audio service not running__

Similar Questions

• Pavilion x 2-10-n109nl: Audio services does not

  Hi all,

  at one point in time and after any particular event, my laptop (Pavilion x 2-10-n109nl with Win10x64) started does not recognize the audio device. It displays a red x is close to the 'Volume' icon in the taskbar notification as if no audio device installed and lists an "unknown device" in Device Manager. Find that this unknown device has been "Intel ESS Audio Device (WDM)" and managed to install it with Intel drivers went back to 01/12/2016, so for the moment I had all audio devices is properly set up and works, but the Red Cross disappear and if I try to start Windows troubleshooting service it says "Audio services does not. This who can I try to do to get the problem resolved?

  Thank you all,.

  F.

  Hey @Ledbetter92,.

  Driver Audio Conexant is one that is registered in your page of drivers like Audio driver for you. This part is so good.

  Thanks for being patient and following all the steps! I very much appreciate the cooperation while trying to find a solution you did great! I wanted to make sure that I told you.

  You can try to do a reset of the BIOS. To reload the factory-installed BIOS configuration settings, perform the following steps:

  1. In the BIOS Setup utility, select the tab out.

  2. Select message Load Setup Defaults.

  3. Select Save Changes and Exit (pressing F5 and the Enter key will also load default configuration).

  4. Press ESC, then press Enter to exit the installation program.

  Source: reload the default settings

  Here is the document of HP Pavilion 10 - n100 x 2 detachable PCs-No Sound from computer speakers and Audio output connector that was created for this specific problem. You'll see below I have included the context of the document and the version numbers for each driver you need. Could you please check the versions currently installed on your laptop?

  Here are the steps in the document:

  No noise is through the computer speakers and the audio output connector headphone or external speakers are connected. An exclamation point (!) appears in the device on the audio device manager. This question is exposed on Windows 10.

  To resolve this problem, follow the steps to download and install the following SoftPaqs to update BIOS and install device drivers:

  1. Download and install the BIOS update.

  2. Download and install Chipset Intel graphics, camera and Audio Driver Pack.

  3. Download and install the Driver Audio Conexant.

  Updated HP Notebook System BIOS (Intel processors)

  • File name: SP73945
  • Version: F.06
  • Review: has

  Chipset Intel Graphics, camera and Audio Driver Pack

  • File name: SP72830
  • Version: 604.10146.2652.361
  • Review: has

  Conexant Audio driver

  • File name: SP72855

  • Version: 1.58.0.50

  • Review: has

  I would like to know how it goes

• HP G71-449WM. Windows 7 64-bit. "The audio service does not work.

  I downloaded all the updates that I can find anywhere. My roommate has deletion of things on my laptop for 'performance' and now I have no sound. I go to my device manager in the computer and it is says my IDT HD audio CODEC works correctly. And my Intel(r) High Definition Audio HDMI does not work correctly. What should I do to get his new? The the small speaker in the far right of the task bar icon has an X on it, as she was mute. BUT it's not. Help? /

  Hello

  Open windows control panel, open administrative tools, and then open Services.  Verify that the following services are all displayed as status = started and the Startup Type = automatic

  Audio service

  Multimedia class Scheduler

  Windows Audio

  Windows Audio endpoint Builder

  Kind regards

  DP - K

• audio service is not running

  I use a HP Pavilion dv4 laptop, product #WA683UA #ABA. There is a red X next to the "speaker" icon. When I move my mouse over the "speaker" icon, I saw the following message, "the audio service does not work."  How to fix this?

  Hello

  Hold down the Windows key and press R.  In the run box, type services.msc and press ENTER,

  Verify that the following services are all showing that status = started and the Startup Type = Automatic

  Audio service

  Multimedia class Scheduler

  Windows Audio

  Windows Audio endpoint Builder

  If you need to make a change to one of the above, just right-click the service and select Properties, and then in the drop-down list box next to "Startup Type", select automatic and click on apply to save the changes.  Then click on the Start button.

  Kind regards

  DP - K

• The audio service is not running

  Today, I turned on my laptop to discover that the sound did not work. I tried updating the drivers, restart the computer and try the default of repair tool, but nothing has worked so far. Any ideas?

