ASA easy vpn server and ios client both need public ip

Similar Questions

• SDM & easy VPN server problem

  I'm having a problem setting up an easy VPN server using Cisco Security

  Device Manager Version 2. 0a on a router in 1711 with IOS 12.3 (7) XR3.

  I have reset the router to the factory defects since the opening screen of SDM.

  Connect to 10.10.10.1

  User: cisco

  Password: Cisco

  Start SDM for the initial router configuration dialog box.

  Don't use CNS

  On basic configuration screen:

  Hostname set to router

  Domain: test.com

  Synchronize time with local PC

  Change the user name

  New user name: root

  password: xyzzy123

  password: xyzzy1234

  The LAN Interface Setup screen

  IP address set to 10.1.1.1

  Subnet: 255.255.255.0

  Active DHCP server

  Start IP: 10.1.1.50

  End IP: 10.1.1.70

  DNS Configuration screen

  Primary: 45.45.45.45

  Secondary: 45.45.45.46

  Use for DHCP Clients

  WAN Configuration screen

  Ethernet selected without Encapsulation PPOE

  No dynamic (DHCP Client) host name

  Advanced options screen

  Selected for VLAN1 port address translation

  After reading the summary, I chose the FINISH. Asked if dialog box I have

  you want to set up a basic firewall, I selected YES. I left all the

  secure by default items selected. I clicked FINISH. SDM detected that the

  DHCP client on the untrusted external interface and asked if I wanted to

  allow DHCP traffic through the firewall. I selected YES. The configuration

  has been delivered.

  Save the running-config startup-config and reloaded the router.

  Released and renewed my ip address and then reconnected in 1711 from new

  user name and password. SDM restarted.

  Has begun the task of configuration and choose to set up an easy VPN server.

  The opening screen had a command prompt to enable AAA. I launched the selected task

  After that the AAA commands have been delivered to the router.

  I chose the interface FastEthernet0 menu drop-down

  IKE proposals - selected default all the

  Transform set - selected default all the

  Group authorization / policy research - Selected Local only

  Add the user name: User1

  Password: local1

  Encrypt with MD5

  Privilege: 2

  Group permission/User Group Policies

  Add political group: tunnel

  Preshared key: sharedkey

  Selected new address Pool: 10.1.1.80 to 10.1.1.90

  Test after you have configured the selected button.

  Exit this screen, there was a warning SDM on the NAT with ACL rules

  have to be converted into NAT rules with course maps. I clicked YES to let

  SDM convert rules.

  Tests successful Easy VPN Server and client screen displays a warning

  on the "crypto ipsec df - bit clear' needing to be defined." He was not a

  way to put it in SDM and the search function had no success.

  I copied the running-config to the startup-config and tested the router from a

  connect remotely using a different ISP.

  The results:

  The SDM monitor shows the client connection, but the client cannot ping

  any host on the LAN of the router. No one on the LAN can easy ping of VPN client

  Assigned IP of VPN, but they can ping the client using the asigned IP ISP

  address.

  It seems that SDM not correctly configures the 1711 to route of the

  VPN interface to the local network.

  I enclose my 1711 Running Configuration generated by SDM.

  Hello

  I think that the reason why the ping is not successful is that your LAN IP address (connected to the VLAN interface) and the pool of IP addresses assigned to the client are in the same network.

  You can try assigning a pool of IP addresses for VPn clients that is in another subnet (say 10.1.2.80 to 10.1.2.90) and then try to ping?

  You can change the pool by means of configure-> additional tasks-> local swimming pools.

  You can then disconnect the client on the Monitoring page and connect again.

  Kind regards

  Ravikumar

• ASA VPN server and vpn client router 871

  Hi all

  I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.

  any suggestions would be much appreciated.

  Thank you

  Alex

  Do "crypto ipsec client ezvpn show ' on 871, does say:

  ...

  Save password: refused

  ...

  ezVPN server dictates the client if it can automatically connect with saved password.

