ASA 8.3 - SSL VPN - NAT problem

Similar Questions

• UTM50 SSL VPN IE11 problem

  I use the SSL VPN in time. I just noticed that when I tried to pass by I logged in and tap on connect, but now I get the error: virtual failure of execution of the Passage. I tried another computer that is already running IE9 and I had no problem getting in and using my office remotely over SSL.

  IE11 isn't working? or what should I be looking at.
  router is the latest firmware.

  64-bit is IE only.

  IE10 and 11 are disasters, when it comes to compatibility and how it manages Active-X controls. I'm not aware of any SSL VPN with IE10/11 suppliers.

  You can try Firefox. I can get the java applet to install, but the roads do not work for me.

  Contact support directly and express your concerns.

  You can always use IPsec client software.

• VPN NAT problem

  I was informed by an outside vendor they need me to install a VPN site-to site on our ASA 5510/8, 4.

  I have configured the VPN IPsec site to site, but they have a weird requirement. For some reason, they want me

  NAT the server in question for 172.19.10.1/29, who already like a CARESS to the outside. Then, I would have

  to create a policy NAT who said if 192.168.225.10 needs to access the 172.29.0.0/29 then NAT at 172.29.10.1.

  My only concern is, the only connections on the SAA is the external interface that goes to the WAN, and a

  internal interface that goes to a switch. There is no interface that has 172.29.10.0/29 this partner network.

  I thought you could only NAT to an interface that has an address that is mapped to it.

  The router connected to the ASA will never see that such intellectual property that it is located in the VPN tunnel. Only your IPSec peer sees this and if all goes well, he knows what to do with this address, if he asked that NAT.

  Your NAT should be changed if the remote network is HCAS:

  Static NAT to destination for the FSU HCASNAT static HCAS HCAS source (indoor, outdoor)

  EDIT: This rule should be placed before your General NAT statement, which the ASA addresses the rules high NAT down.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• ASA VPN (NAT problem)?

  Hi people, I was hoping sopmeone on these forums might be able to help. I have some problem with a config for our ASA5510, functioning 8.2 (1)

  I installed a VPN tunnel a firewall to vyatta off-site. The tunnel is up.

  ABN-FW3-CISCO ASA5510 # show crypto ipsec his
  Interface: outside
  Tag crypto map: VPN_Zettagrid_Map, seq num: 10, local addr: 116.212.X.X
  VPN_cryptomap list access ip 192.9.0.0 255.255.0.0 allow 192.168.11.0 255.255.255.0
  local ident (addr, mask, prot, port): (192.9.0.0/255.255.0.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.11.0/255.255.255.0/0/0)
  current_peer: 119.252.X.X
  #pkts program: 14, #pkts encrypt: 14, #pkts digest: 14
  #pkts decaps: 16, #pkts decrypt: 16, #pkts check: 16
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 14, comp #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #send errors: 0, #recv errors: 0
  local crypto endpt. : 116.212.X.X, remote Start crypto. : 119.252.X.X
  Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
  current outbound SPI: 670F3BF5

  Now I can pass information of the 119.252.X.X to our internal networks (192.9.0.0/16) vyatta (yes I know this is a wide audience, but it comes to the environment, I inherited, I'm running with a project to put private network addresses, but its not finished quite yet)

  The problem seems to be information of ASA to the internal network behind the vyatta - 192.168.11.0/24.

  When I check my syslog I get the following error: (this example has been a connection attempt mstsc)
  : Inbound TCP connection deny from 192.9.216.190/60660 to 192.168.11.101/3389 SYN flags on the interface inside

  Now Im guessing this SYN message means that the ASA trying to NAT my outgoing packets... which is strange because I have configured a rule sheep. But when I do a show nat is the result:

  ABN-FW3-CISCO ASA5510 # display nat inside
  is the intellectual property inside 192.9.0.0 outside 192.168.11.0 255.255.0.0 255.255.255.0
  Exempt from NAT
  translate_hits = 0, untranslate_hits = 37 (this value does not change)

