Aironet 1850 as a standalone (mobility express master)

I just bought a new AIR-AP-1852I-E-K9 for waiting room.

I've never had a Cisco product before. We have always had some before cheap consumption points.

I plugged the AP to the POE and it gets an ip address. But the SSID CiscoAirProvision will not be displayed.

After much research, I'm a bit confused. Maybe someone can help me.

-To learn more, I have the wrong firmware on my AP I have need to install the mobility Express version so the AP can act as stand-alone.

-The correct firmware would be

-I have no contract with cisco, so I can't download this firmware. Why does take a contract to download the Cisco software?

-J' tried to ssh to the AP with PuTTY to know whether what version is currently installed on the ap but I can't connect to it.

Any help would be highly appreciated and sorry for my English.

Send you mail, respond with precision, will help you download.

Tags: Cisco Wireless

Similar Questions

  • Option admin status when creating a new WLAN mobility-Express

    We have three Aironet 2802i, where one of them is running mobility Express.  (One of them seems to have hardware problems while we get it replaced, but that's another story...)

    When you configure a new WLAN on a mobility Express, which is "Admin State" for?  I was not able to find on the Guide to me what that really means.

    In addition, there is a documentation on ME running on a 2800's?

    Thank you


    Hi Dennis,

    The "Admin State" configuration option is used to toggle the WIFI. Keep it as "Enabled" will cause the SSID to the AP and diffuse.

    Can you let us know what specific documents are looking for wrt ME on 2800?

    Best regards

    Learn from the best to be the best!

    Join us on LinkedIn to access our free tech-conferences and training resources!

  • Conversion of Cisco Mobility Express Bundle


    I have a question about the Cisco Mobility Express Bundle (not the device without mobility Express on 1800 series AP). When the beam is bought, is the software on the 2500 WLC a cut version with the day Setup Wizard 0 and the new dashboard or is it the full version of the software that would be the same when you buy a stand-alone 2500?

    Thank you


    According to my knowledge, it will be with the full version of the software that would be the same when you buy a stand-alone 2500.


    Remember messages useful rates

  • 1850 mobility Express

    I would like to propose the new mobility Cisco 1850 express solution. According to my understadning the 1850 built in the virtual controller for up to 25 AP and info is transmitted via wifi to the next access point.

    My question is what do I do if the AP is not in the master of 1850 AP wifi range? the AP will continue to receive information of the 1850? or in this scanario ill have to go to a conroller tradiionnels as the 2500 series?

    No, perhaps to make you believe otherwise is the fact that the PA primary, while acting as a controller, is always as an AP and clients can connect to him in this way.

  • Defining a 1852nd Aironet AP - Radio Off - Cisco IOS 12.3 (4) JA

    I have a brand new Cisco Aironet 1800 AP series I'm trying to install. Specifically the 1852E. I do not have a controller and try to use the method of deployment of mobility Express. When I received the unit there is a yellow label more precisely declaring outside: "OFF BY DEFAULT note RADIOS: radios are disabled by default for Cisco IOS releases 12.3 (4) JA and later.

    If anyone can please tell me how I am supposed to this access point configuration when the radios are not suite, so the CiscoAirProvision SSID is not broadcast?

    I tried the following:

    1 connect the unit to my PoE switch. Unit Gets power and discovery mode starts (red/orange/green light cycling). He succeeded receives an IP address from my DHCP.

    2. when I try to access the device through my laptop via the local LAN it just times out. Pings meet.

    I apologize if my post seems harsh, I am quite agitated that even after having spent more than 5 hours trying to troubleshoot and get this thing to work, there was nothing else than a nightmare (both for the installation of touted 10 min). I do RTFM. I missed something simple jumps? or am I just to assume that Cisco has really missed the boat the patch appropriate for an assignment in their literature.

    FOR INFO. Thorough searches Google and research on this forum gave me no help.

    Thank you.

    Convert a CAWAP AP an AP express mobility

  • Cisco Aironet 1830 disable broadcasting of the SSID

    I recently bought a Cisco Aironet 1830 with the mobility Express version. installed This unit is my controller and my only AP. I configured the device, but I can't seem to find a setting in the GUI or the CLI of the controller or AP disable broadcasting of the SSID. Can someone help with this?

    Thank you

    The CLI is available, the following command:

    config ssid broadcast disable wlan where wlan id is the number of your wlan. If in doubt, do a show wlan summary which should give you this info, I hope.


