Audio default HDMI output goes to "not connected" when the receiver is turned off and does not reset as defdault when the receiver is turned on

Similar Questions

• How to have separate video and audio over HDMI output Lenovo Thinkpad T410

  I have lenovo T410 and wanted to connect it to my TV high definition. Earlier had problems, but after buying SIIG Displayport to HDMI its job very well. In fact the video and Audio can now be read / listened to on my HDTV via HDMI. However, I have a separate 2.1 computer speaker system, which has much better sound output than my HDTV. Now if I want to see the video on HD TV via HDMI and audio output to speakers for laptop (connected to the 3.5 mm wired 2.1 speaker system), how to do that. I went to SmartAudio settings in the Control Panel, but there is no option of separates HDMI audio to the speakers only.

  I don't want to buy another cable with RGA Audio Converter 3.5 mm female port. Please suggest a direct solution.

  in win 7 do a right-click on the speakers on your lower right corner icon, select playback devices, click on speakers, click on set default, click OK and it should work (sound must come from your computer speakers or the computer 3, 5mm jack)

• Laptop frequently is off and does not restart even when the Start button / stop is held in

  I have a notebook dv7-3060us running Windows 7, some mornings (every few days or weeks), I find, powered out and does not.  In press and hold the power button for 5-10 seconds has no effect.  I have to unplug and remove the battery to restart.  What happened several times.  I tried it with the battery removed, and it fails again, then.

  A software problem can cause this?  I thought that holding the power button causes a material interruption and the BIOS takes over.

  Is there a known hardware problem which can cause this?

  Thank you

  Adam

  Hi Sean,.

  Thanks for the suggestion.  Unfortunately, the steps listed for a hard reset was precisely what was needed to market every day.  So, we did about 50 times.  The real issue was whether a software problem could cause the phone to require a hard reset every time.

  After not getting no response for a few weeks, I have restored your computer from a backup, I made after the update in the first place and then re-set everything.  So far, it has remained stable, which brings me to the conclusion that it is, in fact, a software issue.

  Kind regards

  Adam

• Apple TV 4th generation is missing optical audio cable Port. How can I connect to my receiver?

  I just replaced my Apple TV with the 4th generation model. The 4th generation model has more an optical audio port. How to connect Apple TV to my receiver with surround sound?

  Read this:

  Apple TV4 lack of Audio output - answers

• Need a hdmi to Rca cable to connect to the oldest pioneer flat screen tv

  try to unplug my tv dvd player that uses rca cables to I need an adapter cable. No connection hmdi on tv to plug the current

  HDMI is the only supported method while there is no guarantee with any converter. Even if it worked you have problems with resolution, aspect ratio and impossibility to view protected content (i.e. iTunes, Netflix). Functionality may cease at any time as well. Better to buy a new TV

• HP Pavilion HDMI out how can I connect to the VGA projector?

  I have a new HP Pavilion with a HDMI port Tower Summit and no vga port. What do I need connect my led projector that has only a vga connection?

  Hi Akela2

  You want HDMI adapter / VGA for it:

  http://h30094.www3.HP.com/product/SKU/10464062

  http://www.Amazon.com/GP/AW/d/B007PLL4CK/ref=redir_mdp_mobile?keywords=HDMI%20To%20VGA&QID=1404334963&ref_=sr_1_2&SR=8-2

  http://www.Amazon.com/GP/AW/d/B007PLL4CK/ref=redir_mdp_mobile?keywords=HDMI%20To%20vga%20converter&QID=1402998960&ref_=sr_1_3&SR=8-3

  Thank you

• Satellite C650D - Activate Wi - Fi is turned off and does not turn on

  Computer laptop Satellite C650D 006011 will not Wi - Fi switch on, even by Conectivity doctor or Instructions from Toshiba. F8 key does not appear on the monitor when the FN key pressed to activate a Wi - Fi connection.

  Laptop is about 12 months, a Wi - Fi connection worked initially. Have reinstalled the Wi - Fi drivers in an attempt to activate the e-mail... always to turn on Wi - Fi to connect.

  If the WLAN card is listed correctly in the Device Manager you should not reinstall WLAN driver. Driver WLAN has nothing to do with ON / OFF feature.

  > F8 key will not show on the screen when you press FN key
  Your problem is not WLAN driver and the functionality of the FN.
  Add the value of Toshiba install package.

  I can't get it for you because the description of the model 006011 C650D is unknown to me. Please recheck the model name and model number. You can find it on the bottom of your laptop placed on the sticker of Toshiba.

