ASA5505 - Maximum VPN Clients

Hey all, any idea what the maximum number of VPN clients can connect to the ASA5505? It runs to the base image. Thank you, robert.

The devices allowed for this platform:

The maximum physical Interfaces: 8

VLAN: 3, restricted DMZ

Internal hosts: unlimited

Failover: disabled

VPN - A: enabled

VPN-3DES-AES: enabled

Peer VPN: 10

WebVPN peers: 2

Double ISP: disabled

Junction ports VLAN: 0

This platform includes a basic license.

Yes, apparently your interpretation is correct. If you have a race box you lab this place and see what happens after the grid of th 11' client attempted to connect. Most likely the client wil see an error message.

Please rate if useful.

Concerning

Farrukh

Tags: Cisco Security

Similar Questions

  • Routing between the easy VPN clients

    I have easy installation of multiple ASA5505 as VPN clients connecting to a single ASA5510 and can route packets between client subnets easy 5505. Anyone has the clues, how?

    Thank you!

    You must add the below to the 5510: -.

    permit same-security-traffic intra-interface

    HTH >

  • Cisco VPN Client anything cannot access through VPN on an ASA5505 8.4

    Hello

    Completely new to Cisco ASA and the need to get this working ASAP.

    8.4 (1) ASA 5505 is the secondary FW and I need to authorize all out and block everything coming, but for the VPN clients.  Since a jerk of Cisco, I used the ASDM and it's sorcerers to make this work, which may explain my situation.

    192.168.101.0/24 is the local network

    192.168.101.5 is the IP of ASA

    192.168.101.2 is the primary FW (and the default gateway for servers, I have to access through the VPN)

    10.10.101.0/24 is the VPN IP range (this can be what you want, I'm not married to it somehow)

    My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x or service server (tried RDP, telnet, ping, etc.)

    Configuration file is attached.

    Help pretty please!

    Thank you.

    Did you add a route for the VPN Pool on the main firewall to the ASA?

    Best regards

    Peer

    Sent by Cisco Support technique iPad App

  • Routing issue of Cisco VPN Client ASA

    Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

    Here the IP Configuration and the routing of the Barracuda firewall table:

    I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

    The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

    Here is the config Cisco ASA:

     : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

    Can someone please help me solve this problem?

    When I tried to solve this I didn't choose which interface the Packet Tracer?

    The interface inside or DMZ interface?  Inside, he says it will not work with the dmz but the error did not help me

    Anyone here knows why it does not work?

    Hello

    Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

    entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

    Route by tunnel watch also with 255 administrative distance.  I've never used that in my scenarios... lets see...

    Concerning

    Knockaert

  • LAN ASA 5505 VPN client access issue

    Hello

    I'm no expert in ASA and routing so I ask support the following case.

    There is a (running on Windows 7) Cisco VPN client and an ASA5505.

    The objectives are client can use the gateway remote on SAA for Skype and able to access devices in SAA within the interface.

    The Skype works well, but I can't access devices in the interface inside through a VPN connection.

    Can you please check my following config and give me any advice to fix NAT or VPN settings?

    ASA Version 7.2 (4)

    !

    ciscoasa hostname

    domain default.domain.invalid

    activate wDnglsHo3Tm87.tM encrypted password

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address dhcp setroute

    !

    interface Vlan3

    prior to interface Vlan1

    nameif dmz

    security-level 50

    no ip address

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    DNS server-group DefaultDNS

    domain default.domain.invalid

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    inside_access_in list extended access permitted tcp 192.168.1.0 255.255.255.0 any

    inside_access_in list extended access permitted udp 192.168.1.0 255.255.255.0 any

    outside_access_in list of allowed ip extended access entire 192.168.1.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    MTU 1500 dmz

    local pool VPNPOOL 10.0.0.200 - 10.0.0.220 255.255.255.0 IP mask

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 524.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    Global 1 interface (outside)

    NAT (inside) 1 10.0.0.0 255.255.255.0

    NAT (inside) 1 192.168.1.0 255.255.255.0

    NAT (outside) 1 10.0.0.0 255.255.255.0

    inside_access_in access to the interface inside group

    Access-group outside_access_in in interface outside

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    the ssh LOCAL console AAA authentication

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto-map dynamic outside_dyn_map pfs set 20 Group1

    Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.0 inside

    SSH timeout 5

    SSH version 2

    Console timeout 0

    dhcpd outside auto_config

    !

    dhcpd address 192.168.1.2 - 192.168.1.33 inside

    dhcpd dns xx.xx.xx.xx interface inside

    dhcpd allow inside

    !

