AnyConnect VPN connected but not in LAN access

Hello

I just connfigured an ASA to remote VPN. I think everything works but I do not have access

for customers in the Local LAN behind the ASA.

PC <==internet==>outside of the SAA inside<=LAN=> PC

After AnyConnect has established the connection I can ping inside the Interface of the ASA

but I can't Ping the PC behind the inside Interface.

Here is the config of the ASA5505:

: Saved

:

ASA Version 8.2 (1)

!

asa5505 hostname

activate 8Ry2YjIyt7RRXU24 encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.1.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP 192.168.178.254 255.255.255.0

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

Shutdown

!

interface Ethernet0/3

Shutdown

!

interface Ethernet0/4

Shutdown

!

interface Ethernet0/5

Shutdown

!

interface Ethernet0/6

Shutdown

!

interface Ethernet0/7

Shutdown

!

passive FTP mode

Inside_ICMP list extended access permit icmp any any echo response

Inside_ICMP list extended access permit icmp any any source-quench

Inside_ICMP list extended access allow all unreachable icmp

Inside_ICMP list extended access permit icmp any one time exceed

access-list outside_cryptomap_2 note ACL traffic von ASA5505 zur ASA5510

outside_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.178.0 255.255.255.0

tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0

pager lines 24

Within 1500 MTU

Outside 1500 MTU

mask 192.168.1.10 - 192.168.1.15 255.255.255.0 IP local pool SSLClientPool

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access no_NAT

NAT (inside) 1 192.168.1.0 255.255.255.0

Access-group Inside_ICMP in interface outside

Route outside 0.0.0.0 0.0.0.0 192.168.178.1 1

Route outside 192.168.10.0 255.255.255.0 192.168.178.230 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

dynamic-access-policy-registration DfltAccessPolicy

AAA authentication http LOCAL console

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set-3DESSHA FRA esp-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

