ASA: Show sesiions VPN

What CLI commands display session VPN site-to-site on asa 5520.

Thank you

Colm

ISAKMP crypto to show his<- for="" tunnels="">

and

Crypto ipsec to show his<- for="" tunnel="" traffic="">

Tags: Cisco Security

Similar Questions

How to configure ASA as EZ - vpn client?

How can I configure ASA as Ez - vpn client?

Only ASA 5505 can be configured as a client VPN EZ.

Here's a few example configuration:

http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/ezvpn505.html

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml

Hope that helps.

ASA 5520: Remote VPN Clients cannot ping LAN, Internet

I've set up a few of them in my time, but I am confused with this one. Can I establish connect via VPN tunnel but I can't ping or go on the internet. I searched the forum for similar and found a little issues, but none of the fixes seem to match. I noticed a strange thing is when I run ipconfig/all of the vpn client, the IP address that has been leased over the Pool of the VPN is also the default gateway!

I have attached the config. Help, please.

Thank you!

Exemption of NAT ACL has not yet been applied.

NAT (inside) 0-list of access Inside_nat0_outbound

In addition, you have not split tunnel, not sure you were using internet ASA for the vpn client internet browsing.

You can also enable icmp inspection if you test in scathing:

Policy-map global_policy
class inspection_default

inspect the icmp

Hope that helps.

ASA encrypt interesting VPN traffic

Hello everybody out there using ASA.

I had a few IPSEC VPN tunnels between the company's central site and remote sites.

Two dsl lines were connected to the ASA, one for VPN traffic and the other for the internet.

The default gateway has been configured online internet, some static while insured roads as traffic to the sites of the company was sent through the other line.

A few days ago we changed the configuration of ASA to use only a single dsl connection, then the line serving the internet has been cut, while the other will become the gateway default and static routes have been removed.

The VPN connections instant stopped working and trying to send packets to the remote lan, it seems that ASA will not recognize that the traffic is encrypted. Obviousely we checked cryptomap, acl, ecc, but we find no problem... do you have any suggestions?

Thanks in advance,

Matt

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

XNetwork object network
10.10.0.0 subnet 255.255.255.0

network of the YNetwork object
172.0.1.0 subnet 255.255.255.0

card crypto RB1ITSHDSL001_map2 1 corresponds to the address RB1ITSHDSL001_1_cryptomap
card crypto RB1ITSHDSL001_map2 1 set peer a.b.c.186
RB1ITSHDSL001_map2 1 transform-set ESP-3DES-SHA crypto card game

RB1ITSHDSL001_1_cryptomap list extended access permitted ip XNetwork object YNetwork

-------------------------------------------------------------------------------------------------------------------------------------------------------------------

Hello

Your exit the ASA must be encrypting the traffic between XNetwork and YNetwork.

If the ASA does not encrypt this traffic, it could be because there is a problem with the NAT configuration.

When the ASA receives a packet, it must first check if there are ACLs that allows traffic, passes through the inspection engine and check that the associated NAT. For example, if the package is coordinated, then the private IP encryption will never take place.

Could ensure you that packets from the XNetwork are really reach the ASA, the NAT rule is correct and you may be looking for "debugging cry isa 127" and "scream ips 127" debug to check for errors of incompatibility.

In addition, what is the condition of the tunnel trying to communicate: "sh cry isa his"

Federico.

With the help of ASA for our VPN

I was curious, if through the ASDM, there is a way to show that was recorded in the last week and for how long? I know through the CLI I can use the sh sessiondb-vpn l2l to see who is connected, but trying to get a report of its total use by user, date and time?

Hi Dan,.

The ASA does not all historical data connections so it won't be possible.

You can view the users connected to the part followed by ASDM but you do not have the reporting features.

Kind regards

Nicolas

ASA-to-router VPN, private, public

I have a setup where a customer will send calls to a Complutense University of MADRID, from a private address, through a VPN tunnel Terminal to a 2811. The call to hit a SBC that caters to the public and is located just behind the router on FE0/1. (See photo)

Traffic through the ASA is to be exempted from NAT.

Since it is all public on my end and my waypoints by default for the router of my ISP, I guess I don't have anything other than a default route. (I'm not under routing protocols - just a static outgoing route)

The tunnel does not come to the top. In fact, I never see that no traffic hit my side in all. Does anyone have experience making a private VPN, or know an example of config anywhere?

This is my Bill at the end of the config:

crypto ISAKMP policy 4

BA 3des

md5 hash

preshared authentication

Group 2

lifetime 28800

ISAKMP crypto key XXXXXXXXXX address (public #1) No.-xauth

Crypto ipsec transform-set esp-3des esp-md5-hmac XXXSET

XXXMAP 4 ipsec-isakmp crypto map

defined by peers (public address #1).

Set the security association idle time 3600

game of transformation-XXXSET

PFS group2 Set

match address 170

access-list 170 permit ip host (public address #3) 10.0.0.5

interface FastEthernet0/0

IP (public address #2) 255.255.255.252

load-interval 30

Speed 100

full-duplex

No cdp enable

card crypto XXXMAP

service-policy output AutoQoS-policy-UnTrust

Thank you

Paul

Your configuration looks very good.

Phase 1 comes up when you try to pass traffic through? "cry isa to show her.

Back P1, P2 comes up? "See the crypto ipsec his | I ident | SPI | BA | desc ".

If none is coming, run a debugging:

debugging cry isa

debugging ips cry

See if the tunnel is initiated when traffic is sent. As long as you have a default route pointing outgoing and don't have any other way, you should be fine. Looks like everything will be a connected network.

ASA 5505 ASDM VPN connection problem

Hello

We are running a version of firewall ASA 5505 8.4 (4) 1. The ASDM version is 6.4 (9).

The problem is when the creation of remote access VPN connection, it works fine for about 2-3 days.

After that, the VPN client cannot connect more and gives the error code 789.

In this case, the VPN clients are clients of Windows 7 from different remote networks with the same problem scenario.

Windows 8.1 clients cannot connect at all and show the same error code...

