AnyConnect VPN setup problem
Hi all, I'm going to have bad configure anyconnect VPN on my router. I'm CCENT pre level and especially followed a tutorial, but feel I'm missing something simple here.
It's a fairly simple installation on a Cisco No. 2851 - faces of a single interface my LAN 192.168.1.0/24, the other has a public IP address.
I created a network 192.168.2.0/24 VPN users, mainly to have phones Android connection of their mobile phone networks, and have access to the servers/security cameras/etc by using their local IP addresses. When my phone connects, it gets an IP address and is connected, but is not communicating with my LAN correctly.
The VPN client can ping 192.168.1.254 (the router's LAN IP) - but not the other devices on the network. However, the devices on my LAN can ping the VPN clients to their address 192.168.2.x.
Here's a copy of my current config, I have reorganized some elements with #s. Also pasted my ip sh road under him. Do not forget that I am a novice, please forgive the hack :)
Router (config) #do sh run
Building configuration...
Current configuration: 5782 bytes
!
! Last modification of the configuration at 02:24:24 UTC Sat Sep 5 2015 by #.
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
host name #.
!
boot-start-marker
boot-end-marker
!
!
enable secret $5 1$ 0 #.
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login local sslvpn
AAA authorization exec default local
!
!
!
!
!
AAA - the id of the joint session
!
!
dot11 syslog
no ip source route
!
!
IP cef
!
DHCP excluded-address 192.168.1.200 IP 192.168.1.254
DHCP excluded-address 192.168.1.1 IP 192.168.1.10
!
pool of dhcp IP LAN
network 192.168.1.0 255.255.255.0
Server DNS 192.168.1.254
by default-router 192.168.1.254
!
!
IP domain name # '.com'
host IP Switch 192.168.1.253
8.8.8.8 IP name-server
block connection-for 2000 tent 4 within 60
connection access silencer-class SSH_MGMT
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!
!
!
!
!
voice-card 0
!
Crypto pki token removal timeout default 0
!
Crypto pki trustpoint TRUSTPOINT-MY
enrollment selfsigned
Serial number
name of the object CN = 117-certificate
crl revocation checking
rsakeypair my-rsa-keys
!
!
MY-TRUSTPOINT crypto pki certificate chain
certificate self-signed 01
##########################
#########################
quit smoking
!
!
license udi pid CISCO2851 sn FTX1026A54Y
# 5 secret username $1$ yv # E9.
# 5 secret username $1$ X0nL ###kO.
!
redundancy
!
!
property intellectual ssh version 2
!
!
!
!
!
!
!
!
interface GigabitEthernet0/0
LAN description
IP 192.168.1.254 255.255.255.0
IP nat inside
No virtual-reassembly in ip
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
WAN description
No dhcp client ip asks tftp-server-address
No dhcp ip client application-domain name
DHCP IP address
IP access-group ACL-WAN_INTERFACE in
no ip redirection
no ip proxy-arp
NAT outside IP
No virtual-reassembly in ip
automatic duplex
automatic speed
No cdp enable
!
interface Serial0/0/0
no ip address
Shutdown
!
interface virtual-Template1
!
local IP 192.168.2.100 WEBVPN-POOL pool 192.168.2.110
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
The dns server IP
IP nat inside source list INSIDE_NAT_ADDRESSES interface GigabitEthernet0/1 overload
!
IP access-list standard INSIDE_NAT_ADDRESSES
permit 192.168.1.0 0.0.0.255
permit 192.168.2.0 0.0.0.255
IP access-list standard SSH_MGMT
permit 192.168.1.0 0.0.0.255
permit 207.210.0.0 0.0.255.255
!
IP extended ACL-WAN_INTERFACE access list
deny udp any any eq snmp
TCP refuse any any eq field
TCP refuse any any eq echo
TCP refuse any any day eq
TCP refuse any any eq chargen
TCP refuse any any eq telnet
TCP refuse any any eq finger
deny udp any any eq field
deny ip 127.0.0.0 0.255.255.255 everything
deny ip 192.168.0.0 0.0.255.255 everything
permit any any eq 443 tcp
allow an ip
!
exploitation forest esm config
NLS RESP-timeout 1
CPD cr id 1
!
