at startup, I mesg.drive get 1 not found serial ATA, SATA2 and drive 3 not found parralell ATA, PAT-1 (PRI IDE SLAVE)

Similar Questions

• Looking for a NVIDIA nForce Serial ATA Controller Driver Update for HP Pavilion Elite e9140f

  Hi, I added a second hardrive that is 3 TB and my desktop is running windows 7 with SP 1.  I have been informed by Acronis technical support I need to get an NVIDIA nForce Serial ATA Controller update (I have version

  NVIDIA nForce Serial ATA Controller version 11.1.0.29 installed).  Can someone tell me what version I need update too and where to download?  Thank you!  Mark

  The last driver from Chipset from nVidia for your computer is located on the nForce Chipset Driver Version 15.56 download page. This driver install NVIDIA nForce Serial ATA Controller driver v11.1.0.43. This driver, however, isn't likely to solve your problem.

  You will need to check that the hard drive is seen in BIOS until the computer will recognize the drive. You will need to run the Windows 'Disk management' console to partition the hard drive in at least two partitions, MBR or GPT partition before you can use the drive.

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• On startup, I get the message following diskette drive 0 seek failure 1 not found drive Serial ATA, SATA 2 strike F-1 key to continue, F2 to run the utility series

  At the start of the black screen appears and tells Diskeyye drive 0 seek failure 1 drive not found: Serial ATA, SATA2 strike F1 key to continue, F2 to run the Setup utility, how can I keep this lift every time?

  Hi FRANKDURHAM,

  1. are you able to boot into Windows after the error message?

  2. did you of recent changes on the computer?

  3 when was the last time it was working fine?

  Usually, this would happen if the hard drive is not set correctly in the basic input/output system (BIOS) or the settings in the basic input/output system (BIOS) are incorrect.

  Basic input/output system (BIOS) is a program built into personal computers that starts the operating system when you turn on your computer. It is also referred to as system firmware. Basic input/output system (BIOS) is part of the hardware of your computer and is separate from Windows.

  Microsoft cannot provide specific instructions for changing your CMOS and BIOS settings because they are specific to your computer. For more information about the correct CMOS and BIOS settings for your computer and how to check and change these settings, see your computer documentation or contact the manufacturer of your computer.

  Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• I get a note telling me that my obsolete version of DLL Microsoft components is not compatible with this version of Windows. How to solve this problem?

  I recorded a CD on my C drive but I can't open it and I get the note above.

  Please tell us what to do and where I can get it as long as I can open the program?

  Hello

  1 are. what program you trying to install it using the files copied to the CD?

  2 did you change on your computer before the show?

  3. is the program you want to install compatible with Windows 7?

  Follow the steps mentioned below:

  Method 1:

  Check if the game software, program, is compatible with Windows 7

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Method 2: Start the computer in a clean boot, and then try to open the contents of your CD player clean boot

  A clean boot helps eliminate software conflicts. The article below describes how to solve problems in Windows 7 by performing a clean boot. This article also describes how to start the Windows Installer service and how to reset the computer so that it starts as usual. To configure your computer to clean boot see the following link.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: When you are finished troubleshooting, follow step 7 in the article to start on normal startup.

• Qosmio G35-AV600: using Recovery CD I get partition not created error

  I recently ordered a recovery for my Qosmio G35-AV600 disc, because I started in safe mode to clear an alleged threat. Silly me! I forgot the password because I constantly use the fingerprint reader. Well, at the time where, that drives recovery came, I had remembered a password and access I.

  The thing is I always want to format the laptop, but I get partition not created not errors. Is it because the laptop hard drive has SATA or RAID capabilities, or because of the so-called Qosmio player. * If I could format the hard drive, I would not be able to use the laptop Qosmio mode? *

  I searched here and even contacted the customer service and have not found a definitive answer. Customer support's solution was to send to an authorized repair shop. My experience with computer repair shops, is that if the problem is not hardware related, they simply reformat the disks. I could do it myself if I could get help with this "partition has not created" or the partition not deleted"errors.

  Hello

  I agree with you and I also think that this has nothing to do with the hardware failure.
  But who knows, if you started the operating system in safe mode then we shouldn't exclude the hardware problem (IE. HARD DRIVE).

  However, the restore CD contains already all the drivers and you n t need to install SATA or RAID drivers.

  In my opinion, there are bad RAID settings in the BIOS!
  Please check the settings in the BIOS on the third page.

  If you know n t that mean simple settings, you open the user manual and check RAID chapter in the user manual.

  In addition, this could be useful:
  http://support.toshiba-tro.de/KB0/TSB6901K60006R01.htm

• try to uninstall adobe 9.4.5 get access not granted no error

  y at - it an update for adobe reader

  When I try to uninstall adobe 9.4.5.i get access not granted error message what should I do I want to uninstall & reinstall it so that it works well

  Hello

  ·         What is the full error message?

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Follow the steps in the article.

