ASA image upgrade

Similar Questions

• The host has not enough space on the boot partition to store the image upgrade. It takes a minimum of size_in_MB. After the release of space or perform an installation from the CD-ROM.

  Hi everyone, the difficulties in trying to update the Update Manager. ESX4.1 to ESXi5.0

  Error I get is below to correct the scan before update:

  The host has not enough space on the boot partition to store the image upgrade. A minimum of 299MB is necessary. After the release of space or perform an installation from the CD-ROM.

  There is enough space in the local disk

  Size of filesystem used Avail use % mounted on
  / dev/sdd5 4.9 G 1.6 G 3.0 G 35%.
  / dev/sdd2 2.0 G 107 M 1.8 G 6% / var/log
  / dev/CCISS/c0d0p1 99 M 67 M 27 M 72% / Boot
  / dev/CCISS/c0d0p2 4.9 G 1.6 G 3.1 G 34% / esx3-installation
  / dev/CCISS/c0d0p1 99 M 67 M 27 M 72% / esx3-installation/boot
  / dev/CCISS/c0d0p7 2.0 G 101 M 1.8 G 6% / esx3-installation/var/log

  Cannot continue installation due to the lack of space and don't have the option upgrade CD directly (of complicated issues)

  Do you have any suggestions?

  Thank you

  It sounds like this host has already been improved 3.x! In this case you will not be able to upgrade to 5.x using the Manager to update because of the small partition/boot (99 MB).

  to remedy the hosts against a basic upgrade

  ... You cannot use Update Manager to upgrade to 5.0 ESXi host, if the host has upgraded ESX 3.x to ESX 4.x. These hosts have not enough free space in the partition/Boot to support the process of update Update Manager. Use either interactive or scripted upgrade.

  André

• IOS SCP image upgrades by omitting the main Infrastructure 2.1

  Hi I'm under 2.1 IP with all the latest patches and packs, but I can't Image SCP transfers to work.

  When I check the suggested logs of the dashboard of jobs (and jump into the root of the CLI) I see the following:
  [DEVICE]= switch Hostname
  [SWITCH-ADMIN-LOGIN]= login username Level 15 to the switch, same username is used in the work of the device Center
  [FIRST-INF-IP]= first server Infrastructure

  [DEVICE] #archive download-sw... archive download-sw/allow-feature-upgrade

  / Overwrite scp://[SWITCH-ADMIN-LOGIN]@[PRIME-INF-IP]//localdisk/tftp/c3560-ipbaselmk9-tar.122-55.SE9.tar

  Password:

  Password:

  % Authentication failed.

  Could not buffer tarfile... using multiple downloads

  looking at the picture...

  Password:

  Password:

  % Authentication failed.

  % Error opening scp://[SWITCH-ADMIN-LOGIN]@[PRIME-INF-IP]//localdisk/tftp/c3560-ipbaselmk9-tar.122-55.SE9.tar (Permission denied)

  % Error opening flash: update / info (no such file or directory)

  ERROR: Image is not a valid IOS image archive.

  [DEVICE] #.

  It seems that the switch tries to connect to the PI server and download software rather than sending the software to the switch IP.

  I used WinSCP to open the URL, but none of the passwords I know or created works.

  I need SSH in the PI box and create a new account CLI (or account Root CLI) that corresponds to the [SWITCH-ADMIN-LOGIN]switch?

  Kind regards

  Hi rowansakul,

  I've defined permissions specific but put a password of 14 characters for the new user in root cli.

  useradd [new user]

  passwd [new user]

  Then apply the new user and the password in the UI graphics, as shown above.

• Version of the Cisco ASA images.

  Hi all.

  Anyone can check my perception on the differences between these images?

  asa933-7-lfbff-k8. SPA

  asa924-5-smp - K8.bin

  asa924-5 - k8.bin

  I guess that lfbff is for the X 5506 and 5508-X with firepower onboard services.

  What are the supposed to a user of the image of SMP (Symmetric MultiProcessing)? The ASA 5506-X and 5508-X would be able to run the SMP image?

  Witch platforms use the image without any abbreviation?

  Any clarification would be greatly appreciated.

  Concerning

  Hello

  Yes you are right.

  asa933-7-lfbff-k8. SPA - this would be used on active firepower ASA for example 5506-X etc.

  asa924-5-smp - K8.bin - this is used for devices using Multi hearts.

