All disks are not (but OK after power cycle). 5.3.12 T3

Hello

I have a ReadyNAS NV + v2 with 4x2GB HDD.

He was fine on 5.3.12 T3, but twice in the last week, I noticed the morning (he auto-fermetures to 02:00) on the screen LCD allows you to select the message saying disks 1-4 have failed.

I have to unplug/Plug and it challenges very well.

Newspapers by e-mail

Thank you

Andy

Thanks for the newspapers.

Your disks are in need of a firmware update.

First back up your data.

Then update the firmware on your drives firmware CC3D.

Tags: Netgear

Similar Questions

  • CD-Rom indicated that all disks are not formatted.

    All of a sudden (no major changes to the system) the CD-Rom on my laptop started to say all CDs (burned and commercial) are not formatted and that Windows is unable to read the disc. I reinstalled the drivers and windows updates, but the problem is still there. Thoughts?

    1 swap hunt for a well-known work. OR
    2. put the drive in another computer. OR
    3. start with a bootable CD as the disc to install XP or a Linux Live disc and see what happens. If the drive cannot read a bootable CD (and this will happen outside Windows), then you will know for sure it is a defective material. MS - MVP - Elephant Boy computers - don't panic!

  • I signed on XP Pro SP3 as an administrator but you cannot change the timing of Windows Update to 03:00. All options are not enabled. How can I change the time, updates are made? __

    I signed on XP Pro SP3 as an administrator but you cannot change the timing of Windows Update to 03:00.  All options are not enabled.  How can I change the time that updates are made?

    Hi imoffshore,

     

    Welcome to Microsoft Answers Forums.

    We would like to get some more information from you to help solve your problem. You better, please answer the following questions.

    ·         When was the last time it worked?

    ·         Remember to make changes to the computer recently?

    ·         You have security software installed on the computer?

    ·         You get the error message?

    When you open the tab automatic updates in the control panel or My Computer property sheet, all options of configuration of the automatic updates may be grayed out. This happens due to one of the following reasons:

    1. You are not logged as administrator (or equivalent)
    2. Strategy of automatic updates is enabled
    3. Automatic updates (and Windows Update) access is blocked by group policy

    The options available for automatic updates.

    You must make some changes in the windows registry.

    Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

    How to back up and restore the registry in Windows

    http://support.Microsoft.com/kb/322756

    • Click Start, run and type REGEDIT to . EXE
    • Go to this location:

    HKEY_LOCAL_MACHINE-SOFTWARE-policies-Microsoft-Windows------WindowsUpdate------AU

    • In the right pane, delete the two values AUOptions and NoAutoUpdate
    • Go to this location:

    HKEY_CURRENT_USER-SOFTWARE-Microsoft-Windows-CurrentVersion------policies------WindowsUpdate

    • In the right pane, delete the DisableWindowsUpdateAccess value

    Using the Group Policy Editor - for Windows XP Professional

    • Click Start, run and type gpedit.msc
    • Navigate to the following location:

    => Configuration of the computer
    ==> Administrative templates
    ===> Windows components
    ===> Windows Update

    • In the right pane, double-click Configure automatic updates and set it to not configured
    • Next, go to this location:

    => User configuration
    ==> Administrative templates
    ===> Windows components
    ===> Windows Update

    • In the right pane, set to remove access to all Windows Update features on not configured

    Change how Windows installs or notifies you of updates

    http://Windows.Microsoft.com/en-us/Windows-Vista/change-how-Windows-installs-or-notifies-you-about-updates

    Halima S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • I want to download all versions are necessary, but I can not understand what are the dated versions are currently installed in my PC?

    Re: "drivers and downloads" my computer dell laptop inspiron I6400 / E 1505; Windows vista Home premium, 32 bit OS: I want to download all versions are necessary, but I can not understand what are the dated versions are currently installed in my PC?

    Hello

    I suggest you try the given below steps that would help you to view the details of the driver.

    (a) type devmgmt.msc into the search box start and press enter.

    (b) in the Device Manager, right click on the device you need to display the version.

    (c) select Properties.

    (d) click the driver tab and display the version of the driver in the Driver Details.

    Hope this information is useful.

  • After importation, all 'frames' are present, but the picture is blank (gray).

    After importation, all 'frames' are present, but the picture is blank (gray). When I tried to edit in Photoshop CC, it opens correctly. Tried to delete CC with cleaning tool. Re-installed with the same question. Repeated twice with the same consistent result.

    Photos opening are exported during the migration process and opens in Preview/Photoshop. Tried with a variety of photos with the same result as well.

    Screen Shot 2015-10-17 at 6.20.32 AM.png

    MacOS X 10.11 (iMac end of 2014)

    CC 2015 Lightroom and Photoshop CC 2015.

    Hi clementl55784534,

    Suggest you follow the steps below:

    1. Turn off apply tone auto under Lightroom preferences settings
    2. Restart Lightroom and then import images again.
  • Error "the dynamic disks are not supported by this operating system." what configuration Raid 0 (striped) readers.