!
!
!
!
!
!
control plan
!
!
!
!
profile MGCP default
!
!
!
!
!
access controller
Shutdown
!
!
!
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
exec-timeout 0 0
Synchronous recording
line vty 0 4
exec-timeout 0 0
Synchronous recording
entry ssh transport
line vty 5 15
exec-timeout 0 0
Synchronous recording
entry ssh transport
!
Scheduler allocate 20000 1000
!
Gateway Gateway-WebVPN-Cisco WebVPN
IP interface GigabitEthernet0/1 port 443
SSL rc4 - md5 encryption
SSL trustpoint TRUSTPOINT-MY
development
!
WebVPN install svc flash:/webvpn/anyconnect-linux-3.1.03103-k9.pkg sequence 1
!
WebVPN context Cisco WebVPN
title "Firewall.cx WebVPN - powered by Cisco"
SSL authentication check all
!
list of URLS "rewrite".
!
ACL "ssl - acl.
ip permit 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
Licensing ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
!
login message "Cisco Secure WebVPN"
!
webvpnpolicy political group
functions required svc
filter tunnel ssl - acl
SVC-pool of addresses 'WEBVPN-POOL' netmask 255.255.255.0
generate a new key SVC new-tunnel method
SVC split include 192.168.1.0 255.255.255.0
Group Policy - by default-webvpnpolicy
AAA authentication list sslvpn
Gateway Cisco WebVPN bridge
Max-users 5
development
!
end
Gateway of last resort is #. ###. ###. # network 0.0.0.0
S * 0.0.0.0/0 [254/0] via #. ###. ###.1
(###ISP))) is divided into subnets, subnets 1
S (# #ISP #) [254/0] via (# publicgateway #) GigabitEthernet0/1
###.###.0.0/16 is variably divided into subnets, 2 subnets, 2 masks
C ###.###.###.0/23 is directly connected, GigabitEthernet0/1
The ###.###.###.###/32 is directly connected, GigabitEthernet0/1
192.168.1.0/24 is variably divided into subnets, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
The 192.168.1.254/32 is directly connected, GigabitEthernet0/0
192.168.2.0/32 is divided into subnets, subnets 1
S 192.168.2.100 [0/0] via 0.0.0.0, Virtual Network1
can you try to disable the FW on your internal lan hosts and then try and ping from users of vpn client
Tags: Cisco Security
Similar Questions
-
Cannot type 'functions' without client Anyconnect VPN setup
Hi I am trying set Anyconnect VPN client based on Cisco documents below. There is a command like below. When I typed 'function', I can't enter. Can anyone give me some suggestions? Thank you.
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
WebVPN
functions entry url file-access file-exploration of the mapi port forward files filter entry
HTTP-proxy download automatic citrixhttp://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
ASA-recent versions, it is configured without the keyword "functions":
asa(config-group-policy)# webvpn asa(config-group-webvpn)# ? Group-policy WebVPN commands: ... file-browsing Allow browsing for file servers and shares file-entry Allow user entry of file server names to access filter Configure the name of the webtype access-list ... port-forward Configure the name of the Port Forwarding applet and auto-download options ... url-entry Control the ability of the user to enter any HTTP/HTTPS URL url-list Configure a list of WebVPN servers/URLs
-
Can not type 'url-list' without client Anyconnect VPN setup
Hi I am trying set Anyconnect VPN client based on Cisco documents below. There is a command like below. When I typed 'url-list', I can't enter.
Here is example of Cisco:
WebVPN
allow outside
list of URLS ServerList "WSHAWLAP" cifs://10.2.2.2 1
list of URLS ServerList "FOCUS_SRV_1" https://10.2.2.3 2
list of URLS ServerList "FOCUS_SRV_2" http://10.2.2.4 3Here's my ASA:
VPNFW-70/PRI/Act(config-WebVPN) # url -?
set up the mode commands/options:
URL-block url-url-cache serverMy ASA has no choice of the list of URLs when you type '?
Can anyone give me some suggestions? Thank you.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
Hello
In the 7.x code all customizations without client was included in the running configuration.