  Set "enable password storage" under the group policy on the ASA.

  Kind regards

  Roman

• IOS Easy VPN Server / Radius attributes

  Hello

  I made an easy VPN server installation with a running 12.2 2621XM router (15) output T5. VPN Clients/users are authenticated against Cisco ACS 3.2 by RADIUS.

  It works fine, but there is a problem that I can't solve. Each user must have the same VPN assigned IP address whenever it is authenticated.

  The ACS sends the right radius attribute (box-IP-Address) back to square of IOS, but this address is not assigned to the client. The customer always gets the next available IP address in the local set on the router.

  How can I solve this problem?

  You will find the relevant parts of the configuration and a RADIUS "deb" below.

  Kind regards

  Christian

  AAA - password password:

  AAA authentication calls username username:

  RADIUS AAA authentication login local users group

  RADIUS AAA authorization network default local group

  crypto ISAKMP policy 1

  Group 2

  !

  crypto ISAKMP policy 3

  md5 hash

  preshared authentication

  Group 2

  ISAKMP crypto identity hostname

  !

  ISAKMP crypto client configuration group kh_vpn

  mypreshared key

  pool mypool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac shades

  !

  mode crypto dynamic-map 1

  shades of transform-set Set

  !

  users list card crypto mode client authentication

  card crypto isakmp authorization list by default mode

  card crypto client mode configuration address respond

  dynamic mode 1-isakmp ipsec crypto map mode

  !

  interface FastEthernet0/1

  IP 192.168.100.41 255.255.255.248

  crypto map mode

  !

  IP local pool mypool 172.16.0.2 172.16.0.10!

  Server RADIUS attribute 8 include-in-access-req

  RADIUS-server host 192.168.100.13 key auth-port 1645 acct-port 1646 XXXXXXXXXXXXXXXX

  RADIUS server authorization allowed missing Type of service

  deb RADIUS #.

  00:03:28: RADIUS: Pick NAS IP for you = tableid 0x83547CDC = 0 cfg_addr = 0.0.0.0 best_a

  DDR = 192.168.100.26

  00:03:28: RADIUS: ustruct sharecount = 2

  00:03:28: RADIUS: success of radius_port_info() = 0 radius_nas_port = 1

  00:03:28: RADIUS (00000000): send request to access the id 192.168.100.13:1645 21645.

  4, len 73

  00:03:28: RADIUS: authenticator 89 EA 97 56 12 B1 C5 C2 - C0 66 59 47 F7 88 96

  68

  00:03:28: RADIUS: NAS-IP-Address [4] 6 192.168.100.26

  00:03:28: RADIUS: NAS-Port-Type [61] Async 6 [0]

  00:03:28: RADIUS: username [1] 10 "vpnuser1".

  00:03:28: RADIUS: Calling-Station-Id [31] 13 "10.1.14.150".

  00:03:28: RADIUS: User-Password [2] 18 *.

  00:03:28: RADIUS: receipt of 192.168.100.13:1645, Access-Accept, id 21645/4 l

  in 108

  00:03:28: RADIUS: authenticator C1 7 29 56 50 89 35 B7 - 92 7 b 1 has 32 87 15 6

  A4

  00:03:28: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:28: RADIUS: connection-ip-addr-host [14] 6 255.255.255.255

  00:03:28: RADIUS: Tunnel-Type [64] 6 01:ESP [9]

  00:03:28: RADIUS: Tunnel-Password [69] 21 *.

