Airport Express has stopped working after a reboot?

Similar Questions

• Airport Express has stopped working

  I've had my Express for about 8 years now and it has continued to become slower and slower for a wireless internet connection. I tested the speed with a speed test wireless online and on-line decision-making. Direct I get around 50MBPS and through the Express, I received only around 10 Mbps. I did this test a few days ago! Yesterday my Mac couldn't even recognize it even if the light on the Express was green. It of time for a new wireless router, or is there something I can do to solve the problem?

  Older versions of the AirPort Express had a useful life expectancy, on average, about 3-4 years.  5 years of use was much better than the average, so if you're 8 years old, you should Pat yourself on the back for your very good luck and reward yourself with a new router.

  If you want to keep the old Express, so about all you can do is reset to default values and then put in place again to see if that would help the Express perform a little longer.

  If you run an operating system recent on your MacBook Pro, like Lion, Lion mountain, Mavericks, Yosemite, etc., it is possible that AirPort on your Mac utility is even more supports the version of the Express you may have. To see if this could be a problem...

  Check to locate the model number on the side of the AirPort Express Terminal. It is difficult to see, so you need to perhaps good lighting and reading glasses. The model number starts with an 'A' follow-up of four digits.  Post back with that info

  To check what operating system you use on your Mac...

  Click on the Apple icon in the upper left corner of the screen, then click on about this Mac and post back with the Version of OS X number that you see there.

• on dv6 fingerprint reader has stopped working after installing Norton 2012

  Fingerprint reader has stopped working after installing Norton Internet Security 2012 on both of my notebooks from HP.

  Product name: HP Pavilion dv6

  Operating system: Windows 7 64-bit

  Error message in Device Manager under biometric devices in Device Manager displays an exclamation mark beside validity sensors (WBF) (PID = 0018). The following message is under the general tab: "Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19) ».

  Driver is present and seems to be up-to-date.

  Appreciate your help.

  I have finally isolated the problem of my software lack of HP dv6 fingerprint reader. I think Norton Removal Tool, available online at www.symentec.com/nrt, was the reason. I am sure this conclusion because the exact same problem occurred after I installed Norton Internet Security 2012 on laptop HP same as my wife. I tried, in vain, to uninstall and reinstall the driver for the biometric fingerprint device provided by Validity Sensors, Inc.

  After spending a day and a half to try to "solve" the problem, I decided to restore my system and go back to the prior agreement of the point of the installation of Norton. Thank you HP to make this process quick and painless. Don't forget that if you installed anything after the restore point, it will have to be reinstalled.

  Fortunately, there's a less intrusive on CD of Norton removal tool. This utility uninstalls an older version of Norton you are requested to restart and then installs the latest NIS. It is a method of removal safer that wide brush offered by the Norton Online link, which wipes everything remotely suspect.

  After reinstalling Norton Internet Security 2012 from the CD, everything works as it should, including the fingerprint reader.

• G72-a20EM screen has stopped working after updating the BIOS F.48.

  How is it possible that BIOS update recommended could turn off the LCD screen.

  Currently I see almost anything on the screen, but vga port works. But increasingly,.

  Intel graphics card is not recognized.

  G72-a20EM screen has stopped working after updating the BIOS F.48.

  What can I do to fix that?

  Good news!

  I found the working version, and it is version F.08.

  Supposedly new version have different Active cables, and this is the reason why the screen is dark.

  So, case closed, everything is perfect.

• My illustrator CS3 has stopped working after I updated my OS to Yosemite 10.10.5

  My illustrator CS3 has stopped working after I updated my OS to Yosemite 10.10.5, but my InDesign and Photoshop work very well. How can I get Illustrator to start working again?

  NOTE: I read a previous thread on the opening of the Java Control Panel in the system preferences (because I installed the new java my computer asked me for marketing immediately after in the new yosemite), but there is no icon Java not found. I installed this new java download more than once and still can not find it. Help!

  olou,

  If the suggestion on possible recording by Larry fails, see this page

  https://www.Adobe.com/account/my-products-services.html

  I'll try to ask a personal forum friend who knows what to do.

  For download, read this

  http://helpx.Adobe.com/Creative-Suite/KB/CS3-product-downloads.html

  and update, see

  http://www.Adobe.com/support/downloads/product.jsp?product=27&platform=Windows

  http://www.Adobe.com/support/downloads/product.jsp?product=27&platform=Macintosh

• "First Pro CC 2014.2 has stopped working" after a few moments of running and usually after you import a video clip.

  "First Pro CC 2014.2 has stopped working" after a few moments of running and usually after you import a video clip.

  I use a Lenovo T440p with Intel Core i5 @2 laptopp. 60 GHz, 8 GB of RAM. Windows 7 64-bit with Service Pack 1. Intel HD 4600 graphics card. All the drivers are up to date.