However, referring to this document from cisco:- http://goo.gl/XRkrcO, you can see that this command has been deprecated in 8.X ASA codes.The best way to configure the bookmarks will use the ASDM or create them on a server and then bring import them to ASA.
Why we can not create bookmarks CLI?
With the introduction of 8.x many more options have been added, allowing greater flexibility. These new options would make the running configuration passes, so they were moved into separate xml files. Indeed, it eliminated the ability to configure a list of bookmark via the CLI.
For more information on this discussion, please refer to this thread: -.
https://supportforums.Cisco.com/discussion/11010546/how-do-i-create-URL-bookmark-WebVPN-Portal-CLIKind regards
Dinesh MoudgilPS Please rate helpful messages.
-
AnyConnect VPN Setup Assistance
Hello world. I installed a new ASA to replace my current and need a bit of help with installing AnyConnect. I think I have everything set up correctly, until my exceptions NAT I can successfully connect to the ASA via the page without customer and the AnyConnect client, but can't pass the SAA, so I guess its exceptions NAT I was looking at both the ASA_cli.pdf but can't seem to nail down. It is not yet using the ASDM, which I don't usually do for VPN, as easy as asdm 6.1 statement.
On my current ASA, I know that I have an ACL called sheep. For reference, my internal networks is 10.0.x.x, and my ip for VPN users pool is 192.168.2.x.
Any help would be greatly appreciated. Thanks in advance
.
Add DNS and WINS servers to corresponding Anyconnect group policy so that it is possible to clients when they connect. Also, make sure that the servers are accessible when connected via Anyconnect.
-
Hi all
I am trying to connect to my Cisco AnyConnect VPN Client but everytime I try, I get an error (connection attempt failed because the network or pc problem cisco)
Can anyone help me please with this.
Thank you
Zia
What is the local firewall on your computer?
-
Hello friends!
I ve been trying to configure the anyconnect VPN, but I cannot generate the CA, probably I m doing wrong sothing.
To be honest, I Don t know if the problem int this VPN is only what is missing, but is the only thing that I've seen what can be a problem.
Someone knows how to generate the CA in the ASA?
Hi Marcio,
Please follow this link:
https://supportforums.Cisco.com/document/12597006/how-configure-ASA-CA-s...
Do you want authentication certificate based for Anyconnect users?
I'm not sure we really need a CA in this case.
You can try to check this third party link to configure the Anyconnect on SAA basic settings:
http://www.petenetlive.com/kb/article/0000943
Kind regards
Aditya
Please evaluate the useful messages.
-
The anyconnect vpn easy vpn Remote communication problem
Hi team,
I have a problem of communication of the anyconnect vpn easy vpn Remote I´ll explain better below and see the attachment
topology:(1) VPN Tunnel between branch HQ - That´s OK
(2) VPN Tunnel between Client AnyConnect to HQ - that s OKThe idea is that the Anyconnect Client is reaching the local Branch Office network, but has not reached.
Communication is established just when I begin a session (icmp or rdp) branch to the AnyConnect Client,.
in this way, the communication is OK, but just for a few minutes.Could you help me?
Below the IOS version and configurationsASA5505 Version 8.4 (7) 23 (Headquarters)
ASA5505 Version 7.0000 23 (branch)Configuration of the server easy VPN (HQ) *.
Crypto dynamic-map DYNAMIC - map 5 set transform-set ESP-AES-256-SHA ikev1
Crypto card outside-link-2_map 1 ipsec-isakmp DYNAMIC-map Dynamics
Crypto map link-outside-2_map-65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
Crypto map interface outside-link-2_map outside-link-2ACL_EZVPN list standard access allowed 10.0.0.0 255.255.255.0
ACL_EZVPN list standard access allowed 192.168.1.0 255.255.255.0
ACL_EZVPN list standard access allowed 192.168.50.0 255.255.255.0
ACL_EZVPN list standard access allowed 10.10.0.0 255.255.255.0internal EZVPN_GP group policy
EZVPN_GP group policy attributes
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list ACL_EZVPN
allow to NEM
type tunnel-group EZVPN_TG remote access
attributes global-tunnel-group EZVPN_TG
Group Policy - by default-EZVPN_GP
IPSec-attributes tunnel-group EZVPN_TG
IKEv1 pre-shared-key *.object-group network Obj_VPN_anyconnect-local
object-network 192.168.1.0 255.255.255.0
object-network 192.168.15.0 255.255.255.0
object-group network Obj-VPN-anyconnect-remote
object-network 192.168.50.0 255.255.255.0
the NAT_EZVPN_Source object-group network
object-network 192.168.1.0 255.255.255.0
object-network 10.10.0.0 255.255.255.0
the NAT_EZVPN_Destination object-group network
object-network 10.0.0.0 255.255.255.0
destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination staticNAT_EZVPN_Destination no-proxy-arp-search to itinerary
NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destinationNAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route
Configuration VPN AnyConnect (HQ) *.
WebVPN
Select the outside link 2
by default-idle-timeout 60
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect profiles Remote_Connection_for_TS_Users disk0: / remote_connection_for_ts_users.xml
AnyConnect enable
tunnel-group-list activatetunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.15.0 255.255.255.0
tunnel of splitting allowed access list standard 10.0.0.0 255.255.255.0internal clientgroup group policy
attributes of the strategy of group clientgroup
WINS server no
value of server DNS 192.168.1.41
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
ipconnection.com.br value by default-field
WebVPN
AnyConnect Dungeon-Installer installed
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect value Remote_Connection_for_TS_Users type user profiles
AnyConnect ask flawless anyconnecttype tunnel-group sslgroup remote access
tunnel-group sslgroup General-attributes
address vpnpool pool
authentication-server-group DC03
Group Policy - by default-clientgroup
tunnel-group sslgroup webvpn-attributes
enable IPConnection-vpn-anyconnect group-aliasobject-group network Obj_VPN_anyconnect-local
object-network 192.168.1.0 255.255.255.0
object-network 192.168.15.0 255.255.255.0
object-group network Obj-VPN-anyconnect-remote
object-network 192.168.50.0 255.255.255.0
the NAT_EZVPN_Source object-group network
object-network 192.168.1.0 255.255.255.0
object-network 10.10.0.0 255.255.255.0
the NAT_EZVPN_Destination object-group network
object-network 10.0.0.0 255.255.255.0
destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination staticNAT_EZVPN_Destination no-proxy-arp-search to itinerary
NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destinationNAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route
Hello
communication works when you send the traffic of easyvpn derivation because it froms the IPSEC SA to pool local subnet and anyconnect HQ. The SA formed only when the branch initiates the connection as it's dynamic peer connection to HQ ASA.
When there no SA between branch and HQ for this traffic, HQ ASA has no idea on where to send the anyconnect to network traffic.
I hope this explains the cause.
Kind regards
Averroès.
-
Setup for use with Cisco Anyconnect VPN IPsec
So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.
I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.
NOTE: We are still testing this ASA and is not in production.
Any help you can give me is greatly appreciated.
ASA Version 8.4 (2)
!
ASA host name
domain.com domain name
!
interface Ethernet0/0
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 50.1.1.225 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
No nameif
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa842 - k8.bin
passive FTP mode
DNS domain-lookup outside
DNS server-group DefaultDNS
!
permit same-security-traffic intra-interface
!
network of the NETWORK_OBJ_192.168.0.224_27 object
subnet 192.168.0.224 255.255.255.224
!
object-group service VPN
ESP service object
the purpose of the tcp destination eq ssh service
the purpose of the tcp destination eq https service
the purpose of the service udp destination eq 443
the destination eq isakmp udp service object
!
allowed IP extended ip access list a whole
!
mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool
no failover
failover time-out period - 1
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary
!
