audio driver sounds, showing in Device Manager

Similar Questions

• No Apple USB driver in Windows 10 Device Manager

  Is there a way to retrieve the Apple USB driver in Windows 10 Device Manager.  I downloaded the iTunes 12.3.3 yesterday and now he is gone.

  I tried

  • plug into each of my Apple devices (iPod, iPad, iPhone, iPhone 4S 6)
  • restarting my computer
  • disabled my virus protection software
  • synchronization with different strings (some Apple, others not)
  • my devices restart and try again
  • Uninstalling iTunes and reinstalling
  • Uninstalling iTunes and goes back to and older version
  • make a Windows system to a restore point when I could synchronize my devices

  My main problem is that I need to sync my devices and iTunes does not detect them without the driver.  Windows can detect my devices and they appear in the file Explorer.  I am also able to get pictures and videos I've taken off the power unit and on my computer with no problems.

  Anything else I can try?  I'm out of ideas.  Thank you!

  This can help:

  If iTunes does not recognize your iPhone, iPad or iPod - Apple Support

  Refer to the section:

  If you are using a Windows PC

  and read carefully.  Depending on your version of Windows the Apple Mobile device driver may appear in different places.

  Other than that, the General adzice is to demolish EVERYTING associated with iTunes and reinstall.  See excellent iTunes for Windows troubleshooting page located at turingtest2:

  Troubleshooting problems with iTunes for Windows updates

  especially the section:

  Remove and then reinstall iTunes and other software components

• Don't see sound card in Device Manager

  Hello

  I installed today on my desktop - windows xp sp3 and all work well but I have 1 problem.

  Before I installed windows xp sp3, I got windows xp sp2 and the work of audio device without a problem, so I doubt that it's a software failure.

  Here is a picture of my device manager:

  http://i56.Tinypic.com/25aj31i.jpg

  And I check my BIOS Office and there is no problem and the sound card is enabled.

  I tried refreshing and the search for changes on the hardware in Device Manager and no change is
  and also I tried to install the driver software and realtek chipset and unfortunately no hope with that.

  Kind regards.

  If directx has not helped,

  then, the next thing I would try is to run a program called "autoruns" from microsoft.

  then after that it scans the system, find the audio drivers 'all' and them disabled.

  When I say 'everything', it may be that there is more than one driver or a corrupted or conflicting in your system.    something was mentioned involving realtek. so this is one of your objectives of drain plug, because it might be old or damaged or incompatiable.

  Then reboot and see if windows detects the sound system.

  If this is not the case, then have it search for a material via the Add/Remove Hardware Control Panel.

  If it still does not work, then you can try to reinstall the drivers of the homesite.

  If you have disabled the audio drivers via autoruns successfully, the re-installation may enter.

• I got a virus and now I have no sound. My device manager says that I don't have. I don't know how to solve this problem.

  I have no sound.  I went to my device manager and it says that I have not installed.  I'm not very computer, so I have no idea where to go from here.  If someone could help me I would be very happy!

  Hi ShariKB,

  ·         What is the exact error message in Device Manager?

  ·         How long have you been faced with this problem?

  ·         Did you do changes on the computer before the show?

  ·         You have security software installed on your computer?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you to follow the steps in the Microsoft article and check if it helps.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Method 2: I also suggest that you scan your computer with the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malware

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  Important: While running scan on the hard drive if bad sectors are found on the hard drive when scanning try to repair this area if all available on which data may be lost.

  Hope this information helps.

• my printers driver is hidden in Device Manager. Why?

  print files won't print on my Dell Photo AIO 966 printer. Following the instructions of troubloshooting I found in this forum to "remove the '.

  driver in Device Manager", the pilot is not visible in the Device Manager. Using the display tab, I ckicked on 'Show hidden devices' and

  find my driver here. When I click on the printer, the display shows the device works correctly. But in the Details tab under

  property, I chose the status of dev_node in the menu dropdown. A series of values displayed as follows: 0180200 a.

  dn_driver_loaded, dn_started

  driver dn_disabledable, dn_nt_enumerator and dn_nt. The problem that I would be in this area? Help!

  Dell does not include full features software/drivers for this model under win7, it uses the built-in drivers from windows update, and as such it doesn't have the same functionality as the drivers/software provided by the manufacturer of the printer

• COM3 showing in Device Manager but not in the list of printer port

  I have a Datamax Allegoro printer that uses a USB series converter. The poster converter as installed correctly (in devices and Device Manager) and received COM3.

  When I go to change the player of the printer to use the COM3 port, it is not in the list. How can I get the COM port appears in the list of printer ports?

  Note: this port was already there, but anyway when I was working on some of the settings (I changed the adapter to use COM1 temporarily as a test, then when I went to change it back, it was gone). I tried to uninstall the driver for the adapter and then re-install again, it did not work.

  Thank you.

  Use system restore to go back to an earlier date at the beginning of the problem. To run system restore, click Start-> programs-> Accessories-> System Tools-> system restore. Click on the box that says show more restore points.

  Good luck.