All connections go through the keys defaultragroup and preshare match on both sides.

When the user to connect attemps I receive the following text in the log of the ASDM:

6 April 10, 2015 10:52:39 group = DefaultL2LGroup, IP = 5.240.31.116, P1 retransmit msg sent to the WSF MM

5 April 10, 2015 10:52:39 group = DefaultL2LGroup, IP = 5.240.31.116, in double Phase 1 detected package. Retransmit the last packet.

5 April 10, 2015 10:53:03 IP = 5.240.31.116, encrypted packet received with any HIS correspondent, drop

When I implemented the remote login through ASDM I followed the instructions according to the following link:

http://www.databasemart.com/HOWTO/Cisco_VPN_Remote_Access_Setup_ASA5500...

The steps were a little different, but almost the same, given that these instructions show an old version

I'm interested in trying the steps according to this link but not sure this will help me solve the problem id:

http://www.petenetlive.com/kb/article/0000571.htm

Any help would be appreciated!

Thank you

Hello

If you use local authentication (user name and password on the SAA), so why you would need this threshold?

tunnel-group DefaultRAGroup ppp-attributes
No chap authentication
ms-chap-v2 authentication
!

Remove it and try.

ASA - 2621 S2S vpn

Hello

I have a big problem for the past two days to understand vpn site to site between asa 5520 and router 2621. On my end, there is a firewall and client end it is a router. The negotiation of phase 1 and phase 2 is to succeed and I also saw that the package comes from the remote side. But on the side, I couldn't package runs. I have check the host and he answer icmp and there is no router or a firewall between where it can be relative to the road or any other ACL. What is interesting is that if I trace packet he did not show any failure. I send you the journal also report a few screenshots I did with packet trace and other output (configuration of the firewall and the router) with attachment command.

Thanks for the help.

/ var/log/Firewall # tail-f firewall.log | grep X.X.X.X

7 Jun 21:28:34 172.25.215.1% ASA-7-713236: IP = X.X.X.X, Message RECEIPT of IKE_DECODE (msgid = ef02801e) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

7 Jun 21:28:34 172.25.215.1% ASA-7-715047: Group = X.X.X.X, IP = X.X.X.X, processing hash payload

7 Jun 21:28:34 172.25.215.1% ASA-7-715047: Group = X.X.X.X, IP = X.X.X.X, processing notify payload

7 Jun 21:28:34 172.25.215.1% ASA-7-715075: Group = X.X.X.X, IP = X.X.X.X, received persistent type DPD R-U-LÀ (seq number 0x55622a9e)

7 Jun 21:28:34 172.25.215.1% ASA-7-715036: Group = X.X.X.X, IP = X.X.X.X, sending persistent type DPD R-U-HERE-ACK (seq number 0x55622a9e)

7 Jun 21:28:34 172.25.215.1% ASA-7-715046: Group = X.X.X.X, IP = X.X.X.X, constructing empty hash payload

7 Jun 21:28:34 172.25.215.1% ASA-7-715046: Group = X.X.X.X, IP = X.X.X.X, build payloads of hash qm

7 Jun 21:28:34 172.25.215.1% ASA-7-713236: IP = X.X.X.X, IKE_DECODE SEND Message (msgid = 3c17cf80) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

7 Jun 21:28:47 172.25.215.1% ASA-7-713236: IP = X.X.X.X, Message RECEIPT of IKE_DECODE (msgid = 50c9b74e) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

7 Jun 21:28:47 172.25.215.1% ASA-7-715047: Group = X.X.X.X, IP = X.X.X.X, processing hash payload

7 Jun 21:28:47 172.25.215.1% ASA-7-715047: Group = X.X.X.X, IP = X.X.X.X, processing notify payload

7 Jun 21:28:47 172.25.215.1% ASA-7-715075: Group = X.X.X.X, IP = X.X.X.X, received persistent type DPD R-U-LÀ (seq number 0x55622a9f)

7 Jun 21:28:47 172.25.215.1% ASA-7-715036: Group = X.X.X.X, IP = X.X.X.X, sending persistent type DPD R-U-HERE-ACK (seq number 0x55622a9f)

7 Jun 21:28:47 172.25.215.1% ASA-7-715046: Group = X.X.X.X, IP = X.X.X.X, constructing empty hash payload

7 Jun 21:28:47 172.25.215.1% ASA-7-715046: Group = X.X.X.X, IP = X.X.X.X, build payloads of hash qm

7 Jun 21:28:47 172.25.215.1% ASA-7-713236: IP = X.X.X.X, IKE_DECODE SEND Message (msgid = 1caec174) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

7 Jun 21:29 172.25.215.1% ASA-7-713236: IP = X.X.X.X, Message RECEIPT of IKE_DECODE (msgid = 45868afa) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

7 Jun 21:29 172.25.215.1% ASA-7-715047: Group = X.X.X.X, IP = 85.18.56.130, processing hash payload

7 Jun 21:29 172.25.215.1% ASA-7-715047: Group = X.X.X.X, IP = 85.18.56.130, processing notify payload

7 Jun 21:29 172.25.215.1% ASA-7-715075: Group = X.X.X.X, IP = 85.18.56.130, received persistent type DPD R-U-LÀ (seq number 0x55622aa0)

7 Jun 21:29 172.25.215.1% ASA-7-715036: Group = X.X.X.X, IP = 85.18.56.130, sending persistent type DPD R-U-HERE-ACK (seq number 0x55622aa0)

7 Jun 21:29 172.25.215.1% ASA-7-715046: Group = X.X.X.X, IP = 85.18.56.130, empty building hash payload

7 Jun 21:29 172.25.215.1% ASA-7-715046: Group = X.X.X.X, IP = 85.18.56.130, build payloads of hash qm

7 Jun 21:29 172.25.215.1% ASA-7-713236: IP = X.X.X.X, IKE_DECODE SEND Message (msgid = 46b 88111) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

Looks like the problem is on the SAA. From your other post, I see that you use WAN_2_cryptomap_2 as your ACL interesting traffic, but it does not exist on the ASA. The interesting traffic ACL must be images of mirror of the other.