    I have my operating system installed on a single disc, and I bought two additional discs I want to implement in a Raid 0 configuration. I'm going to administrative tools > computer management > disk management > right-click on a single disc and select the new striped volume > add the second drive and fill the dialog box until I get to the part where the formatting is supposed to start. Then I am stopped by an error that says "the dynamic disks are not supported on this operating system."

    Who says that hard drives, I bought are not compatible with vista interlacing or it says that vista can not the striped disks. What is the problem?

    You need to configure raid 0 before installation of win, you cannot "convert" s simple drive to the part of a matrix of blocks.

    In general this is not a good idea to use software raid, too a overload the CPU. If you want to raid, invest in a dedicated hardware raid card, which for a decent cost probably more than your motherboard

  • Cannot convert a computer unalloacted on a new space, dynamic disks are not supported by this operating system or the configuration of the server. Dynamic disks are not supported on Clusters.

    I have 179 GB of a 50 GB hard disk on a new computer allowed. Try to make a new Simple Volume I get following error "the dynamic disks are not supported by this operating system or the configuration of the server. Dynamic disks are not supported on Clusters", please suggest what to do, i run Windows 7 Home basic.

    I have 179 GB of a 50 GB hard disk on a new computer allowed. Try to make a new Simple Volume I get following error "the dynamic disks are not supported by this operating system or the configuration of the server. Dynamic disks are not supported on Clusters", please suggest what to do, i run Windows 7 Home basic.

    Need additional details as
    Is it a laptop or a pc?
    Have you coveted your dynamic disk basic disk?
    What the structure of partition on your computer?

    recover with these details...

  • problem installing drivers for WinTV-PVR-150/500. rpet pilots are not digtally signed after installing drivers. HELP PLZ?

    rpet pilots are not digtally signed after installing drivers. HELP PLZ?

    See this

    http://www.SnapStream.com/download/hardware/PVR-500MCE-installation.asp

  • FATAL error after Power Cycle - GVRP associated?

    Hi all

    Happy new year!

    I have a network of four 300 switches of the series of small businesses. All are running the version of the 1.3.5.58 software (latest version).

    Three of them are connected by 2 groups of LAG to the central switch that in turn connects to the router facing the internet. There are no loops in the architecture and protocols spanning tree is running. There are a total of 4 VLANS and GVRP Protocol is enabled with the four VLANS created statically on the main switch.

    Normally, everything works very good and is perfectly stable.

    However, a power outage this morning resulted in a cycle of power on two of the switches. They did not recover gracefully and kept restarting.

    I removed the ports belonging to groups LAG in the main switch (not affected by the power cycle) and then rebuilt in order to recover the connectivity and restore normal operation.

    Both of the switches which restarted several entries in their logs like this: -.

    % GVRP-F-NOSTATREG: GVRPP_checkStaticToDynamic_update: Port is not declared statically on vlan 100 * FATAL ERROR * task Reporting: BRMN. Software version: 1.3.5.58 (date October 10, 2013 time 17:15:41) 0x16adbc 0x166f28 0x6df2b0 0x48fad8 0x4903e8 0 x 490608 0x51a234 0x79dfd8 0x7b9f8c 0x7c1500 0x445d 88 0x41e04c 0x7d4c80 0x61cb68 0x1223f0 * END OF FATAL ERROR *.

    Has any seen this before? I made a mistake of 'beginner' with GVRP configuration?

    Kind regards

    Andy.

    Hi Andrew, Yes, that sounds all right. Essentially every change made to the master advertising GVRP wide affects each vlan, not one of them. So I think that restarting the switch downstream which forces to join will update properly for the master join message.

    -Tom
    Please mark replied messages useful

  • All icons are shaded and wavy after installation of the patch and restart (win xp sp3). How can I fix it?

    After you have installed the latest patches, all icons are shaded with vertical lines undulate on them.  Computers desktop and in Windows Explorer.  Application windows appear clear, but icnos in their midst are the same way.  What should I do to fix this anomaly?

    -J' tried the obvious desktop refresh. No change.
    -J' rebooted in safe mode, and then back to standard mode. No change.

    What else can I try?

    Hi JimGoode,

    Unfortunately, the screenshots are not available in the post.

    Given that the question does not appear in safe mode, then it is possible that some third-party programs installed on the computer is causing the problem.

    I suggest that you put the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See the link below to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    (a) click Start, type msconfig in the search box and press ENTER.

    (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

    (c) under the general tab, click the Normal startup option, and then click OK.

    (d) when you are prompted to restart the computer, click on restart.

    If the previous step fails, then use SkyDrive download screenshots of icons.

    Use SkyDrive download collected files and after shot/screenshot.