  All other non - CC Adobe video editing programs work.

  Help, please. Thank you.

  Dennis,

  Changing the video rendering engine should have solved the problem. Is it still pending?

  Thank you

  Regalo

• GfxUI.exe has stopped working after rebooting the computer.

  Original title: error GfxUI.exe

  I've been running Vista business for a few years.  Last week, after the reboot, I get an error message that GfxUI.exe has stopped working.  After that I closed the error box, the PC works fine.  I updated the graphic driver Intel, but always the message.  Why now I get the message and how can I solve this problem?

  Hi Kea2300,

  Did you the latest changes on the system?

  This error message indicates to the Intel graphics driver.

  Because you tried to update the Intel graphics card, you can try to perform a clean boot and check if the problem persists.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  After the troubleshooting steps, please refer to clean the boot link to put the computer to normal startup mode.

  Hope this information is useful.

• I get the message "firefox has stopped working" after closing browser

  Hello.

  My problem is that when I close the FireFox browser, I get the message "FireFox has stopped working". It's pretty boring. I have read some other posts here that describes a similar problem and we tried some of the suggestions in them including:

  A clean install, a reset of the browser, running in safe mode, uncheck hardware acceleration, disabling Extensions and plugins one at a time, uninstall my antivirus (avast), backward to 23.01 and audit version run in compatibility mode that someone claims to be helped. None of this has been effective.

  It seems that after a reboot of the computer, the browser will be ok for 2-4 closures and then it will start by the message at each end. In addition, after uninstalling avast was good for 6 closures. Roll back also gave me approximately 6 free message closures. But then, the messages and does not stop.

  Is there anything else I can try? Thanks in advance for your suggestions.

  
  

• Satellite U300-130 - TosBtMng has stopped working after installing Nokia PC Suite

  I have the same problem too... with Toshiba Satellite U300-130.

  Bluetooth worked well enough before I installed the Nokia PC Suite for my mobile on my PC (new version 7.1.26.0 Web site).

  To be correct, as a first step, I even managed to maintain a connection between the PC and the Nokia Bluetooth and ran the synchronization of the contacts. I tried several times, but each time synchronization run ended with the message "PC couldn't get response from your Nokia.

  After the reboot, my PC went crazy and started broadcasting the message "TosBtMng has stopped working" and it restarted every time that I ask him to close.

  Installation of the new version of BT Stack (6.40) does not resolve this error.

  Help, please

  I also use Toshiba Satellite, I use this [suite Nokia pc | http://www.softsea.com/review/Nokia-PC-Suite.html] version

• Receive the error "Windows has stopped working" after installing the update of security for Vista (KB977165)

  I use Vista Business, I installed the update of important security for Vista (KB977165), after installing and restarting my computer, I received an error message that Windows has stopped working and then I get a black screen. I rebooted in safe mode and did a system restored. So currently I did not update.

  This happened to someone else? Is it I can do it fix it?

  Hello

  Since you get such a serious mistake, I would use the free incident reports.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Outlook 2010 has stopped working after Windows updates

  November 11, 2015, my desktop, operating system Windows 7, installed about 28 updates to Windows. When I then put running the computer and open Microsoft Outlook 2010, Outlook closed almost immediately and this message appeared: "Microsoft Outlook has stopped working. A problem caused the blocking of the program works correctly. Windows will close the program and notify you if a solution is available. "(I don't check other office software).

  After the problem with Outlook 2010, I rebooted the computer several times and each time has experienced the same problem with Outlook 2010.

  I used system restore to restore the system to before the updates of Windows, which included a critical update. Outlook, then worked correctly. I changed the settings for Windows Update to "Never check updates" so that Outlook is not yet damaged.

  Was it something wrong with the Windows updates?

  The problem was solved when Microsoft released a revised version of the KB3097877 update. Maxwell Joseph, moderator of the Forum Microsoft, announced this in the post, he created at 23:22:03 on November 12, 2015, on the thread titled "update KB3097877 crash.

  He said ' Microsoft has released a revised update, so we suggest you go ahead and uninstall Windows updates KB3097877 > installed updates. Restart the system and run the updates check and reinstall it back. »

• Fingerprint reader has stopped working after update vV1.0.3.49

  I recently downloaded from Toshiba and installed Fingerprint Utility V1.0.3.49 (tc00407400c.exe) and since my fingerprint reader has stopped working.
  The software opens but usually recognizes my fingerprints and can not connect any other way.

  Have uninstalled and reinstalled several times and same result.

  Device Manager says device works ok.

  May I ask what model phone you have and what system do you use?

  Probably, you need to delete stored fingerprints and after restarting again, you should try to register new fingerprints using the software update of fingerprints.