The router sends traffic to the ASA, but there is no traffic back from the ASA to the router. You can check to see if the devices on the network of 172.25.100.0/24 have a road running through the ASA back to the 10.50.90.0/24 network.

HTH

ASA 5505 IPSEC VPN connected but cannot access the local network

ASA: 8.2.5

ASDM: 6.4.5

LAN: 10.1.0.0/22

Pool VPN: 172.16.10.0/24

Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

Here is my setup, wrong set up anything?

ASA Version 8.2 (5)

!

hostname asatest

domain XXX.com

activate 8Fw1QFqthX2n4uD3 encrypted password

g9NiG6oUPjkYrHNt encrypted passwd

names of

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 10.1.1.253 255.255.252.0

!

interface Vlan2

nameif outside

security-level 0

address IP XXX.XXX.XXX.XXX 255.255.255.240

!

passive FTP mode

clock timezone PST - 8

clock summer-time recurring PDT

DNS server-group DefaultDNS

domain vff.com

vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

pager lines 24

Enable logging

timestamp of the record

logging trap warnings

asdm of logging of information

logging - the id of the device hostname

host of logging inside the 10.1.1.230

Within 1500 MTU

Outside 1500 MTU

IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

no failover

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

AAA-server protocol nt AD

AAA-server host 10.1.1.108 AD (inside)

NT-auth-domain controller 10.1.1.108

Enable http server

http 10.1.0.0 255.255.252.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Telnet timeout 5

SSH 10.1.0.0 255.255.252.0 inside

SSH timeout 20

Console timeout 0

dhcpd outside auto_config

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal group vpntest strategy

Group vpntest policy attributes

value of 10.1.1.108 WINS server

Server DNS 10.1.1.108 value

Protocol-tunnel-VPN IPSec l2tp ipsec

disable the password-storage

disable the IP-comp

Re-xauth disable

disable the PFS

IPSec-udp disable

IPSec-udp-port 10000

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list vpntest_splitTunnelAcl

value by default-domain XXX.com

disable the split-tunnel-all dns

Dungeon-client-config backup servers

the address value vpnpool pools

admin WeiepwREwT66BhE9 encrypted privilege 15 password username

username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

tunnel-group vpntest type remote access

tunnel-group vpntest General attributes

address vpnpool pool

authentication-server-group AD

authentication-server-group (inside) AD

Group Policy - by default-vpntest

band-Kingdom

vpntest group tunnel ipsec-attributes

pre-shared-key BEKey123456

NOCHECK Peer-id-validate

!

!

privilege level 3 mode exec cmd command perfmon

privilege level 3 mode exec cmd ping command

mode privileged exec command cmd level 3

logging of the privilege level 3 mode exec cmd commands

privilege level 3 exec command failover mode cmd

privilege level 3 mode exec command packet cmd - draw

privilege show import at the level 5 exec mode command

privilege level 5 see fashion exec running-config command

order of privilege show level 3 exec mode reload

privilege level 3 exec mode control fashion show

privilege see the level 3 exec firewall command mode

privilege see the level 3 exec mode command ASP.

processor mode privileged exec command to see the level 3

privilege command shell see the level 3 exec mode

privilege show level 3 exec command clock mode

privilege exec mode level 3 dns-hosts command show

privilege see the level 3 exec command access-list mode

logging of orders privilege see the level 3 exec mode

privilege, level 3 see the exec command mode vlan

privilege show level 3 exec command ip mode

privilege, level 3 see fashion exec command ipv6

privilege, level 3 see the exec command failover mode

privilege, level 3 see fashion exec command asdm

exec mode privilege see the level 3 command arp

command routing privilege see the level 3 exec mode

privilege, level 3 see fashion exec command ospf

privilege, level 3 see the exec command in aaa-server mode

AAA mode privileged exec command to see the level 3

privilege, level 3 see fashion exec command eigrp

privilege see the level 3 exec mode command crypto

privilege, level 3 see fashion exec command vpn-sessiondb

privilege level 3 exec mode command ssh show

privilege, level 3 see fashion exec command dhcpd

privilege, level 3 see the vpnclient command exec mode

privilege, level 3 see fashion exec command vpn

privilege level see the 3 blocks from exec mode command

privilege, level 3 see fashion exec command wccp

privilege see the level 3 exec command mode dynamic filters

privilege, level 3 see the exec command in webvpn mode

privilege control module see the level 3 exec mode

privilege, level 3 see fashion exec command uauth

privilege see the level 3 exec command compression mode

level 3 for the show privilege mode configure the command interface

level 3 for the show privilege mode set clock command

level 3 for the show privilege mode configure the access-list command

level 3 for the show privilege mode set up the registration of the order

level 3 for the show privilege mode configure ip command

level 3 for the show privilege mode configure command failover

level 5 mode see the privilege set up command asdm

level 3 for the show privilege mode configure arp command

level 3 for the show privilege mode configure the command routing

level 3 for the show privilege mode configure aaa-order server

level mode 3 privilege see the command configure aaa

level 3 for the show privilege mode configure command crypto

level 3 for the show privilege mode configure ssh command

level 3 for the show privilege mode configure command dhcpd

level 5 mode see the privilege set privilege to command

privilege level clear 3 mode exec command dns host

logging of the privilege clear level 3 exec mode commands

clear level 3 arp command mode privileged exec

AAA-server of privilege clear level 3 exec mode command

privilege clear level 3 exec mode command crypto

privilege clear level 3 exec command mode dynamic filters

level 3 for the privilege cmd mode configure command failover

clear level 3 privilege mode set the logging of command

privilege mode clear level 3 Configure arp command

clear level 3 privilege mode configure command crypto

clear level 3 privilege mode configure aaa-order server

context of prompt hostname

no remote anonymous reporting call

Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

: end

Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

Cisco ASA 5510 L2L VPN on the backup interface

OK, here is what I have and I even if I knew how to do this, but it has not worked for me. I hope someone out there can help you.

