At the beginning and end of the audio Volume control

Similar Questions

• 39L4363D - cannot set the record time of beginning and end of filling time

  Hello

  I have a problem with my 39L4363DG tv (software 7.1.90.34.01.1).

  I'm not able time of filling time of beginning and end of record setting as described in the [Manual | http://www.toshiba-om.net/LCD/PDF/English/L4363-323950-English.pdf] on page 51. The menu item "padding-start" and 'end padding time' are disabled?

  Can someone help me and give me advice on how to solve it?

  Hello

  The charging time can be set for the scheduled recording.

  There is also a priority planning
  If the regular time intervals are ensuites to each other and there is more than one minute between the time of the end of the annex i and the next scheduled start time, scheduled recording will be performed correctly.

  When + start time of filling + and + hour of end padding + are value, the start time and end time more is the time the extra minutes.

  If planning time overlap, priority will be given to the scheduled recording starts first.
  When the scheduled recording that began the first ends, recording will switch to the next regular program.
  At that time, according to how much programming time to overlap, the section from the beginning of the next regular program is not registered.

• Points of beginning and end of a song seems to change at random in the Bounce dialog box

  Even if I put the departure and arrival within the project, when am I going to bounce the project the bounce dialog box displays the numbers of different from what I've specified. Everyone sees what is happening? Using X 10.2.1 Pro logic.

  The start and endpoints of a rebound are determined by:

  1 cycle. If a cycle is active when you give the command Bounce , then the start and endpoints of the cycle to determine the length of rebound.

  2 selection. If no cycle is active, but there are one or more area (s) selected, the early rebound and the end will be the selections start and endpoints.

  3. If no region is selected and the cycle is not active, then the beginning and end of the project are defined as the bouncing range.

  http://help.Apple.com/LogicPro/Mac/10.2/#/lgcp190ba9b7

• Noise at the beginning and end of the songs?

  I get a humming sound for a split second at the beginning and end of the songs which can be heard at high volume.  The sound only comes from the left atrium.  I tried a few different pairs of headphones and get the same result, then it is definitely the Clip.

  It of just a feature of the Sansa Clip or is there something wrong with my drive?

  TIA

  I tried ripping the mp3 with two different programs, and it does not solve the problem.  Mind you, these are the same files of music that I had installed on my iPod Shuffle 2nd without noise.

  Today I bought another Sansa Clip and it does the same thing only for the straight path instead of the left.

  My conclusion is that it is an inherent problem with the Sansa Clip.  The reason why some of you can't hear this 'noise', I'm talking about is because I have the ears of a bat.

• Breaking a year in coming weeks of beginning and end Dates (parameters) and first and last day of the month

  Hello people:

  I have currently a query that picks up all the weeks between a date range where my week starts on Thursday and ends on Wednesday. The following query works fine except that I need the week of beginning and end, from beginning and end Dates of months and the beginning and the Dates of end of the values of the settings, I'm passing. In this case, I chose January 1, 2013 to 31 December 2013.

  Any help or pointers would be great!

  Thank you!

  Problem: I am picking up days of December 2012 as the first week began on December 27, 2012. In addition, in December, I'm pretty much lost last week as well (26 December - 31 December).

  The request in hand:

  SELECT first_thursday + (7 * (LEVEL - 1))   AS week_start_date,
                   first_thursday + (7 * LEVEL) - 1    AS  week_end_date
  FROM
  (
    SELECT TRUNC(p_from_date + 4, 'IW') - 4   AS first_thursday, -- Week should start the pre ceeding THURSDAY based on the Start Date
                    TRUNC( p_to_date + 4,  'IW') - 5     AS last_wednesday
    FROM
    (
      SELECT to_date('01-JAN-2013') AS p_from_date,
                      NVL(to_date('31-DEC-2013'), SYSDATE) AS p_to_date
      FROM     dual
    ) parms
  ) end_points
  CONNECT BY LEVEL <= ( last_wednesday + 1 - first_thursday)/7;
  

  Currently, this is the result I get (I'm only including the months of January and December here).