  00:03:28: RAY: box-IP-Netmask [9] 6 255.255.255.0

  00:03:28: RADIUS: Framed-IP-Address [8] 6 172.16.0.5

  00:03:28: RADIUS: [25] the class 37

  00:03:28: RADIUS: 43 49 53 43 4F 41 43 53 3 A 30 30 30 30 30 31 30 [CISCOACS:0

  000010]

  00:03:28: RADIUS: 2F 33 63 30 61 38 36 34 31 61 76 70 75 73 [3/c0a8641a 6F 2F

  /vpnus]

  00:03:28: RADIUS: 65 72 31 [1]

  00:03:28: RADIUS: saved the authorization for user 83547CDC to 83548430 data

  00:03:29: RADIUS: authentication for data of the author

  00:03:29: RADIUS: Pick NAS IP for you = tableid 0x82A279FC = 0 cfg_addr = 0.0.0.0 best_a

  DDR = 192.168.100.26

  00:03:29: RADIUS: ustruct sharecount = 3

  00:03:29: RADIUS: success of radius_port_info() = 0 radius_nas_port = 1

  00:03:29: RADIUS (00000000): send request to access the id 192.168.100.13:1645 21645.

  5, len 77

  00:03:29: RADIUS: authenticator 13 B2 A6 CE BF B5 DA 7th - 7B F0 F6 0b A2 35 60

  E3

  00:03:29: RADIUS: NAS-IP-Address [4] 6 192.168.100.26

  00:03:29: RADIUS: NAS-Port-Type [61] Async 6 [0]

  00:03:29: RADIUS: username [1] 8 'kh_vpn '.

  00:03:29: RADIUS: Calling-Station-Id [31] 13 "10.1.14.150".

  00:03:29: RADIUS: User-Password [2] 18 *.

  00:03:29: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:29: RADIUS: receipt of 192.168.100.13:1645, Access-Accept, id 21645/5 l

  in 94

  00:03:29: RADIUS: authenticator C4 F5 2F C3 EE 56 DA C9 - 05 D6 F5 5 d EF 74 23

  AF

  00:03:29: RADIUS: Type of Service [6] 6 leavers [5]

  00:03:29: RADIUS: connection-ip-addr-host [14] 6 255.255.255.255

  00:03:29: RADIUS: Tunnel-Type [64] 6 01:ESP [9]

  00:03:29: RADIUS: Tunnel-Password [69] 21 *.

  00:03:29: RADIUS: [25] class 35

  00:03:29: RADIUS: 43 49 53 43 4F 41 43 53 3 A 30 30 30 30 30 31 30 [CISCOACS:0

  000010]

  00:03:29: RADIUS: 2F 34 63 30 61 38 36 34 31 61 2F 6 b 5F 68 76 70 [4/c0a8641a

  [/ kh_vp]

  00:03:29: RADIUS: 6 [n]

  00:03:29: RADIUS: saved the authorization for user 82A279FC to 82A27D3C data

  Assignment of an IP address via a server Raidus is currently not supported, even if your Radius Server is through an IP address, the router will ignore it and just assign an IP address from the pool locla. In fact, the pool room is the only way to assign IP addresses currently.

  On the only way to do what you want right now is to create different groups VPN, each reference to a local IP pool with an address in it. Then ask each user connect to the appropriate by their VPN client group.

  Yes, messy, but just try to provide a solution for you.

• Help with the easy VPN server with LDAP

  Hello

  I used to be able to set up our easy VPN server with local authentication.

  But now, I'm trying to use LDAP authentication to match with our policies.

  Can someone help me please to check the config and tell me what is wrong with him?

  My router is a Cisco1941/K9.

  Thank you in advance.