I have an ASA 5510 running 8.4 with double configuration of ISPs on 2 different interfaces: outside (primary), backup (backup). I also have a site to site VPN ASA another in another city. The VPN is now configured on the external interface and works very well. What I wanted to do, is to make the VPN running on backup interface only.

So, I changed the card encryption on the remote side to use the backup interface IP and created a tunnel-group for her. Then, I created a map encryption for backup interface and activated ikev1 on it. The default route is configured to use the external interface, so I created a static route that routes traffic destined for the external interface of the remote side to the backup interface default gateway. I can get to establish tunnels, but no traffic passes through them. I have however while I need a NAT device for the tunnel traffic to I created a NAT so but still no transmitted traffic. I tried the packet - trace and he said: the traffic was allowed and show its crypto ipsec command, I see the configuration of the tunnel, but no traffic will pass through it. Can anyone help?

Ben,

you use a code to version 8.4, I recommend starting by removing the config NAT statements at both ends. This version does not have the NAT and control, and if you don't need... I've seen instances with 8.4 (3) where a NAT even though apparently correct was causing not to pass through the traffic.

Site A:

NAT (inside, backup) source static obj-SiteALAN obj-SiteALAN static obj-SiteBLAN obj-SiteBLAN

Site b:

NAT (inside, outside) source static obj - 192.168.5.0 obj - 192.168.5.0 destination static obj - 192.168.3.0 obj - 192.168.3.0

If possible, you should increase your AES encryption, but this is a personal point of view and should not stop the traffic through the links. You should be able to see the counters for the data transmitted / received are these incrementing?

Do you have the ACLs that are from the inside to the outside and internal interface to the Interface of backup (duplicated.

In this model, the control is the routing.

Best regards

Ju

http://helpamunky.WordPress.com/

ASA 5505 ipsec vpn connection fails

Hello

I'm trying to configure a Cisco ASA 5505 for Remote Clients.

I use the ASDM interface and used assistants start and ipsec for my setup, but im hit a stumbling block.

To last make it work 2 days I have tried a number of configuration changes to try to make this work but didn't, so I did a factory reset and passed by the assistants, once again, I have a clean Setup that I hope someone can help me.

Currently I have an IP public static 81.137.x.x and I use a Netgear ADSL router, which transfers (UDP 500) VPN traffic to 192.168.171.35 (port wan on the ASA 5505).

The Cisco ASA has a default address of 192.168.1.1

I use the Cisco Client 5.0.06.0160.

I have configured the client to use authentication group with the same credentials as configuration through the wizard and im using Transparent Tunneling IPSec over UDP.

I have attached 2 documents

running_config.txt - what is shows the current configuration of ASA

Journal - View.txt - display of error messages displayed in the real-time log viewer when I try to connect from the remote client.

I'm not sure if I need to do on the other that additional configurations for my setup simply run the wizards.

Any help would be appreciated.

Thank you

Hello Philippe,

According to the lines in the journal, there is a problem of routing for ip vpn applicant address. ASA couldn't find the definition of route suitable for the return traffic. Add a default route to unknown destinations could solve this problem. As I see you are using modem netgear as a default gateway for your ASA. I write example of command line for this purpose.

Route outside 0.0.0.0 0.0.0.0 NetGear_LAN_IP_Address 1

Ufuk Güler

A possible bug related to the Cisco ASA "show access-list"?

We had a strange problem in our configuration of ASA.

In the "show running-config:

Inside_access_in access-list CM000067 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:http_access

Inside_access_in access-list CM000458 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:https_access

Note to inside_access_in to access test 11111111111111111111111111 EXP:1/16/2014 OWN list: IT_Security BZU:Network_Security

access-list extended inside_access_in permit tcp host 1.1.1.1 host 192.168.20.86 eq 81 Journal

access-list inside_access_in note CM000260 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:netbios - dgm

access-list inside_access_in note CM006598 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:netbios - ns

access-list inside_access_in note CM000220 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:netbios - ssn

access-list inside_access_in note CM000223 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:tcp / 445

inside_access_in list extended access permitted tcp 172.31.254.0 255.255.255.0 any eq www log

inside_access_in allowed extended access list tcp 172.31.254.0 255.255.255.0 any https eq connect

inside_access_in list extended access permit udp 172.31.254.0 255.255.255.0 any eq netbios-dgm log

inside_access_in list extended access permit udp 172.31.254.0 255.255.255.0 connect any eq netbios-ns

inside_access_in list extended access permitted tcp 172.31.254.0 255.255.255.0 any eq netbios-ssn log

inside_access_in list extended access permitted tcp 172.31.254.0 connect any EQ 445 255.255.255.0

Inside_access_in access-list CM000280 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:domain

inside_access_in list extended access permitted tcp object 172.31.254.2 any newspaper domain eq

inside_access_in list extended access permitted udp object 172.31.254.2 any newspaper domain eq

Inside_access_in access-list CM000220 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:catch_all

inside_access_in list extended access permitted ip object 172.31.254.2 any newspaper

Inside_access_in access-list CM0000086 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:SSH_internal

inside_access_in list extended access permitted tcp 172.31.254.0 255.255.255.0 interface inside the eq ssh log

Inside_access_in access-list CM0000011 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:PortRange

inside_access_in list extended access allow object TCPPortRange 172.31.254.0 255.255.255.0 host log 192.168.20.91

Inside_access_in access-list CM0000012 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:FTP

access-list extended inside_access_in permitted tcp object inside_range 1024 45000 192.168.20.91 host range eq ftp log

Inside_access_in access-list CM0000088 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:PortRange

inside_access_in access list extended ip 192.168.20.0 255.255.255.0 allow no matter what paper

Inside_access_in access-list CM0000014 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:DropIP

inside_access_in list extended access permitted ip object windowsusageVM any newspaper

inside_access_in list of allowed ip extended access any object testCSM

inside_access_in access list extended ip 172.31.254.0 255.255.255.0 allow no matter what paper

Inside_access_in access-list CM0000065 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:IP

inside_access_in list extended access permit ip host 172.31.254.2 any log

Inside_access_in access-list CM0000658 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security

inside_access_in list extended access permit tcp host 192.168.20.95 any log eq www

