ASA VPN connection cannot see all subnets
I'm new to the ASA and I have a problem with our remote users. When people access vpn, they don't see a couple subnets on the network. I looked at the ASA and he can see and communicate with subnets, but when you vpn in them is not reachable. All these connections are connections from admin to admin privlages. Anyone know why the ASA can see subnets, but the admin vpn users cannot?
You compare your ACL split tunnel and your table routing, but only for networks that are relevant to you and you must have access to and are not outside the old configuration. You should also ensure that these networks can route traffic from the pool of vpn.
Tags: Cisco Security
Similar Questions
-
Can connect via the VPN, but cannot see the files
I can connect via VPN to my company network, but the files do not arise under Vista. I have no problem to see them on my old Windows PC, so this is a specific problem of Vista. On my old system, just click on computer and it shows me my company on the network's records. No Vista - cannot find anywhere, even if I am connected via VPN. Where are they?
Hello
Since it is the network of the company, there is no way to know hwo security is configured, unless you are a computer scientist in society.
Not "mess up" your computer, first talking to the person in charge of VPN connections.
Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET
-
VPN connects, cannot get to anything on the LAN
OK, what don't get me? My VPN connects OK with the Version of the Client 5.0.07.0290 VPN but I can't access anything on the 10.0.0.0/24 network.
Any thoughts? I should be able to ping the server 10.0.0.90 if it worked properly in my laptop while I'm on the VPN. Following configuration:
ASA Version 7.2 (4)
!
hostname XXXX
domain energy.com
activate jp28ZvYIS1PQVK6M encrypted password
UmzM9i7pSqpXEdTR encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 10.0.0.9 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address 74.x.x.150 255.255.255.248
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone IS - 5
DNS server-group DefaultDNS
domain energy.com
access-list 101 extended allow ip 10.0.0.0 255.255.255.0 192.168.150.0 255.255.255.0
access-list sheep extended ip 10.0.0.0 allow 255.255.255.0 192.168.150.0 255.255.255.0
outside_in list extended access permit tcp any host 74.x.x.146 eq 35330
outside_in list extended access permit tcp any host 74.x.x.147 eq 10000
outside_in list extended access permit icmp any one
outside_in list extended access permit tcp any host 74.x.x.148 eq 990
outside_in list extended access permit udp any host 74.x.x.148 eq 900
outside_in list extended access permit tcp any host 74.x.x.148 4000-4099
access-list extended outside_in permit udp any host 4000-4099 74.x.x.148
outside_in list extended access permit udp any host 74.x.x.148 eq 990
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 100000
debug logging in buffered memory
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP local pool dhcppptp-192.168.150.1 - 192.168.150.20
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 524.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 10.0.0.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
public static 74.x.x.146 (Interior, exterior) 10.0.0.90 netmask 255.255.255.255
static (inside, outside) 74.x.x.147 10.0.0.91 netmask 255.255.255.255
public static 74.x.x.148 (Interior, exterior) 10.0.0.3 netmask 255.255.255.255
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 74.x.x.145 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
Enable http server
http 10.0.0.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto dynamic-map cisco 1 transform-set RIGHT
dynamic dyn-map 20-isakmp ipsec crypto map Cisco
dyn-map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 1
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet 10.0.0.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
TFTP server inside 10.0.0.109 cpix.cfg
internal BEVPN group policy
BEVPN group policy attributes
Server DNS 10.0.0.4 value 10.0.0.1
VPN-idle-timeout 30
Split-tunnel-policy tunnelall
Split-tunnel-network-list value 101
maindomain.com value by default-field
disable authentication of the user
IPSec-attributes tunnel-group DefaultL2LGroup
pre-shared-key *.
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared-key *.
ISAKMP ikev1-user authentication no
tunnel-group BEVPN type ipsec-ra
attributes global-tunnel-group BEVPN
address-pool dhcppptp pool
Group Policy - by default-BEVPN
IPSec-attributes tunnel-group BEVPN
pre-shared-key *.
ISAKMP ikev1-user authentication no
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the preset_dns_map dns
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:b379566df0e7f5213ad2396676763859
: end
Hello
I don't see the NAT0 configuration more in this configuration
NAT (inside) 0 access-list sheep
You can also change the ACL of Split Tunnel
standard access list permits 10.0.0.0 SPLIT-TUNNEL 255.255.255.0
BEVPN group policy attributes
no value of split-tunnel-network-list 101
Split-tunnel-network-list value of SPLIT TUNNEL
You can also use the "show run" command that will generate a little less production
-Jouni
-
Toshiba Kira - Win 8.1 cannot see all files on the 64 GB flash drive
Hi all
Newbie on this forum. I just bought the i5 8 GB of RAM Windows 8.1 Kira Ultrabook, a great little machine.
I have a SanDisk 64 GB flash drive that has about 20 GB on it in a dozen files. These folders and the content can be seen by my Windows 7 PC, even my mobile phone and Tablet Tower.
However, the Kira cannot see both files, even if in the properties of the drive, he sees the space correctly. Turned on all folders and no difference.
My wife has a 32 GB flash - no problem.I reformatted the flash disk, run a virus on the disk and the Kira. The Kira can someone verify the maximum size flash can see it please? I can't find it in any documentation.
Any help or suggestions appreciated - I ran support Toshiba without a response, so maybe someone here can help you.
Mark
Brisbane AustraliaThe appearance of the folder is not in your laptop model or your system!
I recommend you to check some common view windows Explorer settings:
(1) to see the hidden files and folders reported as
Click the view tab, and then click Show hidden files and folders.(2) to display all the system files that are usually hidden from view.
Click on the view tab, and then clear the Hide protected operating system files check box.Here you will find all the information about the folder views and behavior
http://Windows.Microsoft.com/en-us/Windows-Vista/change-folder-views-and-behavior -
ex485 remote connection cannot see music
I went through the entire setup for remote access to my ex485 MediaSmart Server.
Everything works well except for one thing. I can see all my photos so that indicates
that the bones of connection works fine. In my music, I can see all the folders, Albums, artists,
etc., except when I browse the songs there is no track (0) in one of the albums.
They are there on the server itself and I can play them fine on my local network.
It doesn't matter if I connect remotely via a computer or my iphone (via HP MediaSmart iStream).
Any ideas?
Larry
OK, I played a bit with this enough to make it work. Turns on when you configure Twonkymedia you have to tell it to serve all Types of files in the music folder, not only the music files. iTunes rips of CD to m4a and Twonky file types does not seem to know that they are music files. Change all types actually serve them as well.
Larry
-
Cannot see all the specifications of customizaton... why?
We have two vCenters in bound mode. If I create a virtual computer on a site and you choose to use a specification of previous customization that I see about 1/2 of the plug. If I do the same thing to the other site I get about the other 1/2 (give or take). I built a new virtual machine in my second site, thinking that if I taped the first site would see it. Well, I don't see it at all in my technical customization Manager.
Any ideas on that?
HI, oops I meant to edit and say that I figured this out. Even if two vCenters are in bound mode, it seems that the models cannot see card customization of their respective vCenters. I created a similar technique on my other vCenter and was able to see it!
-
Satellite A350-13 b cannot see all Wi - Fi networks
Hello
I have this weird problem - out my wifi doesn't work.
Internet works on cable, I can't see all wifi networks.
I tried to turn wifi on and off the power by using the lock, as well as with fn + F8.I was looking for a driver (just out of ideas, he worked for like 2 years...) but found no apropriate, find a driver for toshiba is a pain...
My os is windows 7 32 bit. I would be very gratefull for any help :).
Hello
The FN + F8 does not work if there is a WLan driver problem.
So recommend doing this:First remove the battery and AC adapter.
Press the power button / stop along 30 sec
Then reconnect the two parts.
Now switch on and press F2 to enter the BIOS
Value of the default BIOS by pressing F9 and save changes by pressing F10
Start the Windows operating system BIOS access
Now download the compatible WLan driver (I guess as its WiFi Intel 5100AGN)
http://APS2.toshiba-tro.de/WLAN/After the installation of the Wlan driver, install the package of added value and utility of Flash memory card Support.
