AnyConnect VPN connection VPN site access to remote site

I need our VPN users to gain access to our remote site (Site to Site VPN), there is no problem to access the main site through the VPN. Crypto map sites have the VPN pool in the card encryption.

Any ideas?

Here is the main Site (ASA5520) config inside 192.168.50.0

crypto_vpn_remote-site access-list extended ip 192.168.50.0 allow 255.255.255.0 172.16.1.0 255.255.255.0

IP 192.168.99.0 allow Access-list extended site crypto_vpn_remote 255.255.255.0 172.16.1.0 255.255.255.0

inside_nat0_outbound to access extended list ip 192.168.50.0 allow 255.255.255.0 172.16.1.0 255.255.255.0

access extensive list ip 192.168.99.0 inside_nat0_outbound allow 255.255.255.0 172.16.1.0 255.255.255.0

Remote site (PIX 515E) inside 172.16.1.0

access-list crypto_vpn_main-site permit ip 172.16.1.0 255.255.255.0 192.168.50.0 255.255.255.0

access-list crypto_vpn_main-site permit ip 172.16.1.0 255.255.255.0 192.168.99.0 255.255.255.0

access-list sheep permit ip 172.16.1.0 255.255.255.0 192.168.50.0 255.255.255.0

access-list sheep permit ip 172.16.1.0 255.255.255.0 192.168.99.0 255.255.255.0

VPN (AnnyConnect) 192.168.99.0

On the main site, pls make sure that you have 'same-security-traffic permit intra-interface' active.

Also, if you have split tunnel configured, please also make sure that he understands the Remote LAN (172.16.1.0/24).

Hope that helps.

Tags: Cisco Security

Similar Questions

  • AnyConnect VPN site to site fiber destined

    I'm installing AnyConnect in two places. There is a fiber point to point between the two locations, and they can communicate through it without any problem on the spot. I want to use AnyConnect to connect to A branch then also be able to access resources through the PTP Protocol to branch B. I tried some with split tunneling configuration changes, but nothing seems to be convey me. I have attached two ASA configs. Any help would be greatly appreciated!

    A: the 192.168.1.x site

    B: from the site 192.168.200.x

    On each ASA you need two lines below.  One for the local internal lan subnet and one for the remote lan subnet.  IN the case of the AESC, it must use the subnet VPN global (the address pool).

    nat (inside,outside) source static INTERNAL_SUBNET INTERNAL_SUBNET destination static VPN_SUBNET VPN_SUBNET
  • no client AnyConnect vpn internet access

    AnyConnect vpn client no internet no access.

    Here is the configuration. Help, please.

    Thank you

    Jessie

    ASA Version 8.2 (1)

    !

    hostname ciscoasa5505

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 172.16.0.1 255.255.0.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address 69.x.x.54 255.255.255.248

    !

    interface Vlan5

    Shutdown

    prior to interface Vlan1

    nameif dmz

    security-level 50

    DHCP IP address

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    DNS lookup field inside

    DNS domain-lookup outside

    DNS server-group DefaultDNS

    Server name 172.16.0.2

    Server name 69.x.x.6

    object-group Protocol TCPUDP

    object-protocol udp

    object-tcp protocol

    object-group service TS-777-tcp - udp

    port-object eq 777

    object-group service Graphon tcp - udp

    port-object eq 491

    object-group service TS-778-tcp - udp

    port-object eq 778

    object-group service moodle tcp - udp

    port-object eq 5801

    object-group service moodle-5801 tcp - udp

    port-object eq 5801

    object-group service 587 smtp tcp - udp

    EQ port 587 object

    outside_access_in list extended access permit tcp any host 69.x.x.50 eq imap4

    outside_access_in list extended access permit tcp any host 69.x.x.52 eq ftp

    outside_access_in list extended access allowed object-group TCPUDP any object-group of 69.x.x.50 host smtp-587

    outside_access_in list extended access permit tcp any host 69.x.x.52 eq telnet

    outside_access_in list extended access permit tcp any host 69.x.x.52 eq ssh

    outside_access_in list extended access allowed object-group TCPUDP any host object-group moodle-5801 69.x.x.52

    outside_access_in list extended access permit tcp any host 69.x.x.52 eq smtp

    outside_access_in list extended access permit tcp any host 69.x.x.52 eq https

    outside_access_in list extended access permit tcp any host 69.x.x.52 eq www

    outside_access_in list extended access permit tcp any host 69.x.x.50 eq ftp

    outside_access_in list extended access permit tcp any host 69.x.x.50 eq smtp

    outside_access_in list extended access permit tcp any host 69.x.x.50 eq pop3

    outside_access_in list extended access allowed object-group TCPUDP any host 69.x.x.50 EQ field

    outside_access_in list extended access permit tcp any host 69.x.x.50 eq https

    outside_access_in list extended access permit tcp any host 69.x.x.50 eq www

    outside_access_in list extended access allowed object-group TCPUDP any host 69.x.x.51 EQ field

    outside_access_in list extended access allowed object-group TCPUDP any host TS-778 69.x.x.51 object-group

    outside_access_in list extended access allowed object-group TCPUDP any host Graphon 69.x.x.51 object-group

    outside_access_in list extended access permit tcp any host 69.x.x.51 eq https

    outside_access_in list extended access permit tcp any host 69.x.x.51 eq www

    outside_access_in list extended access allowed object-group TCPUDP any host TS-777 69.x.x.50 object-group