the object of the LAN network
NAT dynamic interface (indoor, outdoor)
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1
Sysopt noproxyarp inside
Sysopt noproxyarp outdoors
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = ASA
Configure CRL
crypto ca server
Shutdown
string encryption ca ASDM_TrustPoint0 certificates
certificate d2c18c4e
864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105
0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609
02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109
3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e
365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609
02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109
6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2
8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b
37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c
234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782
3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02
03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1
cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc
18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6
beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef
af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398
quit smoking
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 10
Console timeout 0
management-access inside
SSL-trust outside ASDM_TrustPoint0 point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2
AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3
profiles of AnyConnect VPN disk0: / devpn.xml
AnyConnect enable
tunnel-group-list activate
internal VPN group policy
attributes of VPN group policy
value of server WINS 50.1.1.17 50.1.1.18
value of 50.1.1.17 DNS server 50.1.1.18
Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client
digitalextremes.com value by default-field
WebVPN
value of AnyConnect VPN type user profiles
always-on-vpn-profile setting
privilege of xxxxxxxxx encrypted password username administrator 15
VPN1 xxxxxxxxx encrypted password username
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address (inside) VPNPool pool
address pool VPNPool
LOCAL authority-server-group
Group Policy - by default-VPN
VPN Tunnel-group webvpn-attributes
enable VPN group-alias
Group-tunnel VPN ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
class-map ips
corresponds to the IP access list
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
class ips
IPS inline help
class class by default
Statistical accounting of user
I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)
Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.
I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.
As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)
-
Quality of VoIP BOUNCING over AnyConnect VPN problems
Hello:
I'm in the middle of the conversion of our environment of VPN for remote access of the former client VPN Cisco AnyConnect (ver. 3.1.01065) VPN's IPSec. I have a number of beta-testers on the new AnyConnect VPN environment, and we have quality problems of intermittent VoIP (IP Communicator 8.5.3 on remote laptops) with the HQ VPN. While I realize that we miss the calls over the Internet, which is a network of 'better' and can not control the Inernet QoS, the special thing is the VoIP call on the former that ipsec VPN seems to work very well 99% of the time.
I did a series of G.729 calls on the old client IPSec and customer AC, with the same laptop, using the same remote access connection. The "VPN server" for the IPSec VPN is an ASA5520 (8.0 (4)), on a connection of 100 Mbps with plenty of reserve, which runs also firewall services for an office of about 500 people and a small DMZ environment. The VPN server that is handling AnyConnect VPN is a new ASA5515-X (8.6 (1) 2), using the same channel of 100 Mbit/s Internet and running VPN services only. When you call running of tests on the old IPSec VPN, the jitter of appeal is pretty consistent, where jitter ave runs about 10 ms and jitter peak running 30-40ms. On the client ACTS, so that 'good' calls run about the same jitter as the old VPN, called the 'bad' (drops intermittent speaker, sometimes sounds 'mechanized'), which produce about 1 of evey 5 calls, run jitter ave to about 120-150ms and jitter of tip of 300-400 m for info, I don't see no packet loss to talk, just call jitter is through the roof. While in most cases, this could be written off as a "bad Internet connection", on the pretty old VPN tests prove a lot is not the issue.
That said, anyone has an idea why the quality of calls is sometimes wrong via the AnyConnect VPN? Is there pest practices that I can work from, or any settings you can recommend? Thank you.
Well, there are several things in our implementation that could help if possible, although I think you can open the case of the TAC, we saw some strange behaviors.
Things to enable the audit side ASA/SSL:
-DTLS - check if it is enabled and WORK (see the det filter name NAME_HERE anyconnect vpn-sessiondb)
see if the packets are tunneled by the DTLS Protocol not TLS. The datagram transport is much better suited for performance.
-Compression - so we see a lot of deployments with it enabled us say this as much as we can. Compression is for links to bandwidth low latency. In the modern internet, it should be used with caution.
-check the ASP drop table on ASA (fall of claire asp, run the "show asp drop' rest and during the period of low performance monitor.)
-additional recording "class... ssl connection. "can give you greater participation.
-See the proto ssl_np - good starting point count
the list goes on and.
What is important to understand, is that the problem is with the traffic on the wire or from the use of SSL.
Sniffer traces are essential.
M.
-
Cisco 1700 Setup as a hub for Cisco Anyconnect VPN
The complete configuration for the router is attached. Additional configuration includes forwarding port 443 (the two tcp/udp), udp 4500, udp 500 and udp 50 to 192.168.1.20.
Objective: Configure Cisco 1700 router as a VPN server, which a Cisco Anyconnect VPN client in. The VPN server is behind a NAT.