• DVD Drive Power Off and does not restart

  DVD Multi hunt in my ThinkPad W530 assignments after a while to save battery. But when I go into my computer, make a straight on the drive and click to turn on, nothing happens. The Player opens and allows me to put the disc in it, but no program on my computer does not detect the drive. Not Windows Explorer, not any program, not Windows Media Player to DVD burning. When I disconnect, then reconnect, the drive simply disappears from the hard disk.

  So far, the only way that I was able to get the DVD drive working again is by restarting the computer.

  What can I do?

  ThinkPad W530

  NVIDIA Quadro K1000M

  64-bit Windows 8

  Actually the above did not work. I uninstalled Cyberlink PowerDVD and DVD player started working as it was supposed to.

• Why is my menu clip off and does not not to premier pro

  the clip menu appears inactive how can I turn it back on? index everything, cause I wish you know how?

  Select a clip. I see that a clip is selected in the project Panel, but this Panel does not have focus, and no cutting is selected in the timeline panel, which has the focus.

• HDMI going offshore and on the Windows Vista system when it is connected to the TV.

  Original title device: Windows vista HDMI

  Eh_bien, I have connected to the computer with a HDMI, (TV with HDMI output) device) the system is windows vista, but always goes off and turn it back on, it turns off the HDMI device and allows the device installed on the pc. As always, I can do to stay enabled HDMI device?, the HDMI device is always connected.

  I appreciate your help.

  Hello

  Method 1:

  Perform a clean boot.

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note:

  After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  If this does not work then you can try updating the graphics card driver by visiting the manufacturer's website

  See also:

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3:

  Please check the same in another port and also try it on a different TV with working port known.

  For more information, you can also see:

  HDTV: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/HDTV-frequently-asked-questions

   

  TV on your computer: understanding signals TV and TV tuners

  http://Windows.Microsoft.com/en-us/Windows-Vista/TV-on-your-computer-understanding-TV-signals-and-TV-tuners

  Please answer back so that I can help you

   

• Re: Satellite U400-145: no option to select HDMI as HDMI output default

  Hello

  I followed the instructions in the manual its leader to the topic on the HDMI output.
  However, when I go to the sound control panel, there is no digital output device (HDMI) listed only the Conexant Chairman and SPDIF outputs.
  I tried the default SPDIF output, which did not work.
  The HDMI works fine for the image, but the absence of the sound through it is driving me crazy.

  I'm running VISTA (fully updated) on a U400-145

  Someone at - it ideas how I can get the HDMI to appear as an output option?

  Andy

  Hello

  Go to the control panel-> Sound-> playback tab
  There, you have to click to the right.
  Then mark the options; Show all disabled devices
  Then you should see the HDMI interface.
  Now, you could activate and chose as the default value.

  Welcome them

• Cannot get DTS/multi channel audio via HDMI

  Hello
  I'm trying to connect my VAIO SVT15112CXS to my Bravia HDTV via HDMI to get multi-channel audio (DTS/DD) from my Bravia HT (connected to the TV via optical) with no luck at all.

  I have the same setup for PS3 works well, is it cable or equipment.

  I have already updated all the drivers.

  When the TV is not connected I don't get an Audio HDMI option in the playback devices (I checked to show disconnected devices / disabled) and when it is connected I do not get an option to change the configuration of stereo speaker.

  This way I get only Stereo sound.

  I tried passthough HDMI via ffdshow config (installed K-Lite codec pack) and there is no sound in this way.

  Is there a solution? something escapes me?

  Thanks to all in advance,

  Thanks for your time and your response.

  I got it actually work! updated drivers audio and video (not Sony ones sugested, but later of Intel and Realtek) and now I have everything works as it should.

  The only minor problem is that Vaio Care now wants me to go back to the previous version of the driver, but I'll just ignore it.

  Everyone, try this if you experience this problem.

• MX800 No. audio on HDMI 2

  Hello

  I have a simple problem which does not make much sense, we must take a video and audio output of a MX800 so that we can record a conference and it is provide to be more difficult than expected.

  The firmware is TC7.3.4 and we find that no matter what we do, we cannot get audio on HDMI 2, which according to the manual should be supported, we can get audio on HDMI 1.

  The config looks OK

  * c xConfiguration Audio 2 HDMI output level: 0
  * c xConfiguration Audio output HDMI 2 Mode: on

  I understand that one of the DSP audio or perhaps multiple will be used for audio integrated on the system, but as the manual shows only 1 is used for each other should be available.

  We should expect audio out HDMI 2?

  See you soon

  Dave

  Hello

  There is no audio output 2 HDMI of MX800 single right now.   This is a documentation error that will be corrected.

  The associated API will be very probably removed in future versions of the software.

  Concerning

• Very slow connection on the WRT610N

  I bought a brand new WRT610N recently but didn't experience any improvement in speed, therefore began to study a little.

  I have a broadband cable, 30 Mbps connection.

  Cable modem is connected to a network adapter.

  An another output-power adapter is connected to the WRT610N

  now, when I connect my laptop through the router (wired or wireless makes no difference), my (upc speedtest) speed is about 5 Mbps.

  When I connect to the internet via cable to uplink on the router, I have 12 Mbps.

  When I connect directly to the cable modem, I have 28 Mbps.

  So, a big loss is caused by food taken thingies, I can get more quickly those who or stop using them at all. But what causes the loss of the router? All I can do about it? It shouldn't give me easily the 12 Mbit/s, it becomes itself?

  Any help appreciated.

  If connect you your computer to the WRT610N, you should be able to get on the same 28 Mbps you get from your cable modem.  Since you get only 5 to 12 Mbps wired, this suggests that there is probably a problem of basic configuration.

  (1) have updated the firmware on the router?  If so, after the update of the firmware, you reset the default router, and then configure the router again from scratch?  If you do not reset the router by default since the last update of the firmware, then please do it now and see if it solves your problem.  If you have saved a file of configuration of the router, DO NOT use it - you must configure the router again from scratch.  See "Reset to Factory Defaults" below.

  (2) using peer-to-peer (P2P) software?  If so, it is a known cause of slowdowns of router and disconnections.  The problem can occur even if you are not currently running the P2P software.  Stop using the P2P software.  It may take up to 5 days for your router erase from his memory.

  If the above does not solve your router, then proceed as follows:

  (3) Please indicate your ISP

  (4) Please indicate the make and exact model of your modem (not the WRT610N) number.

  (5) Please do the following test:

  Put your entire network.  Using an ethernet cable, connect your modem directly to your computer.  (Do not use the WRT610N for this test).  Turn on the modem and the computer.  Make sure you have an active Internet connection, then go ahead with what follows: (even if your Internet connection does not work, include this and move forward.)

  Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig/all" (with no quotes), and press the Enter key.   Copy all results in your next post.  To make the copy, highlight the results, and then use the keys copy (Ctrl-c) and paste (Ctrl-v) keys.  If your "IP address" does not begin with 192.168, then for security reasons, delete the latter half of your IP address.

  Reset to factory settings *.

  To reset your router by default, follow these steps:

  (1) turn off all computers, the router and the modem and disconnect from the wall.
  (2) disconnect all the wires of the router.
  (3) turn on the router and let it start up completely (1-2 minutes).
  (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
  (5) turn the router.
  (6) connect a computer cable to port 1 of the router (NOT to the internet port).
  (7) turn on the router and let it start up completely (1-2 minutes).
  (8) the power of the computer (if the computer has a wireless card, make sure it's off).
  (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
  (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Exit your browser.

  If you get this day without problem, try the Setup disk (or configure the router manually, if you prefer) and see if you can get your work and router configuration.

  If you can not ' response to... ". "in step 9 above, your router is probably dead. A report with this problem

  If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. Related to this issue.

  If you need additional help, please give the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.

  Please let me know how things turn out for you.

• local access only: unable to connect to the internet

  Recently, my laptop has trouble to connect to my home network. It's a laptop Dell and Windows Vista. This laptop used to connect wirelessly to the network without any problem, but lately, whenever it connects, it is said that "local access" and does not allow me to use the internet. " This problem occurred at the same time I replaced my old router with a new. Another laptop and other devices can still connect to the internet with this new router with no problems, but my laptop stops the message "local access only".

  After some research, I discovered that in typing "Cmd" in the search bar after clicking the start menu, run this program as an administrator, type "netsh int ip reset" in the command prompt, then by restarting my computer would fix my problem and my laptop would work very well and connect to the network and to the internet with no problems. However, as soon as my laptop is entered 'sleep' mode or has been disabled, when it was turned on again the problem persists and I have to follow the process of using the command prompt and restart the computer every time I turned on my laptop.

  As you can imagine, this process can be quite annoying and I would like to find a more permanent solution to my problem, especially since the past several times, I tried this workaround, it failed, so my laptop is once more without internet access. If anyone has any suggestions, it would be appreciated I am completely puzzled. Thanks for any help.

  Hello

  Method 1
  I suggest you try the steps from the following link:

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article: back up the registry in Windows Vista

  Method 2
  In addition, you can disable IPv6 to see if that nor does not affect the wireless adapter.

  To disable IPv6:
  (a) go to start, right click on the network, and then click Properties.
  (b) network and sharing window will appear, then click on manage network connections.
  (c) network connections window will appear. Here you can right click on the network adapter that you want to disable IPv6, then click Properties.
  (d) in the local area network connection properties window, clear the Internet Protocol Version 6 (TCP/IPv6) check box, and then click OK.

  Method 3
  I suggest you try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows