An application based on a PC with LabVIEW 7 can be installed on a MAC?

Similar Questions

• Hello friends, I have a license with terms of the photo with Photoshop and Lightroom applications installed on my iMac. Question: With this license can I install these applications also in my notebook? Using the same license.

  Hello friends, I have a license with terms of the photo with Photoshop and Lightroom applications installed on my iMac. Question: With this license can I install these applications also in my notebook? Using the same license.

  Yes, individual licenses, ranging up to allow two simultaneous, activations facilities.

  subscriptions allow mounting on an unlimited number of computers.  connection is limited to a maximum of two computers at a time.

• Toshiba satellite which is stuck in the installation of service Pack 1. I have service pack 2, can not fix with this cd, can I install service Pack 2 on it without loss of data or files?

  I have the laptop (Toshiba satellite) friend who's stuck in the installation of the service Pack 1.  I have service pack 2 and am wondering, since I can't fix with this cd, can I install service Pack 2 on it without loss of data or files?

  PC claims service pack1 cd with file asms

  When you use service pack 2 cd can not load product catalogues, it is fatal error, the Setup logs files should contain more information.

  Why not integrate Service Pack 2 and Service Pack 3 on her XP CD by following the instructions here (using another PC):

  http://en.community.Dell.com/support-forums/software-OS/w/microsoft_os/1443.aspx
  Copy all data on an external hard drive, do a clean install using the XP CD updated (preferably on the BIOs)
  Then, install the drivers from the system, then Microsoft Security Essentials, Windows 7 Firewall Control (XP free Version) and Malwarebytes' AntiMalware (free or Pro) or whatever you prefer security.
  Then copy the files over.
  This will probably lead to the best performance.

• I can't install Photoshop CS5 Mac because of the size of my HARD drive that is logged with Capitol and minor letters. Is there a way to get it installed?

  Hello

  I can't install Photoshop CS5 Mac because of the size of my HARD drive that is logged with Capitol and minor letters.

  Is there a way to get it installed?

  Thank you

  Andreas

  Error "No supported drives case-sensitive" or similar facility. Mac OS

• I wrote a small application in swift, how can I install on my mac?

  I tried to deploy an application that I wrote in Xcode swift on my Mac so I can't run Xcode to use the application

  Simply build your application and move the final product where you want.  You can right click on the product in the Xcode project Navigator to display it in the Finder, because it's usually buried in your ~/Library folder user.

• application for bing in windows laptop 8-How can I install beginning of bing app tp after uninstalling it by chance?

  Please let me know in windows 8, how do I reinstall the app to bing, after I uninstalled it by accident?

  Press the Windows key + F

  Type: bing

  Click on Store in the list on the right

  Click on Bing

  Then click on install

  

• Implement the json JWT with labview web token

  I need to implement of JWT authentication with labview, how can it be done?

  I'm not aware of an existing library of JWT for LabVIEW. You can see the site of JWT to the creation and analysis of JWT requires:

  JSON encoder / decoder

  base64 encode / decode

  and a signature / encryption method (commonly built HMACSHA256 depends on the Oracle application)

  JSON encoding and decoding is available for LabVIEW 2013: https://zone.ni.com/reference/en-XX/help/371361K-01/glang/flat_unflat_string/

  The other two are not available of NEITHER, but have implementations in the LabVIEW community:

  Base64:

  https://decibel.NI.com/content/docs/doc-5544

  https://decibel.NI.com/content/docs/doc-23233

  Signature:

  https://lavag.org/files/file/198-encryption/

  https://decibel.NI.com/content/docs/doc-22585

  If unfortunately JWT support is not provided by default, but all the necessary parts to the realization that he should be here.

• Application errors of the RT with the PXI-4461 with Labview real-time 9.0.1, DAQmx 9.0.2

  HI -.

  I recently converted a PXI time system real OS (PXI-1042 q chassis, controller PXI-8187, DAQ, PXI-4461, DAQ, PXI-6259). I can write and run DAQmx applications in real time with the 6259 very well. Whenever I try to write a labview RT app to use the 4461, however, it will fail. Note that I can use two cards through MAX I tried switching card slots, just in case it was a problem. Both cards worked with labview, the PXI chassis was before Windows.

  Attached are pictures of the screw base demo I built to show the problem. Since I was a mistake (-200758) if I started from the raw strings, I tried to create a MAX task and use it. The task, but he complained of a buffer is too small. I explicitly put the buffer to work around this problem and still get the same error (-200608). I've also attached a screenshot of the software currently on the Max MAX RT PXI system is version 4.6.2 btw. (I installed the most/all this from DS1 Dev Suite 2010 version).

  Please let me know if I hurt something installed, versions if 4461 just don't play nice with the new BT or RT software, or if something is wrong. Thank you.

  Kregg

  The first error you see is (details in the help-> error explain in LV)

• When users who are working with an Application based on SQL (accounting), application suddenly closes!

