Another question on the T510 restoration after an another installed sys

Similar Questions

• Problem has been detected and windows has been shutdown error STOP: 0x0000008E. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

  Original title: problem has been detected and windows has been shut down. Get the memory dump after you have installed the trial version of MS Project 2010.__space.

  Computer Message: Check if you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video cards.

  Check with your suppliers of material, updates the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to start advance startup options, and then select Safe mode.

  Technical information: * STOP: 0x0000008E (0xC0000005, 0x8054556C, 0xADB78A98, 0x00000000)

  Beginning physical memory dump

  Total physical memory dump. Contact technical support for further assistance group.

  Hi fernandomventura,

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Step 2: Follow the steps mentioned in the articles below which deals with a similar question

   

  General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"-restore the system to achieve ".

  http://support.Microsoft.com/kb/945658/

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• going, I'll be able to use the factory restore after hiding recovery drive Q?

  Hello world!!

  I recently bought E420 and I have restored factory settings once. Since then, the drive of Lenovo_recovery (Q) become visible in my exploring. Given that others also use this system, which anyone can mess with the recovery disk. I like to retrieve from the hard drive as its fast and easy so. I really never wanted to lose that drive. I tried to hide it

  I found this article on the Lenovo support site http://support.lenovo.com/en_US/detail.page?LegacyDocID=MIGR-71742 (see). I followed the steps. There were LenovoQDrivie.exe such file in my recovery disk so I download the Lenovo_hide_Drive_Q.exe and run that. After that my drive is not viisble in my exploring. I checked it the diskmanagement (make a right click my computer-gale-diskmanagement) here I can see the drive letter has been removed from this disk and see the car now, 100% free space... How can happen? is it just hidden? or I deleted the recovery because the article is for vista and other series of thinkpad? Please answer.

  I'm not currently check my system by running the factory as my system restore works very well and I have installed various related work in software.

  To check I pressed on enter at the beginning and after that I pressed F11 as flashed on screen and I could see display (Lenovo recovery screen after putting a password) which gives various restoration system - as option, command, prompt recovery of start and end of factory default restore. I don't want to take the risk I have no restore selected at the start of the factory and restarted. Defragment in window as I see this player with fragmentation of 3%.

  I just want to ask wheather my Lenovo_Drive is safe and I'll be able to use it to restore my system to factory default in the future? I don't want to try it now that the system is working fine and I don't want to take any chances.  In diskpart also I have lenovo dirve as partition 3 that is hidden. As I said could reach the screen giving 'restore defaults' opition, go, I'll be able to use this option in the future?

  Called the hotline, that they were not able to answer...

  I will be grateful if someone can help me...

  Thank you

  
  

  Hi Alexander,.

  Windows 7 recovery would erase the disk and put 7 on the entire disc.  So, you don't want that.  I didn't know you already burned disks.  It's good that you did.

  If you really want to test it, you could make a backup of the current system on external media, (such as a hard drive), and then run the recovery and restoration of the backup.  If it works, then you know recovery is correct.  If it isn't, then you could boot from the recovery discs you've done and restore it from your current backup.

  If you do not want to take the chance to test it, then at least you know that with restore disks and backup to external media that you can restore the system to its current state, no matter what happens.

  Dave

• How to restore the original partition after reformatting accidentally installing windows 10

  See the problem below. I can not get a USB stick formatted with FAT to be recognized by bootcamp or to download the drivers to continue.

  The problem occurred after that my son wanted to re - install windows 7 after that that he has been upgraded to windows 10 and utilities disk to reformat the drive hard windows installed.

  

  OS X Terminal, you can post the output of

  diskutil list

• Can I reinstall an app that I bought from the app store after a clean install of El Capitan?

  Hi all

  I did a clean install of El Capitan, which made my 2011 macbook pro currently unusable.

  A few days after installation I met problems I've ever had before. Baffled because since my drive hard worked completely fine with the Mavericks and Lion. No disk ever utility error. Computer froze a couple times the 5 years ive had the it. It has been stable.

  I explained my failed attempts to solve this problem in another thread here.

  So, if this is not relative, which seems to be caused all of this, I concluded it's a failing hard drive?

  My question is the only program of value I have logical hard disk Pro X (bought and downloaded 3 days ago) so anyway, given my problems with the hard drive I have can always reinstall logic after I got a new drive and reinstalled OSX?

  I'm on a PC at the moment and looked everywhere to find my purchase history of Logic Pro X. The only thing I can find official is my receipt by e-mail. I logged on the apple.com site with my Apple ID and it show nothing bought for the last 90 days. Active iPhone and cant find a purchase history. This suggests to me that you need to check on a mac on the App Store?

  Yes. You will need to check and it redownload via the Mac App Store with the original ID of Apple.