  Ryan

  Current configuration: 5128 bytes
  !
  ! Last configuration change at 13:25:16 UTC Tuesday, August 28, 2012, by admin
  ! NVRAM config update at 05:03:14 UTC Monday, August 27, 2012, by admin
  ! NVRAM config update at 05:03:14 UTC Monday, August 27, 2012, by admin
  version 15.2
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  boot-start-marker
  boot-end-marker
  !
  !
  !
  AAA new-model
  !
  !
  AAA group ASIA-LDAP ldap server
  Server server1.domain.net
  !
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authentication login ASIA-LDAP-AUTHENTIC ldap group ASIA-LDAP
  local VPN_Cisco AAA authorization network
  Group ldap AAA authorization network ASIA-LDAP-ASIA-LDAP group authorization
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  No ipv6 cef
  !
  !
  !
  !
  !
  IP domain name domaine.net
  IP cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  Crypto pki token removal timeout default 0
  !
  Crypto pki trustpoint TP-self-signed-765105936
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 765105936
  revocation checking no
  rsakeypair TP-self-signed-765105936
  !
  !
  TP-self-signed-765105936 crypto pki certificate chain
  certificate self-signed 01
  30820229 30820192 A0030201 02020101 300 D 0609 2A 864886 F70D0101 05050030
  2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
  69666963 37363531 30353933 36301E17 313230 36323630 39323033 0D 6174652D
  355A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
  532D 5365 6C662D53 69676E65 642D 4365 72746966 69636174 652 3736 35313035
  06092A 86 4886F70D 01010105 39333630 819F300D 00308189 02818100 0003818D
  C1B7E661 4893D83A EFE44B76 92BAA71A 6375 854 C 88 D 4533E51A 49791 551D8EF7
  F82E2432 E65B401D 27FE4896 2105B38A CB1908C1 9AE2FC19 8A9393C3 1 B 618390
  EE6CB1CC 5C8B8811 04FA198E 16F3297B 6B15F974 13EE4897 97270547 31 74270
  4590ACA6 68606596 97C5D4D5 462CACA0 CDDAC35A 17415302 CFD4E329 8E7E542D
  02030100 01A 35330 03551 D 13 51300F06 0101FF04 05300301 01FF301F 0603551D
  23041830 1680142E FF686472 569BCCF1 552B 1200 1 060355 5B660F30 D35060DB
  1D0E0416 04142EFF 9BCCF155 68647256 2B1200D3 5060DB5B 660F300D 06092 HAS 86
  01010505 00038181 00558F64 05207 D 35 AA4BD086 4579ACF6 BCF6A851 4886F70D
  1D0EA15B 75DBFA45 E01FBA5C 6F827C42 1A50DD11 8922F1E5 3384B8D8 8DD6C222
  0187E501 82C1C557 8AD3445C A4450241 75D771CF 3A6428A6 7E1FC7E5 8B418E65
  74D265DD 06251C7D 6EF39CE9 3 D FE03F795 692763 AE865885 CFF660A5 4C1FF603
  3AF09B1E 243EA5ED 7E4C30B9 3A
  quit smoking
  license udi pid CISCO1941/K9 sn xxxxxxxxxxx

  ISM HW-module 0
  !
  !
  !
  secret admin user name of privilege 15 5 $1 rVI4$ WIP5x6at0b1Vot5LbdlGN.
  ryan privilege 0 0 pass1234 password username
  !
  redundancy
  !
  !
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  Configuration group customer isakmp crypto VPN_Group1
  xxxxxxxxxxxx key
  DNS 10.127.8.20
  pool SDM_POOL_1
  ACL 100
  netmask 255.255.255.0
  ISAKMP crypto ciscocp-ike-profile-1 profile
  match of group identity VPN_Group1
  authentication of LDAP-ASIA-AUTHENTIC customer list
  whitelist ISAKMP ASIA-LDAP-authorization of THE
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-ESP-3DES-SHA
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  IP 10.127.15.1 255.255.255.0
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  !
  interface GigabitEthernet0/0
  IP xxx.xxx.xxx.xxx 255.255.255.224
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  IP 10.127.31.26 255.255.255.252
  automatic duplex
  automatic speed
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered Loopback0
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  local IP SDM_POOL_1 10.127.20.129 pool 10.127.20.254
  IP forward-Protocol ND
  !
  IP http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
  IP route 10.0.0.0 255.0.0.0 10.127.31.25
  IP route 10.127.20.128 255.255.255.128 GigabitEthernet0/0
  !
  Note access-list 100 category CCP_ACL = 4
  access-list 100 permit ip 10.0.0.0 0.255.255.255 everything
  !
  !
  !
  !
  !
  !
  !
  LDAP attribute-map ASIA-username-map
  user name of card type sAMAccountName
  !
  Server1.domain.NET LDAP server
  IPv4 10.127.8.20
  map attribute username-ASIA-map
  bind authenticates root-dn CN = xxx\, S1234567, OU = Service accounts, OR = Admin, OU = Acc
  DC = domain, DC = net password password1
  base-dn DC = domain, DC = net
  bind authentication-first
  !
  !
  control plan
  !
  !
  !
  Line con 0
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line 67
  no activation-character
  No exec
  preferred no transport
  transport of entry all
  output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  transport telnet entry
  !
  Scheduler allocate 20000 1000
  end

