ASA 5540 - cannot ping inside the interface
Hi all. We have recently upgraded PIX to ASA5540 and we saw a strange thing going. In a Word, we can ping the inside interface of the ASA from any beach on our 6500 network (which is connected directly behind the ASA on the inside), but one where our monitoring tools are placed. Inside there is an ACL that allows all of our core networks, but it does not help that the interface is really strange.
In the ASDM, I see messages like this:
ID ICMP echo request: 2004 x.x.x.x y.y.y.y on the inside interface to. I don't think that's the problem, but I could be wrong.
This is also the configuration of the interface VLAN VIRTUAL local area network from which we cannot ping inside the interface we can ping to and since this VLAN and machines without problem. The only problem is ping the inside interface of the ASA.
interface Vlanx
IP x.x.x.x 255.255.255.0
IP broadcast directed to 199
IP accounting output-packets
IP pim sparse - dense mode
route IP cache flow
load-interval 30
Has anyone experiences the problem like this before? Thanks in advance for any help.
Can you post the output of the following on the ASA:-
display the route
And the output of your base layer diverter: -.
show ip route<>
HTH >
Tags: Cisco Security
Similar Questions
-
Cisco ASA 5515 - Anyconnect users can connect to ASA, but cannot ping inside the local IP address
Hello!
I have a 5515 ASA with the configuration below. I have configure the ASA as remote access with anyconnect VPN server, now my problem is that I can connect but I can not ping.
ASA Version 9.1 (1)
!
ASA host name
domain xxx.xx
names of
local pool VPN_CLIENT_POOL 192.168.12.1 - 192.168.12.254 255.255.255.0 IP mask
!
interface GigabitEthernet0/0
nameif inside
security-level 100
192.168.11.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description Interface_to_VPN
nameif outside
security-level 0
IP 111.222.333.444 255.255.255.240
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
192.168.5.1 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
www.ww domain name
permit same-security-traffic intra-interface
the object of the LAN network
subnet 192.168.11.0 255.255.255.0
LAN description
network of the SSLVPN_POOL object
255.255.255.0 subnet 192.168.12.0
VPN_CLIENT_ACL list standard access allowed 192.168.11.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 711.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (exterior, Interior) static source SSLVPN_POOL SSLVPN_POOL static destination LAN LAN
Route outside 0.0.0.0 0.0.0.0 111.222.333.443 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
WebVPN
list of URLS no
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication http LOCAL console
LOCAL AAA authorization exec
Enable http server
http 192.168.5.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint ASDM_TrustPoint5
Terminal registration
E-mail [email protected] / * /
name of the object CN = ASA
address-IP 111.222.333.444
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint6
Terminal registration
domain name full vpn.domain.com
E-mail [email protected] / * /
name of the object CN = vpn.domain.com
address-IP 111.222.333.444
pair of keys sslvpn
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint6 certificates
Telnet timeout 5
SSH 192.168.11.0 255.255.255.0 inside
SSH timeout 30
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
192.168.5.2 management - dhcpd addresses 192.168.5.254
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust outside ASDM_TrustPoint6 point
WebVPN
allow outside
CSD image disk0:/csd_3.5.2008-k9.pkg
AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
internal VPN_CLIENT_POLICY group policy
VPN_CLIENT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - 5 concurrent connections
VPN-session-timeout 480
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
myComp.local value by default-field
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect client of dpd-interval 30
dpd-interval gateway AnyConnect 30
AnyConnect dtls lzs compression
AnyConnect modules value vpngina
value of customization DfltCustomization
internal IT_POLICY group policy
IT_POLICY group policy attributes
WINS server no
value of server DNS 192.168.11.198
VPN - connections 3
VPN-session-timeout 120
Protocol-tunnel-VPN-client ssl clientless ssl
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_CLIENT_ACL
field default value societe.com
the address value VPN_CLIENT_POOL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 20
AnyConnect dtls lzs compression
value of customization DfltCustomization
username vpnuser password PA$ encrypted $WORD
vpnuser username attributes
VPN-group-policy VPN_CLIENT_POLICY
type of remote access service
Username vpnuser2 password PA$ encrypted $W
username vpnuser2 attributes
type of remote access service
username admin password ADMINPA$ $ encrypted privilege 15
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address VPN_CLIENT_POOL pool
Group Policy - by default-VPN_CLIENT_POLICY
VPN Tunnel-group webvpn-attributes
the aaa authentication certificate
enable VPN_to_R group-alias
type tunnel-group IT_PROFILE remote access
attributes global-tunnel-group IT_PROFILE
address VPN_CLIENT_POOL pool
Group Policy - by default-IT_POLICY
tunnel-group IT_PROFILE webvpn-attributes
the aaa authentication certificate
enable IT Group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
: end
Help me please! Thank you!
