audio and video not synchronized. returned to projects already finished and they also are not synchronized. What could be the problem?

Similar Questions

• IBM Thinkpad R52 beep but will not charge what could be the problem?

  The machine will beep 3 times then 1 hour then 4 and finally 3 times.  does not load windows xp

  Hello

  The feedback Forum is for feedback on the Forums for answers.

  You should ask in the answers – Windows Forums for your version of Windows.

  Answers - Windows Forums
  http://answers.Microsoft.com/en-us/Windows

  =====================

  Sound beeps are error codes that describe a problem with your machine.

  Startup and select CONFIGURATION/SETTINGS (BIOS/CMOS) - usually F2 that you start - look to see BIOS
  Creator, then see here:

  Computer MESSAGE / beep codes
  http://www.computerhope.com/beep.htm

  If my computer beeps and won't start, what do the beeps mean?
  http://KB.IU.edu/data/afzy.html how to troubleshoot Beep Codes
  http://pcsupport.about.com/od/nonworkingcomponent/HT/beepcodestb.htm

  POSTAL Codes beep
  http://www.technick.NET/public/code/cp_dpage.php?aiocp_dp=guide_beep_codes

  Power on Beep Codes post
  http://www.pchell.com/hardware/beepcodes.shtml

  It can be so other check with the manufacturer of the system.

  I hope this helps.

• I have a desktop with Windows Vista. Many times, the screen is the gel with an error massage "video Mode not supported". What could be the problem and the solution. ?

  I have a desktop with Windows Vista. Many times, the screen is the gel with an error massage "video Mode not supported". What could be the problem and the solution. ?

  Hi Izzy Nagar,

  ·         Exactly when you receive this error message?

  ·         Did you do changes on the computer before the show?

  ·         Do you have any extended monitor connected to the computer in the past or at the present time?

  Follow the suggestions below for a possible solution:

  Method 1: You can try to reduce the resolution of the screen (lower), then check if the message still appears.

  Check also if the refresh rate of the monitor is set correctly and check the manual of the monitor for assistance.

  Ways to improve display quality

  http://Windows.Microsoft.com/en-us/Windows-Vista/ways-to-improve-display-quality

   

  Flicker of the correct monitor (refresh rate)

  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  Method 2: Use the option ' enable video low resolution (640 × 480) "start, then update your video card driver and check if the problem still persists.

  a. click the Start button, click the arrow next to Shut Down and then click on restart.

  b. do one of the following:

  ·         If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  ·         If your computer has more than one operating system, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  c. on the Advanced Boot Options screen, use the arrow keys to select activate video low resolution (640 × 480) and press ENTER.

  d. connect to your computer with an account of a user who has administrator rights.

  e. If you can see your desktop, there is a problem with your video card. Try to update your video card driver. For more information, see the article:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

   

  I hope this helps.

• Hello, I paid my monthly subscription to Adobe cc but its not not opening my project, what could be the problem? Thank you.

  I paid my monthly subscription to Adobe cc but its not not opening my project, what could be the problem? Thank you.

  Using creative cloud | Applications creative Cloud back to update evaluation Mode to 2015 CC

  Creative Cloud applications unexpectedly back in the test mode. CCM, CS6

  I hope this helps.

  Concerning

  Megha Rawat

• Unable to set keyframes in the audio clip selected with the pen tool - can no longer see the volume control line after developing the clip. What could be the problem? This seems to be the problem on any project that I opened.

  Cannot set keyframes in the audio clip selected with the pen tool - cannot see even the line volume control more to set keyframes on having developed the clip. What could be the problem?  I use the first CC pro @.

  You can use the Ctrl key and then click with the regular selection tool, clicking with ctrl will make a new keyframe. in this way, have no need for the tools. CTRL has other great shortcuts that will stop you having to spend retouching pads tools too.

  If the automation keyframe line is missing, you can switch on and off in the menu sequence.

  

• Version 6.1 of Windows Movie Maker in Windows vista does not burn my dvd. We know what could be the problem?

  Any suggestions at this point? Help, please! Need HELP PLEASE, Please HELP I tried to do a restore point - but will not let me go back in May of this year because from there all cleaned up disk cleanup. Whenever I stop using Windows Movie Maker for a few months, something always goes wrong.
  It worked perfectly in May of this year.
  Always updated wondows movie maker 2.6 mess all completely is why I stick to the old version.  I tried to restore the values by default in compatibility - does not seem to make a diff. We know what could be the problem?  It starts to burn my movies that I've done and about a quarter of the way in which it stops and a pop up lights and that States "cannot create the dvd, unspecified error."

  Any suggestions at this point? Help, please! Need HELP PLEASE, Please HELP I tried to do a restore point - but will not let me go back in May of this year because from there all cleaned up disk cleanup. Whenever I stop using Windows Movie Maker for a few months, something always goes wrong.
  It worked perfectly in May of this year.
  Always updated wondows movie maker 2.6 mess all completely is why I stick to the old version.  I tried to restore the values by default in compatibility - does not seem to make a diff. We know what could be the problem?  It starts to burn my movies that I've done and about a quarter of the way in which it stops and a pop up lights and that States "cannot create the dvd, unspecified error."

  ==========================================
  FWIW... Windows Movie Maker 2.6 is not an update... it's a disassembled
  version for systems that will not run Vista Movie Maker 6.

  The new version... would be Windows Live Movie Maker. It is quite
  different from version 6. If you decide to try it... plan on creating
  a new project because your version 6 files probably will not
  be compatible.

  Windows Live Movie Maker
  http://explore.live.com/Windows-Live-Movie-Maker
  (There are other applications included in the download...
  Uncheck the ones you don't want)

  As for the error... I wonder if you may have a compatibility issue
  with your source files.

  Several formats are apparently compatible with Movie Maker but the
  more reliable choices are:

  Photos - bmp
  Video - wmv or dv - avi
  Music - wma, wav, wmv

  Have you tried editing (save) your project in the WMV movie
  format and then importing the video file in Windows DVD WMV
  Maker?

  It is also possible that your project is too large or complex.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• After that I closed the lid on my laptop, when I reopen it, I have to keep moving the lid until I can get a picture. What could be the problem and how to fix?

  After that I closed the lid on my laptop, when I reopen it, I have to keep moving the lid until I can get a picture.  What could be the problem and how to fix?

  Hello

  Looks like a loose connector or a short circuit in the video cable. Check with a real
  store computer (one that works on computers cell phones internal ASUStek) or ASUStek
  Support, their documentation and online in their forums.

  Not a maintainable question by the user.

  ASUStek support
  http://support.ASUS.com/

  ASUStek Forums
  http://VIP.ASUS.com/forum/default.aspx?SLanguage=en-us

  ASUStek drivers
  http://support.ASUS.com/download/download.aspx?SLanguage=en-us

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• my lap top last 10 minutes and just shuts down what could be the problem

  my lap top powers on and works fine for about ten minutes is so stop just to what could be the problem

  Hello

  Could be heat related - try using a small fan to blow into the air intakes to see if that helps.
  It is just like it loses power or stop it in the normal way? Keep in mind
  This associated heat does not always mean too much heat as it is often a part or a component
  who is too sensitive to normal levels even heat.

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Remove the dust bunnies and clean the
  air vents. Check that fans are working (before and after opening the case). When your laptop on all the
  You can do is to reinstall the memory and clean the vents (still may try to add a small fan as a
  test).

  This sounds like material so if the above does not help you then probably need help
  a real computer store (not the leeks and the glances at a Best Buy or other stores) or the
  Support of system Maker.

  ======================================================

  Pick up the pieces after a computer crash
  http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash

  Check this thread for more information on using BlueScreenView, MyEventViewer and other
  Troubleshooting BlueScreens - top 3 responses (+ 1 other) methods.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/blue-screen-plug-and-play-detected-an-error-most/3deab2fa-4000-4136-8c78-a3d22b1db009

  ---------------

  Check with these utilities to see if information may be collected: run BlueScreenView
  to see if there were any BlueScreens and verify in MyEventViewer at shutdown
  (or a few seconds before) See the event log contains useful information.

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) or event within a second
  or time of the BSOD or event to provide more information about the possible cause - see TIP.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it a bit before and after the time of the event or BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 which shows details
  application of all accidents occurred in your system. The information breaks down is extracted from the
  .WER files created by the Windows Error Reporting (WER) of the operating system component of each
  time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
  text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  ------------------------------

  Also do this so you can see the probable bluescreens. (You may or may not be able to see
  them if they occur even after doing this according to the cause.)

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  (also Windows 7)
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I try to install yahoo mesengerand it keeps giving me a pop-up Microsoft Windows.The error is the following: could not initialize properly (0xc0150002). What could be the problem?

