ASBL voice and data simultaneously

Similar Questions

• Simultaneous voice and data on Verizon?

  OK, you can now pre-order the phone, and yet I saw no confirmation one way or another as to if the Moto X play supports simultaneous voice and data on Verizon. I tweeted Verizon today and they claim that they do not have the specs of the phone.

  I can't believe anyone, namely, Motorola and Verizon, are able to answer this fundamental question.

  My Moto X (2014) can not STILL can't do, so I am wary to this model as well and rightly.

  Can we please get a definitive answer?

  Yes, you can get simultaneous voice and data on Verizon.

• Configure the VLAN voice and data in CISCO SF 300 8 P

  I have a couple of Cisco SF 300 8 P and P 24 switches. I have voice and data VLANS configured as:

  Data VLAN: default 145.17.59.0/24

  Voice VLANS: VLAN 20 172.22.20.0/24

  I have different DHCP servers regarding the data VLAN, we have a physical server that is configured for 145.17.59 * extended IP and Voice VLAN DHCP Server is configured as a router gateway with option 150.

  This configuration works very well with other cisco 2960 switches and 3750 etc. except CISCO SF 300 8 P and 24 p. I tried to set up the voice and data VLAN in these CISCO switches so that phone CISCO (model 6941) should get IP of the VLAN voice and PC should get the IP address of the DHCP server on the data VLAN. I tried several techniques such as LLDP, Port-to-VLAN Config etc.

  Can anyone please guide me / help on this.

  Kind regards
  A K.M.Sayeed

  Hi A.K.M., with Cisco phones you should be able to define simply automatic voice VLAN to be VLAN20.

  ID of the vlan 20 voices

  You must ensure CDP or LLDP is enabled as well. I would check in the web GUI. DHCP for phones can come from a DHCP server on a port access VLAN20 switch, or you can use dhcp for assistance to redirect DHCP server elsewhere.

  If you prefer or you have problems with the CDP or LLDP, you can also program the ports as trunks and add the tag VLAN 20 for them.  In this scenario, you need to ensure inter - vlan routing works and phones that download the file config with corrrect VLAN config.

  These switches do not run ios, so they are similar, but different from the catalyst switches that you mentioned.

  -remember messages useful rate.

• Trouble with the voice and data Vlan vlan translate between CT3905 and SF300 - 24 p

  Hey actually, we have the solution to monitoring of implementation with CT3905 phone, SF300 - switches 24 p cameras and AIR-AP1041N Access Points

  

  We have the problem with the vlan tag in SF300 switch ports - 24 p we can´t tag vlan of the voice and data VLANs on the same port on SF300 - 24 p it is Possible or we must dedicate a port for each VLAN or ussing the same data segment of VLANs and vlan voice?

  Someone has an answer or technical documentation that can help us

  Best regards

  First of all,

  Please disable lldp transmit in SF 300 switch.

  The command is "no lldp transmitted."

  After you disable check the following steps.

  https://supportforums.Cisco.com/docs/doc-27005

  facing the same problem with cisco SG 300 and 3905 ip phone switch.

  And nested thing was my 7945 and 6941 phones use to work properly, without above configuration.

  Cisco 3905 became not vlan Ip address votes and even if I put static, it did not work.

  After a long struggle, I was able to solve the problem. Now both phone and system work fine in the same port.

  Samantha

• Lack of voice and data at the same time kills me

  After using a treo 750 (WM 6.1) on att for the past three years, I guess I did not realize the advantage of ATT and gsm in general.  There are many drawbacks... mainly pricing for simple accounts (However their family plan was directly comparable to those of sprint).  I constantly try to use data applications while talking on the phone without success.  I started thinking that I could do without, but a week later, I still really really miss.  My wife did too... because she's I usually give directions or any other web information while on the phone.  There is nothing like view google satellite map to help someone make sure they are in the right place... "see a big tree on your right with a large Brown building behind it, Yes, it's that one" does anyone else have this feeling?  WiFi is not an option for me most of the time.

  Voice and data at the same time is not available when using any CDMA network due to network constraints. This is true for all types of phones, not only Palm or not only the Pre. Your example of electronic control or by using google maps, the gps data that can be stored before you activate the call. try to browse the web while making a call and try to go to a web page, you have never visited before, so that you know, that he cannot be a version collected page.