  Here is my config for NAT

  Inside_nat0_outbound to access extended list ip 192.9.0.0 255.255.0.0 allow 192.168.11.0 255.255.255.0
  Inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.11.0 255.255.255.0
  Access extensive list ip 192.10.201.0 Inside_nat0_outbound allow 255.255.255.0 192.168.11.0 255.255.255.0

  (I have a separate ACL for interesting traffic)

  VPN_cryptomap to access extended list ip 192.9.0.0 255.255.0.0 allow 192.168.11.0 255.255.255.0

  VPN_cryptomap to access ip 10.0.0.0 scope list allow 255.0.0.0 192.168.11.0 255.255.255.0

  Access extensive list ip 192.10.201.0 VPN_cryptomap allow 255.255.255.0 192.168.11.0 255.255.255.0

  Global 1 interface (outside)
  NAT (inside) 0-list of access Inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  NAT (dmz) 1 172.30.3.0 255.255.255.0
  NAT (management) 1 192.10.201.0 255.255.255.0
  NAT (dmz2) 1 172.30.2.0 255.255.255.0
  static (inside, dmz) 192.9.0.0 192.9.0.0 255.255.0.0 subnet mask

  Im guessing that one of these rules is in conflict? Does nat (inside) 0 Inside_nat0_outbound access list take precedence over the nat (inside) 1 0.0.0.0 0.0.0.0?

  I can post more if necessary config, any help at this point would be much appreciated

  Hmm looks like you establish 192.168.11.0 who seems to be blocked by the ACL on the traffic of 192.9.0.0 inside the interface.

  Please paste config ACL or see if that blocks this traffic.

  Thank you

  Ajay

• SSL VPN using ASA 5520 mode cluster - several problems

  I configured 2 ASA 5520 s in the load balancing cluster mode. I connect using anyconnect and I download the customer the first time and everything works well except outlook. I don't know why outlook does not work.

  The second problem is after the anyconnect client is installed on your machine, he remembers that ASA (say ASA2) he first connected and the GUI shows the address IP of ASA2 instead of the virtual IP address of the cluster. I want users always connect using the virtual IP address.

  The third problem I have is there is a default group of SSL VPN and I want all users to use this group. In the initial web page, there is a drop down menu which shows that this group, but I still want to disable this menu drop-down.

  Any suggestions?

  To disable the drop-down menu, you can turn it off with the command

  WebVPN

  no activation of tunnel-group-list

  This will take care of your last issue.

  ***************************

  You can create a profile of the Anyconnect client with the name of the server you want to connect with and that make the ASA that will solve your problem of virtual IP.

  **************************

  Regarding Outlook, do you use specific ports which allows inspection of the ASA. Take a look at the list of inspection on the SAA and perhaps try to disable inspection and see if it works.

  *****************************

• Installation of SSL VPN problem

  Hi all

  I am setting up a SSL VPN on our ASA 5510 using the Secure Mobility client.  After working through several problems, I was able to get the test server to download and install the Linux client, and he says that it is connected.  When I try to ping any server in the LAN, however, the first ping is responded to and the rest of out time.  On the firewall, I see a stream of errors like this:

  3

  October 11, 2014

  16:12:58

  SRV1

  172.16.40.185

  Refuse icmp incoming outside CBC: SRV1 outside dst: 172.16.40.185 (type 0, code 0)

  split tunneling seems to work fine, I can access the Internet yet, but any attempt to reach a server in the LAN will expire.

  Now I have had this before working with a Windows and a Mac client, but removed this configuration and (I thought) completely recreated when I updated the anyconnect images to include an image of linux.  Now I get this same problem with all 3 platforms.

  Can anyone advise me on what I may be missing or that I can provide to diagnose the problem?

  ASA is running v8.2 (5)

  I followed this guide to set up: http://www.techrepublic.com/blog/data-center/eight-easy-steps-to-cisco-a...

  Thank you!

  Ok thank you.