  When users working with an Application based on SQL (accounting), application closes without prompting.

  We have virtual server Hyper-v with SQL server 2008 sp1 - other departments report no problem just for accounting

  They can't really work...

  Thank you

  Hadad

  These MS Answers forums are intended for the home rather than the it professional user. I suggest therefore that repost you your question in the forums MS Technet here:

  http://social.technet.microsoft.com/Forums/en-us/categories/ .

  (I'm sorry, but I can't move this thread for you because the two forums are working on separate platforms)

• MsiError 1627 then install application created with labview 2009

  Hello

  I tried to install an application created with labview 2009, I have this fatal error ' MsiError 1627: 1: 2727 2: UsFile.

  Executable works fine while the installer does not work!

  UsFile is a Lvclass. I don't understand why I have this message.

  Thank you very much.

  Hi thanks for the reply,

  I don't delete the installation program. It has not been disabled or corrupted MSI.

  Problem is in the source file: ProgramFilesFolder was not also identical to my request. So I refreshed that (the folder UsFile appeared not in ProgramFilesFolde)

  Now it works!

  Thank you very much Bye

• NI 9148 with LabView module detection

  Hello

  I got the task of creating a deployable (compiled) software to a DAQ system with NI 9148 Ethernet RIO basket background and various modules. The user must have the ability to change the module type and the location of the different tests, so the application must detect (or the user specify) what modules are at what positions.

  I watched the blockset CRY, however this chassis is not supported and the lowest level blocks are protected. Is it possible to read the serial number of the modules connected to the 9148 OR position, type, and if all goes well?

  Thanks for any help!

  Hello Soonxaf,

  What are you helps as a controller-is this RT or Windows? Are you planning on the use of analysis of RIO or LabVIEW FPGA engine?

  If you plan use the analytical engine, so this should help you get started:

  Tutorial: Discovery, Configuration and programming access of the CompactRIO Scan Mode to IO with LabVIEW

  http://www.NI.com/white-paper/9351/en

  Kind regards

• Executable VI with Labview 2011

  Hello everyone, I'm doing an executable on LabVIEW 2011 SP1. I've never done before, but in my project, I go to tools-> Build Application (EXE) from VI... I check to make sure that all the Sub VI are in the Dependencies tab and I put the way I want the EXE to go, then I build it. Building compiles and I have good Run-Time Engine installed, but when I go to open the EXE file, I get a lot of mistakes because void VI could not be loaded. I checked these Sub VI that were not loaded and they are locked and password protected. Probably comes with LabVIEW, so they don't want to play us with anything. How can I get these included in the EXE and not return an error?

  Thank you.

  I deleted the Run-Time Engine and downloaded again, and I think it worked. Strange, but I accept it

• temperature measurement with labview on four location using NTC thermistor

  
  

  Hello
  My project is the measure of the temperature of a thermistor on-site 4 difference.
  The measures must be 0 for 100 * C.

  details.
  

  • For the sensor, I must use only NTC thermistor.
  • I have to do an application with Labview.
  • the application must give me the right measure in real time, and it should save the sample in a database.
  • This measure is taken max 20 feet form the pc.
  
  I'm new with this.
  Can someone help me with sensor circuits.
  How can use DAQ with the thermistor.
  Can I use EMANT300 Low-Cost USB DAQ Module 24 bit?

  Please give an idea

• Wonderware R6030 with Labview starting fault

  This could be more appropriate for a Wonderware forum, but here goes:

  We try to read the data from PLCs AB, by using the OPC and Labview.

  We can properly install the Labview application, but restarting and restarting of Wonderware, we get an error message:

  C.... Archestra\alarmmgr.exe R6030 CRT not initialized.

  Configuration:

  Windows XP

  Wonderware 10.0.200 (DAServer\DASABCIP)

  OPC Server

  OR VISA

  Anyone run into this error before?

  Thank you very much

  Ann

  Hello Ann,.

  I would recommend posting your question in this forum: http://forums.ni.com/t5/Industrial-Communications/bd-p/260 to get a better response from the teams that support the OPC servers and also check with Wonderware to see if they have seen this behavior before.

  Kind regards

• Cannot bind to the shared object created with LabVIEW 2009

  I have problems referring to a shared library built from a LabVIEW VI under RHEL 5 with LabVIEW 2009.

  To illustrate the problem, I created a VI with a digital input and output that corresponds to a certain number. Then, I created a draft specification of build to create a shared library with a feature that makes use of this VI square. The shared object is created successfully (square.so).

  When I try to compile a test application written in C, that connects to this library, I get errors in the following link:

  cc  -I/usr/local/natinst/nidaqmxbase/include -I/usr/local/natinst/LabVIEW-2009/cintools build/square.so  test.c   -o test/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(float&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(double&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(double&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_ostream >& std::basic_ostream >::_M_insert(double)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_istream >& std::basic_istream >::_M_extract(float&)@GLIBCXX_3.4.9'/usr/local/lib/liblvrtdark.so.9.0: undefined reference to `std::basic_ostream >& std::basic_ostream >::_M_insert(double)@GLIBCXX_3.4.9'collect2: ld returned 1 exit statusmake: *** [test] Error 1
  

  Running ldd reveals that liblvrtdark.so.9.0 is used for the execution of labview.

  In order to investigate on what could be the cause of the problem, I have compiled the nidaqmx basic examples, and I don't have an error. Current running ldd as reveals that he uses liblvrtdark.so.8.2 for the view of laboratory, time of execution.

  My suspicion is that some components of labview are being compiled with gcc 3.4 while others are being compiled with gcc 4.1 (which is the default compiler in RHEL 5).

  Any ideas how I could fix the build errors?

  Thanks in advance for your suggestions.

  PS.

  I enclose a tar file with the source files and here are the details of the ldd:

  ldd build/square.so         linux-gate.so.1 =>  (0x008de000)        liblvrtdark.so.9.0 => /usr/local/lib/liblvrtdark.so.9.0 (0x00b9c000)        libc.so.6 => /lib/libc.so.6 (0x00110000)        libstdc++.so.6 => /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 (0x009a7000)        libm.so.6 => /lib/libm.so.6 (0x00756000)        libdl.so.2 => /lib/libdl.so.2 (0x00256000)        libpthread.so.0 => /lib/libpthread.so.0 (0x0025a000)        /lib/ld-linux.so.2 (0x00b80000)        libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x00272000)
  
  ldd /usr/local/natinst/nidaqmxbase/lib/libnidaqmxbase.so.3.3.0         linux-gate.so.1 =>  (0x00e50000)        libnidaqmxbaselv.so => /usr/local/lib/libnidaqmxbaselv.so (0x00248000)        libc.so.6 => /lib/libc.so.6 (0x00689000)        /lib/ld-linux.so.2 (0x00b80000)        liblvrtdark.so.8.2 => /usr/local/lib/liblvrtdark.so.8.2 (0x00e51000)        libdl.so.2 => /lib/libdl.so.2 (0x00813000)        libpthread.so.0 => /lib/libpthread.so.0 (0x001b0000)        libstdc++.so.5 => /usr/lib/libstdc++.so.5 (0x009c7000)        libm.so.6 => /lib/libm.so.6 (0x00b0a000)        libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x0050c000)
  

  Hi mimi,

  I'm happy to report that I managed to get the code to work. I have included some of the steps I experienced the problem in case it might help improve the documentation or future generations.

  In response to your question about the "error 1" reported by do, it's just an indication that detected a compiler error (it probably resembles the return code of the compiler).

  The errors ' undefined reference... @GLIBCXX_3.4.9 "have been narrowed down. The generated labview shared library, the square.so, links to /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 which is a symlink to usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6.0.9. I decided to compare this version of libstdc ++ that included with RHEL:

  strings /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 | grep GLIBCXXGLIBCXX_3.4GLIBCXX_3.4.1GLIBCXX_3.4.2GLIBCXX_3.4.3GLIBCXX_3.4.4GLIBCXX_3.4.5GLIBCXX_3.4.6GLIBCXX_3.4.7GLIBCXX_3.4.8GLIBCXX_3.4.9GLIBCXX_FORCE_NEW
  

  strings /usr/lib/libstdc++.so.6 | grep GLIBCXXGLIBCXX_3.4GLIBCXX_3.4.1GLIBCXX_3.4.2GLIBCXX_3.4.3GLIBCXX_3.4.4GLIBCXX_3.4.5GLIBCXX_3.4.6GLIBCXX_3.4.7GLIBCXX_3.4.8GLIBCXX_FORCE_NEW
  

  So libstdc ++ RedHat does not include a string for GLIBCXX_3.4.9.

  With this in mind, I was able to get my test application to compile using the version of LabVIEW libstdc ++ using the following makefile:

  .PHONY: all cleanCPPFLAGS=-I/usr/local/natinst/nidaqmxbase/include -I/usr/local/natinst/LabVIEW-2009/cintoolsLDFLAGS=build/square.so \        /usr/local/lib/LabVIEW-2009/patchlib/libstdc++.so.6 \        -Wl,--rpath -Wl,/usr/local/lib/LabVIEW-2009/patchlib/
  
  all: test
  
  clean:        rm -f test *.o
  

  When you try to run the application, I got the following error:

  ./test: error while loading shared libraries: /usr/local/lib/liblvrtdark.so.9.0: cannot restore segment prot after reloc: Permission denied
  

  But apparently, it's because of SELinux prohibiting the use of libraries shared with moving text.
  This can be disabled by running /usr/sbin/setenforce 0 as root.

  The test application now works!

  See you soon,.

  RW