    attributes of Group Policy DfltGrpPolicy

    No banner

    WINS server no

    value of server DNS 84.2.44.1

    DHCP-network-scope no

    VPN-access-hour no

    VPN - connections 3

    VPN-idle-timeout 30

    VPN-session-timeout no

    VPN-filter no

    Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

    disable the password-storage

    disable the IP-comp

    Re-xauth disable

    Group-lock no

    disable the PFS

    IPSec-udp disable

    IPSec-udp-port 10000

    Split-tunnel-policy tunnelall

    Split-tunnel-network-list no

    by default no

    Split-dns no

    Disable dhcp Intercept 255.255.255.255

    disable secure authentication unit

    disable authentication of the user

    user-authentication-idle-timeout 30

    disable the IP-phone-bypass

    disable the leap-bypass

    allow to NEM

    Dungeon-client-config backup servers

    MSIE proxy server no

    MSIE-proxy method non - change

    Internet Explorer proxy except list - no

    Disable Internet Explorer-proxy local-bypass

    disable the NAC

    NAC-sq-period 300

    NAC-reval-period 36000

    NAC-by default-acl no

    address pools no

    enable Smartcard-Removal-disconnect

    the firewall client no

    rule of access-client-none

    WebVPN

    url-entry functions

    HTML-content-filter none

    Home page no

    4 Keep-alive-ignore

    gzip http-comp

    no filter

    list of URLS no

    value of customization DfltCustomization

    port - forward, no

    port-forward-name value access to applications

    SSO-Server no

    value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information

    SVC no

    SVC Dungeon-Installer installed

    SVC keepalive no

    generate a new key SVC time no

    method to generate a new key of SVC no

    client of dpd-interval SVC no

    dpd-interval SVC bridge no

    deflate compression of SVC

    internal group XXXXXX strategy

    attributes of XXXXXX group policy

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelall

    Split-tunnel-network-list no

    XXXXXX G910DDfbV7mNprdR encrypted privilege 15 password username

    username password encrypted XXXXXX privilege 0 5p9CbIe7WdF8GZF8

    attributes of username XXXXXX

    Strategy Group-VPN-XXXXXX

    username privilege 15 encrypted password cRQbJhC92XjdFQvb XXXXX

    tunnel-group XXXXXX type ipsec-ra

    attributes global-tunnel-group XXXXXX

    address VPNPOOL pool

    Group Policy - by default-XXXXXX

    tunnel-group ipsec-attributes XXXXXX

    pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    inspect the icmp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:a8fbb51b0a830a4ae823826b28767f23

    : end

    ciscoasa #.

    Thanks in advance!

    fbela

    config #no nat (inside) 1 10.0.0.0 255.255.255.0< this="" is="" not="">

    Add - config #same-Security-permit intra-interface

    #access - extended list allowed sheep ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

    #nat (inside) 0 access-list sheep

    Please add and test it.

    Thank you

    Ajay

  • Cisco AnyConnect VPN Client maintains reconnection

    Hello

    We have recently installed an ASA5505 and activated the VPN access.

    Two of my colleagues have no problems connecting to the VPN using Cisco AnyConnect VPN Client, but I do.

    I am still disconnected after a few seconds with the message:

    "A VPN reconnect gave rise to different configuration settings. VPN network interface is to be reset. Applications using the private network may be required to restart. »

    Cisco AnyConnect VPN Client Version 2.5.2019

    I work with Windows 7 but the same thing happens when I try to connect using my computer that is running Windows Vista.

    My colleagues also using Win7

    I also tried to disable the Windows Firewall.

    Any help would be appreciated.

    Best regards

    Peter

    TAC has been able to solve the problem.   For webvpn mtu changed default from 1406 to 1200.

    Not sure why 2 other ASAs we work very well otherwise though!

    WebVPN
    SVC mtu 1200

  • Cisco VPN Client cannot ping from LAN internal IP

    Hello

    I apologize in advance for my lack of knowledge about it, but I got a version of the software running ASA 5510 7.2 (2) and has been invited to set up a site with a client, I managed to get this configured and everything works fine. In addition, I created a group of tunnel ipsec-ra for users to connect to a particular server 192.168.10.100/24 remote, even if the connection is made successfully, I can not ping any IP on the LAN 192.168.10.0/24 located behind the ASA and when I ping inside the interface on the ASA it returns the public IP address of the external interface.

    If someone out there could give me a little push in the right direction, it would be much appreciated! This is the current configuration of the device.

    Thanks in advance.

    : Saved

    :

    ASA Version 7.2 (2)

    !

    hostname ciscoasa5510

    domain.local domain name

    activate the password. 123456789 / encrypted

    names of

    !

    interface Ethernet0/0

    nameif outside

    security-level 0

    PPPoE client vpdn group ISP

    12.34.56.789 255.255.255.255 IP address pppoe setroute

    !

    interface Ethernet0/1

    nameif inside

    security-level 100

    IP 192.168.10.1 255.255.255.0

    !

    interface Ethernet0/2

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Ethernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    nameif management

    security-level 100

    IP 192.168.1.1 255.255.255.0

    management only

    !

