App of Smart Wi - Fi and Guest Access + Bridge Mode

Similar Questions

• Connect and 4200 in Bridge mode

  Can connect be used when the router is in Bridge mode with FIOS router as the main router? Seems when I try to install that he finds not the 4200. THX!

  Nope.  I doubt if you can use your cisco connect with router E4200, defined as a bridge.

• Mode bridge E4200v2 + guest access: No DHCP IP assigned?

  New E4200v2 2.0.37.  In "Bridge Mode - DHCP" (i.e., Access Point router).  Guest access is enabled & SSID broadcast.  DHCP server is disabled, because my main Sonicwall router that provides related to major network 192.168.1.0.

  PROBLEM = PC Client can see "-comments ' fine SSID and associate with her, BUT PC does NOT receive an address IP DHCP (i.e. 192.168.33.x) so the browser login page never appears and guest access does not work.

  I'm sure it's related to DHCP.  I'm assuming that the E4200 not receives or sends the comments with the PC client DHCP packets.

  I saw guest access works on the old E4200v1 before so I know what it should look like.

  Can anyone suggest any probable cause why my E4200v2 would not be providing comments DHCP addresses in the 192.168.33.0 subnet?

  I don't have that 24 hours until I have to deploy 2 new E4200v2 at a remote site and after that it will be really hard problems because I will not be on this site.

  Thanks in advance for expert advice!

  I think I SOLVED!

  Apparently, you need to ACTIVATE the two SERVER NAT & DHCP on the E4200, * before * you switch to BRIDGE MODE.

  When I did this, access as guest - works great!  Hooray!

  I guess the E4200 needs to use these 2 services that run in the background to give the subnet access as guest & dhcp work assignments, which is a process hidden, once you're in Bridge Mode.

  Wow, Cisco should really have a section of the guide user or KB article about it.  Or at least when you click on Bridge-Mode a little pop-up asking you to ensure that these 2 pre - req for are enabled.

  I'm moving now.

• RV110W access point / bridge mode?

  Hi guys,.

  I have a few questions on RV110W.

  I would like to install wifi on my local network access, I have gateway with wan, web filtering etc. etc.. I just want a good wifi access point.

  So why I want to equip with a RV110W and not a normal access point? It's just my boss want mandatory limitation of the internet access of planning by hours, days ~ ~ and guest access. Another detail, my local network have not all dhcp.

  So, in the first place. Can I plug my lan rj45 on switch of RV110W port for internet by my current gateway?

  If I set the limitation of the internet, has done this job of feature on switch port wireless access?

  If I put the dhcp on RV110W (for example 192.X.X.5 to 192.X.X.10) and I identify the ip address on my other gateway for internet access (filtering fortigate), can I put the dhcp on RV110W only on wifi or it will assign ip on other devices on my LAN?

  Thank you very much!

  Hi Ash, you can connect the RV110W by a switch port to another router.

  Dhcp RV110W is not customizable to the point where you can specific to your other router IP of the gateway.

  If active RV110W dhcp would provide DHCP what accept DHCP.

  You may want to look into WAP121 or WAP321.

  -Tom
  Please mark replied messages useful

• E3200 guest access and phones

  Hi all

  Hoping someone here can help me with this problem.

  I have access as guest enabled on my router (firmware v1.0.4). E3200  Computers / laptops can connect, enter the password and use it very well.

  When I try to get a smartphone connect (tried 2 iPhones, 3 Windows phones and 2 different Android phones), they are able to connect to the network, but even after the opening, a browser, will never get to the "hotel" Cisco, landing page, allowing them to enter the guest access password and connect to.  By checking the connection on the phone settings, I see that they have acquired an IP address from 192.x.x.x correctly

  Specifically, I bought this router so that I would not give my WPA key when people came and wanted to use their phones on my network.

  Has anyone successfully got it works?

  Thanks in advance...

  Ok...  After a lot of messing around and reset the default settings, I finally got to work and can repro the problem at will.