    outside_access_in list extended access permit tcp any host 69.x.x.54 eq https

    access extensive list ip 172.16.0.0 outside_cryptomap_1 allow 255.255.0.0 192.168.50.0 255.255.255.0

    access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.0.0 255.255.255.0

    inside_nat0_outbound list of allowed ip extended access all 172.16.0.32 255.255.255.224

    access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.50.0 255.255.255.0

    access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.0.0 192.168.1.0 255.255.255.0

    inside_access_in of access allowed any ip an extended list

    Standard Split-Tunnel access list permit 172.16.0.0 255.255.0.0

    access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.0.0 255.255.255.0

    access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.50.0 255.255.255.0

    access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 192.168.1.0 255.255.255.0

    access-list SHEEP extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0

    access extensive list ip 172.16.0.0 outside_cryptomap allow 255.255.0.0 192.168.0.0 255.255.255.0

    access extensive list ip 172.16.0.0 outside_cryptomap_2 allow 255.255.0.0 192.168.1.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    MTU 1500 dmz

    IP local pool VPN_Users 172.16.100.10 - 172.16.100.20 mask 255.255.255.0

    IP local pool anypool 172.16.0.9 - 172.16.0.19 mask 255.255.0.0

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0 access-list SHEEP

    NAT (inside) 1 0.0.0.0 0.0.0.0

    public static 69.x.x.50 (Interior, exterior) 172.16.0.2 netmask 255.255.255.255

    public static 69.x.x.51 (Interior, exterior) 172.16.1.2 netmask 255.255.255.255

    public static 69.x.x.52 (Interior, exterior) 172.16.1.3 netmask 255.255.255.255

    inside_access_in access to the interface inside group

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 69.x.x.49 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    Enable http server

    http 172.16.0.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    card crypto outside_map 1 match address outside_cryptomap

    card crypto outside_map 1 set pfs

    card crypto outside_map 1 set 208.x.x.162 counterpart

    card crypto outside_map 1 set of transformation-ESP-3DES-SHA

    card crypto outside_map 2 match address outside_cryptomap_1

    card crypto outside_map 2 set pfs

    card crypto outside_map 2 peers set 209.x.x.178

    card crypto outside_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    card crypto outside_map 3 match address outside_cryptomap_2

    card crypto outside_map 3 set pfs

    card crypto outside_map 3 peers set 208.x.x.165

    card crypto outside_map 3 game of transformation-ESP-3DES-SHA

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    3des encryption

    sha hash

    Group 1

    life 86400

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd outside auto_config

    !

    dhcpd address 172.16.0.20 - 172.16.0.40 inside

    dhcpd dns 172.16.0.2 69.x.x.6 interface inside

    dhcpd allow inside

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow outside

    SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

    enable SVC

    tunnel-group-list activate

    attributes of Group Policy DfltGrpPolicy

    Server DNS 172.16.0.2 value

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    Group Policy inside sales

    Group sales-policy attributes

    value of server DNS 172.16.1.2 172.16.0.2

    VPN-tunnel-Protocol svc

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value split Tunnel

    WebVPN

    SVC mtu 1406

    internal group anyconnect strategy

    attributes of the strategy group anyconnect

    VPN-tunnel-Protocol svc webvpn

    WebVPN

    list of URLS no

    SVC request to enable default webvpn

    username of graciela CdnZ0hm9o72q6Ddj encrypted password

    graciela username attributes

    VPN-group-policy DfltGrpPolicy

    tunnel-group 208.x.x.165 type ipsec-l2l

    208.x.x.165 group of tunnel ipsec-attributes

    pre-shared-key *.

    tunnel-group AnyConnect type remote access

    tunnel-group AnyConnect General attributes

    address anypool pool

    strategy-group-by default anyconnect

    tunnel-group AnyConnect webvpn-attributes

    Group-alias anyconnect enable

    allow group-url https://69.x.x.54/anyconnect

    tunnel-group 208.x.x.162 type ipsec-l2l

    208.x.x.162 tunnel ipsec-attributes group

    pre-shared-key *.

    tunnel-group 209.x.x.178 type ipsec-l2l

    209.x.x.178 group of tunnel ipsec-attributes

    pre-shared-key *.

    !

    Global class-card class

    match default-inspection-traffic

    !

    !

    World-Policy policy-map

    Global category

    inspect the icmp

    !

    service-policy-international policy global

    context of prompt hostname

    : end

    Hello

    You could start by adding the following configurations

    permit same-security-traffic intra-interface

    This will allow traffic to the VPN users access the interface ' outside ' of the SAA and to leave to the Internet using the same interface ' outside '. Without the above command, it is not possible.

    Also, you need to add a NAT configuration for VPN Client users can use the Internet connection of the ASA

    To do this, you can add this command

    NAT (outside) 1 172.16.0.0 255.255.0.0

    This will allow the PAT for the Pool of VPN dynamics.

    Hope this helps

    Don't forget to mark the reply as the answer if it answered your question.

    Ask more if necessary

    -Jouni

  • RVL200 SSL VPN: cannot access a remote LAN with iPad2

    RVL200 firmware 1.1.12.1

    iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.

    Is there another App needed? Or how to debug SSL VPN?

    Emmanuel,

    Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.

  • ASA5500 - anyconnect VPN not access Web server in DMZ

    I am at a loss. I enclose my config. I can access DMZ from within the network, but cannot access DMZ of VPN.

    Any help would be great.

    Rich

    Also have question access to management 0/0 (192.168.1.1) of the Interior of the E0/1 (192.168.2.0) network

    @richyanni1 ,

    For your VPN - DMZ problem, the following is the most likely cause of your problem:

    nat (inside,dmz) source static obj-dmz obj-dmz destination static obj-vpnpool obj-vpnpool
    You should have in place:
    nat (outside,dmz) source static obj-vpnpool obj-vpnpool static obj-dmz obj-dmz
    That's because VPN clients appear to come from the outside (to some purposes NAT) and the need to be exempt from NAT to access the resources of the DMZ. Management problems, the problem is asymmetric routing. When your packages arrive on the management UI, the ASA will try to send back traffic (starting with the 3-way TCP transfer protocol which will fail) through the inside interface but that won't work because ASA helped him, the source of the acknowledgement of receipt would SAA within the interface IP address, not the address of interface management in which the SYN sent. That's why most of the people have not historically used the management interface to ASA unless you have a real out-of-band network for management. Cisco recently introduced a separate fair management routing table, but you need to switch to 9.5 (1) or later to take advantage of that.
  • Create odbc connection between local access and remote access or sql remote

    I need to connect to a remote access or sql database using my local in access 2007 version.  I can't understand what I put in each of the available boxes.  I see only a SQL driver to the system section of the odbc Wizard.  If I decide that he wants to know where the sql server is... well, it's not local, I have a web address for this and may not know how to get the systΦme can recognize the information remotely.  Help, please!

    Means of access:

    http://answers.Microsoft.com/en-us/Office/default.aspx

    Office at the above link forums

    http://social.answers.Microsoft.com/forums/en-us/addbuz

    Access support at the link above.

    They will help you with your questions of access when repost you in the Office Forums above.

    See you soon.

    Mick Murphy - Microsoft partner

  • AnyConnect VPN users cannot access remote subnets?

    I googled this until blue in the face without result.  I don't understand why Cisco this so difficult?  When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices.  What should I do to allow my anyconnect vpn clients access to my remote sites?

    Cisco 5510 8.4

    Hello

    What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.

    In addition to routing, you must have configured for each remote site and the VPN pool NAT0

    Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this

    object-group network to REMOTE SITES

    object-network 10.10.10.0 255.255.255.0

    object-network 10.10.20.0 255.255.255.0

    object-network 10.10.30.0 255.255.255.0

    object-network 10.10.40.0 255.255.255.0

    network of the VPN-POOL object

    10.10.224.0 subnet 255.255.255.0

    NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL

    The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.

    Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.

    My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)

    Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?

    -Jouni

  • AnyConnect VPN full tunnel could not access the site to site VPN

    I have a set of AnyConnect VPN upward with no split tunneling (U-turning/crossed traffic), running 8.2.5 code.

    It works fine, but I want to allow customers to AnyConnect VPN site to site, which I was unable to access.

    I checked the IP addresses of network anyconnect are part of the tunnel on both sides.

    My logic tells me that I must not turn back traffic from the network anyconnect for the site to site VPN, but I don't know how to do this.

    Any help would be appreciated.

    Here are the relevant parts of my config:

    (Domestic network is 192.168.0.0/24,

    the AnyConnect network is 192.168.10.0/24,

    site to site VPN network is 192.168.2.0/24)

    --------------------------------------------------------------------------------------

    permit same-security-traffic inter-interface
    permit same-security-traffic intra-interface

    the DM_INLINE_NETWORK_1 object-group network
    object-network 192.168.0.0 255.255.255.0
    object-network 192.168.10.0 255.255.255.0
    inside_nat0_outbound list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
    permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.10.0 255.255.255.0

    outside_1_cryptomap list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0

    mask 192.168.10.2 - 192.168.10.254 255.255.255.0 IP local pool AnyConnectPool
    Global 1 interface (outside)
    NAT (inside) 0-list of access inside_nat0_outbound
    NAT (inside) 1 0.0.0.0 0.0.0.0
    NAT (outside) 1 192.168.10.0 255.255.255.0
    access-outside group access component software snap-in interface outside
    Route outside 0.0.0.0 0.0.0.0 (the gateway IP) 1
    WebVPN
    allow outside
    AnyConnect essentials
    SVC disk0:/anyconnect-win-3.1.05152-k9.pkg 1 image
    SVC profiles AnyConnectProfile disk0: / anyconnect_client.xml
    enable SVC
    tunnel-group-list activate
    internal AnyConnectGrpPolicy group strategy
    attributes of Group Policy AnyConnectGrpPolicy
    WINS server no
    value of 192.168.0.33 DNS server 192.168.2.33
    VPN-session-timeout no
    Protocol-tunnel-VPN l2tp ipsec svc
    Split-tunnel-policy tunnelall
    the address value AnyConnectPool pools
    type tunnel-group AnyConnectGroup remote access
    attributes global-tunnel-group AnyConnectGroup
    address pool AnyConnectPool
    authentication-server-group SERVER1_AD
    Group Policy - by default-AnyConnectGrpPolicy
    tunnel-group AnyConnectGroup webvpn-attributes
    the aaa authentication certificate
    activation of the Group _AnyConnect alias

    Your dial-up VPN traffic as originating apears on the external interface, so I think you need to exonerate NAT pool PN traffic directed to the site to site VPN. Something like this:

     global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 nat (outside) 0 access-list outside_nat0 nat (outside) 1 192.168.10.0 255.255.255.0 access-list outside_nat0 extended permit ip any 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0

  • AnyConnect VPN client can be used for IPSec remote access VPN connection?

