Airport link to new modem

Similar Questions

• How to reset AirPort Extreme 10.11.6 OS? How to work with this pinhole? I'm trying to get rid of this flashing yellow light, which began after I installed a new modem from Comcast.

  How to reset AirPort Extreme 10.11.6 OS? How to work with this pinhole? I'm trying to get rid of this flashing yellow light, which began after I installed a new modem from Comcast.

  How to work with this pinhole?

  Usually a paperclip or toothpick or ball pen.

  Stick it in the hole and reset for about 10 seconds until the front led flashes quickly.

  How to reset AirPort Extreme 10.11.6 OS?

  The software method... Unlike the above material method... is to open airport utility and select restore default settings.

  

  Both methods take you to the same place.

  You can also read the manual...

  Reset to a base station AirPort FAQ - Apple Support

• I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

  Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

  Turn off the new modem for at least 30 minutes. More is better.

  Perform a hard reset on the AirPort Extreme, then it turned off.

  Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

  After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

  Then, turn on the airport and let it run a few minutes

  Set up AirPort Extreme again

  Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

• I have a new modem and you want to configure my Apple Airport as a backup drive; How do I do that?

  I have a new modem from Verizon and want to configure my Apple Airport as a backup drive; How do I do that?  I need to extend the network, simply find a use for the airport.

  What is the brand and model of your new modem from Verizon? What is the exact model of your airport?

• Xfinity triple play requires new modem?

  I have a Motorola model surfboard SB6120 I bought to use with the airport. Now I upgraded to Triple Play and Comcast told me I need a new modem or the service will not work. Is this correct? I assumed that if I buy the ARIS they recommend so I no longer need Airport?
  I read the reviews of the modem that it was difficult to set up etc and don't want to buy a new modem, if I don't have to do.

  I know just enough to know that I don't know about all that stuff. So in your reply, would you mind ' dumbing down there? " Thank you!

  Susan

  Comcast told me I need a new modem or the service will not work. Is this correct?

  That would be a question of Comcast with Apple support.

  I assumed that if I buy the ARIS they recommend so I no longer need Airport?

  What model number of the Arris product they recommend?  (Arris offers more than a dozen different products)

  If you get a 'simple' modem, as the SB6120 you have now with only a single Ethernet port at the back of the unit, then you will always need airport to act as a router.

  If they recommend a type of device that combines a separate modem and a router separate in the same package, then you are probably the most convenient airport... but you can still use it if you want to "modem/router" or "gateway".

  You have two wireless in this way, you may not need.  Some users use a network to their 'private' network and then use another wireless for the 'guests'... so it does not give the password to your private network.

• The most convenient airport and Arris CM820 modem drop connection

  I have Airport Extreme 6 Gen and a few months back from a 'new' Arris CM820 Time Warner Cable modem. Since then, I did have slowly and dropped connection problems a day - mostly in the evening so that streaming on Apple TV and Roku, and navigation devices on the MacBook Air and iPads at the same time. Each time, I do unplug it, wait 30 seconds and plug back in and it's good for a while. But it happens almost every day. I have been emailing and talking by phone with a representative from Apple support for a few weeks (had a record of the case), then she disappeared on me. I've updated firmware (v 7.7.7). Have also tried using a 5 G network as an alternative - but there is no help. Anyone else having these issues with the 'new' modems THAT TWC sends?

  If you have already tested the modem, try to choose a time when you can turn off the AirPort router and connect your Mac directly to the modem for a day or two to try things like that.

  Alternatively, you can of course call TWC support and have them check the line and the modem, but you already know that they will say that "things seem good to here" and that "the problem must be another device, like your router. .. even though things worked very well before receiving the 'new' modem.

  If the MacBook Air listed in your slogan is the only Mac you have, then you will need a lightning Apple Ethernet adapter to perform this test.   Maid in Gigabit Ethernet Adapter - Apple

  If connection problems continue when you have the Mac connected directly to the modem, the modem would then become a strong suspect.  This is possible.  But, it is also possible that the connection remains stable throughout your test... and if it's the result, TWC has strong arguments to say that their service and the modem are working well.