  • Blue screen! Cannot install XP on Intel HM65 Express Chipset Family LPC Interface Controller - 1 49

    Recently I bought the HP DV6 with Windows 7 pre-installed. I want good old XP OS to which I am addicted.
    F6 function fails for chipset HM65 with "Intel (r) Mobile Express Chipset SATA AHCI Controller" is the machine based on Win7, but I like XP and tried to install it using F6 utility and the latest driver SATA from Microsoft download center.
    But whenever I encountered BSOD with the message "STOP: 0X0000007E (0xC0000005, 0xF73B9D66, 0xF78B1EA0, 0xFF71B1B9C)"
    Another mistake, shown on the BSOD screen is "acpi.sys - address F73B9D66 base at F73AE000, datestamp 480252b 1.

    I tried many a times by "slipstreaming" the SATA Driver detected at Microsoft and by using the floppy USB F6 also drive. But I'm unable to load Xp on the machine.

    Whenever the operation of F6 when I select the option "Intel (r) Mobile Express Chipset SATA RAID Controller I met the BSOD and the establishment fails.

    kindly advise me with an appropriate method to install xp on my HP machine whose bios is locked or disabled for change the IDE to AHCI RAID.

    Thanks in advance

    I suggest you to refer to this link and check if it helps:
    It will be useful.
  • Unable to get quick installation of mobility on 1832 AP

    Model is 1832I-B-K9

    I can't get the AP to start for mobility Express.  I have AP installed on a completely isolated network, so it becomes an option 43 DHCP, DNS or L2 response broadcast resolution from a controller.

    Switch a local DHCP server configured on it, and AP receives an IP address.  Watch the output from the CLI, I see the AP obtains an IP address, moves into the State of discovery and remained several minutes before reboot and start the whole process over again.

    I also tried to wipe the config by holding the Mode button for 5 seconds, but still get the same results.

    Here is some more info from a version of the show:

    AP3820.5682.2F20 operating time is 0 days, 0 hours, 2 minutes
    Last recharge time: Mon May 16 01:14:15 UTC 2016
    Reload last reason: triggered capwapd restart
    Cisco AIR-AP1832I-B-K9 ARMv7 Processor rev 0 (v7l) with 997136 / 784820K bytes of memory.
    Card processor ID KWC193805BX
    AP running Image:
    Main boot image:
    Backup boot image:
    2 gigabit Ethernet interfaces
    2 802.11 radios
    Radio FW version: 0a4f55efe8a32b394e3881a2a53a5db0
    NSS FW version: NSS. AK.1.0.C4 - 00026-E_custC - 1.24160.1.29595.1

    In addition, I have a 3802I-B-K9 who behaves in the same way... :-(

    For any help or suggestion of the group is greatly appreciated...

    Thank you!

    K9C is by default explicit mobility, you need to install manually express mobility in 1832 to K9.

  • Cisco Aironet 1131AG and measure access points to the power of the wireless signal?

    / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

    / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

    We have about forty points of access Cisco Aironet 1131AG spread over four floors and they all have a static IP (BVI1) on the same SSID, customers will be on its own virtual local area network (dhcp on 3750 switch) and they use several channels (1,6,11).  Cisco Wireless Control System is pending. This wireless network should support roaming for customers (there will be Wi - Fi tags of multiple AeroScout and wireless laptops). To measure the strength of the wireless signal and wireless coverage on each floor. My questions are:

    1. How to measure the strength of the wireless signal: we must meet at least three APs available with signal excellent (I guess for the WCS needs that will determine the position of the client in the building)? We thought to use NetStumbler and a few laptops with wifi and measure as many points as we can as simpler thing. Or should we use something like Cisco Aironet Client adapters for our mobile phone and then use Cisco Aironet Client Utility (is it worth buying for our analysis and measurement)? Any other idea?
    2. What signal level should we consider for a good wireless (dBm)?
    3. That we should propose for authentication, authorization and management accounting? What happens to the roaming wireless? I did not quiteunderstand WCS, WDS and WLC-that should be used for above tasks?

    Thanks in advance.

    "Use the command on the AP" sh dot11 associations "will give you the clients associated with success.  If you add the MAC address of the client at the end of the command, you will get detailed information.  Look under "Signal Strength" and "Signal to noise".  Under the strength of the Signal, you want a value of-75 dBm or lower (lower values the better).  -76 dBm and is bad.  Under Signal-noise, you want a value of 25 dBm or more (values higher the better).

    To measure the strength of the signal, I use Airmagnet, but you can use Netstumbler or Cisco Wireless Site Survey.

