Android Mini appears as an "unknown" device

Similar Questions

• HP MINI 110 3500 - NETWORK (UNKNOWN DEVICE) CONTROLLER

  Dear Experts,

  HP mini 110-3500-windows xp

  Discovered: network controller (unknown device)

  Broadcom 802 BCM4313. 11 b/g LP - PHY

  What should I do? should I install the driver? should which driver I install?

  my laptop also impossible to activate WLAN adapt, because it is activated (written assistant wireless).

  Help me!

  Hello:

  Please see if this driver gets your wireless adapter to work.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3688868&prodNameId=3688870&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=ob-101092-1

• "Unknown device" USB Barcode scanner, problem with the USB controller driver?

  Hello

  I need assistance with our Barcode Scanners that doesn't work on our newly purchased computers at HP with Windows7 Pro x 64 operating systems.

  The brand and model of the bar code scanner is:

  Datalogic Heron D130 USB.

  When you connect the scanner to a USB port, Windows will try to install this as a HID, but it takes an unusually long time, about 7-8 seconds, to boot the device and install the drivers and appears as an unknown device in windows "devices and printers" and the hand scanner does not work.

  Sometimes when you move the USB back can I sometimes the scanner at hand to be recognized as an HID device or a Datalogic barcode scanner,

  It works fine until you restart the computer.

  After restart the computer cannot detect the scanner Barcode correctly without re - appears as unknown device.

  I suspect that there is a compatibility problem between barcode scanner and card USB controller on the computers.

  I tried to update all the drivers available on the website www.hp.com and same www.Intel.com (chipset drivers) but nothing has helped to solve this problem

  Tried newly bought barcode scanners and "used" barcode scanners earlier who works on other computers, but the problem remains.

  I found a workaround by connection of bar codes in a USB hub, and then plug the USB hub to the computer.  And leave the USB - hub to take care of the communication with the Barcode Scanner.

  in this case, it takes about 2 seconds for the code scanner barcode to mount correctly in windows under the heading "devices and printers" and then works perfectly, even after a reboot.

  I googled after a response after my problem, but it seems I'm the only one who experience this issue. ?!

  Bought more than 40 computers that I have this problem.

  These were bought at different times with two different for suppliers

  Computer model are the following

  HP ProDesk 1 400 P/N5S21EA

  Specifikations:

  http://WWW8.HP.com/emea_africa/en/products/desktops/product-detail.html?OID=6614160#! tab = specifications

  Does anyone have an idea what could be wrong and how to fix it?

  Thanks in advance

  Sincerely

  Robert T

  Hello

  The problem is not power - related.

  We use passive USB hubs that solves the problemon these computers.

  (it also works with the docks, or if you EliteDisplay E241 HP as we thers a usb hub 2 ports inbulit in monitor that works.)

  The problem lies in the incompatibility between the Intel USB controller and the hand scanner, can be connected to USB 3.0

  When you let another usb-controller support in handshakeing (such as a usb hub), it works.

  Datalogic or Intel would like to acknowledge this error.

  Because none of the big companies want to acknowledge the problem or repair, personally chose to switch to an AMD platform / CPU instead of the Intel and now it works fine!

  We get more performance for your money when AMD is usually less expensive to purchase.

  And because of the poor of Datalogic press where they don't even answer e-mail (their only channel for support)

  I chose to stop using their products. I'm going to use another provider / brand of barcodescanners.

• Tecra S2: HDD as unknown device on two of the three USB ports

  Hey again,
  I thought then that I was here anyway I could ask this too.
  The tecra S2 has 3 USB ports, they all work very well for my USB mouse and other small things like the wacom tablet...
  But when I plug my external hard drive in two of them, it says that it is an unknown device...

  I think, but am not sure, that this might have something to do with something once, we had to do in school;
  We had once set up a pilot for a small converted Converter a series (or parallel, cant he recall) cable to the usb port
  (I have already uninstalled the drivers but nothing has changed)

  It's just a guess...

  any idea on how to solve this little problem? : p

  Hello

  You said external USB HDD appears as an unknown device on two of the three USB ports.
  What appears if you connect the HARD drive to the USB port on third?
  It appears as an unknown device or what?

  The device usually appears as an unknown device in device because manager not installed device drivers.
  I check the HARD disk for the drivers and try to install it again.