  Router #.

  Ryan,

  It seems that you are facing the question where it is indicated in the section:

  Problems with the help of "authentication bind first" with user-defined attribute maps:

  * Then you are likely to see a failure in your authentication attempt. You will see the error message "Invalid credentials, result code = 49.  The newspapers will look something like the journals below: *.

  Which is the same error you see. Go ahead and replace in your attribute map and test again.

  If you remove the command "bind-first authentication' configuration above, everything will work correctly.

  https://supportforums.Cisco.com/docs/doc-17780

  Tarik Admani
  * Please note the useful messages *.

• Cisco 831 - easy VPN server

  Hello

  I am trying to create an easy VPN server on Cisco 831. When I "test" the easy VPN he said that it tested successfully, but when I try to VPN in the router of the built in Windows XP VPN client, I'm unable to connect.

  Does anyone have recommendations for how to configure easy VPN? I basically just selected all the default options. I was not able to find tutorials in the Cisco online documentation.

  Do I need to have the Cisco VPN client to connect to the Cisco router?

  Other thoughts?

  Your IP address pool you are trying to assign to remote users is part of your local network, which is not the best way to assign the ip address to the VPN Clients, and I've seen a lot of problems in the past were route it not forwards the packets to the client. This allows you to change the POOL of something other than your LAN. E.g. 192.168.1.0/24.

  Also, make sure that you re - configure your 102 ACL accordingly.

  Once you make changes, try to connect again and let me know how it goes.

  Kind regards

  Arul

  * Please note all useful messages *.

• PlayBook & cisco Easy VPN Server 831

  I don't seem to be able to connect to my router 831 cisco easy vpn server is configured by using my Blackberry Playbook.  Looking at the console of the router I can see Debugging but don't know what it means.  I have attached debugging as well as glued my setup, if someone is able to help me at all it would be much appreciated.  Thank you very much.

  Current configuration: 2574 bytes
  !
  version 12.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  router host name
  !
  enable secret 5 $1$ FM71$ y4ejS2icnqX79b9gD92E81
  enable password xxxx
  !
  username privilege 15 password 0 $1$ W1fA CRWS_Ritesh $ o1oSEpa163775446
  username privilege 15 secret 5 shamilton wFLF $1$ $ 8eRxnrrgVHMXXC0bXdEGi1
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  AAA - the id of the joint session
  IP subnet zero
  no ip Routing
  !
  !
  audit of IP notify Journal
  Max-events of po verification IP 100
  No ftp server enable write
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  ISAKMP xauth timeout 15 crypto