  (139819)

• Not able to install the HP software after a clean install of win7, hpbi and harddisk.dll error

  Hello

  I bought a tm2 with win7 home x 64, my IT guy at the office have installed win7 ultimate x 64 and of course all the HP software was missing when I returned. Fortunately, they recorded the old files and I was able to locate the SwSetup folder and managed to install essential drivers.

  However, I miss all the HP software, which means that I can no longer find it not in the SwSetup folder or it will not be installed. I found the HP Touch Smart 'something' Center (folderHPTSLC) but I get the error "hp\bin\hpbi" and I found the Recovery Manager win7 HP homepage, but I get the error "hardDisk.dll.

  I am really a bit upset that I have to spend so much time to solve a simple problem, I have an intact recovery partition, a partition HP tools intact as well as all the files in the SwSetup folder, how can it be difficult?

  I want the software I paid and so far, I spent several hours looking for a solution to a seemingly simple problem (just provide the software on your hp, or at least one that reinstalls the Sw from the hard drive to the HP computer if you fear that your software may be used on other HP computers...).

  Can someone please provide me with is the solution to the problems mentioned above, a link to the HP Touch Center application work (although I have the files, he just moved there) or tell me how I can restart the installation of the HP software and driver that happens just after you have configured your win7?

  Thank you

  Geen

  I agree, our IT screwed up guy, they didn't even know the upgrade thing... :-/

  In any case, I found a way to install the software I was looking for, just unzip to a folder and run the .msi file in the src folder.

  Even if not all the applications had such a record, most of 'em had.

  After playing with the sw a bit, I realized that I didn't like it anyway, boy I'm glad, I wasn't going to come home!

  and btw, we bought a HP Mini and it was a nice little software, called AppInstl in his swsetup, actually just the sw file I was looking for. Of course the same thing happened with the Mini ('clean' installation), but with this app, that I managed to re - install all the sw I wanted without any problem, except QuickWeb, of course, but that seems to be a general problem.

  Seems to me that HP has also seen the need for a "easy install your software after clean install" app.  :-)

  Thanks for all your comments, my problem was solved!

  Rgds,

  Geen

• Firefox crashes when it starts. I tried to reset it; I uninstalled and reinstalled no question. The problems started after I changed my video card

  Crash ID: bp-1c18c383-28e4-426c-96a7-ff97e2130906
  OS: Windows 7 SP1 64-bit
  I had to change my video card, immediately after this FF started crashing at the beginning.
  The graphics card is a Nvidia GeForce 210.
  I tried to:
  -Reset FF;
  -uninstall, delete the registry, reinstall it;
  -Windows Update;
  -Update (311.06) video card drivers
  but no way.
  I can start FF mode without failure.
  Any help will be really appreciated.

  I solved it by disabling hardware acceleration in the FF options.
  There seems to be a conflict between FF and some drivers from Nvidia.

• Unable to open the system restore after a virus attack. Get an error, the status of the channel is disabled, Code 230

  OP: The State of the channel is not valid Code 230

  some poured a group of viruses on my VISTA computer. I've tired to restore to an earlier period, but can not get the restore to run. I tried to locate rstrui.exe and right-clicking it goes then properties. Restore to an earlier period does not come to the top. If I click left on rstrui.exe I get the same message, the line is not valid.

  I looked in the forum and have not found an answer to this problem. I have the 7 update. install this would fix the problem?

  Hello snail,

  Do a system restore is not a better way to get rid of viruses on your computer. You should start with the execution of an on-line analysis of Windows Onecare on your computer. Follow the link below to run the scan Windows Onecare online on your computer:

  http://OneCare.live.com/site/en-my/default.htm?mkt=en-my

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

• Need help to get the system restored after Trojan virus. does not work in safe mode

  We were running without anti-virus software.  System started running very slow and wouldn't normally.  He has started in Mode safe has finally got and ran Malwarebytes detected 2 Trojan virus.  Those removed, installed Norton in safe mode, but can not get computer to open in normal mode for the comprehensive analysis of norton and difficulty.  Help!

  The only way to be sure you are free of malware is to format and start over.

  If you have a backup from before the problem you can restore.

  If not and you have the win 7 dvd you can re - install.
  '
  If not and you have a factory restore partition, you can restore from that.

  If this isn't a clean install.  You will need a win 7 dvd and number series.

• Unable to do the Windows updates after I freshly installed XP

  It is a new installation on a dell computer to a xp I had on another computer that no longer works.  There has not been a single update yet. The website has encountered a problem and cannot display the page you are trying to view. The options provided below may help you solve the problem.

  For self-help options:

  • Frequently asked Questions
  • Find Solutions
  • Windows Update Newsgroup

  To support options:

  • Microsoft online assisted support (no cost for Windows Update issues)

  Original title: I was not able to do a single update.  I copied what he says and hides in the details

  It is a new installation on a dell computer to a xp I had on another computer that no longer works.  There has not been a single update yet. The website has encountered a problem and cannot display the page you are trying to view. The options provided below may help you solve the problem.