    passwd encrypted 123456789

    passive FTP mode

    clock timezone GMT/UTC 0

    summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00

    DNS server-group DefaultDNS

    domain.local domain name

    permit outside_20_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124

    permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124

    access-list Split_Tunnel_List note the network of the company behind the ASA

    Split_Tunnel_List list standard access allowed 192.168.10.0 255.255.255.0

    pager lines 24

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    management of MTU 1500

    IP local pool domain_vpn_pool 192.168.11.1 - 192.168.11.254 mask 255.255.255.0

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 522.bin

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 0.0.0.0 0.0.0.0

    Route outside 0.0.0.0 0.0.0.0 12.34.56.789 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout, uauth 0:05:00 absolute

    internal domain_vpn group policy

    attributes of the strategy of group domain_vpn

    value of 212.23.3.100 DNS server 212.23.6.100

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list Split_Tunnel_List

    username domain_ra_vpn password 123456789 encrypted

    username domain_ra_vpn attributes

    VPN-group-policy domain_vpn

    encrypted utilisateur.123456789 password username

    encrypted utilisateur.123456789 password username

    privilege of username user password encrypted passe.123456789 15

    encrypted utilisateur.123456789 password username

    the ssh LOCAL console AAA authentication

    AAA authentication enable LOCAL console

    Enable http server

    http 192.168.1.0 255.255.255.0 management

    http 192.168.10.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto-map dynamic outside_dyn_map 20 set pfs

    Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

    card crypto outside_map 20 match address outside_20_cryptomap

    peer set card crypto outside_map 20 987.65.43.21

    outside_map crypto 20 card value transform-set ESP-3DES-SHA

    3600 seconds, duration of life card crypto outside_map 20 set - the security association

    map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    aes-256 encryption

    sha hash

    Group 5

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    tunnel-group 987.65.43.21 type ipsec-l2l

    IPSec-attributes tunnel-group 987.65.43.21

    pre-shared-key *.

    tunnel-group domain_vpn type ipsec-ra

    tunnel-group domain_vpn General-attributes

    address domain_vpn_pool pool

    Group Policy - by default-domain_vpn

    domain_vpn group of tunnel ipsec-attributes

    pre-shared-key *.

    Telnet 192.168.10.0 255.255.255.0 inside

    Telnet timeout 5

    Console timeout 0

    VPDN group ISP request dialout pppoe

    VPDN group ISP localname [email protected] / * /

    VPDN group ISP ppp authentication chap

    VPDN username [email protected] / * / password *.

    dhcpd dns 212.23.3.100 212.23.6.100

    dhcpd lease 691200

    dhcpd ping_timeout 500

    domain.local domain dhcpd

    !

    dhcpd address 192.168.10.10 - 192.168.10.200 inside

    dhcpd allow inside

    !

    management of 192.168.1.2 - dhcpd address 192.168.1.254

    enable dhcpd management

    !

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    !

    global service-policy global_policy

    context of prompt hostname

    Cryptochecksum:1234567890987654321

    : end

    Hello

    Seems to me that you are atleast lack the NAT0 configuration for your VPN Client connection.

    This configuration is intended to allow the VPN Client to communicate with the local network with their original IP addresses. Although the main reason that this is necessary is to avoid this traffic to the normal rule of dynamic PAT passing this traffic and that traffic is falling for the corresponding time.

    You can add an ACL rule to the existing ACL NAT0, you have above and the NAT configuration should go next

    Add this

    permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

    Hope this helps

    Let me know how it goes

    -Jouni

  • AnyConnect VPN client authentication using certificates

    Guys, I'm trying to configure my ASA5505 to authenticate the AnyConnect VPN clients using certificates. I have 'Certificates' defined as my method of authentication in my AnyConnect connection profile (see screenshot), but I get 'Certificate Validation failure' whenever I try to connect. The certificate I want to use is a computer issued by my CA certificate company root (Windows Server 2008 running Active Directory Certificate Services). Screenshot of certificate is attached. I added the root certificate on the SAA, and I tried all kinds of combinations by using the corresponding certificate in the AnyConnect Client profile. Each attempt failed, and I'm having no luck finding documentation on how to proceed. Any help would be greatly appreciated!

    Hello Shaun,

    The problem you're describing, not be able to authenticate through certificate through Microsoft Internet Explorer, is the fact that the certificate is in the computer store.  You do not want to confirm with Microsoft, but, I understand that only Microsoft Internet users explore the user store, this certificate is not available to attend the ASA via the Internet browser.

    -Craig

  • Windows - Internet access, no split Tunnel L2TP VPN Clients does not

    Greetings!

    I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.

    I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.