• Problem blackBerry Smartphones on the use of the voice and data

  Hello

  When we use the Blackberry Desktop Software for backup/restore data from one phone to another, will check voice and data usage in the session "peripheral and buyer information - status remorse" also be restored from the old phone or affected by synchronization? Or will they count just use since the first use of the new phone?

  Harold Lee

  I have to admit, I am not an expert on this subject, but that is my impression.  Once you get the new phone running, your meter would reset to zero on this phone.

• How can I get voice and data to work with the ASA 5505?

  Here's the issue I'm having.   Can I get a Cisco 7940 to work behind one site to another configured ASA 5505 and I can also get data to work behind it.  However, when I try to create a separate Vlan for voice and data, it does not work.  Our voice VLANs on our remote sites are 172.30 and data are 172.31, when I put the inside interface with 172.31 data will work and when I on it 172.30 voice will work.  I upgraded to a security more license and tried vlan3 created as voice.  I have the data to the top and work but I can't get vlan3 to work.   Any help would be greatly appreciated.  Thank you

  Here is my current config:

  hostname TESTvpn
  activate the password xxxxx

  passwd xxxxx

  username admin password xxxxx privilege 15

  name Corp_LAN 10.0.0.0
  name 192.168.64.0 Corp_Voice
  name 172.31.155.0 TESTvpn

  object-group network SunVoyager
  host of the object-Network 64.70.8.160
  host of the object-Network 64.70.8.242

  the Corp_Networks object-group network
  network-object Corp_LAN 255.0.0.0
  object-network Corp_Voice 255.255.255.0

  interface vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  No tap

  interface vlan1
  nameif inside
  security-level 100
  IP 172.31.155.1 255.255.255.0
  No tap

  interface vlan3
  nameif Corp_Voice
  security-level 100
  IP 172.30.155.1 255.255.255.0
  No tap

  output
  interface Ethernet0/0
  switchport access vlan 2
  No tap

  interface Ethernet0/7
  switchport access vlan 3
  No tap

  output

  dhcpd allow inside
  dhcpd address 172.31.155.10 - 172.31.155.30 inside
  dhcpd dns 10.10.10.7 10.10.10.44 interface inside
  dhcpd sun.ins area inside interface
  dhcpd allow inside

  enable Corp_Voice dhcpd
  dhcpd address 172.30.155.10 - 172.30.155.30 Corp_Voice
  dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
  dhcpd interface of sun.ins of the Corp_Voice domain
  enable Corp_Voice dhcpd
  dhcpd option 150 ip 192.168.64.4 192.168.64.3

  Enable logging
  exploitation forest buffer-size 10000
  monitor debug logging
  logging buffered information
  asdm of logging of information

  outside_access_in list extended access allow all unreachable icmp
  outside_access_in list extended access permit icmp any any echo response
  outside_access_in list extended access permit icmp any one time exceed
  access extensive list ip 172.31.155.0 inside_access_in allow 255.255.255.0 any
  inside_access_in list extended access allow icmp 172.31.155.0 255.255.255.0 any
  Access extensive list ip 172.30.155.0 Corp_Voice_access_in allow 255.255.255.0 any
  Corp_Voice_access_in list extended access allow icmp 172.30.155.0 255.255.255.0 any

  VPN access list extended deny ip 172.31.155.0 255.255.255.0 object-group SunVoyager
  extended VPN ip 172.31.155.0 access list allow 255.255.255.0 any

  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Access-group Corp_Voice_access_in in the Corp_Voice interface

  Global 1 interface (outside)
  NAT (inside) 0-list of access VPN
  NAT (inside) 1 172.31.155.0 255.255.255.0