  I try to install Yahoo Mesenger and it keeps giving me a pop-up Microsoft Windows.The error is the following: could not initialize properly (0xc0150002). What could be the problem?

  Hello DennisUSMC,

  Look at the thread in Yahoo Answers.
  http://UK.answers.Yahoo.com/question/index?QID=20091129190055AA1nEsp

  He suggested to uninstall other versions of Yahoo messenger before installing the latest version. If it does not help to solve your problem, then go to Yahoo support.
  http://help.Yahoo.com/kb/index?locale=en_US&page=product&y=PROD_MSNG&PIR=qWKr06VibUkWf.Qpynpw1MiIKLy_mnW1Xh_iz.es9b2DJRQQvLHTQmI

  Sincerely,

  Marilyn

• I have difficulties to show my creative cloud from my PC. When I login from another computer to office, it is fine. Cloud is not compatible with windows 8? Any ideas on what could be the problem?

  I have difficulties to show my creative cloud from my PC. When I login from another computer to office, it is fine. Cloud is not compatible with windows 8? Any ideas on what could be the problem?

  Hello

  Creative cloud is compatible with windows 8.

  Please follow the steps below:

  1. Uninstall CC program and features

  2. run cleaning CC tool: use of the Adobe Creative Cloud cleaning tool to solve installation problems

  3. install Creative Cloud again, download and install Adobe Creative Cloud applications

  Hope this helps

  Thank you

  Varun

• Hello I have a macbook pro 2011 and in a few days I had my swelling of the battery and after that I ordered a new and only for a day, it uses my new battery began to swell again, what could be the problem? Help me, I am a student that I can't do it by new

  Hello I have a macbook pro 2011 and in a few days I had my swelling of the battery and after that I ordered a new and only for a day, it uses my new battery began to swell again, what could be the problem? Help me, I am a student that I can't do it by new

  is it because of power problems?

  Take it back to the Apple Store and ask them to check it out. It should be under warranty. Bring the MBP along too. It sounds like there might be a problem with it.

• My function paste decides to stop working randomly. What could be the problem and how could solve this problem?

  My function paste decides to stop working randomly. What could be the problem and how could solve this problem?

  A repair from the Vista DVD installation.  Don't forget to have a backup/restore point just in case.

  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

• I want to run ams 4.3 on my laptop and it says end abnormal program, what could be the cause

  After you have installed ams.4.3 on my laptop if I want to run it, it says end abnormal program, what could be the cause

  Hello

  1. what operating system do you use?
  2. have you checked if this program is compatible with your operating system?
  3. What is the full and exact error message?

  Please answer these questions that might help us helping you better. If you use windows 7 or vista you can try to install this program in compatibility mode and check.

  Reference:
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program
  http://Windows.Microsoft.com/en-us/Windows7/install-a-program
  http://Windows.Microsoft.com/en-us/Windows7/what-is-program-compatibility

• HDD and dvd are not recognized in the configuration menu, what could be the problem?

  The hard drive and dvd drive are not recognized on the configuration menu for my desktop Pavilion a4316f.  What is a controller failure?  A PCI controller can be used to replace the motherboard controller?

  dhobs,

  Anguish, that the suffering of the faulty motherboard has been aggravated by your actions. Why you decided to perform a restore (which re - formate the disk, erase all your data files (documents, photos, videos to misic,) is really amazing.)

  You had a viable BONE, work and the data store. You he clobbered with recovery. As explained, the 'tattoo' reads the embedded hardware configuration and will stop at the resumption of treatment if it detects a change.

  Only temporary help I can offer is to open the computer case and install a small 12v on the NVidia chip fan. IF the chip is not 100% burned, you can earn low enough time to reinstall the operating system and then add the map.

• My actions do not work when I play action, it looks like black and white squiggles.  Any suggestions on what could be the problem

  I'm still learning photoshop and are passed to the application of the measures.  When I apply the actions of the system, I get a black and white scribble everywhere in my picture.  I imported stocks of larger than Gatsby and they don't play all, play is grayed out.  When I first tried to import the actions they were greyed out.  Does anyone have suggestions on what to do?

  I see that you have used the Action of molten lead, and it is supposed to perform as in the screenshot.

  So if you wish, you can reduce the opacity of the most recent layer which has been created, it is layer 1.