  Anything with "smp" in the file name is only compatible with the X-5500 series. The "smp" means symmetric multiprocessor and requires a multicore processor.

  asa924-5 - k8.bin - it is used for legacy of the ASA using single cores.

  Kind regards

  Aditya

• 1142 standalone image upgrade in light Mode

  Hi all

  I spend 1142 APs stand-alone a lightwheight with WCS, but I can't find the recovery image (c1140-rcvk9xxxxx).

  On the Cisco website > support > download > wireless > ap > 1140, if I click on the standalone link to light Mode upgrade Image, I get an error message "no final version available for downloads.

  Any ideas where to download this file?

  Thank you.

  Manu

  Hello Manu,

  Look under the standard IOS images for a - JA 12.4.21;

  WIRELESS LAN LWAPP RECOVERY                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     c1140-rcvk9w8-tar.124-21a.JA.tar

  He's here for a reason

  See you soon!

  Rob

• APEX 3.2 workload problem image upgrade Vista/Win7

  Homepage of the APEX is missing a few images and "connect" button does not work. I thought I followed the instructions properly for apxldimg.sql... Here is my result:
  
  @D:/apex32/apex/apxldimg.sql D:/apex32.
  
  PL/SQL procedure successfully completed.
  
  PL/SQL procedure successfully completed.
  
  PL/SQL procedure successfully completed.
  
  Validation complete.
  
  Is there anything else I need to do?
  
  Thank you, Scott
  
  Published by: svk1965 on April 22, 2010 04:35

  With the apex zip file that you downloaded, once extracted, you must pass in the path of the folder that contains the extracted folder apex (not the folder that contains the images directory) - at least that's what worked for me.

  Van
  Trent

• Update image ASA

  Need to improve my image of Cisco ASA 5510 of asa821 - k8.bin to asa903 - k8.bin with the following license. Do I have to purchase a new license with upgrade of the image?

  #sh version

  Cisco Adaptive Security Appliance Version 8.2 software (1)

  Version 6.2 Device Manager (1)

  Updated Wednesday, 5 May 09 22:45 by manufacturers

  System image file is "disk0: / asa821 - k8.bin.

  The configuration file to the startup was "startup-config '.

  TMN-5510 294 days 2 hours

  Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz

  Internal ATA Compact Flash, 256 MB

  BIOS Flash M50FW080 @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  Start firmware: CN1000-MC-BOOT - 2.00

  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04

  0: Ext: Ethernet0/0: the address is *.

  1: Ext: Ethernet0/1: address is *.

  2: Ext: Ethernet0/2: address is *.

  3: Ext: Ethernet0/3: address is *.

  4: Ext: Management0/0: address *.

  5: Int: internal-Data0/0: the address is *.

  6: Int: internal-Control0/0: the address is *.

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 100

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes an ASA 5510 Security Plus license.

  Series number:

  Running Activation Key: ****************************************************************************

  Registry configuration is 0x1

  Last modified by enable_15 to the configuration 22:29:35.255 * Friday, April 4, 2014

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Need help

  > Do I need to purchase a new license with upgrade of the image?

  NO.

  But check the:

  1)

  https://supportforums.Cisco.com/document/48646/ASA-83-upgrade-what-you-n...

  (2) to migrate the configuration of 8.21 to 9.03 asking TAC cisco help

• MARCH upgrade path with the ISO Image

  Is it possible to upgrade a box 50 MARCH running 3.44 to 4.22 with an ISO image and not to lose the features that have been added to the configuration? Understand sequential image upgrade procedure, I am less sure to skip a major overhaul by using the much faster method of an ISO image.

  Thank you in advance.

  I don't think you can do an upgrade of the recovery ISO image (I would like to know if you hear otherwise). I have used before and haven't seen such an option. It seems quite well rebuild the system entirely.

  http://www.Cisco.com/en/us/products/ps6241/prod_release_note09186a0080561f57.html#wp1099844

• Update IOS ASA

  Hello Experts,

  I have ASA 5520 with IOS image release 7.0 (7).

  Can I do a straight upgrade to image version 8.4 (5)?

  Thank you.