In the "show access-list":

access-list inside_access_in line 1 comment CM000067 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:http_access

access-list inside_access_in line 2 Note CM000458 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:https_access

Line note 3 access-list inside_access_in test 11111111111111111111111111 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security

4 extended access-list inside_access_in line allowed tcp host 1.1.1.1 host 192.168.20.86 eq newsletter interval 300 (hitcnt = 0) 81 0x0a 3bacc1

line access list 5 Note CM000260 EXP:1/16/2014 OWN inside_access_in: IT_Security BZU:Network_Security JST:netbios - dgm

line access list 6 Note CM006598 EXP:1/16/2014 OWN inside_access_in: IT_Security BZU:Network_Security JST:netbios - ns

line access list 7 Note CM000220 EXP:1/16/2014 OWN inside_access_in: IT_Security BZU:Network_Security JST:netbios - ssn

line access list 8 Note CM000223 EXP:1/16/2014 OWN inside_access_in: IT_Security BZU:Network_Security JST:tcp / 445

allowed to Access-list inside_access_in line 9 extended tcp 172.31.254.0 255.255.255.0 any interval information eq www journal 300 (hitcnt = 0) 0 x 06 85254 has

allowed to Access-list inside_access_in 10 line extended tcp 172.31.254.0 255.255.255.0 any https eq log of information interval 300 (hitcnt = 0) 0 x7e7ca5a7

allowed for line access list 11 extended udp 172.31.254.0 inside_access_in 255.255.255.0 any netbios-dgm eq log of information interval 300 (hitcn t = 0) 0x02a111af

allowed to Access-list inside_access_in line 12 extended udp 172.31.254.0 255.255.255.0 any netbios-ns eq log of information interval 300 (hitcnt = 0) 0 x 19244261

allowed for line access list 13 extended tcp 172.31.254.0 inside_access_in 255.255.255.0 any netbios-ssn eq log of information interval 300 (hitcn t = 0) 0x0dbff051

allowed to Access-list inside_access_in line 14 extended tcp 172.31.254.0 255.255.255.0 no matter what eq 445 300 (hitcnt = 0) registration information interval 0 x 7 b798b0e

access-list inside_access_in 15 Note CM000280 EXP:1/16/2014 OWN line: IT_Security BZU:Network_Security JST:domain

allowed to Access-list inside_access_in line 16 extended tcp object 172.31.254.2 any interval information journal field eq 300 (hitcnt = 0) 0x6c416 81 b

allowed to Access-list inside_access_in line 16 extended host tcp 172.31.254.2 any interval information journal field eq 300 (hitcnt = 0) 0x6c416 81 b

allowed to Access-list inside_access_in line 17 extended udp object 172.31.254.2 any interval information journal field eq 300 (hitcnt = 0) 227 0xc53bf

allowed to Access-list inside_access_in line 17 extended udp host 172.31.254.2 all interval information journal field eq 300 (hitcnt = 0) 227 0xc53bf

access-list inside_access_in 18 Note CM000220 EXP:1/16/2014 OWN line: IT_Security BZU:Network_Security JST:catch_all

allowed to Access-list inside_access_in line 19 scope ip object 172.31.254.2 no matter what information recording interval 300 (hitcnt = 0) 0xd063707c

allowed to Access-list inside_access_in line 19 scope ip host 172.31.254.2 any which information recording interval 300 (hitcnt = 0) 0xd063707c

access-list inside_access_in line 20 note CM0000086 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:SSH_internal

permit for line access list extended 21 tcp 172.31.254.0 inside_access_in 255.255.255.0 interface inside the eq ssh information recording interval 300 (hitcnt = 0) 0x4951b794

access-list inside_access_in line 22 NOTE CM0000011 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:PortRange

permit for access list 23 inside_access_in line scope object TCPPortRange 172.31.254.0 255.255.255.0 192.168.20.91 host registration information interval 300 (hitcnt = 0) 0x441e6d68

allowed for line access list 23 extended tcp 172.31.254.0 inside_access_in 255.255.255.0 192.168.20.91 host range ftp smtp log information interval 300 (hitcnt = 0) 0x441e6d68

access-list inside_access_in line 24 Note CM0000012 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:FTP

25 extended access-list inside_access_in line allowed tcp object inside_range Beach 1024 45000 host 192.168.20.91 eq ftp interval 300 0xe848acd5 newsletter

allowed for access list 25 extended range tcp 12.89.235.2 inside_access_in line 12.89.235.5 range 1024 45000 host 192.168.20.91 eq ftp interval 300 (hitcnt = 0) newsletter 0xe848acd5

permit for access list 26 inside_access_in line scope ip 192.168.20.0 255.255.255.0 no interval 300 (hitcnt = 0) newsletter 0xb6c1be37

access-list inside_access_in line 27 Note CM0000014 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:DropIP

allowed to Access-list inside_access_in line 28 scope ip object windowsusageVM no matter what information recording interval 300 (hitcnt = 0) 0 x 22170368

allowed to Access-list inside_access_in line 28 scope ip host 172.31.254.250 any which information recording interval 300 (hitcnt = 0) 0 x 22170368

allowed to Access-list inside_access_in line 29 scope ip testCSM any object (hitcnt = 0) 0xa3fcb334

allowed to Access-list inside_access_in line 29 scope ip any host 255.255.255.255 (hitcnt = 0) 0xa3fcb334

permit for access list 30 inside_access_in line scope ip 172.31.254.0 255.255.255.0 no interval 300 (hitcnt = 0) newsletter 0xe361b6ed

access-list inside_access_in line 31 Note CM0000065 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security JST:IP

allowed to Access-list inside_access_in line 32 scope ip host 172.31.254.2 any which information recording interval 300 (hitcnt = 0) 0xed7670e1

access-list inside_access_in line 33 note CM0000658 EXP:1/16/2014 OWN: IT_Security BZU:Network_Security

allowed to Access-list inside_access_in line 34 extended host tcp 192.168.20.95 any interval information eq www 300 newspapers (hitcnt = 0) 0x8d07d70b

There is a comment in the running configuration: (line 26)

Inside_access_in access-list CM0000088 EXP:1/16/2014 OWN Note: IT_Security BZU:Network_Security JST:PortRange

This comment is missing in 'display the access-list '. In the access list, for all lines after this comment, the line number is more correct. This poses problems when trying to use the line number to insert a new rule.