card crypto outside_map 2 match address outside_cryptomap_2

peer set card crypto outside_map 2 192.168.178.230

card crypto outside_map 2 game of transformation-FRA-3DESSHA

outside_map interface card crypto outside

Crypto ca trustpoint localtrust

registration auto

domain name full cisco - asa5505.fritz.box

name of the object CN = cisco - asa5505.fritz.box

sslvpnkeypair key pair

Configure CRL

Crypto ca certificate chain localtrust

certificate fa647850

3082020b a0030201 30820174 020204fa 0d06092a 64785030 864886f7 0d 010104

0500304 06035504 03131763 6973636f 617361 35353035 2e667269 2d 3120301e a

747a2e62 6f783126 30240609 2a 864886 f70d0109 02161763 6973636f 2d 617361

2e667269 35353035 747a2e62 6f78301e 170d 3132 31303132 31383434 31305a 17

323231 30313031 38343431 06035504 03131763 6973636f 3120301e 305a304a 0d

617361 35353035 2e667269 747a2e62 6f783126 2a 864886 30240609 f70d0109 2D

6973636f 02161763 2d 617361 35353035 2e667269 747a2e62 6f783081 9f300d06

d6279e1c 8181009f 092a 8648 86f70d01 01010500 03818d 30818902 00 38454fc 9

705e1e58 762edc35 e64262fb ee55f47b 8d62dda2 102c8a22 c97e395f 2a9c0ebb

f2881528 beb6e9c3 89d91dda f7fe77a4 2a1fda55 f8d930b8 3310a05f 622dfc8f

d48ea749 7bbc4520 68 has 06392 d65d3b87 0270e41b 512a4e89 94e60167 e2fa854a

87ec04fa e95df04f 3ff3336e c7437e30 ffbd90b5 47308502 03010001 300 d 0609

2a 864886 04050003 81810065 cc9e6414 3c322d1d b191983c 97b474a8 f70d0101

2e5c7774 9d54d3ec fc4ee92d c72eef27 a79ce95a da83424f b05721c0 9119e7ea

c5431998 e6cd8272 de17b5ff 5b1839b5 795fb2a0 2d10b479 056478fa 041555dd

bfe3960a 4fe596ec de54d58b a5fa187e 5967789a a26872ef a33b73ec 7d7673b9

c8af6eb0 46425cd 2 765f667d 4022c 6

quit smoking

crypto ISAKMP allow outside

crypto ISAKMP policy 1

preshared authentication

3des encryption

sha hash

Group 2

life 86400

crypto ISAKMP policy 65535

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH timeout 5

Console timeout 0

management-access inside

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

localtrust point of trust SSL outdoors

WebVPN

allow outside

SVC disk0:/anyconnect-win-2.3.0254-k9.pkg 1 image

SVC disk0:/anyconnect-wince-ARMv4I-2.3.0254-k9.pkg 2 image

enable SVC

tunnel-group-list activate

internal SSLClientPolicy group strategy

attributes of Group Policy SSLClientPolicy

VPN-tunnel-Protocol svc

Split-tunnel-policy tunnelspecified

Split-tunnel-network-list value split tunnel

the address value SSLClientPool pools

WebVPN

SVC Dungeon-Installer installed

time to generate a new key of SVC 30

SVC generate a new method ssl key

SVC request no svc default

username password asdm privilege Yvx83jxa2WCRAZ/m number 15

hajo 2w8CnP1hHKVozsC1 encrypted password username

hajo attributes username

type of remote access service

tunnel-group 192.168.178.230 type ipsec-l2l

IPSec-attributes tunnel-group 192.168.178.230

pre-shared-key *.

type tunnel-group SSLClientProfile remote access

attributes global-tunnel-group SSLClientProfile

Group Policy - by default-SSLClientPolicy

tunnel-group SSLClientProfile webvpn-attributes

enable SSLVPNClient group-alias

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the netbios

inspect the rsh

inspect the rtsp

inspect the skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect the tftp

inspect the sip

inspect xdmcp

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:0008564b545500650840cf27eb06b957

: end

What wrong with my setup.

Concerning

Hans-Jürgen Guenter

Hello Hans,.

You should change your VPN pool to be a different subnet within the network, for example: 192.168.5.0/24

Then configure NAT exemption for traffic between the Interior and the pool of vpn.

Based on your current configuration, the following changes:

mask 192.168.5.10 - 192.168.5.15 255.255.255.0 IP local pool SSLClientPool

no_NAT to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0

And then also to enable icmp inspection:

Policy-map global_policy

class inspection_default

inspect the icmp

Tags: Cisco Security

Similar Questions

  • Client VPN connects but not internal LAN access or Ping

    Hi all.

    I'm new on this forum and kindly asking for your help because I'm stuck.

    I have an ADSL router cisco 877 which I configured easy VPN server.
    Now the Cisco VPN client ver 5.0 to connect successfully to the VPN server, but when you try to access/ping computers on the internal network, there is no response.

    The configuration is below. Please let know us where I was going or what I missed.
    [code]

    Building configuration...