  !
  ISAKMP crypto client configuration group ciscogroup
  (deleted) 0 key
  DNS 172.16.60.246 172.16.60.237
  pool SDM_POOL_3
  ACL 100
  Save-password
  include-local-lan
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  crypto dynamic-map SDM_DYNMAP_1 1
  game of transformation-ESP-3DES-SHA
  market arriere-route
  !
  !
  card crypto SDM_CMAP_1 client authentication list ciscocp_vpn_xauth_ml_1
  map SDM_CMAP_1 isakmp authorization list ciscocp_vpn_group_ml_1 crypto
  client configuration address map SDM_CMAP_1 crypto answer
  map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
  !
  !
  !
  !
  interface Ethernet0
  IP 172.16.60.241 255.255.255.0
  IP nat inside
  no ip route cache
  !
  interface Ethernet1
  DHCP IP address
  NAT outside IP
  no ip route cache
  automatic duplex
  map SDM_CMAP_1 crypto
  !
  interface FastEthernet1
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface FastEthernet2
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface FastEthernet3
  no ip address
  Shutdown
  automatic duplex
  automatic speed
  !
  interface FastEthernet4
  no ip address
  automatic duplex
  automatic speed
  !
  local IP SDM_POOL_1 172.16.60.190 pool 172.16.60.199
  pool of local SDM_POOL_2 192.168.1.1 IP 192.168.1.100
  local IP SDM_POOL_3 172.16.61.100 pool 172.16.61.150
  IP nat inside source overload map route SDM_RMAP_1 interface Ethernet1
  IP classless
  !
  IP http server
  no ip http secure server
  !
  Remark SDM_ACL category of access list 1 = 2
  access-list 1 permit 172.16.60.0 0.0.0.255
  Note access-list 100 category CCP_ACL = 4
  access-list 100 permit ip 172.16.60.0 0.0.0.255 any
  public RO SNMP-server community
  Enable SNMP-Server intercepts ATS
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  exec-timeout 120 0
  password xxxxx
  length 0
  !
  max-task-time 5000 Planner
  !
  end

  Stace,

  *Mar  1 06:40:15.258: ISAKMP: transform 1, ESP_AES
  *Mar  1 06:40:15.258: ISAKMP:   attributes in transform:
  *Mar  1 06:40:15.262: ISAKMP:      SA life type in seconds
  *Mar  1 06:40:15.262: ISAKMP:      SA life duration (basic) of 10800
  *Mar  1 06:40:15.262: ISAKMP:      encaps is 61443
  *Mar  1 06:40:15.262: ISAKMP:      key length is 256
  *Mar  1 06:40:15.262: ISAKMP:      authenticator is HMAC-SHA
  *Mar  1 06:40:15.262: ISAKMP (0:14): atts are acceptable.
  *Mar  1 06:40:15.262: ISAKMP (0:14): IPSec policy invalidated proposal
  *Mar  1 06:40:15.262: ISAKMP (0:14): phase 2 SA policy not acceptable! (local 14
  

  The other end offers AES 256 and SHA IPSec transform set.

  While you have configured:

  crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac

  Suggestion:

  Add a new set of transofrm and apply it under crypto map.

  HTH,

  Marcin

• Easy VPN server on 1811 configuration

  I'm trying to configure easy VPN server on my router from 1811 to allow remote users to access resources on our corporate network. I used the wizard to perform the configuration for the easy VPN, but when I test the VPN it fails to check the dependent components. He said to me that AAA authentication, authorization and Global Address Pool are all "not configured." I have configured AAA on MDS under additional tasks, so I don't know where I am going wrong. Any help is greatly appreciated.

  Brandon,

  the below URL - provide almost all the examples of configuration for the 18xx series.

  http://conft.com/en/us/products/ps5853/prod_configuration_examples_list.html

  HTH.

• Easy vpn server issues of Cisco 800 series.

  Hello.

  I want to deploy the easy vpn server on cisco 876 and 877 10 routers and access from a remote location (company headquarters). When I leave the firewall of the router off the vpn server works. When I turn it on it doesn't.

  Although I allow all traffic to my ip for example 80.76.61.158 I can't access the vpn server.

  I tried a place to let the firewall off and it worked fine.

  I use SDM to configure the vpn server. Any ideas what I can do with the cause of firewall I really can't leave it "open."

  Thanks in advance.

  It would be a good idea to paste the configuration of the VPN server to the firewall.

