  http://support.HP.com/us-en/document/c03846066

  You can configure it as you want, including create whole recovery dics and THEN clone the disk SSD. After that trade them. This will save time and you can be sure that the rollback/uninstallation less pain if necessary.

  Kind regards.