Restart the laptop and try to activate Wlan again. -
Hi my email acc page is huge writing is so great, I don't see all of my messages or email how do I get it back to normal
Forum hotmail here
-
AnyConnect VPN users cannot access remote subnets?
I googled this until blue in the face without result. I don't understand why Cisco this so difficult? When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices. What should I do to allow my anyconnect vpn clients access to my remote sites?
Cisco 5510 8.4
Hello
What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.
In addition to routing, you must have configured for each remote site and the VPN pool NAT0
Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this
object-group network to REMOTE SITES
object-network 10.10.10.0 255.255.255.0
object-network 10.10.20.0 255.255.255.0
object-network 10.10.30.0 255.255.255.0
object-network 10.10.40.0 255.255.255.0
network of the VPN-POOL object
10.10.224.0 subnet 255.255.255.0
NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL
The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.
Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.
My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)
Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?
-Jouni
-
VPN users cannot access all resources
User is able to connect, get's assigned an IP, we can see them connected
via ASDM, they can't access anything in our network.
Hello
Check the following:
When you try to send the traffic check the output of "sh cry ips her" to make sure packages encrypted/decrypted by slices.
If it isn't...
May be that NAT - T is not configured.
Check the configuration of:
ISAKMP crypto nat - t
SH run all sysopt--> should show sysopt connection permit VPN
Test:
Add the command
management-access inside
And try to PING IP address of the VPN client ASA inside.
We will consider here...
Federico.
-
Site to Site between ASA VPN connection and router 2800
I'm trying to get a L2L VPN working between a ASA code 8.4 and a 2800 on 12.4.
I first saw the following errors in the debug logs on the side of the ASA:
Error message % PIX | ASA-6-713219: KEY-GAIN message queues to deal with when
ITS P1 is complete.I see the following on the end of 2800:
ISAKMP: (0): treatment charge useful vendor id
ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 157
ISAKMP: (0): provider ID is NAT - T v3
ISAKMP: (0): treatment charge useful vendor id
ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
ISAKMP (0): provider ID is NAT - T RFC 3947
ISAKMP: (0): treatment charge useful vendor id
ISAKMP: (0): treatment of frag vendor id IKE payload
ISAKMP: (0): IKE Fragmentation support not enabled
ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1ISAKMP: (0): built NAT - T of the seller-rfc3947 ID
ISAKMP: (0): send package to x.x.x.x my_port 500 peer_po0 (R) MM_SA_SETUP
ISAKMP: (0): sending a packet IPv4 IKE.
ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM2ISAKMP (0): packet received from x.x.x.x dport 500 sports global (R)
MM_SA_SETUP
ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
ISAKMP: (0): former State = new State IKE_R_MM2 = IKE_R_MM3ISAKMP: (0): processing KE payload. Message ID = 0
ISAKMP: (0): processing NONCE payload. Message ID = 0
ISAKMP: (0): found peer pre-shared key x.x.x.x corresponding
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): provider ID is the unit
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): provider ID seems the unit/DPD but major incompatibility of 54
ISAKMP: (2345): provider ID is XAUTH
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): addressing another box of IOS!
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): vendor ID seems the unit/DPD but hash mismatch
ISAKMP: receives the payload type 20
ISAKMP (2345): sound not hash no match - this node outside NAT
ISAKMP: receives the payload type 20
ISAKMP (2345): no NAT found for oneself or peer
ISAKMP: (2345): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP: (2345): former State = new State IKE_R_MM3 = IKE_R_MM3ISAKMP: (2345): sending package x.x.x.x my_port Exchange 500 500 (R)
MM_KEY_EXCH
----------
This is part of the configuration of the ASA:
network of the ABCD object
10.20.30.0 subnet 255.255.255.0
network of the ABCD-Net object
172.16.10.0 subnet 255.255.255.0
cry-map-77-ip object-group XXXX object abc-site_Network allowed extended access list
access list abc-site extended permitted ip object-group XXXX object abc-site_Network
ip access list of abc-site allowed extended object abc-site_Network object-group XXXX-60
NAT (any, any) static source 20 XXXX XXXX-20 destination static abc-site_Network abc-site_Network
NAT (any, any) static source 20 XXXX XXXX-20 destination static abc-site_Network abc-site_Network
XXXX-20
object-group network XXXX-20
ABCD-Net network object
object-abcd-Int-Net Group
XXXX_127
object-group network XXXX-20
ABCD-Net network object
object-abcd-Int-Net Group
ip access list of abc-site allowed extended object abc-site_Network object-group XXXX-60
Crypto card off-map-44 11 match address cry-map-77
card crypto out-map-44 11 counterpart set 62.73.52.xxx
card crypto out-map-44 11 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5cry-map-77-ip object-group XXXX object abc-site_Network allowed extended access list
Crypto card off-map-44 11 match address cry-map-77
card crypto out-map-44 11 counterpart set 62.73.52.xxx
card crypto out-map-44 11 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5card crypto out-map-44 11 set transform-set ESP-3DES-SHA ikev1
object-group network XXXX
ABCD-Net network object
object-abcd-Int-Net Group------------------------
Here is a part of the 2800:
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
ISAKMP crypto key r2374923 address 72.15.21.xxx
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
card crypto cry-map-1 1 ipsec-isakmp
the value of 72.15.21.xxx peer
game of transformation-ESP-3DES-SHA
match address VPN
!
type of class-card inspect match class-map-vpn
game group-access 100
type of class-card inspect cm-inspect-1 correspondence
group-access name inside-out game
type of class-card inspect correspondence cm-inspect-2
match the name of group-access outside
!
!
type of policy-card inspect policy-map-inspect
class type inspect cm-inspect-1
inspect
class class by default
drop
type of policy-card inspect policy-map-inspect-2
class type inspect class-map-vpn
inspect
class type inspect cm-inspect-2
class class by default
drop
!!
interface FastEthernet0
IP address 74.25.89.xxx 255.255.255.252
NAT outside IP
IP virtual-reassembly
security of the outside Member area
automatic duplex
automatic speed
crypto cry-card-1 card
!
interface FastEthernet1
no ip address
Shutdown
automatic duplex
automatic speed
!
IP nat inside source overload map route route-map-1 interface FastEthernet0
!
IP access-list extended inside-out
IP 172.16.10.0 allow 0.0.0.255 any
IP nat - acl extended access list
deny ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
deny ip 10.200.0.0 0.0.255.255 172.16.10.0 0.0.0.255
deny ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
deny ip 0.0.255.255 28.20.14.xxx.0.0 172.16.10.0 0.0.0.255
refuse the 10.10.10.0 ip 0.0.0.255 172.16.10.0 0.0.0.255
refuse the 172.16.10.0 ip 0.0.0.255 192.168.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 10.200.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 192.168.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 10.10.10.0 0.0.0.255
allow an ip
outside extended IP access list
allow an ip
list of IP - VPN access scope
IP 172.16.10.0 allow 0.0.0.255 192.168.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 10.200.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 192.168.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 10.10.10.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
IP 10.200.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
28.20.14.xxx.0.0 0.0.255.255 ip permit 172.16.10.0 0.0.0.255
ip licensing 10.10.10.0 0.0.0.255 172.16.10.0 0.0.0.255access-list 23 allow 192.168.0.0 0.0.255.255
access-list 23 allow 10.200.0.0 0.0.255.255
access-list 23 allow 172.16.10.0 0.0.0.255
access-list 123 note category class-map-LCA-4 = 0
access-list 123 allow ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 10.200.0.0 0.0.255.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 0.0.255.255 28.20.14.xxx.0.0 172.16.10.0 0.0.0.255
access-list 123 allow ip 10.10.10.0 0.0.0.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 10.200.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 10.10.10.0 0.0.0.255
!
!