  If your clients are assigned addresses of:

  mask 172.16.40.185 - 172.16.40.190 255.255.252.0 IP local pool VPNTestPool

  You have exempted from this pool of NAT with the last entry in your acl sheep:

  access-list sheep extended permits all ip 172.16.40.184 255.255.255.248

  A potential problem I see is that the pool is a subnet dug into your internal network:

  IP 172.16.40.2 255.255.252.0

  The ASA believe hosts on this subnet to be connected, and your heart can be confused on the way forward.

  In addition, I don't see where you set the

   sysopt connection permit-vpn

  .. .command recommended in the configuration guide you followed.

  Also. in the first packet - trace, the source for client VPN traffic must be outside, not inside.

• ASA from Site to Site and SSL VPN stop working

  Thanks in advance for any advice

  We have an ASA 5510, users were able to connect via to all connect without any problems. We opened a new office with an ASA 5505 and decided to give VPN site-to-site on IPSec. We used the basic wizard and everything went smoothly at both ends. However, users who always used SSL VPN says so that they can connect to the original site, they are no longer in their RDP virtual machines or get anywhere on the network. I don't know why something like this can happen.

  You can change the SSL VPN DHCP scope to give a different subnet for IP addresses. Maybe try 192.168.10.0 255.255.255.0. Let me know if you can and if that corrects the issue.

  Sent by Cisco Support technique iPhone App

• IP NAT on the router on SSL - VPN appliance

  Someone at - it allows to transmit 443/SSL on a SSL VPN Cisco 891 - K9 unit?

  (I have never encountered this situation before as the router VPN terminated public face directly or we had several IPs public to assign the VPN device directly a public IP address).

  With ' ip nat inside source static tcp 44.55.66.255 443 10.10.10.150 443 extensible "is supposed to pass the SSL request to the appliance SSL VPN to 10.10.10.150 to have VPN applications ended here.

  But failed miserably body 891 - K9 created a virtual ARP entry for 10.10.10.150. So two MACs with the same IP address.

  So 443 requests were sent to its interface. At the hearing of NAT, I can't ssh inside SSL - VPN, but by the time the statemet disappeared, I can ssh and warning dupliacte ARP goes.

  * 1 Nov 19:22:46.871: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
  * 1 Nov 19:23:18.083: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
  * 1 Nov 19:23:48.295: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
  RTR #sh clock
  * 19:24:26.487 UTC Sunday, November 1, 2015
  RTR #sh ip arp 10.10.10.150
  Protocol of age (min) address Addr Type Interface equipment
  Internet 10.10.10.150 - e02f.6d96.8dd0 ARPA Vlan10
  RTR #sh ip arp 10.10.10.150
  Protocol of age (min) address Addr Type Interface equipment
  Internet 10.10.10.150 - e02f.6d96.8dd0 ARPA Vlan10
  RTR #sh sh ip route 10.10.10.150

  Cisco TAC to reproduce this problem at the moment to report dev.

  Does anyone else have this problem or a workaround?

  Thank you.

  I may be misunderstanding but isn't your NAT statement backwards IE. If you want traffic to pass to 10.10.10.150 it shouldn't be-

  ' ip nat inside source static tcp 10.10.10.150 43 43 44.55.66.25x.

  isn't the device for SSL connection on interface 'ip nat inside '?

  Jon

• Cisco ASA AnyConnect SSL VPN - certificates + token?

  Hello

  I'm looking for an answer is it possible such configuration:

  The Cisco AnyConnect SSL VPN service with two-factor - first method is the Microsoft CA certificate local and second method - a token solution Symantec VIP password?

  I don't know if two-factor authentication is user/password from Active Directory + OTP by Symantec VIP there is no problem, because you can send the user + pass with Radius, but with certificates I do not really understand who will check the validity of the certificate, which certificate, we will send you to the RADIUS for the validation server and how the configuration of the point of view of ASA will look like.

  Thank you very much for the help!