  But be aware that, after 8.2, the configuration of the firewall is object based. There are important changes you need to know before moving on. I saw some improvements go wrong and a complete reconstruction of the configuration was needed.

  http://www.Cisco.com/en/us/docs/security/ASA/asa83/upgrading/migrating.html

• Impossible to upgrade WSA S370 8.5.3 - 069

  Current version 8.5.3 - 069

  When the upgrade of the computer just fails.

  When the upgrade from the CLI I get the following: "image upgrade is not valid. Please check the settings and try again' and I get an email with the following text: "failed to download and installation of the upgrade image due to: the obvious checksum does not match the real checksum to find tips.» This happens with all the updates available - RAID and AsyncOS.

  I downloaded the manifest files and put them in the local HTTP server, but I have the same result.

  Can you please try again?

• Issue of NAT for ASA running 8.4 (5)

  We have a client who is about to hang an ASA off the coast of the demilitarized zone of our firewall that is running 8.4 (5). This firewall is currently on another part of our network, and NAT will be considerably changed. Now, everything on the client firewall must be coordinated outside for the same thing as the IP model internal, for example like the old "static (inside, outside) 172.16.16.0 172.16.16.0 netm 255.255.255.0" command.

  When I look at the document from Cisco for (conversion) NAT

  ( http://www.cisco.com/en/US/docs/security/asa/asa83/upgrading/migrating.html#wp96828), I see not all conversions between the two. This is not a "nat 0" because users need access to certain hosts inside the firewall of our customers.

  Can someone tell me please in the right direction? Thank you

  Hello

  Lets assume that the following is true

  • The new ASA has 'inside' and 'outside' network/interface only
  • The ASA News should do EVERYTHING NAT 'inside' to 'outside' to any kind of situation traffic (your firewall handles this?)

  Then you can simply have the ASA with absolutely no. NAT configurations. The ASA with new software releases 8.3 and above all automatically passes all traffic through the ASA UNNATED. We use it on a single client and it works very well.

  Please let me know if the above is the case, or can't think of anything else

  -Jouni

• Manage the 5512 ASA with SSH via VPN

  Hello

  We are facing problems with ssh access on our ASA5512 on a Site-2-Site VPN tunnel.

  SSH seems to be implemented properly, because we can login from inside and outside on both Interfaces.

  But when we try to connect the ASA from a remote location with SSH Putty reports a timeout.

  We set up a lot of these configurations with ASA5510 and ASA Image 8.x without any problem, so I guess it must have something to do with the new version of the ASA.

  The value by defect-rsa-key was generated successfully.

  VPN is ok and log viewer shows:

  6

  March 21, 2016

  10:21:44

  302013

  192.168.0.100

  51682

  192.168.1.1

  22

  Built of TCP connections incoming 597903 for outside:192.168.0.100/51682 (192.168.0.100/51682) at inside:192.168.1.1/22 (192.168.1.1/22)

  That's how we set up the configuration:

  the ssh LOCAL console AAA authentication

  SSH 192.168.0.0 255.255.255.0 inside (192.168.0.0 is the remote VPN network)

  management-access inside

  username privilege 15 PASSWORD USER password

  We missed something?

  Thank you

  Best regards

  Dennis

  Hi Dennis,

  The config looks very good.

  Are you able to ping inside the interface through the tunnel.

  If not can check you the nat for traffic and adds the route search key word.

  If you use not all certificates on the SAA you can use the command for related on the SAA rsa keys:

  encryption key tied rsa or try to be specific: related encryption rsa label key<>

  Try to remove the SSH configuration and reapply.

  I would like to know if it works or not. If this isn't the case, then take debug ssh 255 and part.

  Kind regards

  Aditya

  Please evaluate the useful messages.

• 4400 wlc 4.2.176 to 4.2.205 software upgrade

  Hello

  I have 4400 wlc and image backup running as 4.0.206.0 and 4.2.176. Because of certain reservations in the current 4.2.176, we expect to update with 4.2.205.

  WLC >

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} Main boot image... Code 4.2.176.0 (active)
  Backup boot image... Code 4.0.206.0

  I have here are doubts before moving to upgrdation:

  I have it here's the image that has been downloaded from the site of cisco

  Air-WLC4400-K9-4-2-205-0.AES (38 MB file approx.)