• Unknown device in the device error 43 Manager

  I get a 43 unknown device error when I start Windows 7.  I tried every fix I found after ten days of research.  When Windows starts, and the notification is popping up that I can't use my keyboard are so difficult to do anything.  Finally, the message disappears (I don't know why) and I am able to type, or if I catch it just just between notifications.  At this time I started my computer in clean boot mode and no error message appears and the unknown device is not USB device controllers manager.

  What, in my view, that has happened, is that I used to have an LG phone and the software on the computer.  I now have a new phone, Samsung, that I just connected to the same port on the front of the computer.  The Samsung worked, but did not ask me to install the software, then must have run out of the LG.  I deleted the software from LG and then reconnected the Samsung and got the prompt to download the correct software.  I then plugged a generic USB hub device in order to use the phone and any other device that I could plug in (none at this time and I even unplugged the generic hub).

  Now I get the unknown device.  Some fix told me he didn't need a driver, but Windows keeps load a generic driver and so the message repeats the process over and over again.

  Unknown error seems to be a common problem, probably a fix is available from Microsoft.

  Any help would be appreciated more because it drives me crazy!

  Thanks for your reply, Al-Shabaab.  In fact, I solved the problem.

  I deleted all the Verizon and Samsung software on my computer.  When doing this, I noticed that my keyboard has gradually deteriorated (failed to start in safe mode F8 key would not work).

  I bought a new keyboard... and EUREKA!  Problem disappeared!  Then I rebooted my phone software and have had no problems since.  I guess it was a coincidence that the keyboard was dying as I tried to connect my phone to my computer leading me on a GOOSE Chase that was long, difficult and extremely frustrating!

  I appreciate the help and I hope this will help others.

• found new hardware wizard appears and unknown device device Watch Manager

  Since a few days ago, the Add New Hardware Wizard keeps popping up. I looked in Device Manager and found an unknown device (yellow exclamation mark) should I delete the device? I don't know what to do to identify which device is unknown.

  If you remove it, then he'll probably be back the next time that you start.

  go to start / all programs/windows update (at the top of the list of the menu), custom search, watch your optional hardware updates and search for a driver that you have not already installed, you can get lucky. Otherwise post the details of your specifications and ask again.

  Furthermore, it can take a while to get the pages updated and you may need to install active x on the way, a line will appear at the bottom of the fixed part of your browser screen (the same as when you download) If this is the case, click on it and install active x, then a box should appear and tell you allow I think.

• Unknown device appeared not installed in my device manager.

  Please, I need help. Unknown device appeared in my device manager after I upgraded my probook of windows 7 pro for windows pro 8.1. I don't know what to install. Please, if you know tell me.

  Hello

  Please see the link which shows you how to get the id of the hardware:

  http://www.WikiHow.com/find-hardware-ID

  then after return.

  Kind regards.

• What is that unknown device appears in Device Manager

  Hi guys, I have a camera in my driver manager that is displayed as "Unknown device" in the "other devices" section and I have no idea what device it is if I can update the driver! I tried troubleshooting my PC, but it's not helping! Please I need your help because I do not want to affect the performance of my PC. Uses a series of PC HP mini 110-3800 with Windows 7 starter installed! Thank you.

  If this is relevant, you should see an event ID 7026 Source; Service Control Manager Event Viewer. Description:
  The next (s) starting or starting system could not load:

  Feature: GIVING - it was because of a product of Viper (GFI) being uninstalled. Apparently, it deletes all the registry keys and it keeps trying to start a driver that does not exist. You can remove the registry keys:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\Root\LEGACY_SBRE
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SBRE

  If you cannot delete a key, right-click on that key and click permissions, then click on advanced, then go to the owner and you add as an owner. Then you should be able to remove the key
  Source: http://www.eventid.net/display.asp?eventid=7026&eventno=452&source=Service%20Control%20Manager&phase=1

  Go deeper, I think that the device has a connection with a mobile phone. I found references to the UAG and a driver of adfs. This is something that has been or is unsupported.

  What happens if you uninstall the device?

• Satellite L550-11th - Webcam appears as unknown device

  Hello

  I got my reinstalled (Wwindows 7-64 bit) L550.
  Now, the webcam is shown as "unknown device".

  The software on the page of Toshiba, that I installed it. Unfortunately, your camera is still unknown in Device Manager.