  Week_Start_Date     Week_End_Date
  27-DEC-12                02-JAN-13
  03-JAN-13                 09-JAN-13
  10-JAN-13                 16-JAN-13
  17-JAN-13                 23-JAN-13
  24-JAN-13                 30-JAN-13
  31-JAN-13                 06-FEB-13
  

  December:

  28-NOV-13               04-DEC-13
  05-DEC-13              11-DEC-13
  12-DEC-13              18-DEC-13
  19-DEC-13              25-DEC-13
  

  What I would really like is based on start and end Dates, as well as the first and the last day of the month is similarly try nicely. I have provided and then gently break at the end of the month:

  January:

  01-JAN-13              02-JAN-13
  03-JAN-13              09-JAN-13
  10-JAN-13             16-JAN-13
  17-JAN-13             23-JAN-13
  24-JAN-13             30-JAN-13
  31-JAN-13             31-JAN-13
  

  February:

  01-FEB-13    06-FEB-13
  07-FEB-13    13-FEB-13
  14-FEB-13    20-FEB-13
  21-FEB-13    27-FEB-13
  28-FEB-13    28-FEB-13
  

  November:

  31-OCT-13    06-NOV-13
  07-NOV-13    13-NOV-13
  14-NOV-13    20-NOV-13
  21-NOV-13    27-NOV-13
  28-NOV-13    04-DEC-13
  

  December:

  01-DEC-13           04-DEC-13
  05-DEC-13           11-DEC-13
  12-DEC-13          18-DEC-13
  19-DEC-13          25-DEC-13
  26-DEC-13          31-DEC-13
  

  Hello

  Roxyrollers wrote:

  Hello people:

  I have currently a query that picks up all the weeks between a date range where my week starts on Thursday and ends on Wednesday. The following query works fine except that I need the week of beginning and end, from beginning and end Dates of months and the beginning and the Dates of end of the values of the settings, I'm passing. In this case, I chose January 1, 2013 to 31 December 2013.

  Any help or pointers would be great!

  Thank you!

  Problem: I am picking up days of December 2012 as the first week began on December 27, 2012. In addition, in December, I'm pretty much lost last week as well (26 December - 31 December).

  The request in hand:

  1. First_thursday SELECT + (7 * (LEVEL - 1)) AS week_start_date,
  2. first_thursday + (7 * LEVEL)-1 AS week_end_date
  3. Of
  4. (
  5. SELECT TRUNC (p_from_date + 4, 'IW') - 4 AS first_thursday,-week should start to perform the pre-mounted THURSDAY based on the Start Date
  6. TRUNC (p_to_date + 4, 'IW') - 5 AS last_wednesday
  7. Of
  8. (
  9. SELECT to_date('01-JAN-2013') AS p_from_date,
  10. NVL (to_date('31-Dec-2013'), SYSDATE) AS p_to_date
  11. OF the double
  12. ) parms
  13. ) end_points
  14. CONNECT BY LEVEL<= (="" last_wednesday="" +="" 1="" -="">

  Currently, this is the result I get (I'm only including the months of January and December here).

  1. Week_Start_Date Week_End_Date
  2. DECEMBER 27, 12 2 JANUARY 13
  3. JANUARY 3, 13 JANUARY 9, 13
  4. 10 JANUARY 13 JANUARY 16, 13
  5. 17 JANUARY 13 23 JANUARY 13
  6. 24 JANUARY 13 30 JANUARY 13
  7. 31 JANUARY 13 FEBRUARY 6, 13

  December:

  1. NOVEMBER 28, 13 4 DECEMBER 13
  2. 5 DECEMBER 13 DECEMBER 11, 13
  3. 12 DECEMBER 13 18 DECEMBER 13
  4. 19 DECEMBER 13 DECEMBER 25, 13

  What I would really like is based on start and end Dates, as well as the first and the last day of the month is similarly try nicely. I have provided and then gently break at the end of the month:

  January:

  1. JANUARY 1, 13 2 JANUARY 13
  2. JANUARY 3, 13 JANUARY 9, 13
  3. 10 JANUARY 13 JANUARY 16, 13
  4. 17 JANUARY 13 23 JANUARY 13
  5. 24 JANUARY 13 30 JANUARY 13
  6. 31 JANUARY 13 JANUARY 31, 13

  February:

  1. 1ST FEBRUARY 13 FEBRUARY 6, 13
  2. 7 FEBRUARY 13 FEBRUARY 13, 13
  3. 14 FEBRUARY 13 FEBRUARY 20, 13
  4. 21 FEBRUARY 13 FEBRUARY 27, 13
  5. 28 FEBRUARY 13 FEBRUARY 28, 13

  November:

  1. 31 OCTOBER 13 NOVEMBER 6, 13
  2. 7 NOVEMBER 13 NOVEMBER 13, 13
  3. 14 NOVEMBER 13 NOVEMBER 20, 13
  4. 21 NOVEMBER 13 NOVEMBER 27, 13
  5. NOVEMBER 28, 13 4 DECEMBER 13

  December:

  1. 1ST DECEMBER 13 DECEMBER 4, 13
  2. 5 DECEMBER 13 DECEMBER 11, 13
  3. 12 DECEMBER 13 18 DECEMBER 13
  4. 19 DECEMBER 13 DECEMBER 25, 13
  5. 26 DECEMBER 13 DECEMBER 31, 13

  Why the "weeks" in November, have all 7 days, while the "weeks" in the first or the last week in the other month usually have less?  (For example, February 28 is a 'week' alone.)

  The following works for the other months:

  WITH all_days AS

  (

  SELECT DATE "2013-01-01' + LEVEL - AS a_date 1

  OF the double

  CONNECT BY LEVEL<=>

  )

  SELECT DISTINCT

  More GRAND (TRUNC (a_date + 4, 'IW') - 4)

  , TRUNC (a_date, 'MONTH')

  ) AS week_begin

  , The LEAST (TRUNC (a_date + 4, 'IW') + 2

  TRUNC (LAST_DAY (a_date))

  ), Week_end

  Of all_days

  ORDER BY week_begin

  ;

  Output:

  WEEK_BEGIN WEEK_END

  ----------- -----------

  January 1, 2013 January 2, 2013

  January 3, 2013 January 9, 2013

  January 10, 2013 January 16, 2013

  January 17, 2013 January 23, 2013

  January 24, 2013 January 30, 2013

  January 31, 2013 January 31, 2013

  February 1, 2013 February 6, 2013

  February 7, 2013 February 13, 2013

  February 14, 2013 February 20, 2013

  February 21, 2013 February 27, 2013

  February 28, 2013 February 28, 2013

  ...

  November 1, 2013 November 6, 2013

  November 7, 2013 November 13, 2013

  November 14, 2013 November 20, 2013

  November 21, 2013 November 27, 2013

  November 28, 2013 November 30, 2013

  December 1, 2013 December 4, 2013

  December 5, 2013 December 11, 2013

  December 12, 2013 December 18, 2013

  December 19, 2013 December 25, 2013

  26 December 2013 31 December 2013

• Beginning and end of the week according to YYYYWW

  Hi all
  
  I have a date like format
  
  201050
  201051
  201052
  201101
  
  I wanted to display their dates of beginning and end of the relevant year - week.

  SQL> with t as (
    2   select 201050 yw from dual union all
    3   select 201051 from dual union all
    4   select 201052 from dual union all
    5   select 201101 from dual union all
    6   select 201102 from dual
    7  )
    8  --
    9  --
   10  select yw, trunc (trunc (to_date (substr (yw, 1, 4), 'yyyy') + 7, 'iyyy') + 7 * (substr (yw, 5) - 1), 'iw') start_dt
   11    from t
   12  /
  
               YW START_DT
  --------------- -----------
           201050 13/dec/2010
           201051 20/dec/2010
           201052 27/dec/2010
           201101 03/jan/2011
           201102 10/jan/2011
  
  5 rows selected.
  
  SQL>
  

• How do I add or remove silence at the beging and end of each audio file by using batch

  Hi all

  I'm new to this forum. I've been using Audition 3 for the last two years and these days I need to coop with a very difficult situation, which is; I have over 2000 files that begin and end with a random length of silence, it varies from 0 to 7 sec. My question is, how do I set the duration of silence at the beginning and at the end of each file to a constant quantity of 2s using batch?

  Kind regards

  Pavlos

  pavlos22 wrote:

  My question is, how do I set the duration of silence at the beginning and at the end of each file to a constant quantity of 2s using batch?