  Until then, you really don't know if you have a modem problem, a problem of the airport, or as can sometimes be the case... a modem - router compatibility issue. In such cases, the modem out OK and airport does as well, and each manufacturer blames the other for the problem.

  Please post on your 'test' results in the next few days.

• Airport Extreme and Broadband Modem/Router

  I have my Airport Extreme (5th generation) plugged into a Broadband Modem/Router combo. I would like to have both able to use their wireless capabilities. The Airport Extreme has been previously connected to a Modem broadband all my IP addresses came by Airport Extreme (192.168.2. *). With the New Modem/Router combo broadband, it uses 10.0.0 * so I would be able to use Airport Extreme to add the 192.168.2. * While having the 10.0.0. * the Broadband Modem/Router combo.

  Is this possible and, if so, how do I configure Airport Extreme to do?

  Normally, you don't want two devices on the same network as the two try to act as routers to the same network. Which will produce conflicts of IP addresses... which can possibly be addressed... and a Double NAT problem, which cannot.

  The Double NAT error can cause a number of unpredictable issues... things like the problems of communication between the devices on the network, slow navigation... or, not navigation in the case of certain websites, Internet access slower, to name a few.

  Yes, some users may get away with a Double NAT on a single home network, but unnecessarily complicating things over a network is normally something you want to avoid.

  We do not recommend it, but if you really want AirPort Extreme for use range 192.168.2.x however, you can easily make this change using AirPort Utility. If you are not sure how to do this and need help, then we will need to know which version of AirPort utility you are using.

  To find, open AirPort Utility, and then click the menu of AirPort Utility in the far left of the screen corner. Click on about AirPort Utility to see what version you have and post back with that info.

• How can I configure my router to a new modem?

  I changed my internet provider and I have a new modem. How can I configure my router to work with my modem?

  Hi @Belem,

  You can check out the link below and see if it helps.

  http://KB.NETGEAR.com/app/answers/detail/A_ID/22697

  Kind regards

  Dexter

  The community team

• New Modem - like get a new modem my printer does not work

  Since obtaining a new modem, my printer does not work. The printer is a HP 4500 wireless all-in-one. What should I do?

  Hi reillydebra,

  1. you have made no changes to the computer before the broadcast took place?
  2. do you get an error message?
  3. what operating system do you use?

  If you use Windows 7, try the steps from the following link:

  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Why can I not print?
  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

  Additional information:
  Check if you need to open ports in the modem.
  http://h20563.www2.HP.com/p/_wireless/troubleshooting.html
  http://h10025.www1.HP.com/ewfrf/wc/documentSubCategory?tmp_rule=59455&tmp_task=solveCategory&cc=us&DLC=en&lang=en&LC=en&product=3919449

• Install new modem, now that half of my favorites appear

  Original title: Favorites

  Had to install a new Modem and now only half of my "Favorites" appear.  How to recover the rest of the list?

  not sure why a modem is responsible, unless you are short of memory ram.

   

  in all cases, you should be able to find here: C:\Documents and Settings\ {username}-Favorites

   

  You can click on the links directly or you can try to reinstall your browser.

   

  
  --
  db·´¯`·...¸><)))º>

  .

  "bstader" wrote in message news: 081 7805-fe22-44da-9694-eaa530beefb6 c...

  Had to install a new Modem and now only half of my "Favorites" appear.  How to recover the rest of the list?

  DB·´¯'·.. ¸ >-))) º > ·´¯'·.. ¸ >-))) º > share nirvana mann

• How to re - configure a Linksys E1200 wireless router after that I got a new Modem

  I just got a new modem.  My E1200 Linksys wireless router no longer works.  Technical support said it should be redefined to work with the router.  How do I do that?  Thank you

  Hi, feibelal ! You don't need to have an active Internet connection on your Mac to be able to access the user interface of the router E1200. The steps in the link provided by Thaddeus_A should do your router works.