  For self-help options:

  • Frequently asked Questions
  • Find Solutions
  • Windows Update Newsgroup

  To support options:

  • Microsoft online assisted support (no cost for Windows Update issues)

  Clean install of Windows XP?  This OS is old enough that you will put on a little extra effort.

  Get SP2 (manually) and save it to your desktop. (There's a link here.) [You are a COMPUTER professional for now.]

  Install it.

  Then restart at least a couple of times for a few minutes between each restart.

  Get SP3 (manually) and save it to your desktop. (There's a link here.) [You are a COMPUTER professional for now.]

  Install it.

  Then restart at least a couple of times for a few minutes between each restart.

  Download at least Internet Explorer 7 (if it is not Internet Explorer 8).

  Install it.

  Reset.

  Now try to get 100 + post-SP3 updates - restart and revisit the http://windowsupdate.microsoft.com/ after each reboot site, until you have fully updated.

  Then, use the serial number of the machine to go to the they offer for that specific computer from Dell Support and drivers site and download the latest hardware.

  If go you...

• Press the scrolling issues after a clean install of 7.

  I recently installed 7 with a cloth from disk on my Pavilion dv4.  After a successful installation, the only thing I see that does not work is the scroll on my touch pad feature.  I need to find a new driver for 7?

  Hey Mathew,.

  Welcome to the Forum,

  Try this:

  The system Web site:

  HP Pavilion dv4-1281us notebook PC

  Look in Categotry "driver - keyboard, mouse and input devices" > "ALPS pointing device...."

  Download the driver on your computer (save), double-click it to install it.

  While you're there (at your Web page), you can bookmark and pick up another software that you want for your system.

  I hope this helps.

  Say 'Thank you' by clicking on the stars Kudos in the post helped you.

  Mark a message 'acceptable' to say that your problem is solved.

• my computer must be started in safe mode and then restored after that I installed updates

  This problem started in 2010 object.  I had to reinstall Windows for the second time, the problem started on 30-45 days after that.

  Maybe you should explain the prolem and why you had to reinstall.

  Read also: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/1467f44b-ee27-4f7d-98d7-f1c4b35b3395

  Now after back with all the information necessary to help you further.

  It is even possible that all you need to do is reset WU
  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Thank you.

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• problem with access to the image data after you have installed latest windows

  Hi, my name s mayur, I got the problem when I open my photos data, actuly I have a computer laptop sony vaio there and I m a photographer so usually I saved my data in my vista drive was slove, so I upgraded mwan Formate c drive and install windows 7 in there then when I cheack my image data in f drive I cant able to see the thuumbs when I open it in the windows image viewer He told me i dnt have the permission to access

  I did this solutions

  I changed my user to administrator - has not worked
  I changed the security settings and gives full control to user - does not work
  I've changed owner ship - does not work, I reinstalled vista - not worked
  I used hodden administrator - has not worked
  I have attached the HDD in the pc of windows genuen - has not worked
  I opened my hard drive under linux and not worked

  I am a hardware engineer also so can someone tell me what will be the reson when I cheak the propertese folder there are a few user (s16561613) with red qustion mark in the authenticated user, my laptop has a genuien windows and now I have installed the windows is not genuine and I dnt have the original windows. so is this problem related to the license... or is the problem of pricing to someone please help me... the security and

  Hello

  There will not be any support for a pirated copy of Windows. I suggest you install a genuine Windows 7 on the computer and test the issue. If you face the same problem let us know so that we can help you further.

  Reference:

  Windows Genuine

  http://Windows.Microsoft.com/en-us/Windows/genuine

• SE error message during the update downloads after you have installed the CS5 Suite on new Windows 10 PC

  I just bought a new PC running Windows 10.

  I downloaded my CS5 programs using my license out of the web of Adobe. So far so good. The download went well and programs seem to work fine, however, when I go to register the product, he won't let me.

  Also, when I download updates ARE available, they have error messages saying download errors, try again later.

  Try to download the updates manually:

  Updates

• How to change the database metadata after OIM/OAM installed?

  Hello world

  To change the database/schema of metadata for our installation OIM/OAM.

  What I intend to do is:

  1. create the new db

  2. run the RCU for the OID and OAM utility.

  3. change the connection pool data source in the Weblogic OAM console.

  Is there anything else I need to do?

  I know, there was a connection to the database when I created the home field of the OID (via config.sh). I tried to run this script config again, but could not find a way to change the domain, nor I see how do in one of the consoles (much).

  Any help appreciated!
  D

  for OID, updated if necessary tnsnames.ora and data sources

  OAM, update data sources.

  For IOM, consult this section docID 1359656.1: configuration of JDBC connection of IOM in metalink demand side.