  I have Lenovo Z50

  Thank you

  Hello! I recently solved this problem on my pc. AVG detected malware in the last patch of Win8.

  However, it is not a malware and relates to your audio services.

  Start AVG, click history, and then click quarantine.

  Click on the item with the EXACT time that you started windows was last updated, NOT get back anything else. Worked for me.

• HP Pavilion Notebook PC g7 - The Audio Service is not running

  I don't have sound on my PC for a few weeks, but when I use a headset it is solid. Today, I saw a message saying that the Audio Service is not running. What is going on?

  HP Pavilion Notebook PC g7

  #ABA product number A6Z29UA

  Hello

  Try the following.

  Download IDT Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55026.exe

  One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you are finished, download and reinstall the Chipset driver at the following link.

  Chipset Driver - Windows 7.

  Once this done, shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Allow Windows to fully - charge it will automatically load an audio driver, but let just this complete.  Then open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  Once this done, do a right-click the speaker icon in the taskbar and select playback devices.  'Speakers and headphones' left click once to highlight, and then click the Set Default button - check if you now audio.

  Kind regards

  DP - K

• No sound. Error "The Audio Service is not running"

  The sound stopped working on my Dell XPS M1210. I get the message "The Audio Service is not running" and the resolution of problems can't fix. Any suggestions?

  Hello

  See if that helps you.

  Do to Dell drivers and download page > equip your Dell model number > follow the prompts to find the drivers for your operating system > Search Audio drivers > download and install.

  http://www.Dell.com/support/drivers/us/en/usgen1/DriversHome/NeedProductSelection

  See you soon.

• Updates do not install, Sections of Vista does not and cannot start the Audio Service

  I try to install the updates on windows update but important as the service package 2 do not work, they start then stop and say failed code "WindowsUpdate_80070643"

  boxes keep popping up saying some files are damaged or not installed properly and that I should reinstall as a file call... system32\AVRT.dll. Windows Media is not no longer works.

  My Audio service is not running, I'm not sure that there is a problem in microsoft windows but the button to switch on the audio does not, and a box pops up saying it does not yet have another pop up says that everything works.

  any help? Please

  Hello
   
  a. updates have you tried to install?
  (b) button to switch on the audio of your computer are you using?
  c. what exactly happens when you try to run any audio/video file?

  You can try the steps outlined in the article below and check if this help.
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  For audio problem you are trying to run the troubleshooter which may help. It search common problems with your volume settings, your sound card or driver and your speakers or a headset.

  1. open the troubleshooting of Audio playback by clicking the Start button, then Control Panel.
  2. in the search box, type troubleshooting, and then click Troubleshooting. Under hardware and sound, click on the audio playback problems. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  You can also try to update check you and sound card driver if it works. The article below will help you do.

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Also, check if the following services are set to automatic.
  a. Windows Audio
  b. Windows Audio Endpoint Builder

  Here's how:
  1. click the Start button, type services.msc and press ENTER.
  2. go to any services mentioned above at the same time, right-click on it and select Properties
  3. click on the tab general, select automatic for startup type. Also click the Start button, if it is not started.
  4. click the Dependencies tab and make sure that all addictions services are set to automatic. Then click on the OK button.

  After return to that exact error messages we can help you better.

  Let us know if it works.

  Kind regards
  Umesh P - Microsoft Support

• I run Windows XP and my Windows Audio service is not listed in my Services window. It seems to be impacting directly to my computer detect my speakers. How do I fix this?

  I run a desktop computer with Windows XP.

  About two days ago my computer suddenly had no noise.  I checked the window sounds, voice and audio in the control panel.  Here, I discovered that the computer was grateful is no longer my speakers.  I have a Realtek HD Audio Manager, who still seems to recognize the speakers and can play demo sounds and effects in the Manager, but Windows itself can not see them.

  I tried to reset my computer, which had no effect.  I did a virus scan, which detected and deleted a file from my drivers folder called afd, but my sound problem was not fixed.  Research on this problem, I found a lot of references for the Windows Audio service, which may have been disabled.  I ran the line services.msc and in this window, I couldn't find one marked Windows Audio.
  A troubleshooting step suggested was to restore the computer to an earlier date, before the problem occurred.  This was not completely like my system has reported that it was impossible to restore to a previous period that I selected.
  Are there additional opportunities that I missed?  Are there resources for me to download the program on Windows Audio?  Are my signs of deeper systemic problems?
  Sincerely,
  Silencer

  writing in the new message: * e-mail address is removed from the privacy * _xp...

  I tried the Safe Mode system restore and chose the oldest checkpoint I could reach, 7 March. It took significantly longer to go, that he had previously, but still displayed the message, "cannot restore your computer to the point of control:" lists the control point for March 7 and then suggested another attempt at a different checkpoint. I do not understand why I wouldn't be able to do this work.

  As for the AV and firewall Suites, I wear McAfee. Could it prevent my restoration? I'll try it with McAfee and the Internet, temporarily disabled.

  McAfee may very well be the problem. When I was with Zone Alarm, I had to uncheck the setting "Start with Windows", then restart in Mode safe mode with command prompt and run %systemroot%\system32\restore\rstrui.exe from there to get it restored. The problem wasn't so much that ZA he would keep running, but when it came time to restart, prevented ZA SR to writing files necessary back to Windows at the time of reset. By preventing it from "Start with Windows", it would end as it should, so I want to reactivate ZA.

  And Yes, always unplug your ethernet (or disable your wireless network) while the firewall is down. Certainly don't want to pick up the mean, just trying to solve a common problem :-)

  SC Tom

• HP Pavilion 15 laptop: HP Pavilion - Audio Service does not

  Hi I recently bought a new HP Pavilion 15 and the volume down icon to the right, footer has an 'x' in a red circle next to it. When I go over it, it says "audio service does not work. I currently have no sound on the laptop.

  No idea how this can be fixed please?

  Thank you

  Hi Tom,

  Try the following.

  Download the Realtek Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66107.exe

  When finished, press and hold the Windows key and press R.  In the run window, type devmgmt.msc and press ENTER.

  Expand sound, video and game controllers.  Right click on the Realtek device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you are finished, download and reinstall the Chipset driver at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66094.exe

  After reinstalling, shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f9 to load the default values (sometimes it is f5, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Let Windows load completely - it can automatically load an audio driver, but let just this complete.  Then open your download folder, right-click on the installation of Realtek Audio program and select "Run as Administrator" to launch the installation.  Once this done, do a right-click the speaker icon in the taskbar and select playback devices.  Left click 'Speakers and headphones' (or speakers/HP) once to highlight and then click on the button set as default (it will be gray if already defined)-check if you now audio.

  If you have still no audio, hold down the Windows key and press R.  Type services.msc and press ENTER.  Search for audio Windows servive, right-click and select Properties.  If the service does not work, try to run.

  If you still receive the "Windows could not start the service windows audio on local computer» Error OX800706cc - the endpoint is double ' mistake, you're best bet is to do a Refresh as detailed on the link below.

  http://support.HP.com/us-en/document/c03538721

  Kind regards

  DP - K

• Help - Audio Service is NOT running - Windows Vista

  Hello

  I checked several websites & forums solution to my problem before asking the question here. A week Audio feedback from my computer started to give me problems. At first the audio suddenly stops during normal operation & would not return unless I restart my system. Then I tried to reinstall my audio driver & has managed to do this. But now, I see an 'X' mark next to the sound icon in my bar of tasks & says 'Service Audio does not work' here is the penalty shot I made:

  --> Administrative Tools Panel--> Services

  Plug & Play is WE & auto

  Multimedia is ON & Auto

  Windows Audio Endpoint Builder is stopped

  Windows audio is stopped.

  I tried to start Windows audio endpoint builder & the following error msg appears:

  "windows didn't start the generator service of audio endpoint of windows on the local computer.

  "Error 0 x 80070002: the system cannot find the file specified."

  Under path to the executable, I have seen that it is looking for a file named svchost.exe.

  File seems to be present at the location even if nothing seems to happen when I try double clicking on it.

  Please help solve this problem. Because I bought a HP laptop with Windows Vista, they don't give me a Vista DVD separate to try & reinstall everything again.

  Help

  Make sure that the

  Generator endpoint Windows Audio isenabled

  and

  Start the Service Windows Audio. (Found on the top left corner of the dialog box)

• activate the audio service I did everything what the engineers have suggested and I still get "...". Windows audio service is not enabled. ». Vista and the error are sometimes get is 1079.

  I did everything what the engineers have suggested and I still get "...". Windows audio service is not enabled. "I've tried everything suggested to obtain a permit.  I am running vista and the error is sometimes get is 1079.

  Help, please. randean

  Hello
  I tried, but I can't yet begin widows audio service even if the windows audio endpoint is fine. miracle happened just after I tried one of the recommended web u, it finally works. IM so happy.
  the solution is to change the name of connection for NT AUTHORITY\localservice
  Thank you very much
  Have a nice week

  Seera

• No sound - "either Windows Audio and Windows Audio services end Point Builder is not running."

  original title: no sound - Fix he said "either Windows Audio and Windows Audio services end Point Builder is not running."  What should do?

  When I ran Microsoft Fix it for audio, it says that it is unable to solve the problem.  The message was "two windows audio and Windows Audio end Point generator services must run for audio works correctly." At least one of these services is not running. "What should I do now?

  Content in double wire-
  "When I try to use anything related audioi on my computer (volume of the speaker, open iTunes, watch a video), a box appears that reads,"c\Windows\System32\MMDevApi.dll is not designed to run on Windows or it contains an error. " Try to install the program by using the original installation media or contact your system administrator or support software provider. "The mystery is that I have nothing to my computer to ask for that. I have not installed anything new or change the settings. It just started happening. Any advice? »

  Hello

  1. are you able to hear the sound after the error message?

  2. you have an an external sound card or internal, installed on the computer?

  Method 1:

  I suggest you to follow the steps and check.

  (a) click Start

  (b) type services.msc in the search box, and then press enter.

  (c) scroll down to Windows Audio and Windows Audio endpoint builder of Point

  (d) both should be started and set to automatic if one or both are arrested.

  (e) click the name to select it.

  (f) click on restart the service at the top left.

  (g) repeat for both if necessary. If some are not set to automatic, and then double-click the name and on the drop-down list to set the startup type to automatic and apply and ok your way out.

  Method 2:

  I suggest you to run the automated FIXIT from the link below. You can also follow the other steps and check.

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  Method 3:

  If you have a sound card, I suggest you uninstall the audio driver from the Device Manager and and then install the latest audio driver version from the sound card manufacturer's website.

  To uninstall the Device Manager sound, proceed as described in the link below.

  Open the Device Manager

  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Device-Manager

  Find the audio driver in the list, do a right click and Uninstall.

  You can also download the drivers from the link below.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 4:

  If the steps do not help, I also suggest you to run a scan of the System File Checker .

  Click on the link mentioned below for more information about the System File Checker analysis

  http://support.Microsoft.com/kb/929833

  Hope this helps and keep us posted.

• My audio service does not work - I can not use my pc on mode safe by minegold. How to return to normal

  my pc starts only in safe mode and I like the audio service is not running.

  for example, when I play something with you tube, I can see the video, but

  without sound.

  Hello

  Audio service does not work in Mode without failure.

  The services are very limited in safe mode.

  1. Close all running programs and open the windows if you are back on the desktop.
  2. Click on the Start () button.
  3. In the search box of the Start Menu, type in msconfig
  4. Then press enter on your keyboard.
  5. The System Configuration utility opens
  6. Make sure that Start Selection is set for Normal start.
  7. Click the Startup tab.
  8. Make sure you start is not checked
  9. Press the apply button and then press the OK button.
  10. Click the restart button to restart your computer.

  See you soon.

• The Windows Audio Service does not start

  I have no sound at all. Show my audio device is installed and working. I get a message that the Windows audio service and audio end point service Windows (I think (does not start.)

  Hi JamesSimpson11759,

  ·         What happens when you try to start the Windows Audio Service? You receive an error message or error code?

  ·         Did you do changes on the computer before the show?

  I suggest you to run the Microsoft Fixit and check if the problem still persists.

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  You can also view the article mentioned for more information:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Let us know the results.