Hello
Please set ACLs to allow ICMP between these two subnets (192.168.11.0 and 192.168.12.0) and check. It should ping. Let me know if it does not work.
Thank you
swap
-
Not able to ping inside the interface from outside
Hello
I'm trying to stimulate a new network like the diagram of the topology below:
However, I have a problem:
ASA:
I can ping to:
192.168.200.1 (Site_RTR IP, int fa0/1)
192.168.200.2 (ASA vlan interface IP, outside interface)
10.133.95.12 (DC_RTR, int fa0/1)
10.133.200.1 (ASA vlan interface IP, inside the interface)
10.133.200.23 (machine)
The RTR website, I can do a ping to:
10.133.95.12
192.168.200.1
192.168.200.2
10.133.200.23 (machine)
but not
10.133.200.1 (ASA vlan interface IP, inside the interface)
Question 1:
It is possible to access / ping back to this address within the IP Interface from outside?
Question 2:
As all subnets 10.0.0.0/8 will go through the interface on the outside, however for the internet traffic, out thru interfacera outside 2.
I haven't set up any nat, is correct to nat all out for outside2?
NAT (inside outside2) source Dynamics one interface
Thanks for the help.
JJ
Hi JJ,
If you plan doing a ping within the IP address of the interface, while the traffic is coming from any interface other than inside, you won't able to ping inside the IP address of the interface.
This is by design, and you cannot change it by any ACL or other settings.
Thank you
Ishan
Please do not forget to select a correct answer and rate useful posts -
Cannot ping inside the ASA from the inside interface
Don't know what I did wrong... appreciate any help
Here is the page layout
laptop--> cisco 3750 switch--> ASA5505 firewall--> future VPN tunnel
Laptop, switch interface VLAN and inside the ASA are all in the same subnet
Switch and ASA have all interfaces local network VIRTUAL 52 (the subnet in question), except for the external interface
-----------------
This is the problem
laptop getting ip addressing and def GW via DHCP from the firewall
switch and FW can ping each other without problem
FW can't ping, still gets the DHCP scope.
Thank you
Dave
Hello
How did you setup?
The laptop is connected to a port of the 3750 (VLAN 52).
The connection between the 3750 and the SAA is a chest or a link L3?
If the 3750 has a SVI belonging to VLAN52, you can ping from the correct PC? As well as the ASA?
Federico.
-
ASA - upgrade to 8.4, impossible to ping inside the interface via IPSec VPN
We have configured a site 5, site to site VPN scenario. Last week, we have upgraded 2 devices ASA 5505 to 8.4.2. Before the upgrade, our monitoring software would ping the inside interface from remote devices to confirm VPN tunnels were established, as well as the addresses of remote devices and the outside of the ASA. While we were on 8.2, remote equipment successfully ping the inside interface. After that we went to 8.4.2 we can do a ping to this interface. We looked at the newspapers and we see the ICMP traffic that is listed in the newspaper, but the remote equipment does not receive back icmp traffic. We can ping successfully from local hardware interface inside and the external interface of remote devices successfully. In addition, we can ping material behind the two devices in both directions successfully.