Everyone knows about this problem before? Is this a known issue? I am happy to provide more information if necessary.

Thanks in advance.

See the version:

Cisco Adaptive Security Appliance Software Version 4,0000 1

Version 7.1 Device Manager (3)

Updated Friday, June 14, 12 and 11:20 by manufacturers

System image file is "disk0: / asa844-1 - k8.bin.

The configuration file to the startup was "startup-config '.

fmciscoasa up to 1 hour 56 minutes

Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor

Internal ATA Compact Flash, 128 MB

BIOS Flash M50FW016 @ 0xfff00000, 2048KB

Hardware encryption device: Cisco ASA-5505 Accelerator Board (revision 0 x 0)

Start firmware: CN1000-MC-BOOT - 2.00

SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.06

Number of Accelerators: 1

Could be linked to the following bug:

CSCtq12090: ACL note line is missing when the object range is set to ACL

The 8.4 fixed (6), so update to a newer version and observe again.

--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

PORT of Configuration.DEFAULT of ASA AnyConnect remote VPN access.

Hello!!! Now, I need to configure the AnyConnect VPN remote access. And I have a question.

The default 443 AnyConnect port, but the port is occupied on SAA. We use this port for another application.

How to change the port to connect? Is this true? Thank you!!!

Hi, please add the following configuration:
1. Enable the WebVPN on the SAA feature:
```
ASA(config)#webvpn
```
2. Enable WebVPN services for the external interface of the ASA:
```
ASA(config-webvpn)#enable outside
```
3. Allow the ASA to listen WebVPN traffic on the custom port number:
```
ASA(config-webvpn)#port <1-65535>
```

ASA 5505. VPN Site-to-Site does not connect!

Hello!
Already more than a week there, as we had a new channel of communication of MGTSa (Ontario terminal Sercomm RV6688BCM, who barely made in the 'bridge' - had to do the provider in order to receive our white Cisco Ip address), and now I train as well more that one week to raise between our IKEv1 IPsec Site-to-Site VPN tunnel closes offices.
Configurable and use the wizard in ASDM and handles in the CLI, the result of a year, the connection does not rise.
Cisco version 9.2 (2), the image of the Cisco asa922 - k8.bin, Security Plus license version, version 7.2 AMPS (2).
What I'll never know...
Debugging and complete configuration enclose below.
Help, which can follow any responses, please! I was completely exhausted!

Config:

Output of the command: "sh run".

: Saved
:
: Serial: XXXXXXXXXXXX
: Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
:
ASA Version 9.2 (2)
!
hostname door-71
activate the encrypted password of F6OJ0GOws7WHxeql
names of
IP local pool vpnpool 10.1.72.100 - 10.1.72.120 mask 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.72.254 255.255.255.0
!
interface Vlan2
nameif outside_mgts
security-level 0
62.112.100.R1 255.255.255.252 IP address
!
passive FTP mode
clock timezone 3 MSK/MSD
clock to DST MSK/MDD recurring last Sun Mar 02:00 last Sun Oct 03:00
DNS lookup field inside
DNS server-group MGTS
Server name 195.34.31.50
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the NET72 object
10.1.72.0 subnet 255.255.255.0
network object obj - 0.0.0.0
host 0.0.0.0
network of the Nafanya object
Home 10.1.72.5
network object obj - 10.1.72.0
10.1.72.0 subnet 255.255.255.0
network of the NET61 object
10.1.61.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.1.72.96_27 object
subnet 10.1.72.96 255.255.255.224
network of the NETT72 object
10.1.72.0 subnet 255.255.255.0
network of the NET30 object
10.1.30.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.1.72.0_24 object
10.1.72.0 subnet 255.255.255.0
object-group service OG INET
the purpose of the echo icmp message service
response to echo icmp service object
service-object icmp traceroute
service-object unreachable icmp
service-purpose tcp - udp destination eq echo
the DM_INLINE_NETWORK_1 object-group network
network-object NET30
network-object, object NET72
DM_INLINE_TCP_1 tcp service object-group
port-object eq www
EQ object of the https port
inside_access_in extended access list permit ip object NET72 object-group DM_INLINE_NETWORK_1
access extensive list ip 10.1.72.0 inside_access_in allow 255.255.255.0 any
inside_access_in extended access list permit ip object Nafanya any idle state
inside_access_in list extended access allowed object-group OG INET an entire
inside_access_in of access allowed any ip an extended list
inside_access_in list extended access deny ip any alerts on any newspaper
outside_mgts_access_in list extended access allowed object-group OG INET an entire
outside_mgts_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_mgts_access_in list extended access deny ip any alerts on any newspaper
access extensive list ip 10.1.72.0 outside_mgts_cryptomap allow 255.255.255.0 object NET61
VPN-ST_splitTunnelAcl permit 10.1.72.0 access list standard 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
outside_mgts MTU 1500
IP check path reverse interface outside_mgts
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside outside_mgts) static source NET72 NET72 NETWORK_OBJ_10.1.72.96_27 NETWORK_OBJ_10.1.72.96_27 non-proxy-arp-search of route static destination
NAT (inside outside_mgts) static source NETWORK_OBJ_10.1.72.0_24 NETWORK_OBJ_10.1.72.0_24 NET61 NET61 non-proxy-arp-search of route static destination
!
network obj_any object
NAT (inside outside_mgts) dynamic obj - 0.0.0.0
network of the NET72 object
NAT (inside outside_mgts) interface dynamic dns
inside_access_in access to the interface inside group
Access-group outside_mgts_access_in in the outside_mgts interface
Route 0.0.0.0 outside_mgts 0.0.0.0 62.112.100.R 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
without activating the user identity
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
Enable http server
http 10.1.72.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
card crypto outside_mgts_map 1 match address outside_mgts_cryptomap
card crypto outside_mgts_map 1 set pfs Group1
peer set card crypto outside_mgts_map 1 91.188.180.42
card crypto outside_mgts_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_mgts_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
card crypto outside_mgts_map interface outside_mgts
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
E-mail [email protected] / * /
name of the object CN = door-71
Serial number
IP address 62.112.100.42
Proxy-loc-transmitter
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint1
registration auto
ASDM_TrustPoint1 key pair
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint0 certificates
certificate eff26954
30820395 3082027d a0030201 020204ef f2695430 0d06092a 864886f7 0d 010105
019
6460ae26 ec5f301d 0603551d 0e041604 14c9a3f2 d70e6789 38fa4b01 465d 1964
60ae26ec 5f300d06 092 has 8648 01050500 03820101 00448753 7baa5c77 86f70d01
62857b 65 d05dc91e 3edfabc6 7b3771af bbedee14 673ec67d 3d0c2de4 b7a7ac05
5f203a8c 98ab52cf 076401e5 1a2c6cb9 3f7afcba 52c617a5 644ece10 d6e1fd7d
28b57d8c aaf49023 2037527e 9fcfa218 9883191f 60b221bf a561f2be d6882091
0222b7a3 3880d6ac 49328d1f 2e085b15 6d1c1141 5f850e5c b6cb3e67 0e373591
94a 82781 44493217 and 38097952 d 003 5552 5c445f1f 92f04039 a23fba20 b9d51b13
f511f311 d1feb2bb 6d056a15 7e63cc1b 1f134677 8124c 024 3af56b97 51af8253
486844bc b1954abe 8acd7108 5e4212df db835d76 98ffdb2b 8c8ab915 193b 8167
0db3dd54 c8346b96 c4f4eff7 1e7cd576 a8b1f86e 3b868a6e 89
quit smoking
string encryption ca ASDM_TrustPoint1 certificates
certificate a39a2b54
3082025f 30820377 a0030201 020204 has 3 9a2b5430 0d06092a 864886f7 0d 010105
0500304 06035504 03130767 36313137 30120603 55040513 6174652d 3110300e b