  How to solve problems when you install or uninstall programs on a Windows computer

  Method 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  If the problem persists contact Adobe technical support for more help and information.

  http://www.Adobe.com/support/

  Reference: http://kb2.adobe.com/cps/498/cpsid_49880.html

• I can't open windows update in Safe Mode. Also blue screen at startup ('a forward driver a buffer based on the battery'

  My laptop keeps hitting a blue screen at startup ('a forward driver a buffer based on the stack'), I can only start it in safe mode. I want to try windows updates to see if this will help, but whenever I click on the button to update windows on the start menu, nothing happens. I tried searching for the program to see if I can open it another way, but can't find it. If I click on windows update and then nothing happened. I have windows vista home.

  original title: I can't open windows update

  Hey ElizabethSlater,

  Try to run a full scan with the Microsoft Safety Scanner to make sure that nothing is found.

  Try also to install the latest drivers from your computer manufacturer's website. If you have difficulty to locate the website of your computer manufacturer or the drivers on their page, please provide your computer brand and model in your next reply. If you have built your computer you need visit the site of the manufacturer of each piece of hardware to get the latest driver.

  Once the drivers have been installed, try to restart your computer, and then test to see if the same problem occurs.

  Hope that helps.

• drive 0 not found: serial ata, sata-0

  About 3 seconds to turn on my pc, I get the message:
  Drive 0 not found: Serial ATA, SATA-0
  Strike F1 key to continue, F2 to run the Setup utility.
  If I type F1, I get the message:
  No available boot device-
  Strike F1 to retry boot, F2 for Setup utility

  Please notify.
  Thank you.

  
  

• I'm having trouble installing my photoshop elements 14 since the website on my Mac book. I get the number of series, but when I click on download I get "Page not found".

  I'm having trouble installing my photoshop elements 14 since the website on my Mac book. I get the number of series, but when I click on download I get "Page not found"?

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

• Why do I get message not delivered on my SMS

  Why do I get message not delivered on my SMS

  Because they were not delivered for some reason any!

  Make sure that you connect to your cellular network (if you are using SMS), and that you have a data connection as well (if you use iMessage).

  In addition, call the intended recipient and ask that they check the same.

  You can also turn off and on your phone.

  Then test some messages.

• After installing the version 36.0 whenever I go to a Web site, I get "server not found" and I have to refresh

  After installing the version 36.0 (yesterday) on the desktop and laptop, whenever I go to a site that I get "server not found" and I update the site to access.

  I checked my firewall and it is configured correctly.

  And I changed the proxy for 'no proxy '.

  Still not fixed.

  Thanks in advance.
  David

  I went back to the 35.0.1 version and it seems to have solved the problem.

• Firefox crashes at startup for a single user, but not another

  Crash ID: bp-df3a48d7-363c-4d2f-87d3-f73902140723
  Version: 31
  Crashes at startup for a single user, but not another. Both are directors.
  I uninstalled and reinstalled. No change to each user.
  Crashes in safe mode as well (hold down the SHIFT key)
  No present addons in the other user.
  Ran Malwarebytes and cleaned
  Ran CCCleaner and clean up all registry including uninstalled Firefox entries.

  This is not useful if firefox crashes at startup. because you cannot start to create the new profile.

• modules of tools/add-on/get = do not load or extensions are not displayed

  Cannot manage add-ons as window modules Get [under Tools/Add-ons custom] shows to load but never completes the operation [load] or give any message. How can I get this feature work?

  If you want modules eats then you can click on one of the other tabs as Extensions or Plugins.
  
  It can occur more frequently the modules tabs get does not respond or takes a long time.

  If the Extensions tab does not always display the Extension then it is possible that there is a problem with the files that store the registry extensions.

  Delete the files (extensions.sqlite, extensions.ini) extensions.* and compatibility.ini in the profile folder of Firefox to reset the extensions registry.

  • https://support.Mozilla.org/KB/profiles

  New files will be created if necessary.

  See "extension corrupted files:

  • http://KB.mozillazine.org/Unable_to_install_themes_or_extensions
  • https://support.Mozilla.org/KB/unable+to+install+add-ons

  If you see people with disabilities, is not compatible extensions in "tools > Modules > Extensions ' and then click the Tools button, on the side of the left end of the search bar ('Find updates' button in older versions of Firefox) to check if there is an update available compatibility.

  If this did not help, then also delete the addons.sqlite file.

• I tried everything, but I get "SERVER NOT FOUND TRY AGAIN" when I try again his connects. What is the prayer of the problem. N ".

  I tried everything but keep getting "SERVER NOT FOUND TRY AGAIN" when I try again once it normally connects. What is the problem please

  This can have several reasons:

  first make sure that your firewall/security software allows firefox to fully access the internet.

  then you can try the solutions (proxy settings, the change of dns server) provided in this support thread: https://support.mozilla.org/de/questi.../704934

  If this does not help, also try disabling ipv6 as described here: https://support.mozilla.org/en-US/kb/Server%20not%20found?s=server%20not%...

• In iPhoto, when I hit the info icon, I get a note of gobbledygook.

  In iPhoto, when I hit the "info" icon, I get a note long gibberish.  The button 'edit', 'create', ' add to ' and 'share' icons work OK.

  What version of iPhoto? Is OS X 10.5.8 as you say correct for your OS? Post a screen shot of your 'gibberish' - take the screenshot and click on the camera icon in the top bar of the composition to include window off screen

  LN