We are unable to remotely manage the device through the VPN tunnel
Net is:
ASA #1 inside 10.168.107.1 (running ASA 8.2)
ASA #2 inside 10.168.101.1 (running ASA 8,4)
Server 1 (behind the ASA #1) 10.168.107.34
Server 2 (behind the ASA #2) 10.168.101.14
Can ping server 1 Server 2
Can ping server 1 to 1 of the SAA
Can ping server 2-ASA 2
Can ping server 2 to server 1
Can ping server 2 ASA 1
Can ping ASA 2 ASA 1
can not ping ASA 1 and 2 of the ASA
can not ping server 1 and 2 of the ASA
cannot access the ASA 2 https for management interface, nor can the ASDM software
Here is the config on ASA (attached) 2.
Any thoughts would be appreciated.
Hey Joseph,.
Most likely, you hit this bug:
CSCtr16184 Details of bug
To-the-box traffic switches vpn hosts after upgrade to 8.4.2. Symptom:
After the upgrade of the ASA to 8.4.2 all management traffic to employment (including the)
ICMP/telnet/ssh/ASDM) hosts via the VPN (L2L or remote access VPN) can
fail the IP access address to the administration. Conditionsof :
1. the problem occurs if ASA is on 8.4.2. Not been seen on 8.4.1.
2. the user directly logged in the face of internal interfaces no problem with
ICMP/telnet/ssh/AMPS in their respective interfaces. Workaround:
The problem goes back to a Manual NAT statement that straddles the
address IP-access to the administration. The NAT must have both the
source areas and destination. Add the keyword "research route" at the end of
the statement by NAT solves the problem. Ex:
IP address access to the administration Interface of the ASA is 192.168.1.1. ! Statement by NAT overlapping:
NAT obj destination - 192.168.1.0 obj - 192.168.1.0 Shared source (indoor, outdoor)
VPN-vpn-obj static obj! New declaration:
NAT obj destination - 192.168.1.0 obj - 192.168.1.0 Shared source (indoor, outdoor)
public static obj - vpn vpn-obj-research routeHTH,
Raga
-
Hello
I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.
is hell config please kindly and I would like to know what might happen.
hostname horse
domain evergreen.com
activate 2KFQnbNIdI.2KYOU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
ins-guard
!
interface GigabitEthernet0/0
LAN description
nameif inside
security-level 100
192.168.200.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description CONNECTION_TO_FREEMAN
nameif outside
security-level 0
IP 196.1.1.1 255.255.255.248
!
interface GigabitEthernet0/2
Description CONNECTION_TO_TIGHTMAN
nameif backup
security-level 0
IP 197.1.1.1 255.255.255.248
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
boot system Disk0: / asa844-1 - k8.bin
boot system Disk0: / asa707 - k8.bin
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain green.com
network of the NETWORK_OBJ_192.168.2.0_25 object
Subnet 192.168.2.0 255.255.255.128
network of the NETWORK_OBJ_192.168.202.0_24 object
192.168.202.0 subnet 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
the DM_INLINE_NETWORK_2 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any
access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any
Access extensive list permits all ip a OUTSIDE_IN
gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0
gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
backup of MTU 1500
mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-645 - 206.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
!
network obj_any object
dynamic NAT interface (inside, backup)
Access-group interface inside INSIDE_OUT
Access-group OUTSIDE_IN in interface outside
Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10
Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.200.0 255.255.255.0 inside
http 192.168.202.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
monitor SLA 100
type echo protocol ipIcmpEcho 212.58.244.71 interface outside
Timeout 3000
frequency 5
monitor als 100 calendar life never start-time now
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
backup of crypto backup_map interface card
Crypto ikev1 allow outside
Crypto ikev1 enable backup
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
!