    Current configuration: 4574 bytes
    !
    version 12.4
    no service button
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    encryption password service
    !
    boot-start-marker
    boot-end-marker
    !
    enable secret 5 $1$ $86dn J8HrK9kCQ8G9aPAm6xe4o1
    enable password 7 13151601181B54382F
    !
    AAA new-model
    !
    !
    AAA authentication login default local
    AAA authentication login internal_affairs_vpn_1 local
    AAA authorization exec default local
    AAA authorization internal_affairs_vpn_group_1 LAN
    !
    !
    AAA - the id of the joint session
    !
    Crypto pki trustpoint TP-self-signed-2122144568
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 2122144568
    revocation checking no
    rsakeypair TP-self-signed-2122144568
    !
    !
    TP-self-signed-2122144568 crypto pki certificate chain
    self-signed certificate 03
    30820248 308201B 1 A0030201 02020103 300 D 0609 2A 864886 F70D0101 04050030
    2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
    69666963 32313232 31343435 6174652D 3638301E 170 3032 30333032 32303537
    31375A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
    4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 31323231 65642D
    34343536 3830819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
    8100D3EA 07EC5D66 F4DD8ACC 5540BDBE 009B3C26 598EC99C D99D935A 51292F96
    F495E5A9 8D012B0E 73EA7639 3B 586799 187993F5 ED9CA31C 788756DD 6BDB1B2B
    4D7AA7F0 B07CF82F F2A29E86 E18B442C 550E22D2 E92D9914 105B7D59 253BBEA1
    D84636B4 A4B4B300 7946CE84 E9A63D2E 7789B03A 6ADDB04E B21EC207 CCFEAE0B
    30 HAS A 50203 010001, 3 1 130101 301B 0603 030101FF FF040530 0F060355 70306E30
    551 1104 14301282 10494E54 45524E41 4C5F4146 46414952 53301F06 03551D 23
    04183016 8014FA0F B3C9C651 7FD91EFA 3F63EAE8 6C83C80D 8AE2301D 0603551D
    0E041604 14FA0FB3 C9C6517F D91EFA3F 63EAE86C 83C80D8A E2300D06 092A 8648
    86F70D01 01040500 03818100 A1026DDC C91CAEB2 3C62AF92 D6B25EB2 CA 950, 920
    313BCF26 4A35B039 A4F806A0 8CB54D11 6AF1ABAA A770604B 4403F345 0351361B
    E2CF2950 26974F4A 95951862 401A4F76 C816590C 2FFCB115 9A8B3E96 4373FFE1
    33D744F7 E0FDDE61 B5B48497 9516C3C6 A3157957 C621668E A83B5E33 2420F962
    9142DD9E B6E9D74A 899A 9653
    quit smoking
    dot11 syslog
    IP cef
    No dhcp use connected vrf ip
    DHCP excluded-address IP 10.10.10.1
    !
    IP dhcp pool dhcplan
    Network 10.0.0.0 255.0.0.0
    DNS-server 196.0.50.50 81.199.21.94
    default router 10.10.10.1
    Rental 7
    !
    !
    property intellectual auth-proxy max-nodata-& 3
    property intellectual admission max-nodata-& 3
    name of the IP-server 81.199.21.94
    !
    !
    !
    VPN username password 7 095A5E07
    username fred privilege 15 password 7 1411000E08
    username ciscovpn password 7 01100F175804101F2F
    !
    !
    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    !
    ISAKMP crypto client configuration group internal_affairs_vpn
    key *.
    DNS 196.0.50.50 81.199.21.94
    pool ippool
    ACL 108
    !
    !
    Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
    !
    Crypto-map dynamic internal_affairs_DYNMAP_1 10
    Set transform-set RIGHT
    market arriere-route
    !
    !
    card crypto client internal_affairs_CMAP_1 of authentication list internal_affairs_vpn
    card crypto isakmp authorization list internal_affairs_vpn_group_1 internal_affairs_CMAP_1
    client configuration address card crypto internal_affairs_CMAP_1 answer
    ipsec 10-isakmp crypto map internal_affairs_CMAP_1 Dynamics internal_affairs_DYNMAP_1
    !
    Archives
    The config log
    hidekeys
    !
    !
    !
    Bridge IRB
    !
    !
    interface Loopback0
    2.2.2.2 the IP 255.255.255.255
    !
    ATM0 interface
    no ip address
    ATM vc-per-vp 512
    No atm ilmi-keepalive
    PVC 0/32
    aal5snap encapsulation
    Protocol ip inarp
    !
    DSL-automatic operation mode
    Bridge-Group 1
    !
    interface FastEthernet0
    !
    interface FastEthernet1
    !
    interface FastEthernet2
    !
    interface FastEthernet3
    !
    interface Vlan1
    description of the local lan interface
    IP 10.10.10.1 255.0.0.0
    IP nat inside
    IP virtual-reassembly
    !
    interface BVI1
    internet interface Description
    IP 197.0.4.174 255.255.255.252
    NAT outside IP
    IP virtual-reassembly
    internal_affairs_CMAP_1 card crypto
    !
    IP local pool ippool 192.168.192.1 192.168.192.200
    IP forward-Protocol ND
    IP route 0.0.0.0 0.0.0.0 196.0.4.173
    !
    IP http server
    local IP http authentication
    IP http secure server
    IP nat inside source list interface BVI1 NAT overload
    IP nat inside source static tcp 2.2.2.2 23 23 BVI1 interface
    !
    NAT extended IP access list
    allow an ip
    !
    access-list 108 allow ip 10.0.0.0 0.255.255.255 192.168.192.0 0.0.0.255
    !
    !
    !
    control plan
    !
    Bridge Protocol ieee 1
    1 channel ip bridge
    !
    Line con 0
    password 7 0216054818115F3348
    no activation of the modem
    line to 0
    line vty 0 4
    password 7 06160E325F59590B01
    !
    max-task-time 5000 Planner
    end

    Since this is a named ACL, you need to change ACL configuration mode:

    NAT extended IP access list

    Then, make the changes.