    Here is the configuration:

    : Saved
    :
    ASA Version 1.0000 11
    !
    SGC hostname
    domain somewhere.com
    names of
    COMMENTS COMMENTS LAN 192.168.2.0 name description
    name 75.185.129.13 description of SGC - external INTERNAL ASA
    name 172.22.0.0 description of SITE1-LAN Ohio management network
    description of SITE2-LAN name 172.23.0.0 Lake Club Network
    name 172.24.0.0 description of training3-LAN network Southwood
    description of training3 - ASA 123.234.8.124 ASA Southwoods name
    INTERNAL name 192.168.10.0 network Local INTERNAL description
    description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
    description of Apollo name 192.168.10.4 INTERNAL domain controller
    description of DHD name 192.168.10.2 Access Point #1
    description of GDO name 192.168.10.3 Access Point #2
    description of Odyssey name 192.168.10.5 INTERNAL Test Server
    CMS internal description INTERNAL ASA name 192.168.10.1
    name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
    description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
    description of training3-VOICE name Southwood Voice Network 10.1.0.0
    name 172.25.0.0 description of training3-WIFI wireless Southwood
    !
    interface Vlan1
    nameif outside
    security-level 0
    IP address dhcp setroute
    !
    interface Vlan2
    nameif INSIDE
    security-level 100
    255.255.255.0 SGC-internal IP address
    !
    interface Vlan3
    nameif COMMENTS
    security-level 50
    IP 192.168.2.1 255.255.255.0
    !
    interface Ethernet0/0
    Time Warner Cable description
    !
    interface Ethernet0/1
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    interface Ethernet0/2
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    interface Ethernet0/3
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    interface Ethernet0/4
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    interface Ethernet0/5
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    interface Ethernet0/6
    Description for Wireless AP Trunk Port
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    interface Ethernet0/7
    Description for Wireless AP Trunk Port
    switchport access vlan 2
    switchport trunk allowed vlan 2-3
    switchport vlan trunk native 2
    switchport mode trunk
    !
    boot system Disk0: / asa821-11 - k8.bin
    Disk0: / config.txt boot configuration
    passive FTP mode
    clock timezone IS - 5
    clock to summer time EDT recurring
    DNS domain-lookup outside
    INTERNAL DNS domain-lookup
    DNS domain-lookup GUEST
    DNS server-group DefaultDNS
    Name-Server 4.2.2.2
    domain somewhere.com
    permit same-security-traffic inter-interface
    permit same-security-traffic intra-interface
    DM_INLINE_TCP_1 tcp service object-group
    EQ port 3389 object
    port-object eq www
    EQ object of the https port
    EQ smtp port object
    the DM_INLINE_NETWORK_1 object-group network
    network-object SITE1-LAN 255.255.0.0
    network-object SITE2-LAN 255.255.0.0
    network-object training3-LAN 255.255.0.0
    object-group training3-GLOBAL network
    Southwood description Global Network
    network-object training3-LAN 255.255.0.0
    network-object training3-VOICE 255.255.0.0
    network-object training3-WIFI 255.255.0.0
    DM_INLINE_TCP_2 tcp service object-group
    EQ port 5900 object
    EQ object Port 5901
    object-group network INTERNAL GLOBAL
    Description Global INTERNAL Network
    network-object INTERNAL 255.255.255.0
    network-object INTERNALLY-VPN 255.255.255.0
    access-list outside_access note Pings allow
    outside_access list extended access permit icmp any CMS-external host
    access-list outside_access note that VNC for Camille
    outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
    access-list outside_access note INTERNAL Services
    outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
    DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
    access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
    access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
    access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
    access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
    access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
    access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
    access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
    no pager
    Enable logging
    exploitation forest asdm warnings
    Debugging trace record
    Outside 1500 MTU
    MTU 1500 INTERNAL
    MTU 1500 COMMENTS
    192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    ASDM image disk0: / asdm - 623.bin
    enable ASDM history
    ARP timeout 14400
    Global 1 interface (outside)
    (INTERNAL) NAT 0 access-list sheep
    NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
    NAT (GUEST) 1 0.0.0.0 0.0.0.0
    5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
    3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
    public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
    public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
    public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
    5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
    Access-group outside_access in interface outside
    Timeout xlate 0:05:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    RADIUS protocol AAA-server Apollo
    Apollo (INTERNAL) AAA-server Apollo
    Timeout 5
    key *.
    AAA authentication enable LOCAL console
    the ssh LOCAL console AAA authentication
    AAA authentication LOCAL telnet console
    AAA authentication http LOCAL console
    Enable http server
    http 0.0.0.0 0.0.0.0 INTERNAL
    http 0.0.0.0 0.0.0.0 COMMENTS
    No snmp server location
    No snmp Server contact
    Community SNMP-server
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
    Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
    correspondence address 1 card crypto outside_map INTERNAL SITE1
    card crypto outside_map 1 set of peer SITE1 - ASA
    card crypto outside_map 1 set of transformation-ESP-3DES-SHA
    address for correspondence card crypto outside_map 2 INTERNAL training3
    outside_map 2 peer training3 - ASA crypto card game
    card crypto outside_map 2 game of transformation-ESP-3DES-SHA
    address for correspondence outside_map 3 card crypto INTERNAL SITE2
    game card crypto outside_map 3 peers SITE2 - ASA
    card crypto outside_map 3 game of transformation-ESP-3DES-SHA
    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    outside_map interface card crypto outside
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    delimiter group @.
    Telnet training3 - ASA 255.255.255.255 outside
    Telnet SITE2 - ASA 255.255.255.255 outside
    Telnet SITE1 - ASA 255.255.255.255 outside
    Telnet 0.0.0.0 0.0.0.0 INTERNAL
    Telnet 0.0.0.0 0.0.0.0 COMMENTS
    Telnet timeout 60
    SSH enable ibou
    SSH training3 - ASA 255.255.255.255 outside
    SSH SITE2 - ASA 255.255.255.255 outside
    SSH SITE1 - ASA 255.255.255.255 outside
    SSH 0.0.0.0 0.0.0.0 INTERNAL
    SSH 0.0.0.0 0.0.0.0 COMMENTS
    SSH timeout 60
    Console timeout 0
    access to the INTERNAL administration
    Hello to tunnel L2TP 100
    interface ID client DHCP-client to the outside
    dhcpd dns 4.2.2.1 4.2.2.2
    dhcpd ping_timeout 750
    dhcpd outside auto_config
    !
    address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
    dhcpd Apollo Odyssey interface INTERNAL dns
    dhcpd somewhere.com domain INTERNAL interface
    interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
    enable dhcpd INTERNAL
    !
    dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
    dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
    enable dhcpd COMMENTS
    !