  1, but I could see a single file over in the cisco site, which is AIR-WLC4400-K9-4-2-205-0-ER.aes (file 4 MB approx.). I put in the root directory of the TFTP?

  is it necessary to copy the mentioned so 4 MB file?

  2 as show images of starting backup as a 4.0.206.0, what will happen to this file, if I'm upgrading to 4.2.205

  Is what is in the wlc as a backup image?

  3. are there additional things are needed during the upgrade from 4.2.176 to 4.2.205?

  Please suggest me before moving on the same...

  It would be appreciated.

  Hello

  answer your questions:

  1, but I could see a single file over in the cisco site, which is AIR-WLC4400-K9-4-2-205-0-ER.aes (file 4 MB approx.). I put in the root directory of the TFTP?

  is it necessary to copy the mentioned so 4 MB file?

  the 4 MB file (which has ER), is the file of the boot loader.

  It is not necessary to apply it, but it is recommended that you also upgrade to this boot loader after the WLC image upgrade. (as mentioned in the release notes)

  http://www.Cisco.com/en/us/partner/docs/wireless/controller/release/notes/crn42205D3MR4.html

  .Aes ER files are independent of controller software files. You can run any controller software file with any file from ER.aes. However, to install the latest software startup file (4.2.205.0 ER.aes) ensures that changes made to the boot software in all files of the boot software ER.aes past and present are installed.

  -Do not install the 4.2.205.0 software controller file and the startup file software at the same time ER.aes 4.2.205.0. Install a single file and restart the controller; install the other file, and then restart the controller.

  2 as show images of starting backup as a 4.0.206.0, what will happen to this file, if I'm upgrading to 4.2.205

  Is what is in the wlc as a backup image?

  Yes, he'll stay there as backup image.if you want to change it, you must interrupt the boot on console (ESC) process, start the secondary image and do the upgrade again to the secondary image.

  3. are there additional things are needed during the upgrade from 4.2.176 to 4.2.205?

  no extra steps, don't just make sure you use good TFTP as (TFTPD32)

  Here are the release notes for 4.2.205 for your information...

  http://www.Cisco.com/en/us/partner/docs/wireless/controller/release/notes/crn42205D3MR4.html

  Kind regards

  Talal

  =========
  Please note the answers that you find useful and mark as answer - when is it :-) - so that others can easily find

• NAT-control over ASA 5540 v8.3.2?

  Is there an equivalent command in 8.3.2 disable NAT; That is to say. no control NAT?

  I think it was in v7.2 but can't find in in 8.3.2.   I use this stricktly 5540 for a VPN IPSec lan lan 2 head of tunnel and do not NAT at all. If I disable NAT, I won't have to deal with the obnoxious ACL nat_0 which grows and grows and grows. Is this possible in 8.3.2?

  Hello

  The control of nat command has been removed in version 8.3

  The command to control NAT is discouraged. In order to maintain the requirement that all traffic from a security interface than a security interface lower translate, a NAT rule will be inserted at the end of article 2 for each interface ban all remaining traffic. Nat-control command was used for NAT configurations defined with older versions of the Adaptive security appliance. The best practice is to use access rules to control access rather than rely on the absence of a NAT rule to prevent traffic through the Adaptive security device.

  Click on the following link for nat-control migration information:

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa83/upgrading/migrating.html#wp60212

  Federico.

• IPSec tunnel problem work without configuration on asa

  Hello world

  I have a problem with one asa version 8.4.3.

  I have a tunnel if I do not set up the tunnel and if I configure it does not mount to mount with a remote site

  someone that you already see that? With version 8.2, we had no worries, but since he problem of migration.

  Tunnel configuration we get this error:

  IKEv1]: Group = x.x.x.x IP x.x.x.x, QM WSF error = (P2 struct & 0x49ba5a0, mess id 0xcd600011).

  [IKEv1]: Group = x.x.x.x, IP = x.x.x.x, removing counterpart of correlator table failed, no match!

  Thanks for your response

  I have never seen as the result of an ASA simple upgrade, but in general there are a number of things that could cause this problem. Generally, this is one unidentified peer or peer without valid card crypto trying to establish VPN site site that generates the message above.

  Please take a look at this troubleshooting guide.

  If it does not help. Thanks for posting your script