track 10 rtr 100 accessibility
Telnet 192.168.200.0 255.255.255.0 inside
Telnet 192.168.202.0 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.202.0 255.255.255.0 inside
SSH 192.168.200.0 255.255.255.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 15
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntunnel strategy
Group vpntunnel policy attributes
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntunnel_splitTunnelAcl
field default value green.com
internal vpntunnell group policy
attributes of the strategy of group vpntunnell
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl
field default value green.com
Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password
attributes of user name THE
VPN-group-policy gbnlvpn
tunnel-group vpntunnel type remote access
tunnel-group vpntunnel General attributes
address VPNPOOL pool
strategy-group-by default vpntunnel
tunnel-group vpntunnel ipsec-attributes
IKEv1 pre-shared-key *.
type tunnel-group vpntunnell remote access
tunnel-group vpntunnell General-attributes
address VPNPOOL2 pool
Group Policy - by default-vpntunnell
vpntunnell group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565
Hello
1 - Please run these commands:
"crypto isakmp nat-traversal 30.
"crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.
The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.
Please let me know.
Thank you.
-
Ping inside the interface on a Pix 501 from outside the network
All the
I have a Pix 501 firewall at a remote site with an IPSEC tunnel established at HQ. We have an analysis tool which remote sites for us let proactively pings know when a site crashes. I want to set up this ping the inside interface of the Pix tool as I can with 871 routers; However I can't configure the Pix to allow ICMP inside interface. I know by default that the Pix does not allow ICMP to the opposite interface and I was wondering if someone could help me with a configuration that will allow this? I enclose my configuration of the pix!
Thank you
Brian
Hello
By raising the ordering tool, it seems that the 'management-access' command was introduced in version 6.3
I recommend spending at 6.3 If you can.
Federico.
-
Cannot ping inside the vpn client hosts. It's a NAT problem
Hello everyone, I'm running into what seems to be a cause of exclusion with an IOS IPSEC VPN NAT/nat. I can connect to the VPN with cisco IPSEC VPN client, and I am able to authenticate. Once I have authenticate, I'm not able to reach one of the guests inside. Below is my relevant config. Any help would be greatly appreciated.
AAA new-model
!
!
AAA authentication login default local
radius of group AAA authentication login userauthen
AAA authorization exec default local
AAA authorization groupauthor LAN
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group businessVPN
key xxxxxx
DNS 192.168.10.2
business.local field
pool vpnpool
ACL 108
Crypto isakmp VPNclient profile
businessVPN group identity match
client authentication list userauthen
ISAKMP authorization list groupauthor
client configuration address respond
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
Define VPNclient isakmp-profile
market arriere-route
!
!
10 ipsec-isakmp crypto map clientmap Dynamics dynmap
interface Loopback0
IP 10.1.10.2 255.255.255.252
no ip redirection
no ip unreachable
no ip proxy-arp
IP virtual-reassembly
!
Null0 interface
no ip unreachable
!
interface FastEthernet0/0
IP 111.111.111.138 255.255.255.252
IP access-group outside_in in
no ip redirection
no ip unreachable
no ip proxy-arp
NAT outside IP
inspect the outgoing IP outside
IP virtual-reassembly
automatic duplex
automatic speed
clientmap card crypto
!