  You have to perform two processes to achieve this. The first is that you need to remove all amounts of the silence of the files, so that they begin at zero and stop at the end. You can do it automatically using edit > delete Silence, but you should pay attention to how implement you.

  After that, you need a script to add a set amount of silence at each end of each file and run this as a batch process. Information on how to do that are in this thread, in the role of fourth, and as far as I know, this is the only way to do it. There is more information in the rest of the wire also, explain how it actually works.

• Mobsync.exe begins and ends several times when running directX games

  Whenever I start a current game directx mobsync.exe enforcement begins and ends. It causes a shift in the game and the cheek than the "dee-dum' sound as if I am connect and disconnect a USB device. I changed everything in the system for material. New motherboard, new RAM, different video card, changed to keyboards and mice, disconnect all USB devices and the problem still persists. Mobsync.exe will begin or wmplayer will start then end immediately and that this repeatedly until the game is closed. does anyone have any idea what this might be? Help, please! It's very frustrating.

  Intel Core 2Duo

  ATI Radeon HD3650 PCIE16

  4 GB OF DDR3 MEMORY

  Finally I thought of her. The problem was with a compatibility problem with a USB display controlled on a case of SilverStone Media Center. I found this through the process of elimination. After unplugging the screen before the problem disappeared.

• begin and end in awr report

  Hi all

  Hope all are well. I need your help, I doubt reading the awr report.

  Summary of the report

  Cache sizes

  	Start	End
  Cache buffers:	572 M	572 M	Std block size:	8K
  Size of the shared pool:	408 M	408 M	Log buffer:	13 604 K

  My question is what is 'START' and 'END' in the figure above and why to cache buffer and shared pool sizes are the same for BEGIN and END.your help appreciated, thanks in advance.

  Best regards.

  size of the buffer at the start of the snapshot cache

  size of the buffer at the end of the snapshot cache

  Shared at the beginning of the snapshot pool

  Shared pool, at the end of the snapshot

  So that means: either you did not Oracle or Oracle to change these settings dynamically does not need to change.

  Always send four-digit version of your database and platform info. This forum is not keeping track of it.

  ---------------

  Sybrand Bakker

  Senior Oracle DBA

• Beginning and end of check date

  Hello
  
  I have a requirement to find a list of people that have dates that overlap.
  
  Each person can have several Dates of beginning and end, but only one line that has a null term, the current record. If the start and end dates are overlapping, as in the example below, the second row should have a start date of December 24, 2006 and 22 December 2006. Is it possible to list people who have dates and gaps that overlap in the dates.
  
  Empl_ID Start End Date
  12345 1 JANUARY 2006 DECEMBER 23, 2006
  12345, DECEMBER 22, 2006 13 JANUARY 2007
  12345 NULL JANUARY 14, 2007
  
  Any help is greatly appreciated.
  Thank you!

  Hi Patrick
  I like where you're coming. I hope you don't mind but I have extended your idea slightly to add in a PARTITION BY clause to make sure that we look at the records for the same person. Also, if we LAG for a previous record shouldn't we us DRAGS the end_date and compare it with the current start_date?

  LAG(END_DATE,1) OVER (ORDER BY START_DATE EMPL_ID PARTITION)

  In doing so, then the results would look like this:

  Empl_ID Start Date End Date Lag
  12345 1 JANUARY 2006 23 DECEMBER 2006 NULL
  12345 22 DECEMBER 2006 JANUARY 13, 2007 DECEMBER 23, 2006
  12345, 14 JANUARY 2007 NULL JANUARY 13, 2007

  This would give the SIGN a problem because in the first record, the OFFSET would be NULL and the last record the end_date would be NULL. So, it seems that some handling of NULL values must be as well which I will deal with later.

  SIGN ((LAG(END_DATE,1) OVER (ORDER BY START_DATE EMPL_ID PARTITION))-START_DATE)

  At all times the difference between the Start Date and the Date of Lag is positive, this means, that there is an overlap which means that we must look for any gap where the SIGN is 1.