    a basic threat threat detection
    statistical threat detection port
    Statistical threat detection Protocol
    Statistics-list of access threat detection
    a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
    NTP server 192.43.244.18 prefer external source
    WebVPN
    allow outside
    CSD image disk0:/securedesktop-asa-3.4.2048.pkg
    SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
    SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
    enable SVC
    Group Policy DefaultRAGroup INTERNAL
    attributes of Group Policy DefaultRAGroup
    Server DNS 192.168.10.4 value
    Protocol-tunnel-VPN l2tp ipsec
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
    value by default-domain somewhere.com
    Group Policy DefaultWEBVPNGroup INTERNAL
    attributes of Group Policy DefaultWEBVPNGroup
    VPN-tunnel-Protocol webvpn
    Group Policy DefaultL2LGroup INTERNAL
    attributes of Group Policy DefaultL2LGroup
    Protocol-tunnel-VPN IPSec l2tp ipsec
    Group Policy DefaultACVPNGroup INTERNAL
    attributes of Group Policy DefaultACVPNGroup
    VPN-tunnel-Protocol svc
    attributes of Group Policy DfltGrpPolicy
    value of 192.168.10.4 DNS Server 4.2.2.2
    VPN - 25 simultaneous connections
    VPN-idle-timeout no
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
    value by default-domain somewhere.com
    the value INTERNAL VPN address pools
    chip-removal-disconnect disable card
    WebVPN
    SVC keepalive no
    client of dpd-interval SVC no
    dpd-interval SVC bridge no
    value of customization DfltCustomization
    attributes global-tunnel-group DefaultRAGroup
    VPN INTERNAL address pool
    Group Policy - by default-DefaultRAGroup
    IPSec-attributes tunnel-group DefaultRAGroup
    pre-shared-key *.
    Disable ISAKMP keepalive
    tunnel-group DefaultRAGroup ppp-attributes
    No chap authentication
    no authentication ms-chap-v1
    ms-chap-v2 authentication
    attributes global-tunnel-group DefaultWEBVPNGroup
    VPN INTERNAL address pool
    Group Policy - by default-DefaultWEBVPNGroup
    tunnel-group 123.234.8.60 type ipsec-l2l
    IPSec-attributes tunnel-group 123.234.8.60
    pre-shared-key *.
    tunnel-group 123.234.8.124 type ipsec-l2l
    IPSec-attributes tunnel-group 123.234.8.124
    pre-shared-key *.
    tunnel-group 123.234.8.189 type ipsec-l2l
    IPSec-attributes tunnel-group 123.234.8.189
    pre-shared-key *.
    type tunnel-group DefaultACVPNGroup remote access
    attributes global-tunnel-group DefaultACVPNGroup
    VPN INTERNAL address pool
    Group Policy - by default-DefaultACVPNGroup
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the netbios
    inspect the rsh
    inspect the rtsp
    inspect the skinny
    inspect esmtp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect the sip
    inspect xdmcp
    inspect the http
    inspect the they
    !
    global service-policy global_policy
    context of prompt hostname
    Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
    : end
    ASDM image disk0: / asdm - 623.bin
    ASDM location Camille 255.255.255.255 INTERNAL
    ASDM location INTERNAL CGT-external 255.255.255.255
    ASDM location INTERNAL SITE1-LAN 255.255.0.0
    ASDM location INTERNAL SITE2-LAN 255.255.0.0
    ASDM location INTERNAL training3-LAN 255.255.0.0
    ASDM location INTERNAL training3 - ASA 255.255.255.255
    ASDM location INTERNAL GDO 255.255.255.255
    ASDM location INTERNAL SITE1 - ASA 255.255.255.255
    ASDM location INTERNAL SITE2 - ASA 255.255.255.255
    ASDM location INTERNAL training3-VOICE 255.255.0.0
    ASDM location puppy 255.255.255.255 INTERNAL
    enable ASDM history

    I should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.