    Federico.

  • VPN connects but no remote LAN access

    Hello

    I'll put up on a PIX 501 VPN remote access.

    When I try to connect via VPN software, I am able to connect but I am unable to access LAN resources.

    I have pasted below part of which seems relevant to my setup. I'm stuck on this issue, could someone help me? Thanks in advance.

    ethernet0 nameif outside security0
    nameif ethernet1 inside the security100
    test.local domain name
    name 10.0.2.0 inside
    name 10.0.2.13 MSExchange-en
    2.2.2.2 the MSExchange-out name

    outside_access_in tcp allowed access list all gt 1023 host 2.2.2.2 eq smtp
    outside_access_in list access permit tcp any host 2.2.2.2 eq https
    outside_access_in list access permit tcp any host 2.2.2.2 eq www
    inside_outbound_nat0_acl 10.0.2.0 ip access list allow 255.255.255.0 192.168.235.0 255.255.255.192
    access-list 101 permit icmp any one

    3.3.3.3 exterior IP address 255.255.255.0
    IP address inside 10.0.2.254 255.255.255.0
    IP local pool vpn_pool 192.168.235.1 - 192.168.235.15
    IP local pool vpn_pool_2 192.168.235.16 - 192.168.235.40

    1 3.3.3.4 (outside) global
    NAT (inside) 0-list of access inside_outbound_nat0_acl
    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
    static (inside, outside) 2.2.2.2 10.0.2.13 netmask 255.255.255.255 1000 1000
    Access-group outside_access_in in interface outside
    Route outside 0.0.0.0 0.0.0.0 3.3.3.1 1

    RADIUS Protocol RADIUS AAA server
    AAA-server RADIUS (inside) host 10.0.2.3 * timeout 10
    AAA-server local LOCAL Protocol

    Permitted connection ipsec sysopt
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-MD5
    map outside_map 90-isakmp ipsec crypto dynamic dynmap
    card crypto outside_map the LOCAL RADIUS client authentication
    outside_map interface card crypto outside
    ISAKMP allows outside
    part of pre authentication ISAKMP policy 20
    ISAKMP policy 20 3des encryption
    ISAKMP policy 20 md5 hash
    20 2 ISAKMP policy group
    ISAKMP duration strategy of life 20 86400
    vpngroup signal address vpn_pool pool
    vpngroup dns-server 10.0.2.3 signal
    vpngroup default-field test.local signal
    vpngroup idle time 1800 signal
    vpngroup max-time 14400 signal
    signal vpngroup password *.
    vpngroup TF vpn_pool_2 address pool
    vpngroup dns-server 10.0.2.3 TF
    TF vpngroup default-domain test.local
    vpngroup TF 1800 idle time
    vpngroup max-time 14400 TF
    TF vpngroup password *.

    Kind regards

    Joana

    Very similar to the question of the configuration of the switch. You should check if there is no specific roads on the switch outside the default gateway. The switch should route the subnet pool ip to the firewall (10.0.2.254).

  • Ipad Cisco ipsec VPN connects but not access to the local network

    Hi guys,.

    I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

    If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

    Cisco 877.

    My config is attached.

    Any ideas?

    Thank you

    Build-in iPad-client is not useful to your configuration.

    You have three options:

    (1) remove the ACL of your vpn group. Without split tunneling client will work.

    2) migrate legacy config crypto-map style. Here, you can use split tunneling

    3) migrate AnyConnect.

    The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

  • Cisco AnyConnect VPN connection has not changed my public IP address on Windows 7 64 bit

    Hello

    I installed a customer Cisco AnyConnect VPN from my school, so that I can access school of my Windows 7 laptop at home network. I was able to connect, but when I used http://www.whatismyip.com/, it still shows the IP address assigned by my ISP.  The "network and sharing Center", I have my original LAN and LAN VPN upward but access to LAN VPN type is 'without Internet access. The VPN connection seems to have activities based on evolution bytes sent and received.