c084dcd9 d250e194 abcb3eb8 1da93bd0 fb0dba1a b1c35b43 d547a841 5d4ee1a4
14bdb207 7dd790a4 0cd 70471 5f3a896a 07bd56dc ea01b3dd 254cde88 e1490e97
f3e54c05 551adde0 66aa3782 c85880c2 b162ec29 4e49346a df71062d 6d6d8f49
62b9de93 ba07b4f7 a50e77e1 8f54b32b 6627cb27 e982b36f a 362973, 0 88de3272
9bd6d4d2 8ca1e11f 214f20a9 78bdea95 78fdc45c d6d45674 6acb9bcb d0bd930e
638eedfe cd559ab1 e1205c48 3ee9616f e631db55 e82b623c 434ffdc1 11020301
0001 has 363 3061300f 0603551d 130101ff 0101ff30 04053003 0e060355 1d0f0101
ff040403 1f060355 02018630 230418 30168014 0cea70bf 0d0e0c4b eb34a0b1 1 d
8242 has 549 0603 551d0e04 1604140c ea70bf0d 0e0c4beb 34a0b182 301D 5183ccf9
42a 54951 010105 05000382 0101004e 7bfe054a 0d 864886f7 0d06092a 83ccf930
d434a27c 1d3dce15 529bdc5f 70a2dff1 98975de9 2a97333b 96077966 05a8e9ef
bf320cbd ecec3819 ade20a86 9aeb5bde bd129c7b 29341e4b edf91473 f2bf235d
9aaeae21 a629ccc6 3c79200b b9a89b08 bf38afb6 ea56b957 4430f692 a 4745, 411
34d71fad 588e4e18 2b2d97af b2aae6b9 b6a22350 d031615b 49ea9b9f 2fdd82e6
ebd4dccd df93c17e deceb796 f268abf1 881409b 5 89183841 f484f0e7 bd5f7b69
ebf7481c faf69d3e 9d24df6e 9c2b0791 785019f7 a0d20e95 2ef35799 66ffc819
4a77cdf2 c6fb4380 fe94c13c d4261655 7bf3d6ba 6289dc8b f9aad4e1 bd918fb7
32916fe1 477666ab c2a3d591 a84dd435 51711f6e 93e2bd84 89884c
quit smoking
crypto isakmp identity address
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate outside_mgts port 443 customer service
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Crypto ikev1 allow inside
Crypto ikev1 enable outside_mgts
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
without ssh stricthostkeycheck
SSH 10.1.72.0 255.255.255.0 inside
SSH timeout 60
SSH group dh-Group1-sha1 key exchange
Console timeout 0
vpnclient Server 91.188.180.X
vpnclient mode network-extension-mode
vpnclient nem-st-autoconnect
VPN - L2L vpnclient vpngroup password *.
vpnclient username aradetskayaL password *.
dhcpd auto_config outside_mgts
!
dhcpd update dns replace all two interface inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust ASDM_TrustPoint0 inside point
SSL-trust ASDM_TrustPoint0 outside_mgts point
WebVPN
Select outside_mgts
internal GroupPolicy_91.188.180.X group strategy
attributes of Group Policy GroupPolicy_91.188.180.X
Ikev1 VPN-tunnel-Protocol
internal group VPN - ST strategy
attributes of group VPN - ST policy
value of 195.34.31.50 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value VPN-ST_splitTunnelAcl
by default no
aradetskayaL encrypted HR3qeva85hzXT6KK privilege 15 password username
tunnel-group 91.188.180.X type ipsec-l2l
attributes global-tunnel-group 91.188.180.X
Group - default policy - GroupPolicy_91.188.180.42
IPSec-attributes tunnel-group 91.188.180.X
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
remote access to tunnel-group VPN - ST type
VPN-general ST-attributes tunnel-group
address vpnpool pool
Group Policy - by default-VPN-ST
tunnel-group ipsec VPN ST-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:212e4f5035793d1c219fed57751983d8
: end

door-71 # sh crypto ikev1 his

There are no SAs IKEv1

door-71 # sh crypto ikev2 his

There are no SAs IKEv2

door-71 # sh crypto ipsec his

There is no ipsec security associations

door-71 # sh crypto isakmp

There are no SAs IKEv1

There are no SAs IKEv2

Global statistics IKEv1
The active Tunnels: 0
Previous Tunnels: 0
In bytes: 0
In the packages: 0
In packs of fall: 0
In Notifys: 0
In the constituencies of P2: 0
In P2 invalid Exchange: 0
In P2 Exchange rejects: 0
Requests for removal in his P2: 0
Bytes: 0
Package: 0
Fall packages: 0
NOTIFYs out: 0