  Using the other function, we could use the LEAD like this:

  LEAD(START_DATE,1) OVER (ORDER BY START_DATE EMPL_ID PARTITION)

  In doing so, then the results would look like this:

  Empl_ID Start Date End Date lead
  12345 1 JANUARY 2006 DECEMBER 23, 2006 DECEMBER 22, 2006
  12345 22 DECEMBER 2006 JANUARY 13, 2007 JANUARY 14, 2007
  12345 NULL NULL 14 JANUARY 2007

  When combined with the SIGN becomes: SIGN ((LEAD(START_DATE,1) OVER (PARTITION OF EMPL_ID ORDER start_date)) - end_date)

  This time you would look at the sign at-1

  Personally, I think that I would prefer the LEAD function because one) there will always be a start_date and b) we could replace all possible NULL values with the SYSDATE to get a final calculation like this:

  SIGN (NVL (LEAD(START_DATE,1) OVER (PARTITION BY ORDER OF START_DATE EMPL_ID), TRUNC (SYSDATE))-NVL (END_DATE, TRUNC (SYSDATE)))

  Based on the date is November 17, 2009, you would now get this result:

  Empl_ID Start Date End Date lead
  12345 1 JANUARY 2006 DECEMBER 23, 2006 DECEMBER 22, 2006
  12345 22 DECEMBER 2006 JANUARY 13, 2007 JANUARY 14, 2007
  12345 JANUARY 14, 2007 NOVEMBER 17, 2009 NOVEMBER 17, 2009

  Best wishes
  Michael

• How to increase the control limits for the Audio Volume?

  I have upgraded my PC base unit and no longer have the output of the Speaker Volume I had before. The audio output is more silent than before with the same speakers I used. I have moved all the sliders on the control panel of the Volume on their maximum position, but still can't get enough of output to the speakers. The important thing is for my use are 'Volume Control' and 'Wave', and these are set to the maximum. Now I have a motherboard with Intel D845GERG2 Intel i845GE chipset. The operating system is Windows XP Professional SP3, as previously. The sound card is SoundMAX Integrated Digital Audio with Legacy audio drivers. I checked using Device Manager drivers and hardware to work properly. The problem is software because I can achieve the required high speaker volume if I use VLC Media Player and set the volume to 200%. With Windows Media Player, set the volume to 100% is sufficient. I'm looking to increase range parameter on the control panel of Volume as a general solution. Can you advise if this is possible? I looked at a few ideas, these courses: edit files (.inf) SoundMAX driver. Modify the registry keys concerned. Use different audio drivers (none seem to be available for my hardware). Install the software to boost the audio output (VLC Media Player should be achieve this somehow). Install alternative (rollback) Microsoft drivers. Any advice would be much appreciated.

  Just an update of my efforts on this issue.

  I revisited the audio registry settings SoundMAX for HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ \0005\Settings {4D36E96C-E325-11CE-BFC1-08002BE10318}. These are installed when you install the driver for SoundMAX Integrated Digital Audio. Changing these settings has already failed to get an increase of output audio volume. I have now found some settings of the value of these registry keys that have given me a satisfactory increase in the volume of the audio. In short, the cure for my situation was:

  The file source (wdm3516b_Cadenza.exe) driver available from the Download Center Intel is a self-extracting ZIP file. Unzip this file to a location convenient temporary store (C:\Temp)

  Use a text editor (Notepad) to edit the INF of the driver - in my case, it's "smwdmCH4.inf. Changes to this file cause the digital signature of the file to be invalid, but choose "Continue Anyway" to solve this problem during the installation of the driver. To increase the sound volume levels, the audio volume registry key value parameters that have been predefined 08 (hex) have been changed to 01 (hex). I suppose that this change dB levels produced by the SoundMAX Integrated Digital Audio.

  To install the new settings:

  Uninstall the SoundMAX Integrated Digital Audio hardware by using Device Manager.

  Restart the PC - this should give a "new hardware found" restart of the PC.

  Use Device Manager to reinstall the driver for SoundMAX Integrated Digital Audio. Do not use the automatic selections for this - run the installation process where you stored the INF driver edited file.

  Once installation is complete, a check on the properties of the device must indicate that the device is functioning properly.

  Use regedit to check that changes in the edited file driver INF appeared in the area of the Windows registry - in my case, it is HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ {4D36E96C-E325-11CE-BFC1-08002BE10318} \0005\Settings.

  I will emphasize that it is NOT a recommended fix - it turns out that it worked for me. The usual caveats apply - save your original settings, or better yet, use software disk image to make a copy of your drive hard so that you go back to square one if she's going "pear-shaped" with adaptations that have been made.