    I think I heard it somewhere that AnyConnect VPN can be used for connections SSLvpn IPSec VPN. Is this possible? Thank you!

    No, the Anyconnect software cannot be used to establish the framework for a VPN IPSEC IKE.

  • Cannot access remote network by VPN Site to Site ASA

    Hello everyone

    First of all I must say that I have configured the VPN site-to site a million times before.  Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks

    ASA local:
    hostname gyd - asa
    domain bct.az
    activate the encrypted password of XeY1QWHKPK75Y48j
    XeY1QWHKPK75Y48j encrypted passwd
    names of
    DNS-guard
    !
    interface GigabitEthernet0/0
    Shutdown
    nameif vpnswc
    security-level 0
    IP 10.254.17.41 255.255.255.248
    !
    interface GigabitEthernet0/1
    Vpn-turan-Baku description
    nameif outside Baku
    security-level 0
    IP 10.254.17.9 255.255.255.248

    !
    interface GigabitEthernet0/2
    Vpn-ganja description
    nameif outside-Ganja
    security-level 0
    IP 10.254.17.17 255.255.255.248
    !
    interface GigabitEthernet0/2.30
    Description remote access
    VLAN 30
    nameif remote access
    security-level 0
    IP 85.*. *. * 255.255.255.0
    !
    interface GigabitEthernet0/3
    Description BCT_Inside
    nameif inside-Bct
    security-level 100
    IP 10.40.50.65 255.255.255.252
    !
    interface Management0/0
    nameif management
    security-level 100
    IP 192.168.251.1 255.255.255.0
    management only
    !
    boot system Disk0: / asa823 - k8.bin
    passive FTP mode
    DNS server-group DefaultDNS
    name-server 192.168.1.3
    domain bct.az
    permit same-security-traffic intra-interface
    object-group network obj - 192.168.121.0
    object-group network obj - 10.40.60.0
    object-group network obj - 10.40.50.0
    object-group network obj - 192.168.0.0
    object-group network obj - 172.26.0.0
    object-group network obj - 10.254.17.0
    object-group network obj - 192.168.122.0
    object-group service obj-tcp-eq-22
    object-group network obj - 10.254.17.18
    object-group network obj - 10.254.17.10
    object-group network obj - 10.254.17.26
    access-list 110 scope ip allow a whole
    NAT list extended access permit tcp any host 10.254.17.10 eq ssh
    NAT list extended access permit tcp any host 10.254.17.26 eq ssh
    access-list extended ip allowed any one sheep
    icmp_inside list extended access permit icmp any one
    icmp_inside of access allowed any ip an extended list
    access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
    RDP list extended access permit tcp any host 192.168.45.3 eq 3389
    rdp extended permitted any one ip access list
    sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
    NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
    NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
    NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
    access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
    access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
    access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
    access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
    access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
    GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
    Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
    azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
    permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
    permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
    pager lines 24
    Enable logging
    emblem of logging
    recording of debug console
    recording of debug trap
    asdm of logging of information
    Interior-Bct 192.168.1.27 host connection
    flow-export destination inside-Bct 192.168.1.27 9996
    vpnswc MTU 1500
    outside Baku MTU 1500
    outside-Ganja MTU 1500
    MTU 1500 remote access
    Interior-Bct MTU 1500
    management of MTU 1500
    IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
    IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    ICMP allow any outside Baku
    ICMP allow access remotely
    ICMP allow any interior-Bct
    ASDM image disk0: / asdm - 621.bin
    don't allow no asdm history
    ARP timeout 14400
    global (outside-Baku) 1 interface
    global (outside-Ganja) interface 2
    3 overall (RAS) interface
    azans access-list NAT 3 (outside-Ganja)
    NAT (remote access) 0 access-list sheep-vpn-city
    NAT 3 list nat-vpn-internet access (remote access)
    NAT (inside-Bct) 0-list of access inside_nat0_outbound
    NAT (inside-Bct) 2-nat-ganja access list
    NAT (inside-Bct) 1 access list nat
    Access-group rdp on interface outside-Ganja
    !
    Router eigrp 2008
    No Auto-resume
    neighbor 10.254.17.10 interface outside Baku
    neighbor 10.40.50.66 Interior-Bct interface
    Network 10.40.50.64 255.255.255.252
    Network 10.250.25.0 255.255.255.0
    Network 10.254.17.8 255.255.255.248
    Network 10.254.17.16 255.255.255.248
    redistribute static
    !
    Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
    Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
    Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
    Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
    Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
    Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
    Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
    Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
    Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
    Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
    Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
    Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
    Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
    Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
    Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
    Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
    Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
    Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
    Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    AAA-server protocol Ganymede GANYMEDE +.
    AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
    key *.
    AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
    key *.
    RADIUS protocol AAA-server TACACS1
    AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
    key *.
    AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
    key *.
    authentication AAA ssh console LOCAL GANYMEDE
    Console to enable AAA authentication RADIUS LOCAL
    Console Telnet AAA authentication RADIUS LOCAL
    AAA accounting ssh console GANYMEDE
    Console Telnet accounting AAA GANYMEDE
    Enable http server
    http 192.168.1.0 255.255.255.0 management
    http 192.168.1.0 255.255.255.0 Interior-Bct
    http 192.168.139.0 255.255.255.0 Interior-Bct
    http 192.168.0.0 255.255.255.0 Interior-Bct
    Survey community SNMP-server host inside-Bct 192.168.1.27
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
    Crypto ipsec transform-set newset aes - esp esp-md5-hmac
    Crypto ipsec transform-set esp-3des esp-sha-hmac myset2

    Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
    Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
    Crypto ipsec transform-set vpnclienttrans transport mode
    life crypto ipsec security association seconds 2147483646
    Crypto ipsec kilobytes of life security-association 2147483646
    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
    correspondence address card crypto mymap 10 110
    card crypto mymap 10 peers set 10.254.17.10

    card crypto mymap 10 transform-set RIGHT
    correspondence address card crypto mymap 20 110
    card crypto mymap 20 peers set 10.254.17.11
    mymap 20 transform-set myset2 crypto card
    card crypto mymap interface outside Baku
    correspondence address card crypto ganja 10 110
    10 ganja crypto map peer set 10.254.17.18
    card crypto ganja 10 transform-set RIGHT
    card crypto interface outside-Ganja ganja
    correspondence address card crypto vpntest 20 110
    peer set card crypto vpntest 20 10.250.25.1
    newset vpntest 20 transform-set card crypto
    card crypto vpntest interface vpnswc
    vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
    card crypto interface for remote access vpnclientmap
    Crypto ca trustpoint ASDM_TrustPoint0
    registration auto
    name of the object CN = gyd - asa .az .bct
    sslvpnkeypair key pair
    Configure CRL
    map of crypto DefaultCertificateMap 10 ca certificate

    crypto isakmp identity address
    ISAKMP crypto enable vpnswc
    ISAKMP crypto enable outside-Baku
    ISAKMP crypto enable outside-Ganja
    crypto ISAKMP enable remote access
    ISAKMP crypto enable Interior-Bct
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    md5 hash
    Group 2
    life 86400
    crypto ISAKMP policy 20
    preshared authentication
    aes encryption
    md5 hash
    Group 2
    life 86400
    crypto ISAKMP policy 30
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 40
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    Crypto isakmp nat-traversal 30
    No vpn-addr-assign aaa
    Telnet timeout 5
    SSH 192.168.0.0 255.255.255.0 Interior-Bct
    SSH timeout 35
    Console timeout 0
    priority queue outside Baku
    queue-limit 2046
    TX-ring-limit 254
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    Server NTP 192.168.1.3
    SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
    SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
    SSL-trust ASDM_TrustPoint0 remote access point
    WebVPN
    turn on remote access
    SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
    enable SVC
    tunnel-group-list activate
    attributes of Group Policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
    internal group ssl policy
    attributes of group ssl policy
    banner welcome to SW value
    value of DNS-server 192.168.1.3
    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
    group-lock value SSL
    WebVPN
    value of the SPS URL-list
    internal vpn group policy
    attributes of vpn group policy
    value of DNS-server 192.168.1.3
    Protocol-tunnel-VPN IPSec l2tp ipsec
    disable the PFS
    BCT.AZ value by default-field
    ssl VPN-group-strategy
    WebVPN
    value of the SPS URL-list
    IPSec-attributes tunnel-group DefaultL2LGroup
    ISAKMP retry threshold 20 keepalive 5
    attributes global-tunnel-group DefaultRAGroup
    raccess address pool
    Group-RADIUS authentication server
    Group Policy - by default-vpn
    IPSec-attributes tunnel-group DefaultRAGroup
    pre-shared key *.
    ISAKMP retry threshold 20 keepalive 5
    IPSec-attributes tunnel-group DefaultWEBVPNGroup
    ISAKMP retry threshold 20 keepalive 5
    tunnel-group 10.254.17.10 type ipsec-l2l
    IPSec-attributes tunnel-group 10.254.17.10
    pre-shared key *.
    ISAKMP retry threshold 20 keepalive 5
    type SSL tunnel-group remote access
    attributes global-group-tunnel SSL
    ssl address pool
    Authentication (remote access) LOCAL servers group
    Group Policy - by default-ssl
    certificate-use-set-name username
    Group-tunnel SSL webvpn-attributes
    enable SSL group-alias
    Group-url https://85. *. *. * / activate
    tunnel-group 10.254.17.18 type ipsec-l2l
    IPSec-attributes tunnel-group 10.254.17.18
    pre-shared key *.
    ISAKMP retry threshold 20 keepalive 5
    tunnel-group 10.254.17.11 type ipsec-l2l
    IPSec-attributes tunnel-group 10.254.17.11
    pre-shared key *.

    ISAKMP retry threshold 20 keepalive 5
    type tunnel-group DefaultSWITGroup remote access
    attributes global-tunnel-group DefaultSWITGroup
    raccess address pool
    Group-RADIUS authentication server
    Group Policy - by default-vpn
    IPSec-attributes tunnel-group DefaultSWITGroup
    pre-shared key *.
    !
    type of policy-card inspect dns migrated_dns_map_1
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the migrated_dns_map_1 dns
    inspect the rsh
    inspect the rtsp
    inspect sqlnet
    inspect sunrpc
    inspect xdmcp
    inspect the netbios
    Review the ip options
    class flow_export_cl
    flow-export-type of event all the destination 192.168.1.27
    class class by default
    flow-export-type of event all the destination 192.168.1.27
    Policy-map Voicepolicy
    class voice
    priority
    The class data
    police release 80000000
    !
    global service-policy global_policy
    service-policy interface outside Baku Voicepolicy
    context of prompt hostname

    Cryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
    : end
    GYD - asa #.