  Hi Alex,

  I don't see a problem with having certificate + token to connect to the VPN. Certificate authentication must be performed on the SAA, see an example below:

  https://supportforums.Cisco.com/blog/152941/AnyConnect-certificate-based-authentication

  Authentication token can be specified as primary/secondary (authentication SDI) on the SAA, an example below:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/anyconnect31/Administration/Guide/anyconnectadmin31/ac11authenticate.html#pgfId-1060345

  It may be useful

  -Randy-

• Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)

  Hello Cisco community support,

  I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.

  ISP network gateway: 10.1.10.0/24

  ASA to the router network: 10.1.40.0/30

  Pool DHCP VPN: 10.1.30.0/24

  Network of the range: 10.1.20.0/24

  Development network: 10.1.10.0/24

  : Saved
  :
  : Serial number: FCH18477CPT
  : Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
  :
  ASA 6,0000 Version 1
  !
  hostname ctcndasa01
  activate bcn1WtX5vuf3YzS3 encrypted password
  names of
  cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 10.1.40.1 255.255.255.252
  !
  interface GigabitEthernet0/1
  nameif outside
  security-level 0
  address IP X.X.X.237 255.255.255.248
  !
  interface GigabitEthernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa916-1-smp - k8.bin
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_10.1.30.0_24 object
  10.1.30.0 subnet 255.255.255.0
  network obj_any object
  network obj_10.1.40.0 object
  10.1.40.0 subnet 255.255.255.0
  network obj_10.1.30.0 object
  10.1.30.0 subnet 255.255.255.0
  outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
  FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
  access-list 101 extended allow any4 any4-answer icmp echo
  access-list standard split allow 10.1.40.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
  Access-group outside_access_in in interface outside
  !
  Router eigrp 1
  Network 10.1.10.0 255.255.255.0
  Network 10.1.20.0 255.255.255.0
  Network 10.1.30.0 255.255.255.0
  Network 10.1.40.0 255.255.255.252
  !
  Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  without activating the user identity
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 192.168.1.0 255.255.255.0 inside
  http X.X.X.238 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Crypto ipsec pmtu aging infinite - the security association
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = 10.1.30.254, CN = ctcndasa01
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate c902a155
  308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
  0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
  0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
  170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
  64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
  0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
  9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
  705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
  4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
  3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
  06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
  42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
  fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
  59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
  d8966b50 917a88bb f4f30d82 6f8b58ba 61
  quit smoking
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  VPN-addr-assign local reuse / 360 time
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
  SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
  AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_cnd-vpn group policy
  GroupPolicy_cnd-vpn group policy attributes
  WINS server no
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  by default no
  xxxx GCOh1bma8K1tKZHa username encrypted password
  type tunnel-group cnd - vpn remote access
  tunnel-group global cnd-vpn-attributes
  address-cnd-vpn-dhcp-pool
  strategy-group-by default GroupPolicy_cnd-vpn
  tunnel-group cnd - vpn webvpn-attributes
  activation of the alias group cnd - vpn
  !
  ICMP-class class-map
  match default-inspection-traffic
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map icmp_policy
  icmp category
  inspect the icmp
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  service-policy icmp_policy outside interface
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
  : end
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history

  Can you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?

• SSL VPN - ASA - Active Directory LDAP

  Hello

  Scenario: ASA 8.0 (3) running SSL VPN for remote users. LDAP also authenticates access and connect to the ASA.

  For some reason any (we had a power failure, but the problem may be caused by other reasons as well), I can not connect to the ASA, as my login ID does not work, and remote users get connection error when trying to authenticate via SSL VPN web gui.

  I have rebooted the ASA and AD without any change in the situation. This service worked very well before and the problem happened suddenly. No one has all the changes for the configs. Customer do not have a backup configuration. Any suggestion on what would be the best next action to solve this problem? I'm not expert on the Microsoft LDAP configuration, and if anyone knows where I can check in Microsoft windows server 2003 for the possible LDAP problem, that would be greatly appreciated.