    I searched the Web for solutions and changed something like adding the entry door. But it did not help.

    Thanks for your help.

    Split tunnel is probably configured so that traffic destined to school networks pass through the VPN tunnel, and traffic destined to the Internet goes outward through your local ISP. That's why whatismyip show your public IP address from ISP.

  • VPN connects but cannot ping or access resources

    I hope this is an easy fix and it's something that I am missing.  I've been looking at this for several hours.

    Scenario:

    I Anyconnect Essentials so I use the SSL connection

    I changed my domain name and external IP in my setup, I write.

    My VPN connection seems to work very well.  In fact, I was able to connect to 3 locations with 3 different external IP address.

    1 location, I get IP address 192.168.30.10, as it should.  I can ping 192.168.1.1, but not the 192.168.1.6 which is my temporary resource, the firewall is disabled on 192.168.1.6.

    2 location, I get an IP of 192.168.30.11, as it should.  I was able to ping 192.168.30.10, could not sue 192.168.1.1 as the place closed.

    Any help would be appreciated, it's getting late so I hope I gave enough details.  I feel so close but yet so far.

    See the ciscoasa # running

    : Saved

    :

    ASA Version 8.2 (1)

    !

    ciscoasa hostname

    names of

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 22.22.22.246 255.255.255.252

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    clock timezone CST - 6

    clock to summer time recurring CDT

    DNS lookup field inside

    DNS domain-lookup outside

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    ICMP-type of object-group ALLOWPING

    echo ICMP-object

    ICMP-object has exceeded the time

    response to echo ICMP-object

    Object-ICMP traceroute

    Object-ICMP source-quench

    ICMP-unreachable object

    access-list 10 scope ip allow a whole

    10 extended access-list allow icmp a whole

    pager lines 24

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    mask 192.168.30.10 - 192.168.30.25 255.255.255.0 IP local pool SSLClientPoolNew

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 1 192.168.1.0 255.255.255.0

    Route outside 0.0.0.0 0.0.0.0 22.22.22.245 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    network-acl 10

    WebVPN

    SVC request no svc default

    AAA authentication LOCAL telnet console

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Telnet 0.0.0.0 0.0.0.0 inside

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    management-access inside

    dhcpd dns 8.8.8.8

    dhcpd outside auto_config

    !

    dhcpd address 192.168.1.5 - 192.168.1.36 inside

    dhcpd allow inside

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow inside

    allow outside

    AnyConnect essentials

    SVC disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 1 image

    SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 2 image

    enable SVC

    tunnel-group-list activate

    internal SSLClientPolicy group strategy

    attributes of Group Policy SSLClientPolicy

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    field default value mondomaine.fr

    the address value SSLClientPoolNew pools

    WebVPN

    SVC Dungeon-Installer installed

    time to generate a new key of SVC 180

    SVC generate a new method ssl key

    SVC value vpngina modules

    attributes of Group Policy DfltGrpPolicy

    VPN-tunnel-Protocol webvpn

    username test encrypted password privilege 15 xxxxxxxxxxxxxx

    username ljb1 password encrypted xxxxxxxxxxxxxx

    type tunnel-group SSLClientProfile remote access

    attributes global-tunnel-group SSLClientProfile

    Group Policy - by default-SSLClientPolicy

    tunnel-group SSLClientProfile webvpn-attributes

    enable SSLVPNClient group-alias

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    Policy-map global_policy

    class inspection_default

    inspect the icmp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:ed683c7f1b86066d1d8c4fff6b08c592

    : end

    Patrick,

    'Re missing you the excemption NAT. Please add the following and try again:

    access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.30.0 255.255.255.0

    NAT (inside) 0 access-list sheep

    Let us know if you still have problems after that.

    Raga

  • I am trying to create a VPN connection, but it does not work

    I am trying to create a VPN connection, but it does not work
    The wizard cannot establish a connection. And if I try to record simply does not connect
    It does not work. If I try to click on find the problem, there simply
    do nothing.
    I tried it on another pc, where it worked. So the problem is not the
    router or data network. And the curious thing is that I installed it before, but only from one day to the other, the VPN connection was missing.