• Satellite C650-1CR - no webcam showing in Device Manager

  Hello

  I apologize if this question has already been posted. I have a Satellite C650-1CR; PSC08E-029001EN part number; Serial number 7A370192Q. Windows 7 64-bit operating system.

  The webcam, which has worked before, does not now in any program. In MSN it says I have no webcam; in Toshiba Face Recognition, he says camera failed to initialize. I have nothing to this fact - it has just stopped working. If I click on the Toshiba web camera application in the utilities section, nothing happens. The camera does not appear in Device Manager - there is no device images shown.

  I read through the advice here and you have downloaded the driver here, but that does not open. He goes as far as the extraction of the file, but then it will not run or open. I have the latest BIOS (update from Toshiba a couple of days). If I can avoid it, I don't really want to use the recovery disk I have many other things on my laptop that I don't want to lose.

  Any advice or help would be really appreciated. My son just moved to Australia, and it would be great for me to be able to use the webcam. I hope I gave enough information on the laptop and the problem.

  Thanks in advance for any help.
  Linda

  Hey Buddy,

  So if there is no webcam listed in Device Manager, you must check the installed programs in Control Panel > uninstall a program. Usually the webcam software should be in there and if yes remove it. Then, restart your computer.

  To remove all also run a registry cleaner like CCleaner which can remove old registry keys. It s freeware tool is therefore no problem to find using Google. After that you have to reboot your laptop again and then install the latest webcam software from the official page of Toshiba.

  Even after restart and you should be able to use the webcam again. Can you confirm this?

• Pavilion Slimline s5-1020: DVD drive not recognized in Device Manager

  My rarely used DVD player no longer works. Here are the things I have seen/made:
  -J' updated to Windows 10. It may or may not have stopped working before the update.
  -I update Windows automatically, and everything seems to be in order there.
  -The DVD seems to be operational, insofar as you can hear it turn when a disc is inserted.
  -Setup recognizes, and it is enabled; It is not at all in Device Manager or in the file Explorer.
  Based on the things I've tried, there are indications that it may be either a hardware or a software problem (or both?):
  
  SOFTWARE PROBLEM?
  I followed these as much as possible:
  http://support.HP.com/us-en/document/c03370738#c03370738_NoDriveWin8
  http://support.HP.com/us-en/document/c03370738#c01895589_resetpower
  http://h30434.www3.HP.com/T5/desktop-CD-DVD-read-only/read-this-for-CD-DVD-drive-with-burning-Missin...
  
  -I got disconnected/reconnected the drive.
  -J' tried various DVD I knew to do.
  -I don't have to update the BIOS, given warnings.
  - Nor did I mess with registry filters.
  -J' tried to find a Microsoft Fixit solution, but the one referenced somewhere in these pages don't apply to this OS - I think it was for Win 7.  I tried MS Control Panel convenience stores, but none of them worked.
  So I can't say whether or not it is a software problem.
  
  HARDWARE PROBLEM?
  -J' have set the boot on the CD order in configuration and the desktop with Windows 7 HP Pavilion system repair disc - nothing happened, he went straight to the HD (even if I had turned off).  So that leads me to believe it may be a hardware problem after all.
  
  Do I have other options at this point, except maybe buy another drive?  And in fact if I do, it is possible that one does not work either?

  While you are not alone in this problem, here's a thread that deals with her.

  http://h30434.www3.HP.com/T5/desktop-operating-systems-and-recovery/CD-DVD-drive-not-detected-after-upgrade-to-Windows-10/TD-p/5172346

  See if that helps

• WD5000AADS 500 GB hard drive. Windows XP Device Manager says it is installed and working properly, but it does not appear in my computer. Help!

  The disc was an external USB disk, but the fitting broke so I took off the adapter and I try to use it via its native SATA connectors. The disc is spinning and the computer know when it starts in Windows XP. It says new hardware found and go through the installation process. Windows finishes the installation, and says that everything is good with the world. I look in Device Manager and it says "this device is working properly" when I click on the drive properties. THEN..................... I click on MY COMPUTER and viola! No. DRIVE shown where the WD5000AADS should be there. There is nothing except my C: drive and my CD - DVD players.

  There are a few important (to me) information on this drive and I need to do.  HELP Please!

  Thank you

  twoiron

  Hi twoiron,

  • You are able to access the other USB devices on the computer?

  See the link below and run the Fixit tool available, check if it helps.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  http://support.Microsoft.com/kb/925196

  If him above fails tool Fixit check if the player is detected in disk management and has a drive letter assigned.

  To open disk management

  (a) from the start menu, click Run.

  (b) in the Open box, type diskmgmt.msc, and then click OK.

  If the drive is detected in disk management and the drive letter is missing, then assign a drive letter to the drive and check if that helps.

  How to change drive letter assignments in Windows XP

  http://support.Microsoft.com/kb/307844

• CD/DVD drive no appears in Device Manager and is not opening?

  Hi when I click to open my DVD/CD drive it does not open upward. Or it appears in Device Manager. I unplugged and plugged in I tried to use microsoft fix it. Nothing worked for me.

  Photo of him, not in Device Manager:
  http://i397.Photobucket.com/albums/PP56/nirvanaking95/dvdcddrivenotworking.jpg
  I JUST INSTALL WINDOWS VISTA SINCE WINDOWS 2000 IT HAS WORKED VERY WELL ON THE 2000!

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

• Display driver problem Code 12 Device Manager

  Ive has restore a Toshiba Satellite PA300-1 has 8 laptop with a Toshiba Recovery CD... Everything is fine except the display drivers.

  I believe that his family but the chipset intel 965 thought it was initially ATI?

  Ive run Everest and specc'd both say nothing... GPUZ says it is the Intel above

  In display properties of Device manager has a yellow! and he said that this device cannot find enough resources that it can use (code 12) which in my view is a conflict

  Please help as I want to my display drivers sorted

  Wingstmontana M.C.D.S.T.

  Hi the wings.

  While in the Device Manager, you can click on the view tab, click Show hidden devices.

  You can then uninstall all instances of the device in Device Manager and restart the computer.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• No output device and no sound card in Device Manager

  Hello I installed today on my Acer 7520 G laptop Windows7, I was pretty happy with it much but I have 1 problem.

  The arrival of the installation I had sound, but after windows updated itself the next time I got this done installed peripheral No. output message, I tried to reinstall the realtek drivers but no use, things to make it even worse, I can't find my sound card device in DEVICE MANAGER, it is as the sound card missing I had this problem on my Vista as well, but it worked after doing the system restore. Now even System Restore does not work, and I doubt that it is a hardware failure.

  I tried refreshing and looking for changes on the hardware in the Device Manager, no use. S

  Kind regards.

  Hello Fafarona,

  Can you tell what update may have caused the problem with your sound?
  Did you try and update your sound card drivers again after updates?

  You can try the following link: http://support.microsoft.com/gp/no_sound/

  It has an automatic FIXIT who could help restore your sound. It does help more sound issues.

  Answer please come back and let us know.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• No monitor showing in Device Manager

  I have a Hannspree 28 "monitor with a hdmi connection to an Asus Radeon 4890 graphics card. This facility works great under Vista Ultimate 32 bit in the default resolution of 1920 x 1200 screens...

  Since I installed Windows 7 64 bit, in a dual-boot scenario, I was unable to get Windows 7 works correctly in Normal mode, it works in safe mode, but only in 1600 x 1200.

  If I try a boot in Normal mode, then the sequence of boot stalls however I can open Win 7 Normal mode if I remove the Radeon 4890 in the element display adapter in Device Manager. Win 7 install the re - install the 4890, but can't do the correct resolution.

  With the latest ATI drivers installed in the card there is no monitor is displayed in Device Manager at all.

  Your help to fix this would be appreciated.

  GTS

  Hi Debra, Maryam and Aziz (and other stakeholders)

  The problem is almost solved, I say almost because I don't like having unexplained things always happening on my computer! The solution was obtained by marketing the Narrator function and use of inputs keyboard known to explore what was going on behind the BSOD (BlackScreenOfDeath) so that I now have the monitor works in glorious mode of 1920 x 1200.

  The solution actually came from my eldest son, when he asked if there was anything on the Toshiba TV (the other feed on the Radeon 4890). Yes, you have guessed the TV screen showed a perfect desktop but at a slightly lower resolution.

  Using Clone installation I got office showing on the Hannspree in seconds and, after a bit of investigation, I found that Windows 7/Asus Radeon or some another gremlin has decided that the main screen was my TV and that the Hannspree Monitor 2? -I don't know how this can happen.

  Suffice it to say that once I told Windows 7 that no. 2 was in fact my main monitor I could turn off the installation of clone and reset the Hannspree to its native 1920 x 1200 resolution, everything I want to do now is to say the 'system' that the Hannspree is main and monitor no. 1, but if I can't then I can live with n ° 2 - lol.

  Thank you very much for your efforts and I hope that it can match someone elses knowledge of the vagaries of Windows 7.

  Best wishes

  Gordon

• IV installed another drive hard, but in Device Manager it says offline, when I try to boot it says e/s error.i need help everytin.cant iv tried format the id really apreciate any help

  250 GB HARD disk installed but it is not recognized... device manag says its offline... doesn't I want to initialize it. said: IO error... impossible to format... tried so many things, even tried diskpart or cmd promt... no joy!   If any1 cud help id be greatfull Yes... oh ye also in Device Manager it has a circle with a red arrow facein down in... If dat help?

  IM so annoyed wit saying p.o.s.... Please help... tanx.

  If the utility of car manufacturers is unable to perform the test, it means that the drive has failed.

  Try it on another PC, see if it works it

• I have vista 32-bit, he sees not my new drive hard hitachi, in device manager it shows that it works correctly?

  Why my expoler does not see my new drive hard when it is in the device as o.k. Manager.

  Look for the drive in computer management, it may need to assign a drive letter.

  Change, add, or remove a drive letter
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-add-or-remove-a-drive-letter