AnyConnect acl

Similar Questions

• AnyConnect customer to destination site to site

  Would like some general information for configuration 2 ASAs connected over the VPN site-to site and have then remote AnyConnect client to connect to the site of the end.

  The two ASAs are set up for the site-to-site VPNs as shown in the enclosed drawing.  Guests on each LAN segment can ping through the tunnel from site to site.

  One of the ASAs acts also as an endpoint endpoint for customers AnyConnect.  AnyConnect remote users can see items on the 192.168.1.X subnet that is shown on the seal (and elements behind the router not shown) successfully.  Apart from the interface of the ASAs are the endpoints for all the cyrpto.

  Where I am wrong configures the ASAs so users remote AnyConnect sees the 192.168.2.X network and general guidelines is appreciated.

  Few things: these IPs aren't my IPs production and do not want to include output config.  No other than static routing routing is configured between ASAs and layer-3 systems.  For users in the 192.168.1.X subnet their default gateway is configured to be the router 192.168.1.1.  For users of the 192.168.2.X network their default gateway is configured to be the ASA 192.168.2.1.  Attached diagram shows generally how I am and what I want to accomplish.

  What I think I need is:

  A static route on ASA 192.168.2.1 to 192.168.102.0/24 network to? inside the interface of 192.168.1.254?

  Exemption on the two ASAs for the remote user to/from the network 192.168.2.X NAT traffic.

  If you can comment, point me to examples of online configuration or comments, it would be appreciated.

  Hello

  If I understand correctly, you must allow the AnyConnect customer (that connect to the ASA) communicate through the IPsec tunnel to the other ASA and reach 192.168.2.x

  What you need to do is in the crypto ACL of the tunnel-a Site to include another AS with the 192.168.102.x (which is the AnyConnect customer pool).

  Also, on the split tunneling AnyConnect ACL (if you use split tunneling), include the network remote 192.168.2.x).

  Example:

  Let '; s say it's your ACL split of the tunnel for the AnyConnect customer

  list of allowed shared access ip 192.168.1.0 255.255.255.0 192.168.102.0 255.255.255.0

  Thus, you must also include:

  list of allowed shared access ip 192.168.2.0 255.255.255.0 192.168.102.0 255.255.255.0

  Let's say you have this ACL as the crypto ACL for the tunnel from Site to Site

  license of crypto list to access ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0

  Then, add this line:

  license of crypto list to access ip 192.168.2.0 255.255.255.0 192.168.102.0 255.255.255.0

  To allow the ASA redirect back on the same interface traffic it receives, you add

  permit same-security-traffic intra-interface

  In addition, check the NAT configuration in order to include these networks as a result.

  Hope that makes sense, let's know us any question.

  Federico.

• After disconnection of the ACL AnyConnect not honored on ISA550W

  Once I have disconnect a session SSL - VPN (AnyConnect), the firewall blocks WAN > LAN traffic. I navigate to the firewall > access control > rules ACL page and click on the Reset button for the ISA550W to honor the rules.

  Hi Eric,.

  Thanks for providing this information.  We have been able to reproduce it here.  You can open a case with HWC so we can work on that with you?

  Let me know if you have problems opening a case with HWC.

  Thank you

  Brandon

• ASA5520 and ACS 4.0 - AnyConnect WebVPN (Clientless SSL Tunnel) does not downloadable ACLs (DACL)

  I'm having a lot of problems called "Clientless SSL-Tunnel" AnyConnect VPN sessions - i.e. those that are enacted by visit https:// via a browser, and let the Java/ActiveX plugin will automatically run Fat Client AnyConnect VPN for you - downloadable ACL honor.

  Our installation is integrated via RADIUS Cisco ACS 4.0.

  Dynamic group-> connection profile strategy seems to work for either (direct according to AnyConnect VPN Client heavy or indirectly via a browser-> /Java Client ActiveX), however, our only downloadable ACL take affect if the user instantiates the SSL VPN via AnyConnect VPN Client Fat; first of all, users who access the site through the "Browser-> https://" route seem to have no ACLs applied to all?

  I understand that I can change the custom "Cisco VPN/3000/etc" parameters RADIUS, such as 'WebVPN-filters' and 'WebVPN-Access-List' to apply an ACL configured locally on the firewall of the SAA, but what I have to configure to make the sessions ' WebVPN/Clientless-SSL-Tunnel"to honor the DACL that sends our ACS?