    You must configure * intercept-dhcp enable * in your group strategy:

    attributes of Group Policy DefaultRAGroup

    attributes of Group Policy DefaultRAGroup

    Server DNS 192.168.10.4 value
    Protocol-tunnel-VPN l2tp ipsec
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
    value by default-domain somewhere.com

    Intercept-dhcp enable

    -Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked.  It is located on the Advanced tab of VPN client TCP/IP properties.   Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.

    Alex

  • ASA5505 - remove VPN connections

    Hey all, have a simple question.

    the following page indicates it can handle up to 10 connections vpn with a basic license. This means that we can configure only 10 credentials of the vpn user/pass? or, we can create, for example 50 accounts user/pass, but only 10 can remote in at the same time.

    http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

    Thanks for the help.

    -robert

    Robert,

    That's right... 10 ways to connections VPN is a vpn connections simultaneous maximum with base... license you can create as many users in the local database asa but only 10 RA VPN client sessions can be established, however, that this column includes also the VPN L2L, say if you have 1 site-to-site vpn and 9 RA vpn which has a total of 10 sessions VPN.

    Concerning

  • Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

    I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

    Thank you

    interface Ethernet0/0

    Speed 100

    full duplex

    nameif outside

    security-level 0

    IP x.x.x.x 255.255.255.240

    !

    interface Ethernet0/1

    Speed 100

    full duplex

    nameif inside

    security-level 100

    IP 10.88.10.254 255.255.255.0

    !

    interface Management0/0

    Shutdown

    nameif management

    security-level 0

    no ip address

    !

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    network of the PAT_to_Outside_ClassA object

    10.88.0.0 subnet 255.255.0.0

    network of the PAT_to_Outside_ClassB object

    subnet 172.16.0.0 255.240.0.0

    network of the PAT_to_Outside_ClassC object

    Subnet 192.168.0.0 255.255.240.0

    network of the LocalNetwork object

    10.88.0.0 subnet 255.255.0.0

    network of the RemoteNetwork1 object

    Subnet 192.168.0.0 255.255.0.0

    network of the RemoteNetwork2 object

    172.16.10.0 subnet 255.255.255.0

    network of the RemoteNetwork3 object

    10.86.0.0 subnet 255.255.0.0

    network of the RemoteNetwork4 object

    10.250.1.0 subnet 255.255.255.0

    network of the NatExempt object

    10.88.10.0 subnet 255.255.255.0

    the Site_to_SiteVPN1 object-group network

    object-network 192.168.4.0 255.255.254.0

    object-network 172.16.10.0 255.255.255.0

    object-network 10.0.0.0 255.0.0.0

    outside_access_in deny ip extended access list a whole

    inside_access_in of access allowed any ip an extended list

    11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

    outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

    mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

    NAT static NatExempt NatExempt of the source (indoor, outdoor)

    NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

    NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

    !

    network of the PAT_to_Outside_ClassA object

    NAT dynamic interface (indoor, outdoor)

    network of the PAT_to_Outside_ClassB object

    NAT dynamic interface (indoor, outdoor)

    network of the PAT_to_Outside_ClassC object

    NAT dynamic interface (indoor, outdoor)

    Access-group outside_access_in in interface outside

    inside_access_in access to the interface inside group

    Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

    dynamic-access-policy-registration DfltAccessPolicy

    Sysopt connection timewait

    Service resetoutside

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto-map dynamic dynmap 10 set pfs

    Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

    life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

    Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

    Crypto-map dynamic dynmap 10 the value reverse-road

    card crypto mymap 1 match address outside_1_cryptomap

    card crypto mymap 1 set counterpart x.x.x.x

    card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

    card crypto mymap 86400 seconds, 1 lifetime of security association set

    map mymap 1 set security-association life crypto kilobytes 4608000

    map mymap 100-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    crypto isakmp identity address

    Crypto isakmp nat-traversal 30

    Crypto ikev1 allow outside

    IKEv1 crypto ipsec-over-tcp port 10000

    IKEv1 crypto policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 1

    life 86400

    IKEv1 crypto policy 50

    preshared authentication

    the Encryption

    md5 hash

    Group 2

    life 86400

    IKEv1 crypto policy 60

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 70

    preshared authentication

    aes-256 encryption

    sha hash

    Group 1

    life 86400

    IKEv1 crypto policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal BACKDOORVPN group policy

    BACKDOORVPN group policy attributes

    value of VPN-filter 11

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelall

    BH.UK value by default-field

    type tunnel-group BACKDOORVPN remote access

    attributes global-tunnel-group BACKDOORVPN

    address pool Admin_Pool

    Group Policy - by default-BACKDOORVPN

    IPSec-attributes tunnel-group BACKDOORVPN

    IKEv1 pre-shared-key *.

    tunnel-group x.x.x.x type ipsec-l2l

    tunnel-group ipsec-attributes x.x.x.x

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    Excellent.