    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65/

  • WAG300N: could not start correctly after power failure

    Hello

    After AC power interruption, I tried to turn on my router Linksys WAG300N, but he won't start properly. I will describe what it looks like and what I've tried:

    I push the power button / stop, all 4 Ethernet LED simultaneous light for about a second, (if there is LAN cable connected, one or more led lights permanently) and power the LED will blink twice at normal speed. After that, both voltage and wireless, led simultaneously for about 1-2 seconds, start power LED flashes quickly, after seconds wireless LED stop light, wireless flash LED again and stop two LEDs for lighting. Second later power LED flashes two times normal speed and the process begins again but without flashing of the LED Ethernet (loop).

    I tried to download the firmware using TFTP, but it does not work. Router did not respond to a ping. After many tests, I noticed that the only time where I can ping router is during normal those two blinks of the power led. I've got 11 times waiting and the response of 1 or 2<1ms, 11="" timeouts,="" 1="" -="" 2="" responses etc... (response="" waiting="" time="" for="" a="" ping="">

    I've tried a few ways to reset the router (based on this forum). It does not help, sometimes after the reset I power the router problems or flashing process stops after a few loops (only one Ethernet LED lightning or router turns off). At the end of a day all supports them to the previous behavior of closure with power LED and wireless LED blinking.

    In the end, I tried utility upgrade Sercomm 2.07 mentioned in this topic: http://forums.linksys.com/linksys/board/message?board.id=DSL&thread.id=52

    This software detects only router after reset, when the router is in unknown mode, Internet and power LED flashes alternately.

    Software detects the device as MAC address and visualize correctly the version of firmware loaded into memory. Looks like it works and flashing memory. While flashing memory, power LED, LED Internet and Ethernet LED flashing at the same time very fast. I tried all versions of firmware available, but it does not help, I still have the same behave after flash.

    I think it could be a problem with the bootloader, maybe that part of the memory is broken, but I did not how to fix it. I found information on the JTAG interface, but I don't know if it will work for router WAG300N and where I can find the appropriate file with bootloader.

    Maybe someone can help and give me the idea what should I / check. Theoretically, I should have left 1 year warranty, but I lost the proof of purchase required for the RMA process. I can't find the place in Poland where professionals can help me, so I think that should do it myself with your help

    I think that's the problem with the power adapter... You should try a different power of the specification of the same card...

  • disk are not not in diskpart on windows 8.1

    I have two drives WD 2.0 TB I wanted to implement in a RAID 1 array. When I installed Windows 8.1, she saw two discs and I installed on disk 0. But now that I want to use storage to configure the second drive as a mirror, it is not available in storage spaces or in diskpart. BIOS and Device Manager recognize correctly the two disks as there and functional.

    Any thoughts?

    Hello

    The problem you are experiencing requires support from our TechNet forums. Please post your query in the TechNet forums using the link below.

    http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w8itpro

    Hope this information helps.

  • RED. R3D files are not supported in After Effects?

    When I try to import R3D files seem to be disabled in all supported formats.

    Also when I create a composition in After Effects from Adobe Premiere, he seems to be offline.

    Whats Happening?

    Screen Shot 2016-04-03 at 14.00.33.png

    This bug is fixed in the update after effects CC 2015 (13.7.2): http://adobe.ly/1WaV0pP

    This only bug fixes Update corrections occurred after effects CC 2015 (13.7.1) on Mac OS x files: RED (.r3d) can still be imported and are not reported as missing in existing projects.

    This update is only for Mac OS X and is not available for Windows, because the bug with the RED files does not occur under Windows. The most recent update for After Effects on Windows is after effects CC 2015 (13.7.1).

  • My license complete creative suite tells me that my trial has expired and now all programs are not available for me. What is going on?

    After 3 years, my suite fully licensed creative returned unexpectedly to a trial. Today it tells me that my trial has expired, and now all of the programs are not available for me. What is going on?

    Trial opens at the launch

  • segaments of restoration are not get deleted after completion of transact

    Hi all


    I do 8i production support.during data archiving activities I m facing a problem restoring segaments. As we know after instruction to commit, it allows free space once all transactions get more, but here its not free space after long back too.

    Please suggest me what to do?

    don't we have any tool by which I can check and free up space? Another manual way?

    With manual undo management - that is to say using Rollback Segments - will Oracle NOT resize or reduce rollback segments automatically (unless you set an OPTIMUM size). This is the architecture.

    If "I do data archiving activities, so a lot of deletion going on in the database" is, surely, it would be too much effort to write scripts plus two or three to re-create the Rollback Segments (and RBS tablespace) - you can even manage 'windows' archiving to do if you don't really have the space to the tablespace RBS. I guess that the "check database" is not automatic and requires the DBA run scripts. How much more effort is to add a few scripts and steps for managing Rollback segments?

    In normal operation it has no reason to shrink/drop/recreate Rollback Segments - even where a batch can increase requirements RBS for 2 to 5 times daily batch. Leave RBS to the maximum size is the easiest and safest.

Maybe you are looking for