the integrated-Service-Engine0/0 interface
description Locator is initialized with default IMAP group
IP unnumbered Loopback0
no ip redirection
no ip unreachable
no ip proxy-arp
IP virtual-reassembly
ip address of service-module 10.1.10.1 255.255.255.252
Service-module ip default gateway - 10.1.10.2
interface BVI1
IP 192.168.10.1 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
IP nat inside
IP virtual-reassembly
IP nat inside source static tcp 192.168.10.2 25 interface FastEthernet0/0 25
IP nat inside source static tcp 192.168.10.2 443 interface FastEthernet0/0 443
IP nat inside source static tcp 192.168.10.2 3389 interface FastEthernet0/0 3389
IP nat inside source map route nat interface FastEthernet0/0 overload
nat extended IP access list
deny ip 192.168.10.0 0.0.0.255 192.168.109.0 0.0.0.255
refuse the 10.1.1.0 ip 0.0.0.255 192.168.109.0 0.0.0.255
ip licensing 10.1.1.0 0.0.0.255 any
permit ip 192.168.10.0 0.0.0.255 any
sheep extended IP access list
permit ip 192.168.10.0 0.0.0.255 192.168.109.0 0.0.0.255
ip permit 10.1.10.0 0.0.0.255 192.168.109.0 0.0.0.255
ip licensing 10.1.1.0 0.0.0.255 192.168.109.0 0.0.0.255
outside_in extended IP access list
permit tcp object-group Yes_SMTP host 111.111.111.138 eq smtp
permit any any eq 443 tcp
permit tcp 20.20.20.96 0.0.0.31 host 111.111.111.138 eq 3389
permit tcp 20.20.20.96 0.0.0.31 host 111.111.111.138 eq 22
allow any host 111.111.111.138 esp
allow any host 111.111.111.138 eq isakmp udp
allow any host 111.111.111.138 eq non500-isakmp udp
allow any host 111.111.111.138 ahp
allow accord any host 111.111.111.138
access-list 108 allow ip 192.168.109.0 0.0.0.255 192.168.10.0 0.0.0.255
access-list 108 allow ip 192.168.109.0 0.0.0.255 10.1.1.0 0.0.0.255
access-list 108 allow ip 192.168.109.0 0.0.0.255 10.1.10.0 0.0.0.255
!
!
!
!
route nat allowed 10 map
match ip address nat
1 channel ip bridge
In my view, the acl applied to customer is back. It must allow traffic from the internal network to the pool of customers.
To confirm, you can open the Cisco VPN client statistics (after login) then go in the route Details tab. We should see the networks you should be able to reach the customer. Make sure that the good ones are here.
Kind regards
-
Cannot ping ASA inside the interface via VPN
Hello
I have a scenario with tunel VPN between a router and ASA and can ping subnet behind ASA subnet behind the router (and), but I cannot ping the ASA inside the interface on the VPN tunnel. I need to access the remote location ASDM. How can it be done?
Thanks for your suggestions.
Remi
Hello
You must have the 'inside access management' command configured on the SAA.
If you run a 8.3 software or newer on the SAA, should also look at the configuration 'nat' IF the above command solves your problem
-Jouni
-
Can not handle the ASA inside the interface of Site to Site VPN
Hi all
I was deploying new site to site between ASA 8.0 (HQ) and ASA 8.4 (branch). Everything works fine but I have a problem on the ASA-reach remote that I can't manage branch ASA with inside the interface IP address.
My setup on remote ASA
management-access inside
ICMP allow any inside
SSH 0.0.0.0 0.0.0.0 inside
SNMP-server host inside 10.0.1.101 communitry test-snmp version 2 c
My Test
-ping of the AC for inside the interface of remote ASA
- Client time-out see demand
- When debug icmp on ASA remote then ASA show only ICMP request to HQ no response back from remote ASA
I'm not sure whether it's a bug on ASA 8.4 or not because I can manage a remote other ASA what version 8.0 software HQ
Thanks in advance
Do not know what 8.4 version you use, but it is broken in the 8.4 (2), I stumbled upon the upgrade from same problem. SSH and ASDM will not connect through a VPN L2L interface inside. This worked well in 8.4 (1).
-
try VPN remote ping inside the network
I use this Setup
http://www.Cisco.com/image/gif/en/us/guest/tech/TK372/c1492/ccmigration_09186a008009442e.gif
I cannot ping inside user from the remote client?
do you know why?
Add...
management-access inside
Please evaluate the useful messages.
-
Inside the interface of access IPSec on PIX
Hi all
I need advice with the following problem.
I have PIX 515E with 3 interfaces inside.