Exchanges of P2: 0
The Invalides Exchange P2: 0
Exchange of P2 rejects: 0
Requests to remove on P2 Sa: 0
Tunnels of the initiator: 0
Initiator fails: 0
Answering machine fails: 0
Ability system breaks down: 0
AUTH failed: 0
Decrypt failed: 0
Valid hash fails: 0
No failure his: 0

IKEV1 statistics for Admission appeals
In negotiating SAs Max: 25
In negotiating SAs: 0
In negotiating SAs Highwater: 0
In negotiating SAs rejected: 0

Global statistics IKEv2
The active Tunnels: 0
Previous Tunnels: 0
In bytes: 0
In the packages: 0
In packs of fall: 0
In Fragments of fall: 0
In Notifys: 0
In Exchange for the P2: 0
In P2 invalid Exchange: 0
In P2 Exchange rejects: 0
In IPSEC delete: 0
In delete IKE: 0
Bytes: 0
Package: 0
Fall packages: 0
Fragments of fall: 0
NOTIFYs out: 0
Exchange of P2: 0
The Invalides Exchange P2: 0
Exchange of P2 rejects: 0
On IPSEC delete: 0
The IKE Delete: 0
Locally launched sAs: 0
Locally launched sAs failed: 0
SAs remotely initiated: 0
SAs remotely initiated failed: 0
System capacity: 0
Authentication failures: 0
Decrypt failures: 0
Hash failures: 0
Invalid SPI: 0
In the Configs: 0
Configs: 0
In the Configs rejects: 0
Configs rejects: 0
Previous Tunnels: 0
Previous Tunnels wraps: 0
In the DPD Messages: 0
The DPD Messages: 0
The NAT KeepAlive: 0
IKE recomposition launched locally: 0
IKE returned to the remote initiated key: 0
Generate a new key CHILD initiated locally: 0
CHILD given to the remote initiated key: 0

IKEV2 statistics for Admission appeals
Max active SAs: no limit
Max in negotiating SAs: 50
Challenge cookie line: never
Active sAs: 0
In negotiating SAs: 0
Incoming requests: 0
Accepted incoming requests: 0
A rejected incoming requests: 0
Out of requests: 0
Out of the applications accepted: 0
The outgoing rejected requests: 0
A rejected queries: 0
Rejected at the SA: 0 Max limit
Rejected low resources: 0
Rejected the current reboot: 0
Challenges of cookie: 0
Cookies transmitted challenges: 0
Challenges of cookie failed: 0

IKEv1 global IPSec over TCP statistics
--------------------------------
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Incoming packets: 0
Inbound packets ignored: 0
Outgoing packets: 0
Outbound packets ignored: 0
The RST packets: 0
Heartbeat Recevied ACK packets: 0
Bad headers: 0
Bad trailers: 0
Chess timer: 0
Checksum errors: 0
Internal error: 0

door-71 # sh statistical protocol all cryptographic
[Statistics IKEv1]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[Statistics IKEv2]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[IPsec statistics]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0

ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[SSL statistics]
Encrypt packets of queries: 19331
Encapsulate packets of queries: 19331
Decrypt packets of queries: 437
Package requests decapsulating: 437
HMAC calculation queries: 19768
ITS creation queries: 178
SA asked to generate a new key: 0
Requests to remove SA: 176
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[Statistical SSH are not taken in charge]
[Statistics SRTP]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[Statistics]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 6238
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of queries random generation: 76
Failure of queries: 9
door-71 # sh crypto ca trustpoints

Trustpoint ASDM_TrustPoint0:
Configured for the production of a self-signed certificate.

Trustpoint ASDM_TrustPoint1:
Configured for the production of a self-signed certificate.

If you need something more, then spread!
Please explain why it is that I don't want to work?

Hello

When the IPSEC tunnel does not come to the top, the first thing comes to my mind is to run a tracer of package from the CLI and the phases in it. Please run this command from your firewall side and share the output. I've just compiled this command with the random ip address and ports of your given range.

Packet-trace entry inside tcp 10.1.72.2 1233 10.1.61.2 443 detailed

Best regards

Amandine

Cisco ASA AnyConnect SSL VPN - certificates + token?

Hello

I'm looking for an answer is it possible such configuration:

The Cisco AnyConnect SSL VPN service with two-factor - first method is the Microsoft CA certificate local and second method - a token solution Symantec VIP password?

I don't know if two-factor authentication is user/password from Active Directory + OTP by Symantec VIP there is no problem, because you can send the user + pass with Radius, but with certificates I do not really understand who will check the validity of the certificate, which certificate, we will send you to the RADIUS for the validation server and how the configuration of the point of view of ASA will look like.

Thank you very much for the help!

Hi Alex,

I don't see a problem with having certificate + token to connect to the VPN. Certificate authentication must be performed on the SAA, see an example below:

https://supportforums.Cisco.com/blog/152941/AnyConnect-certificate-based-authentication

Authentication token can be specified as primary/secondary (authentication SDI) on the SAA, an example below:

http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/anyconnect31/Administration/Guide/anyconnectadmin31/ac11authenticate.html#pgfId-1060345

It may be useful

-Randy-

ASA: Show sesiions VPN

Similar Questions

Maybe you are looking for