  Kind regards

  Kamal

• Cannot connect to the easy VPN server

  Hi *.

  I have a stupid problem with my easy VPN server. I took the following configuration to configure the VPN: click on

  Successfully, I can ping 192.168.99.1 but when I start AnyConnect (enter this IP address as serveraddress) on my IPhone, it first says that the server certificate is not valid (I ignore because it is self-signed..) and when I press continue it says that no link could be established.

  What can be the problem?

  It is very likely that you have a configured PAT-pool and simply use the Word key "overload" when from your external interface. In this command, you reference an ACL (or an ACL in a road map) where we need to ensure that your VPN-pool in included in the traffic using a NAT.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Easy VPN server

  Hello

  I configured easy VPN server on Cisco 1841 & got a form of address IP VPN hen but unfortunately not able to access private or servers on the local network, address maybe because I can NATing.

  Please advice?

  I have attached the file of Configuration of the router.

  Kind regards

  Alain R.Aljabi

  Hello

  Need to get around the NAT for VPN IP address Pool. Please follow it below URL that explains how to work around NAT (static) with route map. This configuration should get your VPN works.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080094634.shtml

  Kind regards

  Arul

  * Please note the useful messages *.

• LOB compression secure between the server and the client

  Hi all
  According to the doc:

  SecureFiles LOB compression is performed on the server and enables random
  reads and writes to LOB data. Compression utilities on the client, like
  utl_compress, cannot provide random access.

  I don't know about the server and the client model in compression. This means that when has a table with a column of compress instance A and instance B accesses the table, the compression is performed on the server? How to do an instance a server or client, in this context? What he means by "random access"? How can we ensure that if a server is running live?
  
  Best regards
  TA.

  How do with random reading and writing? What is random and write anyway?

  LOB manipulation - see DBMS_LOB. e.g. DBMS_LOB. WRITING, WRITEAPPEND, READING, etc

  You couldn't use these on something that has been compressed to the outside.

• What is a good VPN for Mac and iOS client?

  I want to identify a strong product of VPN for Mac and iOS.  I want something that is easy to install and maintain, and it's effective.

  Thank you

  This depends a lot on what you're trying to accomplish. Can elaborate you on why you think you need?

• ASA easy VPN connection problem

  Hi guys,.

  I configured easy VPN between 5510 and 5505. Every thing seems fine, however, if there is no traffic in the tunnel in the next few hours, I can not initial 5510 5505 (customer) traffic. But if I first traffice 5505, there is no problem.

  Anyone know why?

  Thank you

  Hello

  This is normal behavior, it is part of the easy vpn functionality. The 5505 will act as a remote for the 5510 vpn client. This isn't like a site to site vpn or both ends know the IP address of the remote peer, and so that each peer can initiate the connection, here the 5510 don't know on the network and 5505 IP when it will connect via the easy VPN.

  If you want the tunnel to be put in place at both ends, I would say that you are using a classic site-to-site connection as described here:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/Getting_started/ASA5505/quick/guide/SITESITE.html

  I hope this helps.

  Kind regards
  Bastien

• Ins easy vpn server address Pool

  Hello

  I have? ve a router cisco 1721 with a single card wic adsl.

  This router gives me nat (dmz servers) and internet connection.

  Now, I need to implement with this router a vpn server that is easy to provide the vpn connection to customers who use the software of cisco vpn client 4.8.

  I followed step by step the instructions to turn on the server but when the wizard tells me an address pool... I do not know.

  The router has 2 addresses fastethernet, 192.168.156.253 and 192.168.158.253 (secondary).

  My LAN works whith 192.168.156.x address.

  What will be the address pool?

  Best regards

  heze54

  Edgar,

  Configure the pool of addresses as something different from these two networks, as I said in my previous post.

  IP local pool vpnpool 192.168.3.1 192.168.3.254

  I hope this helps.

  Thank you

  Gilbert\

  The rate of this post!