  It is a known problem with some Software ASA Versions see bug cisco CSCtv19046 - DACL is not applied to acre during connection via the Web portal. You probably need to update your ASA 8.4 (4.1) or a later version.

• ACL and anyconnect ssl vpn

  Hello world

  I was testing the few things at my lab at home.

  PC - running ssl vpn - sw - router - ISP - ASA (anyconnect ssl)

  AnyConnect ssl works very well and I am also able to access the internet.

  I use full tunnel

  I have ACLs on the external interface of the ASA

  1

  True

  any

  any

  intellectual property

  Deny

  0

  By default

  []

  I know that the ACL is used to traffic passing by ASA.

  I need to understand the flow of traffic for internet via ssl vpn access. ?

  Concerning

  MAhesh

  As you correctly say, the ACL interface is not important for that because the VPN traffic is not inspected by the ACL. Of the at least not by default.

  You can control the traffic with a different ACL that is applied to the group policy with the command "vpn-filter". And of course you need a NAT rule that translates your traffic when running to the internet. This rule should work on the pair of interface (outside, outside).

• IPsec vpn and Anyconnect is denied by the ACL (unknown)

  I am trying to configure IPsec VPN and I used the wizard of asdm (asdm version 8.4, ASA version 8.4). At the moment he is not in production and is in a test environment. Whenever I try to VPN in I get an error on the asdm syslog saying "TCP access denied by ACL from x.x.x.122 to outside:x.x.x.225/443. So I allowed all VPN traffic to this IP address that is currently the IP address as the external interface. My acl is as follows:

  outside_in list extended access permit tcp any interface outside eq https

  outside_in list extended access permit tcp any host x.x.x.225 eq https

  Access-group outside_in in external interface

  Yet, I still get the same exact error. The strange thing about this error is that it does not give me the specific ACL that denies access. There is no other access lists that could possibly block this traffic.

  No idea what could be the cause this problem because I am confused.

  So far, if you have configured following does not require an acl.

  ciscoasa(config)#webvpn
  ciscoasa(config-webvpn)#enable outside
  ciscoasa(config-webvpn)#svc enable
  You can post configuration here someone can have a look on that.
  Thanks
  Ajay
  
  
  
  

• ACL rule does not work after the SSL VPN connection

  Hello

  I have the following configuration:

  -VLAN LAN (192.168.5.0/24)

  -VLAN WLAN (192.168.20.0/24)

  -SSL VPN VLAN (192.168.200.0/24)

  Default policy denies access to the local network. If the value rule ACL to allow traffic between WLAN and LAN. Works very well.

  Now I connect with AnyConnect and access resources on the network VLAN. Works.

  After you have disconnected the VPN I can't access the LAN to WLAN VLAN. If I disable the ACL rule and turn it back on, it works again until someone connects with SSL VPN.

  I use firmware 1.2.15. Any ideas when this bug fixed?

  Kind regards

  Simon

  HI Simon,.

  This bug will be fixed in 1.2.16.

  I don't know the exact date for the release.

  But it should be out soon. If you need the fix sooner,

  Please open a case of pension.

  Kind regards

  Wei

• Rules ACL ISA550W "hanging".

  Hey guys, I use an ISA550W with firmware firmware 1.2.15 on it.  I have a handful of interfaces LAN configured, whose two operating as DMZ (but I don't see the point to configure as a DMZ?)-see attached for more details.

  So far, it works great, but every now and then the only ACL rule I added manually stops working and the cup of my local network Mgmt OOB access.  If I "Reset" of the table of the ACL, the rule immediately starts to work again and access is restored.

  Has anyone else seen elsewhere?  Other options for sanitation?

  Thank you

  Phil

  Hi Phil,

  We saw some problems with AnyConnect affecting the ACL.  The good new s 1.2.17 has just been published.  Please go to 1.2.17 and test to see if that helps.

  Let me know if you have any questions in this regard.

  Thank you

  Brandon

• IOS anyconnect vpn group lock and user restrictions

  Dear Experts,

  I now have two questions about cisco IOS vpn on ISR G2:

  1 is it possible to lock user group in IOS anyconnect VPN we can do in ASA? If so, can someone share the steps for her?