    ASA remote:
    ASA Version 8.2 (3)
    !
    ciscoasa hostname
    activate the encrypted password of XeY1QWHKPK75Y48j
    2KFQnbNIdI.2KYOU encrypted passwd
    names of
    DNS-guard
    !
    interface Ethernet0/0
    nameif inside
    security-level 100
    IP 192.168.80.14 255.255.255.0

    !
    interface Ethernet0/1
    nameif outside
    security-level 0
    IP 10.254.17.11 255.255.255.248

    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    Shutdown
    nameif management
    security-level 100
    no ip address
    management only
    !
    boot system Disk0: / asa823 - k8.bin
    passive FTP mode
    access-list 110 scope ip allow a whole
    192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0

    pager lines 24
    Enable logging
    asdm of logging of information
    Outside 1500 MTU
    management of MTU 1500
    Within 1500 MTU
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    ICMP allow all outside
    ICMP allow any inside
    ASDM image disk0: / asdm - 621.bin
    don't allow no asdm history
    ARP timeout 14400
    NAT (inside) 0 access-list sheep
    Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    Enable http server
    http 192.168.1.0 255.255.255.0 management
    http 192.168.80.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
    Crypto ipsec transform-set newset aes - esp esp-md5-hmac
    Crypto ipsec transform-set esp-3des esp-sha-hmac myset2

    life crypto ipsec security association seconds 2147483646
    Crypto ipsec kilobytes of life security-association 2147483646
    correspondence address card crypto mymap 10 110
    card crypto mymap 10 peers set 10.254.17.9
    mymap 10 transform-set myset2 crypto card
    mymap outside crypto map interface
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10

    preshared authentication
    3des encryption
    md5 hash
    Group 2
    life 86400
    crypto ISAKMP policy 20
    preshared authentication
    aes encryption
    md5 hash
    Group 2
    life 86400
    crypto ISAKMP policy 30
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 40
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    WebVPN

    tunnel-group 10.254.17.9 type ipsec-l2l
    IPSec-attributes tunnel-group 10.254.17.9
    pre-shared key *.

    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns migrated_dns_map_1
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the migrated_dns_map_1 dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    !
    global service-policy global_policy
    context of prompt hostname

    Cryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
    : end
    ciscoasa # $

    Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas

    Would appreciate any help. Thank you in advance...

    If the tunnel is up (phase 1), but no traffic passing the best test is the following:

    Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.

    inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside

    The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).

    Test on both directions.

    Please post the results.

    Federico.

  • Urgent! Users of remote access VPN connects but cannot access remote LAN (ping, folder,...)

    Hello

    I am setting up a VPN on a Cisco ASA 5510 version 8.4 remote access (4) 1.

    When I try to connect via the Cisco VPN client software, I am able to connect however I am unable to access network resources.

    However, I can ping the servers in the other site that is connected through the VPN site-to site to the main site!

    VPN client--> main site (ping times on)--> Site connected with the main site with VPN S2S (successful ping)

    Please help me I need to find a solution as soon as POSSIBLE!

    Thank you in advance.

    Hello

    Please remove the NAT exemption and the re - issue the command but with #1, so it will place the NAT as first line:

    No nat (SERVERS, external) static source SERVERS_LAN SERVERS_LAN NETWORK_OBJ_10.10.40.8_29 NETWORK_OBJ_10.10.40.8_29 non-proxy-arp-search of route static destination

    NAT (SERVERS, external) 1 static source SERVERS_LAN SERVERS_LAN NETWORK_OBJ_10.10.40.8_29 NETWORK_OBJ_10.10.40.8_29 non-proxy-arp-search of route static destination

    After re-configured this way, make sure that this command is also available:

    Sysopt connection permit VPN

    This sysopt will allow traffic regardles any ACL a fall, just in case. Please continue to run a package tracer and post it here,

    Packet-trace entry Server icmp XXXXXX 8 0 detailed YYYYY

    XXXX--> server IP

    AAAA--> VPN IP of the user

    Don't forget to do the two steps and a just in case, capture Please note and mark it as correct the useful message!

    Thank you

    David Castro,

  • Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

    I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

    Thank you

    interface Ethernet0/0

    Speed 100

    full duplex

    nameif outside

    security-level 0

    IP x.x.x.x 255.255.255.240

    !

    interface Ethernet0/1

    Speed 100

    full duplex

    nameif inside

    security-level 100

    IP 10.88.10.254 255.255.255.0

    !

    interface Management0/0

    Shutdown

    nameif management

    security-level 0

    no ip address

    !