  Enable http server
  http 172.31.155.0 255.255.255.0 inside
  http 172.30.155.0 255.255.255.0 Corp_Voice
  http 192.168.64.0 255.255.255.0 Corp_Voice
  http 10.0.0.0 255.0.0.0 inside
  http 65.170.136.64 255.255.255.224 outside
  SSH 10.0.0.0 255.0.0.0 inside
  SSH 172.31.155.0 255.255.255.0 inside
  SSH 65.170.136.64 255.255.255.224 outside
  SSH timeout 20

  management-access inside

  dhcpd outside auto_config

  Crypto ipsec transform-set esp-3des esp-md5-hmac VPN
  crypto map outside_map 1 is the VPN address
  peer set card crypto outside_map 1 66.170.136.65
  card crypto outside_map 1 the value transform-set VPN
  outside_map interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  lifetime 28800

  tunnel-group 66.170.136.65 type ipsec-l2l
  IPSec-attributes tunnel-group 66.170.136.65
  pre-shared-key xxxxx

  output
  int eth 0/1
  close
  No tap
  int eth 0/2
  close
  No tap
  int eth 0/3
  close
  No tap
  int eth 0/4
  close
  No tap
  int eth 0/5
  close
  No tap
  int eth 0/6
  close
  No tap
  int eth 0/7
  close
  No tap

  Peter,

  Note that access list names are case-sensitive, so you've actually done something different from what I proposed.

  Please do:

  no nat (Corp_Voice) 0-list of access vpn

  No list of vpn access extended permitted ip TESTvpn 255.255.255.0 everything
  IP 172.30.155.0 255.255.255.0 extended vpn access do not allow any list all

  extended VPN ip 172.30.155.0 access list allow 255.255.255.0 any

  NAT (Corp_Voice) 0-list of access VPN

  In the case where you did deliberately, for example to separate the 2 acl: note that acl VPN (upper case) is also used in the encryption card, where you cannot add a second LCD.

  So if you want to separate you, you will need 3 access lists:

  list of access data-vpn ip TESTvpn 255.255.255.0 allow one

  voice-vpn ip 172.30.155.0 access list allow 255.255.255.0 any

  access-list all - vpn ip TESTvpn 255.255.255.0 allow one

  access-list all - vpn ip 172.30.155.0 allow 255.255.255.0 any

  NAT (inside) 0-list of access vpn data

  NAT (Corp_Voice) - access list 0 voice-vpn

  outside_map 1 match address all vpn crypto card

  Don't know if this was also clearly to my previous message, I recommend you to replace the "all" (in each of the ACL lines) to something more specific (i.e. a remote network, or group of objects that contain the remote networks).

  HTH

  Herbert

• Help the VLANS on Cisco SG200 - 08 p switch voice and data

  Hi all

  I'm faced with a problem of configuration on the Cisco SG200 - 08 p.

  We use Cisco SG200 - 08 p on a mobile carriage which will go from classroom to classroom who will have computer and phone VoIP cisco plugged into it. The question is that each of our closets are in different VLANS (1 voice and 1 data... Let's say data vlan 20 and vlan voice 2025 for conversation) and which move towards every closet.

  It would be great if I could just create a vlan voice dynamically pick up this switch upstream has however and generic data, it seems that I was failed to do.

  So far, I can pass the data Vlan no probably. The upstream switch port is set to access port and a switch port access voice vlan (these are x 3750 switches)

  If the above is not possible, I guess I'll take what I can get. Should I create data vlan 20 and vlan2025 of the voice on the Cisco SG200 - 08 p and make a port on the Cisco SG200 - 08 p and a trunk trunk on the 3750 x? Is there an option on the Cisco SG200 - 08 p to tag voice traffic?

  I am also concerned about DRIFTING and I did not see an area in the Cisco SG200 - 08 p to set it as a customer and a transparent mode.

  Thanks for any help,

  Dan

  Playne,

  first the bad news, the switches for small businesses currently do not support VTP, they support the GVRP Protocol which is like VTP, but there is no State that the VLAN used it will not automatically learn as VTP.

  You should be able to configure the 3750 as a trunk with a vlan 1U or unmarked and vlan 2025 as the tag for the voice. configuration of the port on the switch to small businesses the same way to its home port. All ports which have only phones will be 2025U of access and all ports only PC would be access 1U. All ports of phone and computer would be trunk 1u, 2025T

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• Smartphones blackBerry simultaneous voice and data on Verizon 3 G

  I got an iPhone 3G on AT & T and AT & T 3G network, I was able to use the data and voice simultaneously. This is supported on Verizon 3 G? I think not so much, but always wanted to know why this is the case.