  2 - a customer wishes to restrict the anyconnect user login as it might turn the connection to the user on request. That is to say whenever the user wants to connect via vpn to ask the administrator to allow connection. can we do without deleting the username and create again?

  the other may be on ASA or IOS.

  Please see this guide:

  http://www.Cisco.com/c/en/us/support/docs/security/iOS-easy-VPN/117634-c...

  As he points out, "for the Cisco IOS group-lock and the ipsec: use vpn-group, it only works for IPSec (the easy VPN server)." In order to group-lock specific users in specific contexts of WebVPN (and strategies Group attached), authentication domains should be used. »

  If you lock a user to a policy that authenticates, but does provide real access permissions (say an ACL that blocks all traffic to the private network) then you have essentially made their ability to non-functional connection.

  If you use an external AAA server (for example, RADIUS or LDAP), then you can move in and out of the group which is authorized without disable VPN access / delete their account altogether.

• AnyConnect dynamic address pool

  It is possible using DAP to assign the different address for anyconnect users pool?

  Currently, I check if the PC has some elements such as process, save the key and activated applications.

  If yes-> ACL using "allow normal access.

  Is not-> ACL uses 'access '.

  That works, but two computers uses the pool of customer addresses defined in the configuration of the Tunnel

  tunnel-group remoteaccess General attributes
  remoteaccess-pool1 address pool

  It is possible to also dynamically set the address pool?

  If yes-> ACL using 'Allow normal access' & 'remoteaccess-pool1'

  SE not-> 'Access restricted' ACL uses & "remoteaccess-pool2.

  Thank you!

  Rolando A. Valenzuela.

  Hello Rolando,

  Correct than me if I'm wrong, based on the computer (the domain to which it belongs) that you want to map to some Grouppolicy, which has some qualities as the pool of addresses, and that way you can establish a distinction, one area to the other, let's say:
  (Admins/domain gets the address pool of 10.10.10.0/24)
  (Suppliers/field gets the address pool of 10.20.20.0/24)

  Based on this I will give you my recommendations, if you want to do it based on the computer and not the user, I recommend you to get all the computers in the same group of users in Active Directory, so if you have a group of users (Admin / domain group) you can add computers, and with the LDAP Mapping attribute you can map based on membership in a specific political group in this way, all computers that use of Admin users, will be assigned to a group policy with several attributes, such as the Pool of local IP, if users don't below any of the advertised groups, they will not be able to connect either, because you will need create a group policy NO ACCESSIBLE to be used for users who should not connect You can find more information here:

  - http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-nex...

  Another medium, will be filtering the PC based on the MAC address, YES this function uses a regular expression to match the organizational (YES) the unique identifier that will allow the PC connect so those that match the program defined in the regular expression with Regex LUA , this is possible, you can find this regular expression, for example :

  assert(function ()    local pattern = "^d067\.e5*"    local true_on_match = true
  
      local match = false    for k,v in pairs(endpoint.device.MAC) do        print(k)        match = string.find(k, pattern)        if (match) then            if (true_on_match) then                return true            else return (false)            end        end    endend)()

  If the PC is HP or Dell, you can use the MAC address YES part and set it there and allow the user to connect, and the user peuvent then be mapped with the Protocol LDAP attribute mapping to a group policy so they will be able to connect with a different IP address. (DAP cannot assign IP address), it's a dynamic access policy that works with HostScan Module of Posture to do a preliminary assessment and as he says unit of Posture, NOTE: PAH itself gives you the ability to filter by individual MAC address, so you don't need to do it by YES, this is common for large companies that have a large amount of users , so they prefer to make Yes that is easier, but you can set the MAC address of another way will be to use another regular expression so DAP can examine the first 3 letters (Case Insensitive) of the PC and then allow it to connect if it matches the regex, if it's not, the connection ends, you can find the regular expression here :

  assert(function()    local match_pattern = "^[Mm][Ss][Vv]"         -> Those are the 3 first letters    local match_value   = endpoint.device.hostname  --> Specifying hostname      if (type(match_value) == "string") then        if (string.find(match_value, match_pattern) ~= nil) then            return true        end    elseif (type(match_value) == "table") then        local k,v        for k,v in pairs(match_value) do            if (string.find(v, match_pattern) ~= nil) then                return true            end        end    end    return falseend)()