Question 1: The Cisco Anyconnect client pulls its set of configuration of the router? I just need to point to the correct IP address and hit connect and it will do the rest? If not, what additional client side configuration must be done? I noticed, it tries to connect on port 443 to my router, but I don't really know why and I know that my router is not listening on this port, so I know I'm missing something:-D.
Question 2: What are the features specifically include easy vpn server? I am confused as to exactly what it is. From what I can tell when you configure easy vpn server you simply set up a regular VPN.
Question 3: Cisco Easy VPN remote has something to do with Cisco Anyconnect or they are completely distinct?
Sorry for the newbie questions. It's really hard to understand the different systems and features on it and most of the examples I found dealt with the VPN router to router rather than configurations just for computers of end users, but I'll be the first to admit that I am new on this hahaha.
Thanks for your help.
PS: Any comment on the misconfigs are welcome. I'm still trying to understand fully exactly what each command does.
Grant
Grant,
AnyConnect can do SSLVPN or IPsec (with IKEv2), ezvpn is all about IKEv1, it won't work.
There (part 3) customers who will be able to connect to ezvpn, as well as the former customer Cisco VPN, but AC is not.
BTW... it's not 50/UDP, this is IP protocol 50 (or sometimes 51) - ESP (or AH).
You don't have TCP and UDP 443 for IPsec, but you may need them for SSL.
And seriously... series of 1700? Wow, this is a 'retro' kit :-) Support ended 6 years ago.
M.
-
ASA 8.3 - SSL VPN - NAT problem
Need help to find how to configure anyconnect VPN with VPN client using a NAT networking internal.
There are many items on the side - how to disable NAT for vpn pool.
I need to create the gateway VPN to the complex international lnetwork, vpnpool is out of range of regular subnet of that network, so it's going to be questions witout NAT routing.
I so need to vpn clients connected to
be PATed to . The problem is that there is also a dynamic to PAT rule for the ordinary acccess Iternet which translates as 'rules NAT asymmetry... "error. Create two times different NAT rules and moving them on up/down makes no difference. There are also some hidden rules of vpn setup :-(that could not be seen.
V8.3 seems is destroying trust in Cisco firewall...
Thank you.
Stan,
Something like this works for me.
192.168.0.0/24---routeur--172.16.0.0/24 ASA-= cloud = host. (the tunnel he get IP address of 'over' pool, which is also connected to the inside)
BSNs-ASA5520-10 (config) # clear xlate
INFO: 762 xlates deleted
BSNs-ASA5520-10 (config) # sh run nat
NAT (inside, outside) static all of a destination SHARED SHARED static
!
NAT source auto after (indoor, outdoor) dynamic one interface
BSNs-ASA5520-10 (config) # sh run object network
network of the LOCAL_NETWORK object
192.168.0.0 subnet 255.255.255.0
The SHARED object network
172.16.0.0 subnet 255.255.255.0
BSNs-ASA5520-10 (config) # sh run ip local pool
IP local pool ALL 10.0.0.100 - 10.0.0.200
local IP ON 172.16.0.100 pool - 172.16.0.155
BSNs-ASA5520-10 (config) # sh run tunne
BSNs-ASA5520-10 (config) # sh run tunnel-group
attributes global-tunnel-group DefaultWEBVPNGroup
address pool ONIf I get your drift... bypass inside and outside is not really necessary on Cisco equipment as it should work straight out of the box via the proxy arp, but I'm not face or solution providers for remote access.
Marcin
-
Cisco AnyConnect VPN Client maintains reconnection
Hello
We have recently installed an ASA5505 and activated the VPN access.
Two of my colleagues have no problems connecting to the VPN using Cisco AnyConnect VPN Client, but I do.
I am still disconnected after a few seconds with the message:
"A VPN reconnect gave rise to different configuration settings. VPN network interface is to be reset. Applications using the private network may be required to restart. »
Cisco AnyConnect VPN Client Version 2.5.2019
I work with Windows 7 but the same thing happens when I try to connect using my computer that is running Windows Vista.
My colleagues also using Win7
I also tried to disable the Windows Firewall.
Any help would be appreciated.
Best regards
Peter
TAC has been able to solve the problem. For webvpn mtu changed default from 1406 to 1200.
Not sure why 2 other ASAs we work very well otherwise though!
WebVPN
SVC mtu 1200 -
CISCO ANYCONNECT VPN CISCO VPN CLIENT
Hi, I was in the process of configuring cisco anyconnect vpn for ip phones to our local obtained the license for them either, the question that I get is that I already have remote configured cisco connect via the old cisco vpn client.
now, if I activate the anyconnect ssl on the same outside the interface both can exist without conflict or maybe I need to migrate users to install the end customer for anyconnect system software to connect.
I also need help with authentication of certification.
concerning
You can run both VPN at the same time without problems.
However, you should try and migrate everyone to the latest technology Anyconnect SSL anyway.
-
Hello
I have configured AnyConnect VPN with split tunneling, so my internal networks is in the tunnel and get internet directly (not via an internal network).
But we want to access one of the public IP (8.8.8.8) through AnyConnect VPN tunnel.
When we check the capture of packets on an external interface, trying to ping 8.8.8.8 showing the icmp-request package but not get icmp-response packages.
Additional configuration required to access the ip address above by tunnel?
We have activated the below configuration as well.
permit same-security-traffic intra-interface
permit same-security-traffic inter-interface
Please find details of the capture below: 192.168.18.71 is my ip from the pool AnyConnect VPN system.
114 extended access-list allow ip host 192.168.18.71 8.8.8.8
115 extended access-list allow host 8.8.8.8 ip 192.168.18.71output interface of capture within the list of access-114
Capture interface entering inside the access-list 115See the capture of xxx - ASA (config) # outgoing
1: 22:13:24.001800 192.168.18.71 > 8.8.8.8: icmp: echo request
2: 22:13:28.986139 192.168.18.71 > 8.8.8.8: icmp: echo request
3: 22:13:33.970561 192.168.18.71 > 8.8.8.8: icmp: echo request
4: 22:13:38.971156 192.168.18.71 > 8.8.8.8: icmp: echo request
5: 22:13:44.080058 192.168.18.71 > 8.8.8.8: icmp: echo request
5 packs shown
XXX - ASA (config) #.
XXX - ASA (config) #.
XXX - ASA (config) # display incoming capture0 packets captured
0 illustrated package
XXX - ASA (config) # display incoming capture0 packets captured
0 illustrated package
Kindly help us solve the problem.
Thank you and best regards,
Ashok
I like to use the notation NAT object instead. So maybe try:
object network obj-192.168.18.0 nat (outside,outside) dynamic interface
-
Anyconnect VPN management if password password has already expired
Hello
I have ASA Cisco AnyConnect vpn with Microsoft AD ldaps authentication. In the Group of the tunnel, I configured management password (password expire days 14). It works but my testing it seems to be no possible to update the password if it is already expired. No way to solve this problem?
Thank you
Hi, Giuseppe.
Yes, the change of password should work even when he arrived at expiration.
Maybe you can try placing screenshots on the user and the server and make sure that the TCP process is successful when the password has expired.
-Javier-
Maybe you are looking for
-
HP Photosmart C6380 all-in-One printer
Recently my printer mentioned above instead print a copy in accordance with the instructions, the photo tray keeps operating. All I want to do is print an A4. I recently replaced all inks. Can someone tell me what could be the problem? Thank you Ceci
-
Yes, but I can't solve it?
-
HP Officejet Pro 8600 most not recognized on the network
I have a Qwest DSL Modem/router that has 4 ports on the back. I use 1 Port on the DSL Modem/Router to conntect to my NetGear router. I use 2 ports on the router/DSL Modem to connect my printer HP OfficeJet Pro 8600 Plus. I use 3 Port on the DSL Mo
-
SE "WindowsUpdate_800B0100" "WindowsUpdate_dt000" message during Windows update Setup
Original title: Windows 7 update that will not update Have 1 update important update for Windows 7 (KB3138612) Download size: 2.5 MB Update type: Important which is "WindowsUpdate_800B0100" "WindowsUpdate_dt000" I tried to install this 4 times now. O
-
HealthCheck HP does not work...
I have a HP Pavilion a6009n Desktop under Vista. I noticed that the HP HealthCheck program is acting weird and doesn't scan. I touched the "scan" button and it flashes on my screen for half a second, but he don't scan at all. I found a sort of soluti