  Fix. As it is now, correct.

• VLAN voice and data on a single port

  Hello

  I have some 5548 P Dell switches, but I just Cisco environment.

  I find a lot of information on this but most of it relevant to the VLAN marked and unmarked on a port in general. Some articles suggest to put the port in trunk mode...

  anyway (without taking into account the QoS) how you would accomplish this example Cisco on a Dell switch:

  Switch (config) #interface g0/1

  Switch(Config-if) #switchport mode access

  Switch(Config-if) #Switchport access vlan 50

  Switch(Config-if) #voice switchport vlan 10

  Thank you!

  For general mode, commands would be present as follows.

  Console (config) # interface gigabitethernet 0/1/1

  Console # switchport mode general

  Console # switchport general allowed vlan remove 10

  Console # switchport General allowed vlan add 2,3,4,50 tag

  Activate console # vlan VoIP

  Trunk mode:

  Console (config) # interface gigabitethernet 0/1/1

  Console # switchport mode Trunk

  Console # switchport Trunk allowed to remove vlan 10

  Console # switchport Trunk allowed vlan add 2,3,4,50

  Activate console # vlan VoIP

• SG500-52-K9-NA voice and data? s

  Just took a SG500-52 for the new addition of office and we just bought IP phones. I configured 1 port with vlan 41 voice given 100 shared resources and computer and telephone that work together. Even when I plug the computer directly into the switch, it still works even if the port is configured as a trunk and VLAN tagged 2? This work what's - what a smartport thing?

  Hi jbpollard,

  If you use a phone and a PC to a port, you must configure:
  -vlan 41 tagged
  -vlan 100 unidentified

  PC / laptop can mark normally not packages. This is why virtual LAN PC must not be tagged.
  The IP phone can mark packets.

  On the other Cisco switches, you can also set the client port as trunk. But then the vlan on the trunk native must be the vlan where the PC without going into.

• Turn off or disable the voice and data roaming notification over Vibe X 2

  Hi all

  -what someone has any idea how to turn off the question when you make a call outside your network home, as different country... its boring as hell and can't find the function. Phone is VIBE X 2 4.4.2

  Thank you

  Lollipop Android came out and fixed the "bug".

• to access the documents and data

  Hi all

  I still have problems of storage management on my phone, I get help here? I see the following numbers:

  Audio gb 7.05 which I suppose is including podcasts and voice memos.

  Photos of 9.2 mb.

  Apps for 1.59 GB.

  Documents and data 2.24 gb.

  Another 806,9 mb.

  How to handle the last two? What could possibly be taken 2.24 GB on my phone that I can't seem to?

  Documents and data includes the contents of applications. On the phone go to settings/general/storage & use iCloud and press manage storage under the rubric of storage. Lists the data used by each application on the phone.

• VDP (vCenter Data Protection) flow and data management.

  (1) is there any limit on the maximum FC and Ethernet through - was supported by the advanced version of POS?

  (2) maximum size of data capacity of 8 TB of VIENNA is combined of all 10 PDV (maximum supported by vCenter) devices, or for a single device?

  (3) if 8TB limit is for a single POS device, so is it possible to manage 80 TB (with 10 devices POS) per vCenter server.

  Thank you

  Sanjeev

  Is it mentioned in VMWare document that TB 80 and 80 simultaneous backup of VMs is the limit by vCenter?

  Thank you

  Sanjeev Shrivastava

• How can I use FNDLOAD for XML reports and data defnitions

  I program simultaneous registerd bound reports xml and data defnitions in instance of staging and managed to switch to DEV... After updating of this stage and when I download the details of DEV and transferred to the program only simultaneous scene I can download... Can we use the command FNDLOAD for definitions of data or the data model for the XML report, FNDLOAD used for the simultaneous program, he transferred only the details of the program at the same time.

  Hello

  Use XDOLoader.

  Note: 469585.1 - how to use XDOLoader?
  https://metalink2.Oracle.com/MetaLink/PLSQL/ml2_documents.showDocument?p_database_id=not&P_ID=469585.1

  Kind regards
  Hussein