DMZ and outside, to 6.3 (3). Is it possible to access DMZ more inside the interface with IPSec of CISCO VPN client? IPSec creates a tunnel, the customer
has a new address of the address pool, but
in the paper, I have a message: not found translation etc... When I try to
reach any device in the DMZ. The reason seems
be with nat (dmz) 0, which should be inside the DMZ (social security social security 50 0). Even if I use nat (dmz) 0-list of remote access apart from it does not work. Any tips?
Thank you
Zdenek
Hello
Can you check if you are able to access the DMZ from the inside? If so, then u shud be able to access DMZ to connect remotely. This is because once the VPN client obtains the IP address of the inside pool, it's as good as he is in your home LAN. You can try putting inside DMZ natting... I mean put this command nat 0 because inside the DMZ, which will allow access to DMZ devices inside.
-
Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
ASA 5512 Anyconnect VPN cannot connect inside the network 9.1 x
Hello
I'm new to ASA, can I please help with this. I managed to connect to the vpn through the mobility cisco anyconnect client, but I am unable to connect to the Internet. the allocated ip address was 172.16.1.60 and it seems OK, I thought my acl and nat is configured to allow and translate the given vpn ip pool but I'm not able to ping anything on the inside.
If anyone can share some light... There's got to be something escapes me...
Here's my sh run
Thank you
Raul
-------------------------------------------------------------------------------
DLSYD - ASA # sh run
: Saved
:
ASA 9.1 Version 2
!
hostname DLSYD - ASA
domain delo.local
activate the encrypted password of UszxwHyGcg.e6o4z
names of
mask 172.16.1.60 - 172.16.1.70 255.255.255.0 IP local pool DLVPN_Pool
!
interface GigabitEthernet0/0
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/1
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/2
Post description
10 speed
full duplex
nameif Ext
security-level 0
IP 125.255.160.54 255.255.255.252
!
interface GigabitEthernet0/3
Description Int
10 speed
full duplex
nameif Int
security-level 100
IP 192.168.255.2 255.255.255.252
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa912-smp - k8.bin
passive FTP mode
clock timezone IS 10
clock daylight saving time EDT recurring last Sun Oct 02:00 last Sun Mar 03:00
DNS lookup field inside
DNS domain-lookup Int
DNS server-group DefaultDNS
192.168.1.90 server name
192.168.1.202 server name
domain delo.local
permit same-security-traffic intra-interface
network dlau40 object
Home 192.168.1.209
network dlausyd02 object
host 192.168.1.202
network of the object 192.168.1.42
host 192.168.1.42
dlau-utm network object
host 192.168.1.50
network dlauxa6 object
Home 192.168.1.62
network of the 192.168.1.93 object
host 192.168.1.93
network dlau-ftp01 object
Home 192.168.1.112
dlau-dlau-ftp01 network object
network dlvpn_network object
subnet 172.16.1.0 255.255.255.0
the object-group Good-ICMP ICMP-type
echo ICMP-object
response to echo ICMP-object
ICMP-object has exceeded the time
Object-ICMP traceroute
ICMP-unreachable object
DLVPN_STAcl list standard access allowed 192.168.0.0 255.255.0.0
Standard access list DLVPN_STAcl allow 196.1.1.0 255.255.255.0
DLVPN_STAcl list standard access allowed 126.0.0.0 255.255.0.0
Ext_access_in access list extended icmp permitted any object-group Good-ICMP
Ext_access_in list extended access permitted tcp dlau-ftp01 eq ftp objects
Ext_access_in list extended access permit tcp any object dlausyd02 eq https
Ext_access_in list extended access permit tcp any object dlau-utm eq smtp
Ext_access_in list extended access permit tcp any object dlauxa6 eq 444
Ext_access_in access-list extended permitted ip object annete-home everything
pager lines 24
Enable logging
asdm of logging of information
MTU 1500 Ext
MTU 1500 Int
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 713.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (Int, Ext) static source any any destination static dlvpn_network dlvpn_network non-proxy-arp
!