    Evaluate the useful ticket.

    Thank you

    Rizwan James

  • Issue of ASA VPN client

    Hello.

    I have a question about a connection between an asa5505-sec-bun-k9 (who acts as easy VPN client) and an EASY VPN server.

    The connection with the easy VPN server is OK, but I can't connect to the internet and create VPN for my ASA5505 connections when I activated the feature.

    Is this a normal phenomenon with Easy VPN active customer?

    Cool

    Please, note useful

  • VPN client behind ok asa pix but no asa

    Hi all

    I was faced with a newly installed asa5505 couple. We can use the vpnclient in devices, but not behind another asa. Behind the asa same we can vpn for previous installations of pix. But when we go to other asa installs, we get the regular creation of translation failed for protocol 50.

    We have activated, isakmp, nat-traversal, udp 4500 and udp 10000. If the fault is at the other end, even if the error shows in this end?

    Anyone who is willing to help me with this?

    see you soon / Peter

    You do not allow protocol 50 - ESP through the firewall. The remote end VPN are trying to create a VPN in mode 'Hand' is not "Aggressive" mode as VPN clients.

    Add the below and test again: -.

    permit for outside_access_in to access extensive list of 6 esp a whole line

    HTH.

  • connect Cisco VPN client v5 to asa 5505

    I have remote vpn configuration issues between ASA5505 and Cisco VPN client v5. Successfully, I can establish a connection between the client Vpn and ASA and receive the IP address of the ASA. Statistical customer VPN windows shows that packets are sent and encrypted but none of the packages is received/decrypted.

    Cannot ping asa 5505

    Any ideas on what I missed?

    Try adding...

    ISAKMP nat-traversal crypto

    In addition, you cannot ping the inside interface of the ASA vpn without this command...

    management-access inside

    Please evaluate the useful messages.

  • Why my VPN clients cannot access network drives and resources?

    I have a cisco asa 5505 configured to be a VPN gateway. I can dial using the anyconnect VPN client. The remote user is assigned an IP address to my specifications. However... The remote user cannot access network such as disks in network resources or the fax server. I've done everything I can to set the right settings NAT and ACLs, but in vain. I write my config... If someone can track down the problem. It would be appreciated!

    : Saved

    :

    ASA Version 8.2 (5)

    !

    ciscoasa hostname

    Cisco domain name

    activate the password xxxxxxxxxxxxx

    passwd xxxxxxxxxxxxxxxxx

    names of

    name 68.191.xxx.xxx outdoors

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.201.200 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address outside 255.255.255.0

    !

    passive FTP mode

    DNS domain-lookup outside

    DNS lookup field inside

    DNS server-group DefaultDNS

    192.168.201.1 server name

    Cisco domain name

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    object-group Protocol TCPUDP

    object-protocol udp

    object-tcp protocol

    object-group network obj - 192.168.201.0

    FREE access-list extended ip 192.168.201.0 NAT allow 255.255.255.0 192.168.201.0 255.255.255.0

    NAT-FREE 192.168.202.0 permits all ip extended access list 255.255.255.0

    FREE access-list extended ip 192.168.202.0 NAT allow 255.255.255.0 any

    Extended access list-NAT-FREE enabled a whole icmp

    allow any scope to an entire ip access list

    allow any scope to the object-group TCPUDP an entire access list

    allow any scope to an entire icmp access list

    inside_access_in of access allowed any ip an extended list

    inside_access_in list extended access allow TCPUDP of object-group a

    inside_access_in list extended access permit icmp any one

    outside_access_in of access allowed any ip an extended list

    outside_access_in list extended access allow TCPUDP of object-group a

    outside_access_in list extended access permit icmp any one

    Standard access list DefaultRAGroup_splitTunnelAcl allow 192.168.201.0 255.255.255.0

    access extensive list ip 192.168.202.0 inside_nat0_outbound allow 255.255.255.0 192.168.201.0 255.255.255.0

    inside_nat0_outbound list extended access permit icmp any one

    inside_nat0_outbound_1 of access allowed any ip an extended list

    pager lines 24

    Enable logging

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    mask 192.168.202.1 - 192.168.202.50 255.255.255.0 IP local pool KunduVPN

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    Global 1 interface (outside)

    NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access

    NAT (inside) 1 192.168.201.0 255.255.255.0

    Access-group outside_access_in in interface outside

    inside_access_in access to the interface inside group

    Route inside 0.0.0.0 0.0.0.0 192.168.201.1 1

    Route inside 0.0.0.0 255.255.255.255 outdoor 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    Enable http server

    http 192.168.201.0 255.255.255.0 inside

    http 0.0.0.0 0.0.0.0 outdoors

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

    Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    Crypto ca trustpoint ASDM_TrustPoint0

    registration auto

    name of the object CN = ciscoasa

    Keypairs xxx

    Proxy-loc-transmitter

    Configure CRL

    XXXXXXXXXXXXXXXXXXXXXXXX

    quit smoking

    crypto ISAKMP allow outside

    crypto ISAKMP allow inside

    crypto ISAKMP policy 10

    authentication crack

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 20

    authentication rsa - sig

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 40

    authentication crack

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 50

    authentication rsa - sig

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 60

    preshared authentication

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 70

    authentication crack

    aes encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 80

    authentication rsa - sig

    aes encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 100

    authentication crack

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 110

    authentication rsa - sig

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 120

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 130

    authentication crack

    the Encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 140

    authentication rsa - sig

    the Encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 150

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd outside auto_config

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    SSL-trust outside ASDM_TrustPoint0 point

    WebVPN

    allow outside

    allow inside

    SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image

    enable SVC

    tunnel-group-list activate

    internal DefaultRAGroup group strategy

    attributes of Group Policy DefaultRAGroup

    value of 192.168.201.1 DNS server

    VPN-tunnel-Protocol svc webvpn

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl

    Cisco by default field value

    attributes of Group Policy DfltGrpPolicy

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    WebVPN

    SVC request enable

    internal KunduVPN group strategy

    attributes of Group Policy KunduVPN

    WINS server no

    value of 192.168.201.1 DNS server

    VPN-tunnel-Protocol svc webvpn

    Cisco by default field value

    username xxxx

    username xxxxx

    VPN-group-policy DfltGrpPolicy

    attributes global-tunnel-group DefaultRAGroup

    address VPNIP pool

    Group Policy - by default-DefaultRAGroup

    IPSec-attributes tunnel-group DefaultRAGroup

    pre-shared key *.

    tunnel-group DefaultRAGroup ppp-attributes

    ms-chap-v2 authentication

    type tunnel-group KunduVPN remote access

    attributes global-tunnel-group KunduVPN

    address (inside) VPNIP pool

    address pool KunduVPN

    authentication-server-group (inside) LOCAL

    Group Policy - by default-KunduVPN

    tunnel-group KunduVPN webvpn-attributes

    enable KunduVPN group-alias

    allow group-url https://68.191.xxx.xxx/KunduVPN

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:c0e4540d4a07f2c544f0eddb653627cc

    : end

    don't allow no asdm history

    Hello

    What is the IP address of the hosts/servers LAN Gateway?

    If this is not the ASA 'inside' interface IP address then I assume that the problem with VPN is simply routing.

    For example, if your hosts/servers LAN wireless LAN gateway router then the following would happen to your Clients VPN connections.

    • Forms of customers login VPN users through configuring wireless routers static PAT (Port Forward) to interface "inside" ASA
    • Client VPN sends traffic through the VPN to ASA and again the host of the server or LAN.
    • Host/server LAN sees the connection from a network other than the LAN (192.168.202.0/24) and therefore to forward traffic to the default gateway that would likely be the wireless router.
    • Wireless router has no route to the network 192.168.202.0/24 (VPN Pool) and therefore uses its default route to the external network to forward traffic.
    • Client VPN host never received the traffic back as transmitted sound on the external network and abandoned by the ISP

    So if the above assumption is correct, then you would at least need a configuration of the road on the wireless router that tells the device to transfer traffic to the network 192.168.202.0/24 to the 192.168.201.200 gateway IP address (which is the SAA)

    I would like to know if the installation is as described above.

    -Jouni

Maybe you are looking for

  • I have iphone 4s, icloud locked trying to get in touch with the owner to give it back or unlock it he won't talk, it's gsx is useful in this case? owner is not interested in the phone!

    I have iphone 4s, icloud locked trying to get in touch with the owner to give it back or unlock it he won't talk, it's gsx is useful in this case? owner is not interested in the phone! and he has been blocked me on whatsapp about 6 times when I tried

  • Completely disable the presentation of data

    Hello I set the following preferences: user_pref ("datareporting.healthreport.service.enabled", false);user_pref ("datareporting.healthreport.uploadEnabled", false);user_pref ("datareporting.policy.dataSubmissionEnabled", false);user_pref ("toolkit.t

  • node of expression

    What is the correct syntax for an exhibitor with the node of expression?I looked in the help of LabVIEW, and it seemed that it was the ' ^' character. except that does not appear to be correct: The correct output should be 2, but LabVIEW returns 3.

  • Helps Update - Service Pack 3

    Try to install a wireless router. Message says that I have to download Service Pack 3.  My automatic updates must be turned on, but when I check Control Panel and try to turn it on, says go to security settings that I make and still cannot fix.  Any

  • Maximum of Acer Aspire 5720Z RAM

    I worked on my pen-brother 5720Z Acer and I read that the chipset is limited to 2 GB. I upgraded to 2 in 2009. I want to confirm that there is no way to pass to 4 GB (3.5 inches with W7 32 bit OS). The BIOS is 1.45. Most of the posts on this point an