    It does not create even a the connection icon
    Thank you

    Try a system restore to a Date before the problem began:

    Restore point:

    http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

    Do Safe Mode system restore, if it is impossible to do in Normal Mode.

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    http://www.windowsvistauserguide.com/system_restore.htm

    Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

    See you soon.

    Mick Murphy - Microsoft partner

  • Customer Cisco PIX 501 VPN connects but no connection to the local network

    Hi all:

    I am able to make a VPN connection to a PIX 501. The remote client is assigned an IP (192.168.2.1) also, but not able to access all the machines in the local network connected to the PIX.

    I have attached the PIX configuration.

    Advice will be greatly appreciated.

    ********************

    6.3 (5) PIX version

    interface ethernet0 car

    interface ethernet1 100full

    ethernet0 nameif outside security0

    nameif ethernet1 inside the security100

    enable password xxxx

    passwd xxxxx

    pixfirewall hostname

    domain ciscopix.com

    fixup protocol dns-length maximum 512

    fixup protocol ftp 21

    fixup protocol h323 h225 1720

    fixup protocol h323 ras 1718-1719

    fixup protocol http 80

    fixup protocol rsh 514

    fixup protocol rtsp 554

    fixup protocol sip 5060

    fixup protocol sip udp 5060

    fixup protocol 2000 skinny

    fixup protocol smtp 25

    fixup protocol sqlnet 1521

    fixup protocol tftp 69

    names of

    access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

    access-list 102 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

    pager lines 24

    Outside 1500 MTU

    Within 1500 MTU

    IP address outside dhcp setroute

    IP address inside 192.168.1.1 255.255.255.0

    alarm action IP verification of information

    alarm action attack IP audit

    IP local pool ippool 192.168.2.1 - 192.168.2.5

    location of PDM 192.168.2.0 255.255.255.0 outside

    PDM logging 100 information

    history of PDM activate

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) - 0 102 access list

    NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

    Timeout xlate 0:05:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

    H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

    Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00

    Timeout, uauth 0:05:00 absolute

    GANYMEDE + Protocol Ganymede + AAA-server

    AAA-server GANYMEDE + 3 max-failed-attempts

    AAA-server GANYMEDE + deadtime 10

    RADIUS Protocol RADIUS AAA server

    AAA-server RADIUS 3 max-failed-attempts

    AAA-RADIUS deadtime 10 Server

    AAA-server local LOCAL Protocol

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    SNMP-Server Community public

    No trap to activate snmp Server

    enable floodguard

    Permitted connection ipsec sysopt

    Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

    Crypto-map dynamic dynmap 10 transform-set RIGHT

    map mymap 10-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    ISAKMP allows outside

    ISAKMP identity address

    part of pre authentication ISAKMP policy 10

    encryption of ISAKMP policy 10

    ISAKMP policy 10 md5 hash

    10 2 ISAKMP policy group

    ISAKMP life duration strategy 10 86400

    vpngroup vpn3000 ippool address pool

    vpngroup vpn3000 Server dns 68.87.72.130

    vpngroup vpn3000-wins 192.168.1.100 Server

    vpngroup vpn3000 split tunnel 101

    vpngroup vpn3000 downtime 1800

    password vpngroup vpn3000 *.

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd address 192.168.1.2 - 192.168.1.33 inside

    dhcpd lease 3600

    dhcpd ping_timeout 750

    dhcpd outside auto_config

    dhcpd allow inside

    Terminal width 80

    Cryptochecksum:xxxx

    ****************

    The DNS server is the one assigned to me by my ISP.

    My internal network connected to the PIX is 192.168.1.1 - 192.168.1.33 and the VPN ip pool is 192.168.2.1 - 192.168.2.5

    "isakmp nat-traversal 20" can do the trick.

  • I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are greyed out.

    I am trying to create a VPN connection, but when I get to the step that allows me to create the VPN, the radial buttons are grayed out, it is a Windows component is missing and does not allow me to create VPN. I am running Windows XP Home addition. I recently got a Malware attack and had the quarantine and fix trojen attempts. After the restoration, I found that my previous VPN connection was broken. When I tried to add a new connection, I'm stuck on the screen connection virtual network in the the radial button private network connection wizard is grayed out, he could not check.

