Audio services does not

Similar Questions

• Pavilion x 2-10-n109nl: Audio services does not

  Hi all,

  at one point in time and after any particular event, my laptop (Pavilion x 2-10-n109nl with Win10x64) started does not recognize the audio device. It displays a red x is close to the 'Volume' icon in the taskbar notification as if no audio device installed and lists an "unknown device" in Device Manager. Find that this unknown device has been "Intel ESS Audio Device (WDM)" and managed to install it with Intel drivers went back to 01/12/2016, so for the moment I had all audio devices is properly set up and works, but the Red Cross disappear and if I try to start Windows troubleshooting service it says "Audio services does not. This who can I try to do to get the problem resolved?

  Thank you all,.

  F.

  Hey @Ledbetter92,.

  Driver Audio Conexant is one that is registered in your page of drivers like Audio driver for you. This part is so good.

  Thanks for being patient and following all the steps! I very much appreciate the cooperation while trying to find a solution you did great! I wanted to make sure that I told you.

  You can try to do a reset of the BIOS. To reload the factory-installed BIOS configuration settings, perform the following steps:

  1. In the BIOS Setup utility, select the tab out.

  2. Select message Load Setup Defaults.

  3. Select Save Changes and Exit (pressing F5 and the Enter key will also load default configuration).

  4. Press ESC, then press Enter to exit the installation program.

  Source: reload the default settings

  Here is the document of HP Pavilion 10 - n100 x 2 detachable PCs-No Sound from computer speakers and Audio output connector that was created for this specific problem. You'll see below I have included the context of the document and the version numbers for each driver you need. Could you please check the versions currently installed on your laptop?

  Here are the steps in the document:

  No noise is through the computer speakers and the audio output connector headphone or external speakers are connected. An exclamation point (!) appears in the device on the audio device manager. This question is exposed on Windows 10.

  To resolve this problem, follow the steps to download and install the following SoftPaqs to update BIOS and install device drivers:

  1. Download and install the BIOS update.

  2. Download and install Chipset Intel graphics, camera and Audio Driver Pack.

  3. Download and install the Driver Audio Conexant.

  Updated HP Notebook System BIOS (Intel processors)

  • File name: SP73945
  • Version: F.06
  • Review: has

  Chipset Intel Graphics, camera and Audio Driver Pack

  • File name: SP72830
  • Version: 604.10146.2652.361
  • Review: has

  Conexant Audio driver

  • File name: SP72855

  • Version: 1.58.0.50

  • Review: has

  I would like to know how it goes

• HP Pavilion 15 laptop: HP Pavilion - Audio Service does not

  Hi I recently bought a new HP Pavilion 15 and the volume down icon to the right, footer has an 'x' in a red circle next to it. When I go over it, it says "audio service does not work. I currently have no sound on the laptop.

  No idea how this can be fixed please?

  Thank you

  Hi Tom,

  Try the following.

  Download the Realtek Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66107.exe

  When finished, press and hold the Windows key and press R.  In the run window, type devmgmt.msc and press ENTER.

  Expand sound, video and game controllers.  Right click on the Realtek device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you are finished, download and reinstall the Chipset driver at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66094.exe

  After reinstalling, shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f9 to load the default values (sometimes it is f5, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Let Windows load completely - it can automatically load an audio driver, but let just this complete.  Then open your download folder, right-click on the installation of Realtek Audio program and select "Run as Administrator" to launch the installation.  Once this done, do a right-click the speaker icon in the taskbar and select playback devices.  Left click 'Speakers and headphones' (or speakers/HP) once to highlight and then click on the button set as default (it will be gray if already defined)-check if you now audio.

  If you have still no audio, hold down the Windows key and press R.  Type services.msc and press ENTER.  Search for audio Windows servive, right-click and select Properties.  If the service does not work, try to run.

  If you still receive the "Windows could not start the service windows audio on local computer» Error OX800706cc - the endpoint is double ' mistake, you're best bet is to do a Refresh as detailed on the link below.

  http://support.HP.com/us-en/document/c03538721

  Kind regards

  DP - K

• My audio service does not work - I can not use my pc on mode safe by minegold. How to return to normal

  my pc starts only in safe mode and I like the audio service is not running.

  for example, when I play something with you tube, I can see the video, but

  without sound.

  Hello

  Audio service does not work in Mode without failure.

  The services are very limited in safe mode.

  1. Close all running programs and open the windows if you are back on the desktop.
  2. Click on the Start () button.
  3. In the search box of the Start Menu, type in msconfig
  4. Then press enter on your keyboard.
  5. The System Configuration utility opens
  6. Make sure that Start Selection is set for Normal start.
  7. Click the Startup tab.
  8. Make sure you start is not checked
  9. Press the apply button and then press the OK button.
  10. Click the restart button to restart your computer.

  See you soon.

• AUDIO SERVICE DOES NOT

  Audio service does not... I get a message saying... this computer cannot play audio because the Windows Audio Service is not enabled... even after that activation still does not work... its recognizingal my reading, sound and recording... says they're all works... but still no sound... got a new sound card, still nothing

  Hello

  Refer to the steps below to solve the problem.