  Solution / or possibly the ' INF '.

  greeting
  D.Kuben

  Hello

  The webcam driver v 1.1.1.4 is available on the page of the Toshiba driver and it should work properly.
  Did you check in the BIOS in webcam settings is enabled?
  Please do this first!

  BIOS-> Advanced-> Control Panel

  If the webcam is enabled, make sure that Win 7 value added package has been installed before the webcam software.

  If that does not solve the installation problem, I recommend to try a newer version of the software of the webcam that is set to the most recent series of portable Satellite

• CD/DVD/BluRay drive will appear under unknown device

  The driver seems if be installed properly, yet it shows in the 'Unknown' category in Device Manager.  I can burn discs and play discs if I run the program as administrator, but it says that "access is denied." if I try to use the drive without specifying a run as administrator.  Screenshots can be provided if it would be of any help.

  Hi WarrenTC3,

  1 when was the last time it was working fine?

  If Device Manager cannot identify the device, it will label it an unknown device.

  When a device is not functioning, Device Manager also typically displays an error message with an error code that comes with it.

  First, check what is the code for error on an unknown device in Device Manager.

  (a) open the Device Manager , look for the unknown device.

  (b) make a right click on the device and click on Properties, search now on the tab general to find the error code.

  See the link below and run the patch available and check if this solves the problem.

  Your CD or DVD drive cannot read or write media

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  If the previous step fails, and then run the fix tool below and check out them.

  If the below fix tool does not resolve the issue then you must try the steps manual, mentioned in the following Microsoft article.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• It seems to be an unknown device in my printers/device program that I can't uninstall and appears to remote controlled... How can I remove it?

  I have recently upgraded to Windows 7 and have problems with an unknown device in printers/gear access to all my data and files including emails, applications, etc..  When I disable/uninstall this device by every way I can think it reinstalls itself...

  Hi caroleenie,

  1. What is the brand and model of the computer number?

  It seems that your computer may be affected by the virus and it can control everything on your computer.

  I suggest to download Microsoft Safety scanner and scan your computer for viruses and check how it works.

  You can download Microsoft Safety scanner from the following link.

  Microsoft safety scanner

• "Unknown device" in my device manager - but the system ready to use?

  Hi everyone, it's me again.

  I have just bought (and already exchanged for a second) a device that I want to install on my desktop. This is a Hiyatek Multi multi-function which is mainly for media card reader options provided. There is also a USB 2.0 port, fan controller, taken mic and speaker jack ports as well as the different media slots. The device is supported by Win XP

  I have the same problem persisted with this device (which I connected to the only place where I can find for the USB cables) which shows as "Unknown device" in my equipment manager. The statement indicates that Microsoft software should automatically detect the device and install the drivers for me however, the bubbles of pop-up information "Found New hardware" followed by "Unknown device" followed of "your device installed and ready to use" HUH! How can it make sense please...

  Peripheral installation mini disk that came with the camera auto works when it is inserted, but this process is stopped because the device was not recognized.

  On the motherboard to point plugin, I did reference has been used to connect my 2 front mounted USB 1.0 ports (which have now been removed) and the connector for that was a plug of white pine of 10 or 12. The new tracks to the device, I am trying to install are 4pin sheets I've located in the same orientation as the big white connector. There are some images here...

  http://i812.Photobucket.com/albums/zz48/Vanguard_01/HiyatekUSBcables2.PNG

  http://i812.Photobucket.com/albums/zz48/Vanguard_01/HiyatekUSBcables1.PNG

  http://i812.Photobucket.com/albums/zz48/Vanguard_01/Managerdisplay.PNG

  As a result, the only things that work on the new Panel are the speed controller and the speaker port.

  Also today I installed a PCI card with USB 2.0 with 3 other additional ports on the front of my machine but there is no extra connection on the card (for these 2 4 sheets, I mentioned earlier), which appear to be installed correctly from the 3rd link image above.

  I need to know if I connect it correctly or do I need to get some software from somewhere.

  Thank you

  Vanguard_1

  The answer was there in front of me!

  I got a response from Hiyatek who pointed out that cable sequence was not the same on the new sheets for my device even if they had stipulated it also on the box that it was compatible with USB 1.0 to the motherboard connections. The Green and white wires were knocked down in fact (this can be seen in the pictures). I now spliced the old Plug and the wires on the wiring of new device and it works.

  I was however not aware that there are differences in the wiring of the plug between the connections USB - is - this current?