  Kind regards

  Ethel_10700

  Linksys technical support

• Problems with the new modem DSL and Linksys BEFSR41

  My Speedstream modem died and I had to buy a new modem.  At this time of year, it is difficult to find exactly what I wanted and I ended up buying a D-Link DSL - 2320-B.  I got the Linksys BEFSR41 (old version 1, I think) for years and it has always worked well.  I have problems to get an internet connection through the router.  With the modem connected directly to the network card, as now I have no connectivity problem.  I had to change the IP address on the Linksys BEFSR41 192.168.2.1, as the modem is 192.168.1.1, 192.168.0.1 as the old Speedstream.  I couldn't see a way to change the IP Address of the new D-Link.  I have my ICS TCP/IP set to auto obtain IP and DNS.  I was previously created for a fixed IP of * provided by the router.  Even with the setting on the router to "Obtain an IP address automatically", I can't to the internet with the router in the middle.

  Any help will be appreciated.

  Your modem is a combination of the modem and the router. The problem occurs when you try to connect another router behind this configuration and end up having 2 servers dhcp and nat 2 (for port forwarding and other issues, creating in some cases where even branded products use ip addresses will clash and devices will not connect at all when him are interconnected).

  To avoid the situation described above, it is recommended that you enable the full Bridge mode on the modem / router that you currently connected to the internet and let your new wireless router controls all the functions within your local network and the internet connection (you must enter all the details in the new router, including Internet service provider username and password).

• WAP54G and new modem

  I had wireless access WAP54G for about two years, connected to a D-Link router which is connected to a SpeedStream 5260 DSL modem, he supported a desk and four laptops without any problem. The modem is old and starting to have problems of hosting an internet connection. I bought a new Motorola 2210 modem today and configured via a wired connection with my office. When I connect it to the WAP54G I can access internet from my office, but laptops have a problem connecting to the access point. Reconnect the old modem and everything is back to normal, every PC can access the internet and the other. Someone at - it else experienced this type of problem?

  You must ensure that all the new modem settings match those of the old modem. IE, was the old modem in Bridge mode where the Internet IP address is hosted ob your router, or has the IP address of the modem. Are the parameters of gateway & DNS the same etc.

  The problem you are experiencing is not a function ot the WAP54G as this was never changed or modified.

  Concerning

  Fred

• Development in error "Installer.exe has stopped working" while installing the new modem.

  Development in error "Installer.exe has stopped working" while installing the new modem. I try to install the ZTE AC8710 modem on my 32-bit windows vista (home edition) system, but whenever the facility is subject to the full I get the error 'Installer.exe has stopped working' and complete Setup doen't. The same error is hit when I try to uninstall the ZTE modem that is installed intestinal. The installation file has CD/install drivers for windows vista. Information below is displayed in the application event viewer for this error log. Help, please

  Log name: Application

  Source: Application error

  Date: 2010-01-03 02:04:50

  Event ID: 1000

  Task category: (100)

  Level: error

  Keywords: Classic

  User: n/a

  Computer: Monica-PC

  Description:

  Application Installer.exe, version 0.0.0.0, time stamp 0x4b208462, Installer.exe module, version 0.0.0.0, time stamp 0x4b208462, exception code 0 x 40000015, offset error 0x0002efec, 0xadc process id, failed failed application start 0x01cab8b5797299e1.

  The event XML:

  1000

  2

  100

  0 x 80000000000000

  309

  Application

  Monica-PC

  Installer.exe

  0.0.0.0

  4b 208462

  Installer.exe

  0.0.0.0

  4b 208462

  40000015

  0002efec

  ADC

  01cab8b5797299e1

  Hi Tonio saini,.

  Navigate to the location of the programs .exe file and right click on the .exe file, and then select run as administrator to install the modem.

  You can also check the following link, try the suggestions and check if that helps:

  http://social.answers.Microsoft.com/forums/en/w7hardware/thread/4ce21286-3a77-4A06-923c-889d657f8e33

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot connect remotely via VPN since installing the new modem/router

  Can anyone help please. Since the acquisition of a new router / modem I can no longer connect via VPN to my work PC remotely. It comes in I receive the error message. Can someone tell me if I need to change the settings for the new modem / router to access?

  

  Hello Joanna,

  Here are the steps you need to do first:

  1. Off static IP for my server and let the router assign IP address and changed the IP address of the port forward.
  2. Check the IP address because obviously, that changed when you plugged into the router again.
  3. Updated to the latest firmware for the router and NIC.

  For more detailed troubleshooting you can refer to this link: troubleshooting common VPN related errors.

  Let us know how it goes.