  Step 1:

  I suggest to refer to the link below and follow the step by step guide to fix issues with the no sound in Windows Vista.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Step 2:

  You can also check out the link below which provides an automatic fixit to solve the problem and also provides manual steps.

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  If the steps above do not help you can also refer to the link below and follow the suggestions given by Linda Yen in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/w7itproperf/thread/56d0bf26-d5a7-42FD-9b95-d6ba89c53f6e

• No sound (audio service does not start, error 1079)

  I have no sound on my laptop.when I have troubleshooted the program that is to show that audio service does not work when I tried to start the audio service is not starting and showing an ERROR: 1079.

  I tried several times but it's showing the same...
  is there a solution for this problem?

  Hello

  Did you change your computer?

  This error code 1079, pop when you try to start the audio service?

  Method 1:

  (a) click Start, type services.msc and press ENTER.

  (b) double-click the "Windows Audio" service

  (c) click on the tab to open a session.

  (d) click Local System account, and then click OK.

  (e) right click on the "Windows Audio" service and then click Start.

  (f) follow the same steps for the service "Windows Audio Endpoint Builder.

  (g) check if the problem persists.

  I suggest you follow the link and check.

  Services do not start, and you receive an error 1079 on a computer that is running Windows Server 2008, Windows Vista, Windows 2008 R2 or Windows 7

  http://support.Microsoft.com/kb/2478117

  Method 2:

  I suggest to uninstall the sound card in Device Manager and then reinstall it.

  Follow these steps:
  1. click on start and then type devmgmt.msc in the start search box and press on enter.
  2. from the list of devices, expand sound, video and game controllers.
  3. right click on the sound card, and then click on uninstall.
  4 restart the computer.

  After restarting the computer, sound card get installed automatically. Update the drivers manually for your sound card.

  Make sure that you have installed the Windows

  Method 3:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

• Audio service does not work, error 0 x 80004005: unspecified error

  I have problems with my laptop in regards to the audio service does not. The sound icon has an x on it and ran the SCP prompt automatically update/fix drivers without success (may have spelled promot hurt, but it was the solution to many similar forum messages). I also tried to uninstall the audio driver and put it back, however when I run the driver installation an error message appears and says that Windows Audio is not running and needs in order to perform the installation. I went to the system administrator and seen the services menu and went to windows audio properties. I tried from the program and the error message "error 0 x 80004005: unspecified error" comes up. All dependent services for the Windows Audio are running, so I came to a dead end. The only thing I can think of that would make the audio not working do not is my battery. My battery is in poor condition and needs to be replaced, so I always us the AC cord to power the computer. Depends on Windows Audio battery somehow or something of this nature? If so, is there anyway around this until I can buy a new? Thanks for your help. Clay

  You say you have Vista - therefore, you the Vista drivers, drivers for W7!

  See you soon,.

  Jerry

• Receive an error message "Audio service does not ' and 'volume' in the list of notifications is grayed out

  * Original title: Audio Service does not. I have audio but no volume control in the taskbar, also "" volume"in its notification list is gray out

  Using Windows 7. My Audio service does not. I have audio but no volume control in the taskbar, also "" volume"in its notification list is grayed out.

  Hello

  1. when exactly you get the error message?

  2. do you see a red brand 'X' indicating that the audio output does not work with error message?

  Please follow the steps below and we update with the results.

  Method 1:

  a: you can try to enable the taskbar.

  b. right-click on the taskbar (the bar at the bottom of your screen), select Properties.

  c. click the Notification area.

  d. then, under system icons, select the Volume that you want to display

  Run Microsoft Fix it the following article and check.

  http://support.Microsoft.com/default.aspx/KB/945011/en-us

   

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

   

  Method 2: Ensure that the Windows audio service is running on the computer.

  a. open administrative tools by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Administrative Tools.

  b. double-click on Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  c. right click on Windows Audio serviceand then click Properties.

  d. under the general tab, next to startup type, make sure that Automatic is selected.

  e. also make sure that the service is began to.

   

   

  Method 3:

  Tips for solving common audio problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

   

   

  Method 4:

  Install the latest audio drivers on the computer by visiting the sound card manufacturer's Web site and check if it works.

   

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

   

  Note: visit the manufacturer's Web site to download the latest audio drivers

  For more information, see the article:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows?T1=Tab03

  Let us know if it helps!

• My Acer TravelMate 3273WXMi audio service does not work properly. I use an Audio_Realtek_6.0.1.5413_VistaX86

  Hello
  My Acer TravelMate 3273WXMi audio service does not work properly. I use an Audio_Realtek_6.0.1.5413_VistaX86 on W7 driver. The problem is no outside speaker and not micro.

  2 things:

  -Why you are using Vista drivers with W7? No, there is no specific driver for W7 (search the website of Acer support for your machine).
  -you will never get full nombreauses for help, these drivers.
  See you soon,.
  Jerry

• HP G71-449WM. Windows 7 64-bit. "The audio service does not work.