network dlausyd02 object
NAT (Int, Ext) interface static tcp https https service
dlau-utm network object
NAT (Int, Ext) interface static tcp smtp smtp service
network dlauxa6 object
NAT (Int, Ext) interface static tcp 444 444 service
network dlau-ftp01 object
NAT (Int, Ext) interface static tcp ftp ftp service
Access-group Ext_access_in in Ext interface
Route Ext 0.0.0.0 0.0.0.0 125.255.160.53 1
Route Int 192.168.0.0 255.255.0.0 192.168.255.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication enable LOCAL console
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
http server enable 44310
http server idle-timeout 30
http 192.168.0.0 255.255.0.0 Int
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
trustpool crypto ca policy
Telnet 192.168.1.0 255.255.255.0 management
Telnet timeout 30
SSH 192.168.0.0 255.255.0.0 Int
SSH timeout 30
SSH group dh-Group1-sha1 key exchange
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 61.8.0.89 prefer external source
SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
WebVPN
port 44320
allow outside
Select Ext
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_DLVPN group strategy
attributes of Group Policy GroupPolicy_DLVPN
WINS server no
value of server DNS 192.168.1.90 192.168.1.202
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DLVPN_STAcl
delonghi.local value by default-field
WebVPN
AnyConnect Dungeon-Installer installed
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect ask flawless anyconnect
encrypted vendor_ipfx pb6/6ZHhaPgDKSHn password username
vendor_pacnet mIHuYi1jcf9OqVN9 encrypted password username
username admin password encrypted tFU2y7Uo15ahFyt4
type tunnel-group DLVPN remote access
attributes global-tunnel-group DLVPN
address pool DLVPN_Pool
Group Policy - by default-GroupPolicy_DLVPN
tunnel-group DLVPN webvpn-attributes
enable DLVPN group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
inspect the ftp
inspect the tftp
!
global service-policy global_policy
SMTPS
Server 192.168.1.50
Group Policy - by default-DfltGrpPolicy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:67aa840d5cfff989bc045172b2d06212
: end
DLSYD - ASA #.Hello
Add just to be sure, the following configurations related to ICMP traffic
Policy-map global_policy
class inspection_default
inspect the icmp
inspect the icmp errorYour NAT0 configurations for traffic between LAN and VPN users seem to. Your Split Tunnel ACL seems fine too because it has included 192.168.0.0/16. I don't know what are the other.
I wonder if this is a test installation since you don't seem to have a dynamic PAT configured for your local network at all. Just a few static PAT and the NAT0 for VPN configurations. If it is a test configuration yet then confirmed that the device behind the ASA in the internal network has a default route pointing to the ASAs interface and if so is it properly configured?
Can you same ICMP the directly behind the ASA which is the gateway to LANs?
If you want to try ICMP interface internal to the VPN ASA then you can add this command and then try ICMP to the internal interface of the ASA
Int Management-access
As the post is a little confusing in the sense that the subject talk on the traffic doesn't work not internal to the network, while the message mentions the traffic to the Internet? I guess you meant only traffic to the local network because you use Split Tunnel VPN, which means that Internet traffic should use the VPN local Internet users while traffic to the networks specified in the ACL Tunnel Split list should be sent to the VPN.
-Jouni
-
ASA 5505 9.1 Unable to ping inside the IPSec VPN network
To give some background that the asa has been reloaded and upgranded from 8.2 to 9.1. I am able to connect to vpn, but unable to reach anything inside, including of the asa. I didn't unfortunately not much experience with 8.3 +, but I thought that I had nat made appropriately. Nothing else is currently configured for the asa, as it's just an asa test currently, so I could of just missed something odvious.