!!
route-map-1 allowed route map 1
match the IP nat - acl
!Hello
I quickly browsed your config and I could notice is
your game of transformation (iskamp) on SAA and router are not the same, try to configure the same on both sides.
in the statement of the ASA NAT you gave (any, any) try to give the name of the interface instead of a whole.
-
laptop will not connect or see all networks
Hi I just reloaded my os (windows vista) and finish all updates from microsoft and for some reason any, he sees not all networks at all so I click on diagnose and it says wireless networking hardware installation and check the correct drivers are loaded. It worked before I reloaded the os and I downloaded the drivers from dell (I have dell ispiron 1525 family vista Basic) and still does not work someone help
Download the drivers from the link above from Dell.
The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems
Troubleshoot network adapter problems to Microsoft link above.
Try without commitment TCP/IPv6:
If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)
http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/
See you soon.
Mick Murphy - Microsoft partner
-
iPhone - ASA VPN connects and gets disassembly
Hello world...
I have a VPN working properly on a 8.0 (5) ASA, but when I try to connect from an iPhone (IOS 5.1.1) it connects and immediately Gets a teardown.
Any thoughts?
Thank you!
can you pls share your config ASA and advise what group policy, you use for iphone users?
-
Master Pro XP and XP Home Slave - cannot see all files on the slave
Hi all
I had an old Dell Dimension, who dies, who was running XP Home. so, I removed the old hard drive and installed as a "slave" drive in a second Dimension of Dell running XP Pro. The system XP Pro recognized and installed the old XP Home hard drive as a slave with no problems. I can see a variety of directories and files on the drive slave (even the Windows directories and program); However, I don't see the 'Documents and Settings' from the old system. And of course, that's where all the data I want to access to lies. When I look at the two drives under "my computer" (XP Pro System), the (s) 'total size' and 'free space' seems correct; So, it seems that the data is there. I can't do it.You can provide any help will be greatly appreciated, thank you.Reed(* E-mail address is removed from the privacy *)No idea if it will work, but make sure that hidden files are able to see, you can also try to go to start and run and type something like "d:\documents and settings" replacing the d: with your other drive, but keep the quotation marks :D
-
Cannot see all files on external drives (external HARD drive / flashdrives)
I do not see any folder on my external hard drive, I know that these files exist because it still shows how the same amount of space remaining left on this drive. Is the same for all flashdrives I plug it into my laptop
Edit * directories to the folders still exist, I can access when I type in my address bar, but I can't see the icon to click on it.
Hello
Windows 7 sometimes has trouble seeing external drives. Found one potential than me and other solution is to download and install the freeware Aomei Partition Assistant application, download it here: http://download.cnet.com/AOMEI-Partition-Assistant-Standard-Edition/3000-18512_4-75118871.html?tag=mncol;1 (only use the Direct download link).
Once installed, go to the readers in question and one both select and select Properties. It is her, no formatting or partitioning required. Just select the drive is often enough to get Windows 7 to recognize.
Post your results here and let me know how you fare.
Kind regards
BearPup
Maybe you are looking for
-
Is PA3512U-1M1G 1 GB memory PC2 DDR2 667 MHz compatible with Satellite A100-847
Is PA3512U - 1M1G 1 GB memory PC2 DDR2 (667 MHz), RoHS compliance version compatible with TOSHIBA SATELLITE A100-847?
-
Hello, I made a VI which consists of two tabbed pages. Each page has three buttons-> you measurement procedures At the start of the VI, always the initialization is performed. When to switch between pages, always initialization is done. Everything wo
-
When I opened my sysem information, he says that he cannot get the information. Are there any which force to retrieve this information again. Nbss ' t there is information in a category or subcategory. Thank you.
-
Hello I upgraded to BB10 of BB9900 and I can't find a way to hide my email. I use yahoo for sending small businesses & reading emails on my BB10 I mask with my office email address. Previously, using my BB9900 and other models blackberry before it, t
-
Blend modes Photoshop CC 2015.5 does not
I have a pixel layer where none of the blending modes are applied. I'm on Mac, RGB, 16-bit. I am an experienced user of Photoshop, but have never experienced this problem. I can apply adjustment layers, but some blend modes not.