  Thank you

  rdianat

  the ldap bind account is just a normal user account. He didn't need even administrative permissions. If you want to use ldap for password changes he needs to password change permissions, but otherwise just a normal user account - make sure it cannot be locked in AD or the password never expires none of this things. you will see the name of the ldap account in the config of the SAA.

  LDAP-login-password *.

  LDAP-connection-dn *.

• New for mapping SSL VPN ACS ASA - ASA groups

  Greetings,

  I am new to ASA, so any help is greatly appreciated.

  I just installed and installed an ASA 5520. I installed an SSL VPN. What I'm trying to achieve is to configure profiles of different groups and different users can access various resources when they access the VPN.

  Current config-

  ASA 5520 v8.3

  ACS 4.0

  Field of Windwos 2003

  I have different installation profiles in the ASA. (i.e. business Dept.) When I choose in the drop down menu, it allows me to open a session and displays the options I've chosen for this group. The problem is that I can connect in this group with any account. GBA, all windows domain users are in the default group. I guess the default group is being processed and which has hosted and user logon.

  Can anyone provide a good article or tips on how to configure the ASA and the ACS for several groups of users. We have several departments that will have to get the parameters when they connect. The ACS groups are mapped to the Windows groups that correspond to each Department

  Any help is greatly appreciated.

  Thank you

  Tim

  Hello

  I think that you need to activate locking group.

  In order to configure Group locking, send group policy name in the attribute class 25 on the Authentication Dial - In User Service (RADIUS Remote) server and choose the group to lock the user in policy.  For example, to lock the user 123 of Cisco in the RemoteGroup group, define the class of attributes 25 Internet Engineering Task Force (IETF) UO = RemotePolicy; for this user on the RADIUS server.

• SSL VPN from Cisco ASA and ACS 5.1 change password

  Dear Sir.

  I am tring configure ASA to change the local password on ACS 5.1. When the user access with ssl vpn if the ACS 5.1 password expiration date. ASA will display the dialog box or window popup to change the password. But it does not work. I'm tring to Setup with the functionality of password management on the SAA. When I enable password management it will not work and is unable to change the password. Could you tell me about this problem?

  Thank you

  Aphichat

  
  Dear Sir,
  I'm tring to setup ASA to change local password on ACS 5.1. When user access with ssl vpn if password on ACS 5.1 expire. ASA will show dialog box or pop-up to change password. But It don't work. I'm tring to setup with password management feature on ASA . When I enable password management it don't work and can't to change password. Could you advise me about this problem?
  Thank you
  Aphichat
  

  Hi Aphichat,

  Go to the password link below change promt via AEC in ASA: -.

  https://supportforums.Cisco.com/docs/doc-1328;JSESSIONID=A51E68318579261787BD60DDA0707819. Node0

  Hope to help!

  Ganesh.H

  Don't forget to note the useful message

• prevent the SSL VPN user to access ASA cli

  Hello

  I set up multiple users on my ASA in its local database.

  These users are used for the ssl vpn connection, but the problem I have is that users

  also have SSH access. Is it possible to avoid this?

  Thank you

  Hello Raf,

  If you do something like this:

  username xxx attributes

  type of remote access service

  the user should not get access CLI more.

  Kind regards

  Bastien

• site to site vpn with ASA 5500 series SSL?

  We have routers DLink DIR - 130 5505 s ASA and PIXen, all work well with our PIX 515E, we need to replace.

  We also have Internet satellite in two places. High latency makes IPsec VPN to DLinks on these very slow sites.

  We were informed by HughesNet that a SSL VPN will mitigate some of the problems of latency.

  However, we cannot use a VPN client for the biometric timeclocks in these places, the clocks need static IP addresses and are more or less "dumb terminals".

  The machine of series 5000 ASA VPN site to site similar to OpenVPN or only the most comment client-server type SSL VPN connections?

  Thank you, Tom

  Hi Thomas,

  The SSL VPN on ASAs feature is a client/server relationship where the remote computer can connect without client (browser) or clientbased (AnyConnect) to the ASA.

  Federico.