ASA Version 9.1 (3)
!
hostname testasa
activate the encrypted password of Ry5/Pmodu2QL1Xe3
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
names of
mask 192.168.3.1 - 192.168.3.200 255.255.255.0 IP local pool VPNPool
!
interface Ethernet0/0
!
interface Ethernet0/1
switchport access vlan 2
!
interface Ethernet0/2
switchport access vlan 2
!
interface Ethernet0/3
switchport access vlan 2
!
interface Ethernet0/4
switchport access vlan 2
!
interface Ethernet0/5
switchport access vlan 2
!
interface Ethernet0/6
switchport access vlan 2
!
interface Ethernet0/7
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.2.252 255.255.255.0
!
passive FTP mode
network of the NETWORK_OBJ_192.168.2.0_24 object
Subnet 192.168.2.0 255.255.255.0
network of the NETWORK_OBJ_192.168.3.0_24 object
subnet 192.168.3.0 255.255.255.0
network of object obj-Interior
Subnet 192.168.2.0 255.255.255.0
object obj - vpn network
subnet 192.168.3.0 255.255.255.0
VPNGroup_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source inside obj obj-indoor destination static obj - vpn obj - vpn
!
NAT source auto after (indoor, outdoor) dynamic one interface
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.2.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec pmtu aging infinite - the security association
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
trustpool crypto ca policy
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
interface ID client DHCP-client to the outside
dhcpd address 192.168.2.50 - 192.168.2.100 inside
dhcpd dns 208.67.222.222 198.153.192.40 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal VPNGroup group strategy
Group Policy attributes VPNGroup
value of server DNS 208.67.222.222 198.153.192.40
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPNGroup_splitTunnelAcl
disable the split-tunnel-all dns
no method of MSIE-proxy-proxy
VLAN no
NAC settings no
test I9znLlryc6yq.BN4 encrypted privilege 15 password username
tunnel-group VPNGroup type remote access
attributes global-tunnel-group VPNGroup
address pool VPNPool
Group Policy - by default-VPNGroup
IPSec-attributes tunnel-group VPNGroup
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
Hello
To be honest, I can't see anything in the configuration that should be a problem.
Your NAT settings seem to be correct.
You have the global setting of "sysopt connection permit - vpn" who does not appear in this form in the CLI configuration. This configuration means essentially that the SAA would allow traffic from a VPN connection to work around interface ACL of the interface when the VPN connection is completed (outside)
Your ACL Split Tunnel is also correct.
You might connect with VPN Client and run a continuous ICMP to a host of LAN and provide an output of the following command after a the ICMP has run a few seconds
Crypto ipsec to show his
Should see the counters of VPN.
You can also try adding
management-access inside
This should allowed you to the 'internal' to the ASA IP ICMP and also manage ASA through the VPN connection by using the 'internal' the IP address provided you have enabled it. But for this you need to change the configuration of "nat" in this
NAT (inside, outside) static source inside obj obj-indoor destination static obj - vpn vpn-obj-research route
Hope this helps
-Jouni
Maybe you are looking for
-
What application would you recommend if I want to use my ipad as a second monitor for macbook please?
-
My Satellite M40X: DVD Rom has had serious problem
Dear friends, my laptop worked for 3 months without any problem.these days when I put a CD in DVD rom is not recognized and a error message on the screen that says that no cd is in the drive.could would be a software problem or it's definitely a hard
-
Problems of keyb/mouse on A30 - 921 reactions when you play
OK, pretty much since I have received this laptop I had a problem with the keyboard or mouse when you play. Everything works very well, and adults in general unless you're gaming. The keys in the game (say HL, HL2, Quake II, GTA, etc) are used to 'pa
-
HP Deskjet 3070: question HP Deskjet 3070 USB El Capitan
Hello Just bought my new Macbook and try to install the printer with USB (like I did with my previous macbook in Mavericks), I have the choice between 'generic printer PCL' or choose the software, I chose "HP deskjet series", but when I print there i
-
Error loading C:\WINDOWS\urepiliy.dll
Error loading C:\WINDOWS\urepiliy.dll Don't ask me what happened... but now I get this error at startup upward, my task bar icons are gone and my computer keeps freezing upwards! I have Scanner ESET scan malwarebytes, malicious software removal tool