  In addition to regular expressions of LUA:- http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-nex... To do this you must License Premium AnyConnect (then Yes you can use the default two value that comes with the ASA). Also, you must have image CSD or Hostscan in ASA and activated so that you can get that kind of information about the computers that connects the AnyConnect. You can use the AnyConnect image like hostscan image. (do not forget to activate the attributes of endpoint through Deputy Ministers, DEPUTIES of the section of the CSD, otherwise it won't work). The previous mentioned is good options for you to explore, but it will not be very scalable (depending on number of users), so I recommend than a registry key with check check "Domain name" or file would work well but its your CUs call if he wants to still check MAC or not. Please do not forget to rate and score as correct this message if it helped, keep me posted! Best regards, David Castro,

• Cannot ping the Anyconnect client IP address to LAN

  Hi guys,.

  I have an old ASA5520 running 9.1 (6) 8 where I installed Anyconnect SSL split tunneling access:

  See establishing group policy enforcement
  attributes of Group Policy DfltGrpPolicy
  VPN-tunnel-Protocol ikev1, ikev2 clientless ssl

  lanwan-gp group policy internal
  gp-lanwan group policy attributes
  WINS server no
  DNS server no
  VPN - connections 1
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value lanwan-acl
  by default no
  WebVPN
  AnyConnect value lanwan-profile user type profiles

  permit for line lanwan-acl access-list 1 standard 172.16.0.0 255.254.0.0 (hitcnt = 48) 0xb5bbee32

  Now I can ping, RDP, etc. of any VPN host connected to any destination within 172.16.0.0 255.254.0.0 range.

  Here is my routing information:

  See the road race
  Route outside 0.0.0.0 0.0.0.0 69.77.43.1 1
  Route inside 172.16.0.0 255.254.0.0 172.25.8.1 1

  interface GigabitEthernet0/1
  nameif inside
  security-level 100
  IP 172.25.8.4 255.255.254.0

  But I can't ping any Anyconnect VPN client connected from my LAN.

  See the establishment of performance ip local pool

  mask IP local pool lanwan-pool 172.25.9.8 - 172.25.9.15 255.255.254.0

  Here's the traceroute of LAN:

  C:\Users\Florin>tracert d 172.25.9.10

  Determination of the route to 172.25.9.10 with a maximum of 30 hops

  1 1 ms<1 ms="" 1="" ms="">
  2<1 ms="" *=""><1 ms="">
  3 * the request exceeded.
  4 * request timed out.

  While the ASA routing table has good info:

  show route | I have 69.77.43.1

  S 172.25.9.10 255.255.255.255 [1/0] via 69.77.43.1, outdoors

  Other things to mention:

  -There is no other FW between LAN and the ASA

  -There is no FW or NAT configured or enabled on this ASA(see her running nat and see the race group-access they return all two virgins).

  -FW Windows on the Anyconnect workstation is disabled (the service is running). I also tested and able to ping to my workstation Anyconnect House of another device on the same network.

  So, I'm left with two questions:

  1. first a I do not understand: after reading some threads here, I added this line standard lanwan-acl access-list allowed 69.77.43.0 255.255.255.0

  out of ping and tracert commands remains the same, but now I can RDP to the docking station VPN connected to any workstation LAN;

  What happens here?

  2. how can I do ICMP work after all? I also tried fixup protocol icmp and icmp Protocol Error Correction, still no luck

  Thanks in advance,

  Florin.

  Hi Florin,

  The entire production is clear enough for me

  in debugging, you can see that traffic is constituent of the ASA

  "Inside ICMP echo request: 172.17.35.71 outside: 172.25.9.9 ID = 22 seq = 14024 len = 32.

  the SAA can be transferred on or can be a downfall for some reason unknow

  can we have a wireshark capture on the vpn client to see if the icmp request is to reach the customer? I want to just isolate the problem of fw so that we can concentrate on the ASA rather than silly windows ;) fw

  made the RDP Protocol for VPN client for you inside the LAN work?

  run logging on ASA and ping and then inside to VPN client and the Coachman connects on the firewall, if ASA comes down the pkt it will appear in the log.

  loggon en
  debug logging in buffered memory

  #sh logging buffere | in icmp

  #Rohan

• Cisco ASA 5510 - restrictions of VPN (AnyConnect) based on the AD user or IP address

  Hello

  I want to test how to restrict access user on an ASA 5510 AnyConnect. In politics, I can define what networks will go through the VPN tunnel and which not (split tunneling). The ASA has a LDAP connection and only AD users with a special security group can connect over AnyConnect.
  On the other hand I would like to restrict access for special users within a VPN policy.

