Audio recording of Windows: the audio device does not work any

Similar Questions

• Satellite L300-19F and WXP - audio device does not work

  Hello

  I installed Windows XP Home edition on my Satellite L300-19f after change SATA compatibility I installed Windows XP Home edition and installed all the drivers and everything's fine, but the audio device does not work. I downloaded the driver from DOWNLOAD & support center, but he can not detect.

  BTW: he used to work on Vista.
  What should I do?
  And thank you

  -Download driver audio Realtek HD Realtek page.
  -Go to the Device Manager
  -Remove the sound card.
  -Remove the High definition Audio Controller
  -Restart the laptop.
  -Reinstall the Realtek HD audio driver

• Satellite U400-17R - audio device does not work after installing XP

  Hello

  I bought a model U400-17R with Vista Home. I formatted and installed Windows XP Professional download drivers XP Toshiba site.

  Everything works, but my Sound Device does not work. When I check in the Manager of devices the Sound Drivers are there and it says working properly.

  I'm lost... Can someone please help?

  Hello

  I think you have the same problem like me a few months ago.
  I installed Win XP SP2

  The t is not his work because I didn't install the patches MS; KB835221 & KB888111

  The patches must be installed as a first step, before the audio driver is installed.
  If you have already installed the audio driver, then you must remove (uninstall) before install you the patches Ms.

  PS: The MS patches are part of the SP3

• Webcam USB 2.0 on my laptop with windows vista error device does not work correctly

  Original title:

  I just plugged a usb2.0 webcam on my laptop with windows vista. It is loaded ok, but the device manager says that the device does not work correctly. Any ideas please.

  I just got a webcam via ebay and plugged into my laptop. I'm working on windows vista. He finds and load device software right away, no problem. But I can't work. go into my device manager it tells me that the device does not work correctly. Any ideas please.

  Hi Matthew,

  The first thing I would try is to connect the webcam to another computer to make sure that the webcam is not defective.

  Now, check out these links and return to the State of the question.

  When hardware installed in or attached to a computer doesn't work properly, it is often because of a driver problem.

  Here are a few common problems with drivers and the means to solve them.

  See the following link for more information:

  Tips for solving common driver problems

  Also check out the following link and run the fixit available.

  Hardware devices do not work or are not detected in Windows

  The fixit diagnose and solve problems with the equipment. (USB) Keyboard and mouse are not detected by the Manager of devices or when they do not work.

• Get an error window, the source folder does not contain any supported camera raw files

  Use the DNG successfully for some time now thanks to the Adobe forums after that I got my new 7 d. Always with the help of CS2 and is finally managed to convert the 7 d to the DNG format.

  Just be shot in raw of marriage because he needed a little more space than the 18 MP biggy.

  Now, DNG gives me an error message that the files source on my CF cards contain no support RAW files.  That is what it is? Any thoughts on why DNG cannot read RAW files smaller the 7 d?

  Big question here because it is a marriage to work on and I can not even begin to say how to slow DOWN, it will have to use EOS Digital Photo Professional from ADobe Bridge/ACR. I can just go die.

  A little help if someone knows why worth a glance.

  Are you sure you are using the latest (version 5.6) Adobe DNG Converter?

  You can download it here:

  Windows:

  http://www.Adobe.com/support/downloads/detail.jsp?ftpID=4620

  Mac:

  http://www.Adobe.com/support/downloads/detail.jsp?ftpID=4619

  As far as I know, the DNG Converter supports 7 d mRAW and sRAW files to DNG conversion. If you are sure you use 5.6 and your raw files do not work, can you post them somewhere so that I can download and St them?

  Another thing, you can try it for some raw files copy manually the CF card into a folder on your desktop, and then ask the DNG Converter to convert these local copies to the DNG format. If conversion mRAWs on your office's work, but their conversion on your card does not work, then it is possible that you have selected just the right folder on your card in the DNG Converter, or there may be another problem, just read the files on your card.

  Thank you

  David Franzen

  Quality engineer

  Adobe Systems, Inc..

• Audio device does not work on Satellite A300

  I have the new Satellite A300 for 3 days... and its not working. I have updated drivers and it did not help.

  I removed and installed again and it didn't work. I've tried everything. But when I look in Control Panel, everything is said to work, but it is not.
  And when I try to do an audio test it fails, error... and when I try to play music in media player it says: error. Does anyone have an idea, what the problem?

  > I have tried everything.
  Have you tried to install new OS by using recovery image Toshiba saved on the computer s portable HARD drive?
  And everything works well again. If you need instructions how to do this check please how Toshiba to the document under http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm

  Good luck!

• HP G71-449WM. Windows 7 64-bit. "The audio service does not work.

  I downloaded all the updates that I can find anywhere. My roommate has deletion of things on my laptop for 'performance' and now I have no sound. I go to my device manager in the computer and it is says my IDT HD audio CODEC works correctly. And my Intel(r) High Definition Audio HDMI does not work correctly. What should I do to get his new? The the small speaker in the far right of the task bar icon has an X on it, as she was mute. BUT it's not. Help? /

  Hello

  Open windows control panel, open administrative tools, and then open Services.  Verify that the following services are all displayed as status = started and the Startup Type = automatic

  Audio service

  Multimedia class Scheduler

  Windows Audio

  Windows Audio endpoint Builder

  Kind regards

  DP - K

• Satellite A-L50-19N - audio DTS does not work after update of Windows 10

  It is the most important thing in the drivers of toshiba, because without this driver, the sound is terrible...

  And now after the upgrade to 1511 he doesn't...

  I reinstalled IDT AUDIO latest driver is for 8.1 (2015 jan) and DTS Audio, which is for WIndows 10, but it does not work, I can it enable / disable EQs change, but nothing will change...
  
  WINDOWS 10 (1511)
  TOSHIBA SATELLITE L-50-A-19N

  DTS: 6.10.6491.0
  IDT: 1.2.41.0
  

  I fixed that, I updated its IDT Manager devices, and now Audio DTS driver works...

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Error: This device does not work properly because Windows cannot load the...

  I get this error message "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) "via a wired connection. And that's the Microsoft 6to4 adapt #7 and the same card but the #4 one.  Are these drivers or another file that I could use DL?

  Hi JasonBedgood,

  1. Once you get the error message?
  2. did you of recent changes on the computer?

  This error occurs if the required driver is not installed or the driver is damaged.

  I suggest that you update the driver for the device and check.

  How can I update the driver for network card on the computer

  1. click on Start, click Control Panel, and then double-click System.
  2. click the tab hardware , and then click Device Manager.
  NOTE: If you are prompted for an administrator password or for confirmation, type the password, or click continue.
  3. click on network adapters to expand.
  4. under network adapters, double-click the entry for Microsoft 6to4and then click driver .
  5. click on Update driver software.
  6. follow the Wizard update software driver to update the driver for NICs .

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the device driver update did not help then check the link below for one of the thread with the question and try the steps mentioned by Lionel Chen on January 9, 2008
  http://social.technet.Microsoft.com/forums/en-us/itprovistahardware/thread/3a503cdb-e61c-44BC-97c4-0b38b0e5f929/

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Wireless device does not work after downgrading from Windows 7 to Windows Vista.

  Original title: wireless device does not.

  recently, I got my os from windows 7 to vista, now my wireless device does not work. I checked the Device Manager and the report shows that my network controller driver is not installed and the modem on high definition audio bus device. I tried to install it, but in vain. What should I do?

  If your computer manufacturer does not have Windows Vista drivers available, you're probably out of luck.  Without drivers for these devices will not work.

  'spyc' wrote in the new message: * e-mail address is removed from the privacy... *

  recently, I got my os from windows 7 to vista, now my wireless device does not work. I checked the Device Manager and the report shows that my network controller driver is not installed and the modem on high definition audio bus device. I tried to install it, but in vain. What should I do?

• Hi my audio - pc does not work please help me

  Hi my audio - pc does not work please help me

  Uninstall the driver, reboot the system. The attempt to install the same driver for Windows Vista using Windows troubleshooting. Make a right click on the file executable/installer driver-> properties and select the Compatibility tab. Click on the box to check run this program in compatibility mode for option and select Windows Vista from the drop-down list. then try to install the device driver using run as administrator.

  Resources:

  If your computer has problems play a sound, try using the Audio playback problems resolution to solve the problem. For measures and additional information, see o ink below.

  Open the troubleshooting of Audio playback

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-troubleshooterOpen

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx?type=hardware

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

  In Windows 7

  Click Start > Control Panel

  Click on hardware and sound

  Under sound, click on manage audio devices

  Under playback (tab)

  Choose speakers you have in your output device

  Click Properties >

  Click levels (tab)

  check if the value is 100% >

  GoTo Enhancments > select Loudness balancing

  Apply and OK

  Should be much stronger now...

  For enhancment bit,.

  and if you have HD realtek soundmanager (R2.37) in your control panel

  Try a classic Equalizer setting