  Vanguard_1

• M18x R2 Windows 8 "unknown device".

  Hello everyone, I have an Alienware M18x R2, which displays "Unknown device" in Device Manager.

  Here are the specs:

  I7 3920

  32GB 1600 Mhz RAM

  2 x GTX 680's

  2 x 1 TB drive HARD Western Digital 5400 RPM

  1 x 60 GB OCZ mSATA HDD

  380 Bluetooth

  WiFi killer

  Win 8 Pro 64-bit

  This particular "unknown device" does not appear with a Windows 7 operating system

  If I use Windows seven and install all recommended drivers, there is no problem, the "unknown device" in question is not yet with Windows 7 running, I did a clean Windows 7 and verified installation each device ID in Device Manager before installing anything else to see if I could find the one causing problems in Windows 8 - this is no where

  As soon as I install Windows 8 and check Device Manager, then this particular "unknown device" appears again, even after the installation of all the drivers in Windows 8 recommended is the only 'unknown' on the left.

  I tried searching the Internet using the hardware vendor ID and the device ID provided in the details section of the "unknown device" but could not find an entry useful, even using the databases of the seller and the material has been a waste of time

  Here is the hardware device ID exactly as it appears, three lines altogether, but I think the top one is relevant.

  ACPI\VEN_DELL & DEV_ABCE

  ACPI\DELLABCE

  * DELLABCE

  Any help would be great.

  See you soon

  Hi, this is certainly the driver for switching to airplane Mode. I finally could get mine put to update the other day. If you let Windows search the best pilot, it can automatically find now, he appears to have done on my machine.

• 4 "other unknown devices" in Device Manager. Windows 7 RTM 64 dv7 1450

  Just bought a computer HP dv7-1450 laptop with AMD Turion X 2 64 processors. Installed Windows 7 RTM 64 and everything seems to work except there are 4 unknown "other devices" listed in Device Manager. The 4 devices are:

  -System base unit (x 3)

  -Unknown Device (x 1)

  I have no idea what are these devices. I tried looking for drivers for chipset on the AMD and HP Web site without result. But I do not know if these are the associated chipsets. One of the devices would be the disk fall sensor hard (it does not appear in the device no matter where Manager)?

  Unfortunately on the HP site, there are not many downloads of drivers available for the 64-bit (Vista). I know that Windows 7 64 drivers won't be available until in October, but if there are not any available Vista drivers either, I expect to see all the drivers for Windows 7?

  The most important thing for me is just to know what are these "other devices" 4 and get the drivers installed.

  Thanks in advance!

  ProtectSmart Hard Drive Protection here

• Satellite L300 PSLBGE - unknown device in Device Manager

  Hello!

  I would be very grateful for any help/tips if anyone has an idea what to do...

  My friend has the laptop mentioned above (w/o OS preinstalled) and we can't get the graphics card work properly - situation is the following

  (1) mobile intel 4 series express chipset family, and an unknown device with an exclamation mark in Device Manager
  (2) both are on the same PCI BUS 0, device 2?
  (3) intel does not work because there is no free resources (I should remove the unknown device?) to work with
  (4) HW ID for the unknown device is pci ven_8086 & dev_2A43 and intel pci ven_8086 & dev_2A42 (so basically the same, right?)
  (5) Finally, and most importantly, if I go to the desktop-customize-advanced (first of all no resolution 1280 * 800) I see under adapter type:. Exactly, nothing... under properties, it appears: device not plug and play, Super VGA and under driver, I see just the status and the ability to stop, off, automatic, ask... the device at startup... If I turn it off, the screen just does not shine when the laptop is turned on...
  Any ideas? I'm insaneeeeee...

  Vista Home Premium, all other Toshiba SW installed (value pack, intel BIOS 1.9, etc. - maybe the BIOS did it?)

  Thanks in advance!

  PS maybe SP1 I now install help?

  Hello

  Wait a minute: I checked the Vendor ID and Device ID on www.pcidatabase.com and this is the graphics card Intel. So I think that's the reason why you can t change the resolution of the screen.

  I guess you forgot to install the display driver. See the Web from Toshiba site because here you can download the driver:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  After that you should t have no exclamation point.

  You can install SP1 for Vista, but that does not solve the problem with the missing display driver. But you should install it because it contains a lot of updates to security, they are important. In addition, I recommend to install SP2 for Vista.

  Good bye