• Could not set the audio volume on BlackBerry Pearl 8130

  Hello

  All first of all information about the device and the JDE:

  Device: BlackBerry Pearl 8130 (Bell)

  F/w: 4.3.0.66 (Platform 3.1.0.35)

  JDE: 4.3.0.1r

  Our application reacts on the main events of entry of the volume keys and set the audio volume accordingly in increments of 10. While net.rim.device.api.system.Audio.getVolume () works very well and returns the correct value, we are unable to adjust the volume. Adjustment is made through net.rim.device.api.system.Audio setVolume(int volume). Calling the method seems to succeed because there is no error returned. If we call setVolume (90) after that getVolume() return 100 the next call of getVolume() returns 90. However there is no noticeable change in volume. Even though getVolume() returns 0 audio is always heard.

  Play media files is via MMAPI, i.e. javax.microedition.media.Manager and javax.microedition.media.Player.

  Please note that the volume control works very well for BB Pearl 8100 with firmware version v4.2.1.101 (Platform 2.3.0.80) but fails for the above device. Application is signed.

  How is it possible to adjust the audio volume of BB Pearl 8130?

  CDMA devices (xx30) do not properly set the volume if you use the setVolume(int i) function.

  net.rim.device.api.system.Alert.setVolume (int x) is also available.

  Maybe it works!

• Y at - it controls fade or volume for the audio volume?

  Y at - it controls fade or volume for the audio volume? For example, if you want to use an audio clip and adjust the volume.

  Cabbagepatchkid

  First Elements 12 Mac

  You should be able to click with the right button on your audio files and select fade, followed by fade in Audio or Fade Out Audio.

  Please check out my blog on bland

  First Elements ATR troubleshooting: PE11: Timeline Fade Out shortcuts and stretched / remappe time video

  As mentioned I'm strictly a Windows elements user, so I guess that the first elements of Windows and Mac

  are the same on this feature.

  Please let us know if you need any clarification on the above.

  Thank you.

  RTA

• change the properties of the report axis (together begin and end)

  Hey everybody,

  I am a beginner with DIAdem reports and close to despair that I have yet found any solution.

  I wrote a script, which produces reports of various measures with 9 pages (3 2D-slots each, a total of 27 lots).

  Now, I want to put the beginning and the end of the x-axis of certain specific parcels.

  First question: tiara offers something similar to an Object Explorer (for easy access to the names of the objects drawn in a report)?

  I created two GlobalDims called x_time_begin and x_time_end to set these properties, but I don't know how to access these variables in the report (tried @... @ and @... @ the 'Axis settings' tab).

  These variables change for each measure, so each report has a different set.

  The presentation of the State is responsible from a set of. TDMS files and is not altered in the script.

  How can I find the name of a specific plot in the report can access?

  Is it possible to define the range of the x-axis in a variable at all?

  Best regards

  Nils

  Hi Nils,

  It is possible to set the x-axis of begging and positions in the scripts end (see text below).  When you create a report object in the script you can name it anything you want to access later. Otherwise, I think that the default name is the name of the object, of the number (for example the 2D first table is called "2DTable1")

  Dim oMy2DAxisSystem, oMyXScaling
  
  Report.NewLayout
  
  Set oMy2DAxisSystem = Report.ActiveSheet.Objects.Add (eReportObject2DAxisSystem, "My2DAxisSystem")
  
  Set oMyXScaling = oMy2DAxisSystem.XAxis.Scaling
  
  oMyXScaling.AutoScalingType = eAxisAutoScalingManual
  
  oMyXScaling.Begin = 0.01
  
  oMyXScaling.End = 100

  Hope that helps,

  Sadie

• Hide using the date of beginning and end of line

  Is there a way to hide using the start date and end date of line

  

  One way to do is to add a filter column (which may hide once it is configured) like this:

  

  The formula in D2, filled to the bottom, is:

  = AND(A2≥$B$8,A2≤$B$9)

  The filter (on column D) looks like this in the right panel:

  

  C9 formula is:

  = SUMIFS(C,A,">="&B8,A,"<="&B9)

  After changing the end date of 2014-12-31, you get this:

  

  I left column displayed D just for illustration.

  SG