  So my question:
  What are your recommendations to implement this szenario?

  My two ideas would be:
  1. the access rules based on the user of the AD.
  2. special reserve IP addresses in the pool of addresses AnyConnect for some users, so I can limit access to the normal firewall rules base based on the source IP address.

  What are your recommendations and is it possible to realize my ideas (and how)?

  Thanks in advance

  Best regards

  Hello

  I will suggest that you configure a second ad group in the server and another group strategy in the ASA, you can configure certain access on each group policy "the installer of the filters, assign different split political tunnel, different ACL' and in the ad server, you can assign users for example to the AD Group A and AD Group B based on the access you want to give them now , you must configure LDAP mapping to assign the user specific group policy that you want based on the AD group that they belong.

  You can follow this documentation that will help you configure the LDAP Mapping:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Best regards, please rate.

• ASA Anyconnect with PBR

  Hello

  We have a customer who upgraded his ASA to version 9.5.1 and now wants to use ACB for users connected by Anyconnect.
  Today, ASA is configured with an ACL filter which local networks is only allowed in the Tunnel.
  We tried to use the ACB in order to put all traffic through the Tunnel and the next another device on the side break LAN.

  AnyConnect Network: 172.18.18.0/24
  LAN network: 172.18.16.0/24
  Default to use for the anyconnect customer gateway: 172.18.16.202

  It was created an ACL standard for traffic of correspondence 172.18.18.0, a road map which next-hop is 172.18.16.202 and applied to the external interface.

  Gateway 172.18.16.202 knows that net 172.18.18.0/24 is on ASA (static route)

  It is my understanding no? I have configured as indicated above, but did not work.

  Kind regards

  Regis

  Hi Regis,

  If you want to send all Anyconnect traffic to a specific host on the LAN site (next hop), you can use the 'tunnel route' function instead of the ACB.

  Check more information below:

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-next-generation-firewalls/112182-SSL-TDG-config-example-00.html

  It may be useful

  -Randy-

• AnyConnect Assistant, traffic will not work

  I am in the process of establishing an ASA with anyconnect for someone and rather perplexed.

  Have used the anyconnect Wizard and everything seems fine, I can connect to the ASA 5505 of the House, but my internet no longer works and I can't reach anything inside network (172.16.0.0)

  I set up a tunnel of split in policy (using the GUI) and made a list of access of 172.16.0.0. This has no effect. I have to specify the range of pool VPN as well in this access list? the VPN range for customers is 192.168.145.0

  I get an IP in that range when I log in, but my print road, default for internet 0.0.0.0 route is out of my ethernet interface as usual, with a metric of 20, there's another road for internet 0.0.0.0 default but that points to my interface anyconnect with a metric of 2.

  That would explain why my internet does not work when connected, there is also a road to 172.16.0.0, but this does not indicate the address of interface anyconnect. He points again to my ethernet interface. what I am doing wrong?

  1. make sure that you allow subnets behind site B in the list of split tunnel (as applicable)

  2 create a rule of exemption nat (outdoors, outdoor)

  3. make sure that you have the same security permitted intra-interface traffic

  4 leave the anyconnect subnet in the encryption, ACLs on site A and B

• ASA Anyconnect VPN do not work or download the VPN client

  I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config

  XXXX # sh run
  : Saved
  :
  ASA Version 8.4 (3)
  !
  hostname XXXX
  search for domain name
  activate pFTzVNrKdD9x5rhT encrypted password
  zPBAmb8krxlXh.CH encrypted passwd
  names of
  !
  interface Ethernet0/0
  Outside-interface description
  switchport access vlan 20
  !
  interface Ethernet0/1
  Uplink DMZ description
  switchport access vlan 30
  !
  interface Ethernet0/2
  switchport access vlan 10
  !
  interface Ethernet0/3
  switchport access vlan 10
  !
  interface Ethernet0/4
  Ganymede + ID description
  switchport access vlan 10
  switchport monitor Ethernet0/0
  !
  interface Ethernet0/5
  switchport access vlan 10
  !
  interface Ethernet0/6
  switchport access vlan 10
  !
  interface Ethernet0/7
  Description Wireless_AP_Loft
  switchport access vlan 10
  !
  interface Vlan10
  nameif inside
  security-level 100
  IP 192.168.10.1 255.255.255.0
  !
  interface Vlan20
  nameif outside
  security-level 0
  IP address x.x.x.249 255.255.255.248
  !
  Vlan30 interface
  no interface before Vlan10
  nameif dmz
  security-level 50
  IP 172.16.30.1 255.255.255.0
  !
  boot system Disk0: / asa843 - k8.bin
  passive FTP mode
  DNS lookup field inside
  DNS domain-lookup outside
  DNS domain-lookup dmz
  DNS server-group DefaultDNS
  Name-Server 8.8.8.8
  Server name 8.8.4.4
  search for domain name
  network obj_any1 object
  subnet 0.0.0.0 0.0.0.0
  network of the Webserver_DMZ object
  Home 172.16.30.8
  network of the Mailserver_DMZ object
  Home 172.16.30.7
  the object DMZ network
  172.16.30.0 subnet 255.255.255.0
  network of the FTPserver_DMZ object
  Home 172.16.30.9
  network of the Public-IP-subnet object
  subnet x.x.x.248 255.255.255.248
  network of the FTPserver object
  Home 172.16.30.8
  network of the object inside
  192.168.10.0 subnet 255.255.255.0
  network of the VPN_SSL object
  10.101.4.0 subnet 255.255.255.0
  outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
  outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
  outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
  outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
  outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
  outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
  Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
  vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
  pager lines 24
  Enable logging
  timestamp of the record
  exploitation forest-size of the buffer to 8192
  logging trap warnings
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 dmz
  local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 647.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
  NAT (exterior, Interior) static source VPN_SSL VPN_SSL
  !
  network obj_any1 object
  NAT static interface (indoor, outdoor)
  network of the Webserver_DMZ object
  NAT (dmz, outside) static x.x.x.250
  network of the Mailserver_DMZ object
  NAT (dmz, outside) static x.x.x.. 251
  the object DMZ network
  NAT (dmz, outside) static interface
  Access-group outside_in in external interface
  Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  AAA-server protocol Ganymede HNIC +.
  AAA-server host 192.168.10.2 HNIC (inside)
  Timeout 60
  key *.
  identity of the user by default-domain LOCAL
  Console HTTP authentication AAA HNIC
  AAA console HNIC ssh authentication
  Console AAA authentication telnet HNIC
  AAA authentication secure-http-client
  http 192.168.10.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ca trustpoint localtrust
  registration auto
  Configure CRL
  Crypto ca trustpoint VPN_Articulate2day
  registration auto
  name of the object CN = vpn.articulate2day.com
  sslvpnkey key pair
  Configure CRL
  Telnet 192.168.10.0 255.255.255.0 inside
  Telnet timeout 30
  SSH 192.168.10.0 255.255.255.0 inside
  SSH timeout 15
  SSH version 2
  Console timeout 0
  No vpn-addr-assign aaa

  DHCP-client update dns
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd outside auto_config
  !
  dhcpd address 192.168.10.100 - 192.168.10.150 inside
  dhcpd allow inside
  !
  dhcpd address dmz 172.16.30.20 - 172.16.30.23
  dhcpd enable dmz
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  authenticate the NTP
  NTP server 192.168.10.2
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal VPN_SSL group policy
  VPN_SSL group policy attributes
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list vpn_SplitTunnel
  the address value VPN_SSL pools
  WebVPN
  activate AnyConnect ssl dtls
  AnyConnect Dungeon-Installer installed
  AnyConnect ssl keepalive 15
  AnyConnect ssl deflate compression
  AnyConnect ask enable
  ronmitch50 spn1SehCw8TvCzu7 encrypted password username
  username ronmitch50 attributes
  type of remote access service
  type tunnel-group VPN_SSL_Clients remote access
  attributes global-tunnel-group VPN_SSL_Clients
  address VPN_SSL pool
  Group Policy - by default-VPN_SSL
  tunnel-group VPN_SSL_Clients webvpn-attributes
  enable VPNSSL_GNS3 group-alias
  type tunnel-group VPN_SSL remote access
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect esmtp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
  : end

  XXXX #.

  You do not have this configuration:

   object network DMZ nat (dmz,outside) static interface

  Try and take (or delete):

   object network DMZ nat (dmz,outside) dynamic interface