  If the you are in a two router setup and the E3200 isn't the main router (i.e. in bridge mode), guest access will not work for smartphones.  Once I swapped the roles of my two routers (i.e. made the main router E3200), guests for Smartphone access works as expected.

  Don't know if a moderator / owner of the firmware feature reads the forums, but if you do, I consider this a bug.

• Store Windows 8 - I can see the store and apps on it, but I can't access my account or download apps. Help!

  Store Windows 8 - I can see the store and apps on it, but I can't access my account or download apps. Help!

  When I click an app I want to download, there is no button 'install' on the page.

  Then I tried to click on 'my account', 'my applications', 'my preferences', etc, and all I get is this point indirect image that turns on in perpetuity.

  I tried the diagnostics as suggested on the community pages but got no where with it. What should I do?

  Help!

  Hi jojo

  You would not believe what happened.

  The problem got worse. Subsequently, the system refused to even give me a sign on another wifi network other than that I'm a.

  I leave the matter for a few weeks before I turned on the laptop.

  I showed that I needed the Microsoft updates, after which the laptop worked like nothing happened.

  Its a mystery of technology that I will never understand.

  Thanks for your help!

  Cheng

• Preference system, security and confidentiality, accessibility - not working/empty

  Hello

  All of a sudden my system preference, safety and confidentiality, accessibility access list does not work, it is completely empty/Virgin and I can't use + / either. They do nothing. The + tries to add an app and I can select an app via the dialog box, but the window just shows blank after choosing an app. He never adds anything.

  I reboot several times and turned to cycling as nothing will do. I also zapped the PRAM, still nothing. I also used the Onyx to repair permissions and also checked the disk, everything going perfectly.

  The list never used to be empty, there are several apps listed in there, but they are all gone now. It is completely empty.

  I have problems because the apps that were once, now on the list will not work until I have added to the list, but I can't. I would like to buy yet another application that could control this list, but I don't know of any application that does.

  I hope someone has a solution or an idea of what to do because you have lived the same exact situation.

  I am running 10.11.5

  Thank you

  -Doren

  

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Guest access / traffic meter

  I had the AC1900 for a few months and I also use access as a guest.

  I was wondering if it was possible to limit the volume of traffic on the access of the guests?

  No, it is not possible to place any cap bandwidth on guest access.

• Printing error: "Spooler subsystem APP has encountered a problem and needs to close."

  Original title: cannot print to the network printer.__I have a net wifi Windows XP, SP 3 and an IBM laptop.

  Printers seem to be installed (XP has the printer connected via USB) but when I try to print from IBM I get an error as follows:

  "Subsystem spooler APP has encountered a problem and needs to close."

  The printer is a HP Deskjet D2660 and the LAN is configured correctly by using the wizard.

  I also discovered that the print spooler is never started.

  In addition, even when I start the spooler it remains not said during the next time I start up.

  Can anyone help? I've been banging my head for two weeks.

  Salvation;

  Thanks for responding.

  My IBM ThinkPad running XP - Pro

  My computer is a DELL and running XP-Home Edition

  Printer installed on DELL

  I have a WIRELESS LAN installed by the installation wizard. The net works fine except for the printer.

  Every time I start the spooler does not work. If I set the spooler of runing the choice is never registered. the next time I start up, the spooler does not work.

  I finally asked some experts to solve the problem of no access to the network printer. It took them more than 4 hours (for a cost) to make it work. Everything was going well until the next day. The problem is back. My thought is that the register should be updated so it will retain the corrtions.

  I downloaded the MATS_RUN.printing.exe utility. It corrects everything except this message on the Spooler subsystem.

  Any advice you can give me would be greatly appreciated.

• Select "Guest Access" router E1000

  I have a Linksys E1000 router. The firmware is 2.1.00 7 build 30 August 2010. I would like to activate or enable guest access. I had to to 192.168.1.1 and find nothing there any access asked. To the wireless tab, the choices are basic setting wireless, advanced wireless, Wireless MAC filter and setting wireless security. Tfhank you.

  I don't think that cisco connect will mess up the configuration.

  You can change the password if necessary.

  I don't think that lion is currently supported.

• Guest access password!

  I think that when I bought this router, there is a guest access password... Right?  I am such a novice to this if there is I don't know where to find it!  Someone help and thank you!

  Dian

  Did you install Cisco Connect? This is where you can administer the guest account.

• Cannot use guest access

  On a new XAC1900 after the installation of a home network based on IP fixed, with the main computer wired and all other 8 devices connected WiFi and no problem at all, I tried to use guest access.

  I have configured the SSID with the suffix - comments and assigned a password. The SSID of the network is visible on the context of the WiFi but the connection will never be finalized.

  The device of the guest, I checked that the SSID of new comments, within its DHCP system, have not been assigned the 192.168.33.XX expected but one IP address, from 169 etc, which corresponds to a provider (not Italian), other then mine. Of course I can not access or enter any password.

  I contacted the support chat system that was very available, but unable to give a solution.

  I checked the configuration several times and reinstalled the latest firmware, but no result even manually.

  Failure is repetitive and the strange IP DHCP assigned to the Guest device is always the same (even after the days), showing that the data seem to be in the firmware. Also after firmware reinstall (verses 1.1.42.162280).

  I have no more ideas!

  Dear all, first thanks for your help. I finally found the solution. Here's how, for the benefit of third parties.

  When I configured the primary network, as always I posted, several equipment (PC, iOS dev, Iphones, portable computers ipads, etc.), fixed IPs. They were assigned in the numbering according to the IP Address of the default router 192.168.1.1. That's why from 192.168.1.2 to 192.168.1.255. I does not take any care about toggle point control DHCP on the router connectivity, and it remained empty. During today muttering I thought: Let me see if activating only not the DHCP protocol to the main network could stop the DHCP server to the SSID of comments. And that's all!  I had to explicitly enable DHCP in connectivity for the second (one guest) to exploit SSID.

  Once again thank you all

• E3000 - guest access without password

  Hello

  I just installed a new E3000 wireless router and it works fine.

  But I would like to give my guests access Internet without having to enter a password.

  I know how to change the - password of comments, but it requires a minimum 4 digits password.

  Is there a way to remove it?

  Thank you

  N ° there is no way that you can remove. The least we can do is to simplify the password such as 1234 or something.

• E4200: Guest access: no IP address on the routers of the waterfall

  configuration:

  2 wireless routers E4200.

  LAN - LAN connected to a cable.

  Router 1 is connected to the internet and has active DHCP.

  Router 2 is NOT connected to the internet and has disabled DHCP.

  Wireless is enabled on both of them with the same SSID.

  account/guest access is enabled on them.

  It works:

  laptop connects to normal WIFI on Router 1--> internet works (IP: 192.168.1.150)

  laptop connects to normal WIFI on Router 2--> internet works (IP: 192.168.1.150)

  laptop connects to the WIFI router 1--> internet reviews works (after the screen connection in Internet Explorer) (IP: 192.168.33.108)

  It does NOT work

  laptop connects to Router 2--> internet reviews WIFI does NOT work

  --> laptop does she not get an IP address

  ?

  When I connect to the normal Wifi on Router 2, I get an IP address from the DHCP on the Router 1

  But when I do the same with the Router 2 REVIEWS WIFI, it does not request an IP address from the Router 1

  anyone ideas?

  Thank you

  comments network only works if the router is connected with its internet port. You cannot use the network invited on the router cascading with the LAN - LAN configuration.

• Cisco ISE 1.4 - guest access

  Hello world

  We use the ISE 1.4, now, we want to use the guest access ISE Module. I created the user invited on portal of the sponsor. Now, how can I configure authentication and authorization policy? I want to verify the user.

  Thank you.

  Hello! I strongly suggest you check out the videos of laboratory Minutes on access for guests and all the rest too :)

  http://www.labminutes.com/video/sec/ISE

  Give those a try and let us know if you still need help.

  Thank you for evaluating useful messages!