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    network of the PAT_to_Outside_ClassA object

    10.88.0.0 subnet 255.255.0.0

    network of the PAT_to_Outside_ClassB object

    subnet 172.16.0.0 255.240.0.0

    network of the PAT_to_Outside_ClassC object

    Subnet 192.168.0.0 255.255.240.0

    network of the LocalNetwork object

    10.88.0.0 subnet 255.255.0.0

    network of the RemoteNetwork1 object

    Subnet 192.168.0.0 255.255.0.0

    network of the RemoteNetwork2 object

    172.16.10.0 subnet 255.255.255.0

    network of the RemoteNetwork3 object

    10.86.0.0 subnet 255.255.0.0

    network of the RemoteNetwork4 object

    10.250.1.0 subnet 255.255.255.0

    network of the NatExempt object

    10.88.10.0 subnet 255.255.255.0

    the Site_to_SiteVPN1 object-group network

    object-network 192.168.4.0 255.255.254.0

    object-network 172.16.10.0 255.255.255.0

    object-network 10.0.0.0 255.0.0.0

    outside_access_in deny ip extended access list a whole

    inside_access_in of access allowed any ip an extended list

    11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

    outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

    mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

    NAT static NatExempt NatExempt of the source (indoor, outdoor)

    NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

    NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

    !

    network of the PAT_to_Outside_ClassA object

    NAT dynamic interface (indoor, outdoor)

    network of the PAT_to_Outside_ClassB object

    NAT dynamic interface (indoor, outdoor)

    network of the PAT_to_Outside_ClassC object

    NAT dynamic interface (indoor, outdoor)

    Access-group outside_access_in in interface outside

    inside_access_in access to the interface inside group

    Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

    dynamic-access-policy-registration DfltAccessPolicy

    Sysopt connection timewait

    Service resetoutside

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto-map dynamic dynmap 10 set pfs

    Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

    life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

    Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

    Crypto-map dynamic dynmap 10 the value reverse-road

    card crypto mymap 1 match address outside_1_cryptomap

    card crypto mymap 1 set counterpart x.x.x.x

    card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

    card crypto mymap 86400 seconds, 1 lifetime of security association set

    map mymap 1 set security-association life crypto kilobytes 4608000

    map mymap 100-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    crypto isakmp identity address

    Crypto isakmp nat-traversal 30

    Crypto ikev1 allow outside

    IKEv1 crypto ipsec-over-tcp port 10000

    IKEv1 crypto policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 1

    life 86400

    IKEv1 crypto policy 50

    preshared authentication

    the Encryption

    md5 hash

    Group 2

    life 86400

    IKEv1 crypto policy 60

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 70

    preshared authentication

    aes-256 encryption

    sha hash

    Group 1

    life 86400

    IKEv1 crypto policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal BACKDOORVPN group policy

    BACKDOORVPN group policy attributes

    value of VPN-filter 11

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelall

    BH.UK value by default-field

    type tunnel-group BACKDOORVPN remote access

    attributes global-tunnel-group BACKDOORVPN

    address pool Admin_Pool

    Group Policy - by default-BACKDOORVPN

    IPSec-attributes tunnel-group BACKDOORVPN

    IKEv1 pre-shared-key *.

    tunnel-group x.x.x.x type ipsec-l2l

    tunnel-group ipsec-attributes x.x.x.x

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    Excellent.

    Evaluate the useful ticket.

    Thank you

    Rizwan James

  • remote VPN and vpn site to site vpn remote users unable to access the local network

    As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

    The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

    ASA Version 8.2 (2)
    !
    host name
    domain kunchevrolet
    activate r8xwsBuKsSP7kABz encrypted password
    r8xwsBuKsSP7kABz encrypted passwd
    names of
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    PPPoE client vpdn group dataone
    IP address pppoe
    !
    interface Ethernet0/1
    nameif inside
    security-level 50
    IP 192.168.215.2 255.255.255.0
    !
    interface Ethernet0/2
    nameif Internet
    security-level 0
    IP address dhcp setroute
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    Shutdown
    No nameif
    no level of security
    no ip address
    management only
    !
    passive FTP mode
    clock timezone IST 5 30
    DNS server-group DefaultDNS
    domain kunchevrolet
    permit same-security-traffic intra-interface
    object-group network GM-DC-VPN-Gateway
    object-group, net-LAN
    access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
    192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
    tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
    pager lines 24
    Enable logging
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    MTU 1500 Internet
    IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
    ICMP unreachable rate-limit 1 burst-size 1
    enable ASDM history
    ARP timeout 14400
    NAT-control
    Global 1 interface (outside)
    NAT (inside) 1 0.0.0.0 0.0.0.0
    Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    the ssh LOCAL console AAA authentication
    AAA authentication LOCAL telnet console
    AAA authentication http LOCAL console
    AAA authentication enable LOCAL console
    LOCAL AAA authentication serial console
    Enable http server
    x.x.x.x 255.255.255.252 out http
    http 192.168.215.0 255.255.255.252 inside
    http 192.168.215.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    Crypto-map dynamic dynmap 65500 transform-set RIGHT
    card crypto 10 VPN ipsec-isakmp dynamic dynmap
    card crypto VPN outside interface
    card crypto 10 ASA-01 set peer 221.135.138.130
    card crypto 10 ASA - 01 the transform-set RIGHT value
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 65535
    preshared authentication
    the Encryption
    sha hash
    Group 2
    lifetime 28800
    Telnet 192.168.215.0 255.255.255.0 inside
    Telnet timeout 5
    SSH 0.0.0.0 0.0.0.0 outdoors
    SSH timeout 5
    Console timeout 0
    management-access inside
    VPDN group dataone request dialout pppoe
    VPDN group dataone localname bb4027654187_scdrid
    VPDN group dataone ppp authentication chap
    VPDN username bb4027654187_scdrid password * local store
    interface for identifying DHCP-client Internet customer
    dhcpd dns 218.248.255.141 218.248.245.1
    !
    dhcpd address 192.168.215.11 - 192.168.215.254 inside
    dhcpd allow inside
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    Des-sha1 encryption SSL
    WebVPN
    allow outside
    tunnel-group-list activate
    internal kun group policy
    kun group policy attributes
    VPN - connections 8
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value split tunnel
    kunchevrolet value by default-field
    test P4ttSyrm33SV8TYp encrypted password username
    username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
    username kunauto attributes
    Strategy Group-VPN-kun
    Protocol-tunnel-VPN IPSec
    tunnel-group vpngroup type remote access
    tunnel-group vpngroup General attributes
    address pool VPN_Users
    Group Policy - by default-kun
    tunnel-group vpngroup webvpn-attributes
    the vpngroup group alias activation
    vpngroup group tunnel ipsec-attributes
    pre-shared key *.
    type tunnel-group test remote access
    tunnel-group x.x.x.x type ipsec-l2l
    tunnel-group ipsec-attributes x.x.x.x
    pre-shared key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    Review the ip options
    inspect the netbios
    inspect the rsh
    inspect the rtsp
    inspect the skinny
    inspect esmtp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect the sip
    inspect xdmcp
    inspect the icmp
    !
    global service-policy global_policy
    context of prompt hostname
    call-home
    Profile of CiscoTAC-1
    no active account
    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
    email address of destination [email protected] / * /
    destination-mode http transport
    Subscribe to alert-group diagnosis
    Subscribe to alert-group environment
    Subscribe to alert-group monthly periodic inventory
    monthly periodicals to subscribe to alert-group configuration
    daily periodic subscribe to alert-group telemetry
    Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
    : end
    kunauto #.