  Have you tried that?

• Adapter Ethernet Thunderbolt has stopped working after update 10.11.2.

  Hello, after my update to 10.11.2 on my MacBook Pro retina 15 "mid-2015, my crush Ethernet Adapter has stopped working. It comes in the reporting system and it shows that it connected to ethernet, but in the network Panel, the State remains red and I don't get an IP address.

  My colleague who has a MacBook 2013 15 "retina Pro also has the same problem. We tried the retail adapters Ethernet Thunderbolt, but still no connection on one of our networks.

  Anyone else see this behavior?

  Same problem here on my end 2013. In Recovery Mode, the card works (good trick to know if hardware is broken). Roll back via Time Machine works 10.11.1 and adapter. Adapter and 10.11.2 relocation does not-MBP-R all my colleagues in different years work well after the update.

  BTW. : not only Thunderbolt Ethernet does not work, but the cards virtual Parallels (for shared and host-only) as well (only bridged mode works).

  So far, all the stuff has failed. And now I will notify again before the update.

• Desktop Window Manager has stopped working after loading of updates 12/10/10 MS

  Once the download and installation of updates for Windows 12/10/10 patches, Desktop Window Manager has stopped working.  Event viewer lists under Applications:

  Name: Application
  Source: Application error
  Date: 2010-10-13 09:59:47
  Event ID: 1000
  Task category: (100)
  Level: error
  Keywords: Classic
  User: n/a
  Computer: has
  Description:
  The failing application name: Dwm.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc541
  The failed module name: nvwgf2umx.dll, version: 8.17.12.5922, time stamp: 0x4c5424d5
  Exception code: 0xc0000005
  Offset: 0x000000000007c160
  ID of the process failed: 0xb0c
  Start time of application vulnerabilities: 0x01cb6aefa117a51c
  The failing application path: C:\Windows\system32\Dwm.exe
  Path of the failing module: C:\Windows\system32\nvwgf2umx.dll
  Report ID: e6dfd048-d6e2-11df-9660-00271383b7fe

  The operating system is Win 7 x 64.  Video card is a Gigabyte GTS450OC1 with its latest driver running on an Intel DP55KG MB with 8 GB memory Corsair XMS3.  The system was fully functional and stable immediately before the update.  I don't know which of the 18 patches is in conflict with the nvwgf2umx.dll file.  Device Manager reports no hardware problem with any component.

  In my attempts to solve the problem, I run chkdsk f, sfc/scannow (which have reported no problem) and reloaded the video driver (without uninstall first).   Nothing works so far.  I even tried to defragment the master file with Diskeeper 2010 start time Table Defragger (based on another post, I've found), also without success.

  What is the reference for this?

  This may seem like the thing the more janky to post, but I got the same error several months:

  Problem event name: APPCRASH

  Application name: Dwm.exe

  Application version: 6.1.7600.16385

  Application timestamp: 4a5bc541

  Fault Module name: nvwgf2umx.dll

  Fault Module Version: 9.18.13.1422

  Timestamp of Module error: 51427a 68

  Exception code: c0000005

  Exception offset: 000000000013fe0b

  OS version: 6.1.7601.2.1.0.256.1

  Locale ID: 1033

  Additional information 1: bd9d

  More information 2: bd9dfb84ef7bbf0c089fd3d5f079469b

  Additional information 3: ec39

  Additional information 4: ec39233315f018bea3fd5d4de7e9458f
  And could not cancel the record/re-record the dll it error out on an entry point missing or whatever.
  So what for some reason any worked for me is to rename C:\Windows\System32\nvwgf2umx.dll to nvwgf2umx.dll.bak (all other copies of this file are in the folder DriverStore).
  After that, I ran from an administrator command prompt
  net stop uxsms
  net start uxsms
  
  
  And miraculously all started working again.  I'm running a GTX570 with latest drivers nvidia from Scripture.
  Note: You probably shouldn't be move/rename things in System32 unless you are confident and have your data backed up.  It worked for me, but who knows you.

• Windows Explorer has stopped working after I did a registry clean with C-Cleaner?

  Hi im using windows7 32 bit and I have been using my normal pc then C-Cleaner, I opened and I clicked on reg clean, but I didn't return so I tried to open the partition (D) stands at its opening do not and I get this message "Windows Explorer has stoped working.

  Note: All other partitions works very well & I also made an error checking

  Hello

  I suggest you to see link and check.

  Error: Windows Explorer has stopped working

  http://support.Microsoft.com/kb/2694911

  Note: After checking in the clean boot, follow step: 7 article to reset your computer to normal startup.

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  Important: During the scan of the hard drive if bad sectors are found, the scanner tries to repair this sector, all available on which data may be lost.