  • Problem with Accelerator Mobile persistence A-team

    Hi all

    I try to use persistence for the A-team Mobile accelerator. But when the generation through scrip of Ant, he demonstrated error and Build is failure.

    Can someone help me on this.

    [javac] Compiling 95 source files to F:\JDeveloper\mywork\mobile-persistence-master\mobile-persistence-master\Projects\Framework\Runtime\classes
        [javac] javac: invalid target release: 1.8
        [javac] Usage: javac <options> <source files>
        [javac] use -help for a list of possible options

    Kind regards



    Mobile persistence Accelerator A-team uses MAF 2.1 and Java 8. Looks like you have not (completely) install Java 8 and MAF 2.1 yet. You can check your installation?

    Steven Davelaar.

    Oracle Mobile A-team.

  • Cisco AP purchase Questions

    Hello! I am looking to buy a single Cisco Aironet 1852 and use Mobility Express. Is the number of a particular product, I'm looking at AIR-AP1852E-A-K9.

    (1) are additional licenses needed to use mobility Express?

    (2) what is the difference between AIR-AP1852E-A-K9 and AIR-AP1852E-A-K9C?

    (3) I'm trying to find the data sheet for this particular access point and looks like I have to be a partner of Cisco. I thought that the sheets are available for all. Am I missing something? What happens if I try just to watch the product numbers?

    (4) if I buy this particular Cisco access point, does with a support contract or should I buy one? I can't go without buying a support contract?

    (5) the free tools I can use for the best placement of WiFi AP?

    Thanks in advance!

    1 NO.

    2. do not.

    3. this URL does not access partner.  It takes you to the indoor access points. ~ indoorac-Wave2

    4. it does not come with a support contract.  You have to buy it separately.

    5. Yes, it is called trial and error.

  • Tecra A11 - 1F4 (PTSE0E-OM6052EN) which XP AHCI driver?

    I am trying to install the drivers for XP on a Tecra A11 AHCI;

    I have a ghost image that loads on this laptop in compatibility mode in the BIOS and I try to update the driver for the drive in AHCI controller, restart & change the disk to AHCI mode in the BIOS.

    That's what I usually do for HP laptops, we have, and it works most of the time.

    Storage power Toshiba drivers are in the form of an executable that will only work if you have AHCI enabled, how anyone runs in compatibility mode supposed to use these?
    They don't even extract driver files, you can use only the .cab files and an installer.

    I have listed in the device under IDE ATA/ATAPI controllers Manager;

    Intel (R) 5 Series/3400 Series Chipset Family 2 port Serial ATA Storage Controller - 3B2D
    Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - 3B 28
    Primary IDE channel
    Primary IDE channel
    Secondary IDE channel
    Secondary IDE channel
    3 entries for Peter card reader &

    Intel drivers, I downloaded from-

    s & OSFullname = Windows + XP + *.

    .. .and it gives me the list of controllers to choose;

    Intel (R) 5 Series 4 Port SATA AHCI Controller
    Intel (R) 5 Series 6 Port SATA AHCI Controller
    Intel (R) 5 Series/3400 Series SATA AHCI Controller
    Intel (R) 7 Series Chipsets SATA AHCI Controller
    Intel (R) 7 series/C216 Chipset Family SATA AHCI Controller
    Intel (R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller
    Intel(r) ICH10D / DO SATA AHCI Controller
    Intel(r) ICH10R SATA AHCI Controller
    Intel(r) ICH7M/MDH SATA AHCI Controller
    Intel(r) ICH9M - E / M SATA AHCI Controller
    Intel (R) Mobile Express Chipset SATA AHCI Controller

    The device ID of the controller (Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - B 3, 28), I'm trying to install the drivers AHCI is;
    PCI\VEN_8086 & DEV_3B28 & SUBSYS_00011179 & REV_06\3 & 115 83659 & 0 & FA

    Please can someone tell me which of these to use with the above material?

    It takes me ages to build, install, bluescreen & rebuild to try again...

    Thanks for sharing!

  • SATA drivers to install XP Pro on HP630 via diskette (F6 at startup)

    I have a laptop HP630 with SUSE OS installed. I want to install XP Pro but I don't know where to find the SATA drivers for installation via floppy with the F6 key at the start of the Installation of XP. Where can I find them?


    Ciao, Renato:

    You can get them at the link below: XP 32 bit is the second listed download. & ProdId = 2991 & DwnldID = 20625 & ProductFamily = Chipsets & ProductLine = Chipsets + Laptop & ProductProduct = Mobile+ Intel % c2% ae + 4 + Series + Express + Chipset + Family & lang = eng

    When you are prompted to install the driver, use your up/down arrow and scroll to select and install the Intel (r) Mobile Express Chipset SATA AHCI Controller.


  • Satellite L300 - no vertex shader and material & t on XP


    I have my Satellite L300 - 11G 1 year and now I keep getting screens well blue of death (BSOD). I thought that his problem of RAM, and I used the memory diagnostic tools and no problem with the RAM.

    I try to install another driver for Intel GM965 chipset, it gives me error saying "this material is not meet your system requirements" or something like that so I went to the website that is provided by intel [files\systemrequirementslab |], you can test the games that you can run on your computer, and there I was shocked! When I saw

    Required that you have
    Hardware T&L Yes No
    Vertex Shader version 3.0 0.0

    who's who? I thought that my graphics card does not support Vertex shader. I opened WINDOWS 7 with the same computer... Shocked again!
    Required that you have
    Hardware T&L Yes Yes
    Vertex Shader version 3.0 4.0

    Windows 7 my pixel shader and vertex shader = 4.0, Hardawre T & L = Yes
    Under windows XP my pixel shader = 3.0, shader vertex = 0.0 and hardware T & L = NO
    I NEED solution here is my description of the computer: -.

    RAM DDR2 2 GB
    VGA card mobile express chipset intel GM965 256 up to 358
    Bicoeur T2370 1.73 GHz processor

    How do on XP as if was on Win 7

    Hey Buddy,

    First of all, you can t have Pixel and Vertex shader 4.0 on XP! Windows XP supports only to competition only on DirectX 10 and DirectX 9 .0c or more possible to use shader 4.0 s and therefore you need Vista or Windows 7!
    So I think everything is ok and don t forget you don t have a high-end gaming laptop. That's why you should buy a new one, a Qosmio series for example.

    > I try to install another driver for Intel GM965 chipset, it gives me error saying "this material is not meet your system requirements.
    I had the same problem and the solution was simple: just install manual chipset driver through the Device Manager where you can choose the driver directory (Advanced installation).
    Check it!

  • AHCI for Windows professional XP on Elitebook 2560p drivers

    Due to a specific part of the software, I'm trying to install Windows XP on an EliteBook 2560p with drivers for the SATA AHCI controller.  Where can I get these drivers, and what is the best way to install?  I guess that since the laptop doesn't have a floppy drive I need to incorporate them into my XP CD?  What is the specific chipset driver? -from what I've seen on the page from Intel, there are a bunch of different options; ICH10d, ICH10R, ICH7M, etc, etc.

    Thanks in advance.

    TSK, tsk.  You must have obtained the name of the first ACHI SATA controller.

    This is the reason why we should always have a USB FDD in their Toolkit.

    Ok. I'll take a guess and say that you have the Intel (r) Mobile Express Chipset SATA AHCI Controller.

    Now that you have already installed XP, first install the chipset driver and restart.

    Download the second listed file and then extract these drivers to a folder that you put somewhere on your drive C:\ so that you can navigate him later. * & DownloadType=.

    Follow this procedure to install the AHCI with XP driver:

    1. right click on the icon my computer, click on manage, select Device Manager

    2. click on the + sign next to IDE ATA/ATAPI controllers, it would show the devices under this category.

    3. you will find the listed Intel SATA AHCI storage controller.

    4. right click on the Intel® 6 Series/C200 Series Chipset Family 4 port Serial ATA Storage Controller - 1 01
    listed, then click on set to update driver.

    5. in the Welcome to the Hardware Update Wizard, select No, not this time. Click Next.

    6. Select install from a list or specific location (Advanced). Click next

    7. Select don't search, I will choose the driver to install. Click next

    8. click on Have Disk

    9. click on browse

    10. Select the location: c:\folder you saved the Intel AHCI drivers.

    11 choose iaAHCI.inf

    12. click on open

    13 lists several SATA AHCI controllers. In this list, select the Intel(r) Mobile Express Chipset SATA AHCI Controller. Click Next.

    14. the update driver warning will be displayed. Click Yes

    15. the driver will be installed, and as soon as the update Hardware Wizard appears. Click on finish

    16. you can find the update controller in Device Manager.

    17 while the reboot, press the F10 key and start the BIOS configuration utility. Return to your submenu device configurations and change the setting of SATA to ACHI, save the settings there (F10) and their output, save the changes and restart.

    Now, the SATA driver is correctly installed and the Bureau will start in Windows, with device SATA AHCI Mode value.


Maybe you are looking for