    Hello

    Looking at the configuration, there is an access list this nat exemption: -.

    192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

    But it is not applied in the States of nat.

    Send the following command to the nat exemption to apply: -.

    NAT (inside) 0 access-list sheep

    Kind regards

    Dinesh Moudgil

    P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

  • Help with 1921 SRI Easy VPN remote w / Easy VPN Site-to-Site access

    I have two 1921 ISR routers configured with easy site to site VPN.  I configured VPN each ISR ACL so that all networks on each site can communicate with the private networks of the other site.   I have a 1921 SRI also configured as an easy VPN server.

    Problem: when a remote user connects to the easy VPN server, the user can only access private networks on the site of the VPN server.  I added the IP network that is used for remote users (i.e. the Easy VPN Server IP pool) to each VPN ACL 1921, but the remote user still cannot access other sites private network via the VPN site to another and vice versa.

    Problem: I also have a problem with the easy VPN server, do not place a static host route in its routing table when he established a remote connection to the remote user and provides the remote user with an IP address of the VPN server's IP pool.  The VPN server does not perform this task the first time the user connects.  If the user disconnects and reconnects the router VPN Server does not have the static host route in its routing table for the new IP address given on the later connection.

    Any help is appreciated.

    THX,

    Greg

    Hello Greg,.

    The ASAs require the "same-security-traffic intra-interface permits" to allow through traffic but routers allow traversed by default (is there no need for equivalent command).

    Therefore, VPN clients can access A LAN but can't access the Remote LAN B on the Site to Site.

    You have added the pool of the VPN client to the ACL for the interesting site to Site traffic.

    You must also add the Remote LAN B to the ACL of tunneling split for VPN clients (assuming you are using split tunneling).

    In other words, the VPN router configuration has for customers VPN should allow remote control B LAN in the traffic that is allowed for the VPN clients.

    You can check the above and do the following test:

    1. try to connect to the remote VPN the B. LAN client

    2. check the "sh cry ips his" for the connection of the VPN client and check if there is a surveillance society being built between the pool and Remote LAN B.

    Federico.

  • Refuse the remote user VPN to access PC using VPN from Site users to partner Site

    Hi Experts,

    Installation program:

    We have configured IPSEC Site - Site VPN between Cisco ASA 5510 and Sonicwall.

    Tunnel is in place and working well, we are able to access the remote workstation to partner and Vis Versa.


    Requirment: We want to deny remote VPN users, who are our partners access to the workstation.

    Example:

    Remote IP address range: 192.168.200.x/2r4

    Local IP address range: 192.168.10.x/24

    Deny traffic from 192.168.200.x/24 to 192.168.10.x/24

    Thanks in advance

    Kiran Kumar CH

    Hi Kiran,

    You want to deny certain IP addresses of the Remote LAN (of the L2L tunnel), to connect to your workstation?

    Thus, if the remote network 192.168.200.0/24, want to deny some of these machines to connect to 192.168.10.x?

    If this is the case, you can create ACL VPN (VPN filters) on the SAA to restrictive traffic through the tunnel from the IPs.

    Please clarify if I have misunderstood.

    Federico.

  • 2 VPN SITE to SITE with ACCESS REMOTE VPN

    Hello

    I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration

    Concerning

    Thus, on the routers will be:

    Cisco 2611:

    LAN: 10.10.10.0/24

    access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255

    access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL

    !

    10 ipsec-isakmp crypto map clientmap

    defined by peer 172.18.124.199

    match address 100

    !

    IP local pool ippool 14.1.1.1 14.1.1.254

    !

    access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255

    access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE

    !

    crypto ISAKMP client configuration group ra-customer

        pool ippool

    ACL 120

    !

    Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.

    HTH,

    Portu.

Maybe you are looking for