    Hello

    Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Windows XP TechNet forum. You can follow the link to your question:

    http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

  • My laptop connects is more to the internet, either hard wired or wireless. When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.

    My laptop connects is more to the internet, either hard wired or wireless.  When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.  My other computer has service very well (or I wouldn't send this message) I checked everything, what to do?

    original title: internet connection.

    Hi vonhatten,

    1. Did you the latest changes on the computer?
    2. You receive an error message when you try to connect to the internet?
    3. You have security software installed on the computer?

    Refer to the article below and try the steps mentioned, check if it helps.

    In Windows network connection issues

    http://support.Microsoft.com/kb/313242

  • E4200 Mac connects but not PC after crash

    We had a power failure.  Connection Wi - Fi disturbed and has not corrected itself as in the past.

    A MAC and android os phone will connect but not PC with different operating systems.

    Wired computers will connect and go on the internet but not when try wireless on windows PC.

    I have a comcast modem and a router wireless e4200.

    Tried the re-engining of the modem and the router.

    Tried to unplug Cisco on computers and then reconnect to wireless connection.

    Sometimes laptops will discover the excellent show and Cisco of the signal power but does not connect.

    Wireless is enabled on laptop computers.

    Do not know what has changed this causes for the victory of the PC only.  (IP? etc?)

    Any help is appreciated.

    Thank you.

    Thank you for the answers.

    I did a factory reset within the connection on the router.

    After resetting my settings it works fine.

    No idea what scattered settings.

  • I created a vpn connection, but can I create a shortcut to connect every time?

    I created a vpn connection, but can I create a shortcut to connect every time?

    I created a vpn connection, but can I create a shortcut to connect every time?

    Open network and sharing Center, go to the Edit card settings window and drag the VPN icon on your desktop.

  • connected but not connected

    Hello
    on 11g on HP UNIX.

    Can not understand: connected but not connected:
    sqlplus sys@+ASM as sysdba
    
    Enter password:
    ERROR:
    ORA-12154: TNS : 
    Enter user-name: sys as sysdba
    Enter password:
    Connected.
    SQL> select * from v$instance;
    select * from v$instance
    *
    ERROR at line 1:
    ORA-01012: not logged on
    Any idea?
    Thank you.

    sqlplus sys@+ASM as sysdba
    ORA-12154: TNS:
    Enter the user name: sys as sysdba

    SQL > select * from v$ instance;
    Select * from v$ instance
    *
    ERROR on line 1:
    ORA-01012: not connected

    You connect to the instance by TNS connect descriptot ASM?
    Which alert log file shows?

    tnsping + ASM

  • Cisco vpn 5.0.07.0440 - k9 connected but not the network remote access to Windows 8.1 pro

    I use 5.0.07.0440 - k9 vpn Cisco and Cisco vpn 5.0.07.0290 - k9 both version on our 8.1 Windows Mobile pro.
    VPN connected successfully, but not remote access network and receive no ping.

    But when I try with wifi and vpn, then good job.

    Please help me as soon as possible.

    Thank you
    Sanjib

    It is very problematic on Windows 8 and EOL now.

    Kind regards

    Nehmaan

  • VPN client connected but no ping nor access to privat network

    Hello

    I have a 1802w installed, a VPN client that can connect to the router and L2L connection, which works very well.

    On the router, I see that the client is connected, but no traffic passes. In sh crypto ipsec, I see that traffic is decrypted, but no packtets are encypted.

    Can someone point me in the right direction? I have the confs and debugs attached. Thanks for the help in advance.

    Erich

    Erich,

    Looking at your configuration, two things:

    1 - is the current running configuration. I see your Tunnel L2L is configured with an address of correspondence of 101, but I don't see a 101 ACL set on the router.

    2. your Split Tunnel must be reconfigured. Which means, the source and destination must be exchanged.

    SplitList extended IP access list

    permit ip 192.168.2.0 0.0.0.255 192.168.111.0 0.0.0.255

    Split Tunneling

    http://www.Cisco.com/en/us/Tech/tk59/technologies_configuration_example09186a00800a393b.shtml#Con4

    Also, the IP address pool you assign to clients, ensure that they are not part of a LAN on your side. If so, you can then run in routing problems.

    Kind regards

    Arul

    * Please note all useful messages *.

Maybe you are looking for