  I downloaded all the updates that I can find anywhere. My roommate has deletion of things on my laptop for 'performance' and now I have no sound. I go to my device manager in the computer and it is says my IDT HD audio CODEC works correctly. And my Intel(r) High Definition Audio HDMI does not work correctly. What should I do to get his new? The the small speaker in the far right of the task bar icon has an X on it, as she was mute. BUT it's not. Help? /

  Hello

  Open windows control panel, open administrative tools, and then open Services.  Verify that the following services are all displayed as status = started and the Startup Type = automatic

  Audio service

  Multimedia class Scheduler

  Windows Audio

  Windows Audio endpoint Builder

  Kind regards

  DP - K

• Audio service does not not after download of Creative, restarts, error 0 x 80070002, the system cannot find the file specified

  Yesterday, I downloaded and installed updated Creative to my its Soundblaster card from Windows Update.  It lead me to a large download of Creative for its console related sound and SW, and things worked fine.  When I restarted this morning, there was a horrible loud hum while Windows was loading, and I made a hard stop.  When I rebooted, the buzz was gone, but the icon in the status bar indicates that the sound was off.  The sound message indicates that the audio service is not running.  I tried to restart the computer several times, but the results were the same.  I tried to restart the audio service of the Task Manager, but got an error message 0 x 80070002, the system cannot find the file specified.  Where should I go from here?

  Hi Jfklinger,

  This problem occurs because some legacy applications use files or components that were developed prior to Windows Vista. The names of these audio components may be different in Windows Vista. If the calling application uses the hard-coded file names, the new files and components could not be found.

  To resolve this problem, use one of the following methods to change the audio settings for a device.

  Method 1: use the order Volume of Windows

  To use the Volume of Windows command to change the audio settings for a device, follow these steps:

  1.right - click on the speaker icon in the notification area, and then click devices recording or reading.
  2. double-click - click the device for which you want to set the parameters. For example, double-click on Microphone.
  3. click on the levels tab.
  4. move the cursor upwards or downwards to set the desired volume level, and then click OK.

  Method 2: use Control Panel

  For control panel allows you to change the audio settings for a device, follow these steps:

  1. click on Start, click Control Panel, click hardware and soundand then click sound.
  2. click on the tab playback or recording .
  3. double click the device for which you want to set the parameters. For example, double-click on Microphone.
  4. click on the levels tab.
  5. move the cursor upwards or downwards to set the desired volume level, and then click OK.

  You may receive an error message when you run an application that uses the recording feature or audio playback in Windows Vista
  http://support.Microsoft.com/kb/930095

  Previous post: the result.

  Bindu S - Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Audio services does not... additional options for troubleshooting does not

  Recently, I restarted my laptop and after restarting, I couldn't play any music media player, iTunes or xbox music. After hovering over the icon of the sound, he says that the Windows Audio service is not running. After troubleshooting the windows troubleshooting options seemed empty and not answered. It is the same for the control panel when I tried to open it manually. Someone please help this situation is disturbing. I use a Lenovo IdeaPad touch P500 running windows 8.1. If it helps, this is happening after the recent update to annex one or two days ago.

  AVG is installed?

  If AVG has therefore been reported recently, ask questions as in the next thread that has any suggestions to remedy the situation:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows8_1-hardware/Windows-audio-cant-be-started-error-0x800706cc/2f3cffd7-62e3-4b18-a604-7c1438e6a04a?page=1

• The Windows Audio Service does not start

  I have no sound at all. Show my audio device is installed and working. I get a message that the Windows audio service and audio end point service Windows (I think (does not start.)

  Hi JamesSimpson11759,

  ·         What happens when you try to start the Windows Audio Service? You receive an error message or error code?

  ·         Did you do changes on the computer before the show?

  I suggest you to run the Microsoft Fixit and check if the problem still persists.

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  You can also view the article mentioned for more information:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Let us know the results.

• audio service does not error.

  I have a HP Envy 700-074 and'm running Windows 8.1.

  The displayed error is - Service Audio does not work.  It appeared this morning - never seen before.

  Thank you

  Hello

  You can resolve this problem by restarting the audio service.

  Right-click on the Start button.

  Click prompt (admin)

  Net stop type AudioSrv and press ENTER to stop the service

  Type net start AudioSrv and press ENTER to start the service.

  This should solve the problem.

  *************************************************************************************
  Charles Thangaraj

  -Say 'Thank you' by clicking on the star of congratulations in the post helped you.
  -Please indicate the position that solved your problem as "acceptable Solution".

• It says audio service does not work - why? I never changed any settings or anything and now no sound?

  What happened all of a sudden.  I did the virus scan this am and nothing appeared.  This has never happened before, and when I tried to pull trouble - he said go into Device Manager, but there was nothing there: no device?

  Hello

  Follow these methods and check if that helps:

  Method 1:

  I suggest to start in safe mode and check if you can view the devices in Device Manager.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:

  You can also check your profile for corruption:

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  Method 3:

  I suggest you follow the troubleshooting steps form the article and check if it helps.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows