Authentication for wireless access

Similar Questions

• Increase the length of character allowed for wireless access PIN code

  I need to know how to increase the maximum number of digits allowed when you enter the PIN method of Wi - Fi.  I have a new home wireless router that requires a PIN 14 digits to access the wireless system.  My Vista operating system allows only 8 characters maximum.  I can not access my wireless network.  Is there a solution of regedit?

  Hello

  Assuming that you mean by "PIN Wi - Fi", the wireless security password.

  You must configure the security of the router to match the capacity of the computer.

  Put the router to WPA or WPA - AES, and the computer will adapt.

  In general.

  Of the weaker for wireless security, more strong capacity is.

  No security

  Switch Off SSID (even has No Security. SSID can be sniffed easily even if it is turned off)

  MAC Filtering___ (Band Aid if nothing else is available, MAC number can be easily Spoofed).

  WEP64___ (Easy, "Break" by knowledgeable people).

  WEP128___ (a little more difficult to activate, but "Piraté" too).

  -------------------

  The three above are not considered safe.

  Safe starts here at WPA.

  -------------------

  WPA-PSK__(Very Hard to Break).

  WPA-AES__(Not functionally Breakable)

  WPA2___ (not functionally breakable).

  , Note 1: WPA - AES the current interpretation level entry of WPA2.

  Note 2 : If you use WinXP SP3 bellows and not updated, you will need to download the fix from Microsoft WPA2. http://support.Microsoft.com/kb/893357

  Documentation of your devices (router wireless and computer wireless card) must indicate the type of security that is available with your wireless hardware.

  All devices MUST be set to the same level of security using the same password.

  Therefore, security must be set according to what is the best possible one of the wireless devices.

  I.e. even if most of your system may be able to be configured to the maximum with WPA2, but a device is able to be configured for maximum of the WEP Protocol, to the whole system must be configured to WEP.

  If you need more security and a device (such as a wireless card that can only do WEP) is now better security for the entire network, replace with a better device.

  Definition of wireless security - http://www.ezlan.net/Wireless_Security.html

  The fundamental differences between WEP, WPA and WPA2 - http://www.ezlan.net/wpa_wep.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Test command of the AAA for EAP - TLS authentication for wireless users

  Hi all

  Can anyone suggest me the test command to verify the eap - tls authentication for the Cisco WAP's wireless.

  If it's an authetication jump we can use the command to test the connection below

  Radius of group aaa Testwap-01 #test [email protected] / * / o4 & yJ) NoL$ new-code %0
  Trying to authenticate with the server radius group
  User successfully authenticated

  But eap - tls is not delivered with the password. He insists that for the user name.

  We strive for remote location then test remotely before production.

  If someone help pls in that if we have a command to test or debug command to test this authentication.

  EAP - TLS requires a client certificate. How can you have a simple command that analysis without loading any certificate on the router/switch? It does not exist. This is why eap - tls is not considered an easy to deploy eap method: because it can go wrong on several levels.

  The aaa command test performs a PAP authentication, therefore, it tests the connectivity of the base RADIUS and name of user and password.

  If it works, the only thing that can break for eap - tls are certificates, as well as the radius server will be able to tell if something worng.

• Cisco ISE 1.3 using 802.1 x authentication for wireless clients

  Hello

  I fell into a strange question attempts to authenticate a user more wireless. I use as PEAP authentication protocol. I have configured my strategy of authentication and authorization, but when I come to authenticate the selected authorization policy are by default that denies access.

  I used the 802. 1 x conditions made up to match the computer authentication, then the user authentication

  AUTHENTICATION OF THE COMPUTER

  football match

  Box

  Wireless

  Group of ads (machine)

  AUTHENTICATING USERS

  football match

  Box

  Wireless

  Ad (USER) group

  has been authenticated = true

  Here are the measures taken to authenticate any ideas would be great.

  Request for access received RADIUS 11001
  11017 RADIUS creates a new session
  15049 evaluating Policy Group
  Service evaluation 15008 selection policy
  15048 questioned PIP
  15048 questioned PIP
  15048 questioned PIP
  15006 set default mapping rule
  11507 extract EAP-response/identity
  12300 prepared EAP-request with PEAP with challenge
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12302 extracted EAP-response containing PEAP challenge-response and accepting as negotiated PEAP
  12318 has successfully PEAP version 0
  12800 first extract TLS record; TLS handshake began
  12805 extracted TLS ClientHello message
  12806 prepared TLS ServerHello message
  12807 prepared the TLS certificate message
  12810 prepared TLS ServerDone message
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  12318 has successfully PEAP version 0
  12812 extracted TLS ClientKeyExchange message
  12804 message retrieved over TLS
  12801 prepared TLS ChangeCipherSpec message
  12802 completed TLS prepared message
  12816 TLS handshake succeeded
  12310 full handshake PEAP completed successfully
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  12313 PEAP inner method started
  11521 prepared EAP-request/identity for inner EAP method
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  11522 extract EAP-Response/Identity for EAP method internal
  11806 prepared EAP-internal method call offering EAP-MSCHAP VERSION challenge
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  11808 extracted EAP-response containing EAP - MSCHAP VERSION challenge response to the internal method and accepting of EAP - MSCHAP VERSION such as negotiated
  15041 assessment political identity
  15006 set default mapping rule
  Source sequence 22072 Selected identity
  15013 selected identity Source - AD1
  24430 Authenticating user in Active Directory
  Identity resolution 24325
  24313 is looking to match accounts at the junction
  24315 account in the domain
  24323 identity resolution detected single correspondent account
  Application for CPP 24343 successful logon
  24402 user Active Directory authentication succeeded
  Authentication 22037 spent
  EAP-MSCHAP VERSION 11824 passed authentication attempt
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  11810 extract EAP-response to the internal method containing MSCHAP stimulus / response
  11814 inner EAP-MSCHAP VERSION successful authentication
  11519 prepared EAP-success for the inner EAP method
  12314 PEAP inner method completed successfully
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  ISE 24423 was not able to confirm the successful previous machine authentication
  15036 assessment authorization policy
  15048 questioned PIP
  15048 questioned PIP
  Looking 24432 user in Active Directory - xxx\zzz Support
  24355 fetch LDAP succeeded
  Recovery of user 24416 of Active Directory groups succeeded
  15048 questioned PIP
  15048 questioned PIP
  15004 Matched rule - default
  15016 selected the authorization - DenyAccess profile
  15039 rejected by authorization profile
  12306 successful PEAP authentication
  11503 prepared EAP-success
  11003 returned RADIUS Access-Reject
  Endpoint 5434 conducted several failed authentications of the same scenario

  Windows will only be machine authentication when you start, then test you can't just disconnect/connect the pc, you will need to restart. The solution is called cisco anyconnect nam and eap-chaining.

• WRT54G - implementation of password for wireless access

  I am sure that the answer is simple and here somewhere - but I was not able to find it in 2 days.

  I'm just trying to find a way to implement a simple password if the our laptops wireless & the wii and ps3 can access the internet, but the neighbors cannot. =)

  I managed to set up once, but the numbers were about 27 characters and it was an accident, and - I couldn't get a new pc to connect with any numbers, tho - my son somehow managed to get the wii connected...

  I looked through other and the connection name & passwords were pretty basic.  How to set a place for my home lan based?

  Thank you!! =)

  Set up your security here.

• Install printer HP F4580 for wireless access

  Hello

  I'm putting in place the printer HP F4580 to access wireless, but without success. Can someone send me the exact steps or processes that I must follow to set up my printer to wireless? I followed the installation from the CD and I could see the printer in the Network Wizard wireless as "hpsetup". Now what should I do?

  Thank you.

  Try using the instructions on page 5 of the Manual.

• Interactive report (for Public access)-how to remove/reset the filters

  I have an Application that uses an authentication for "Public Access" scheme, which has a few interactive reports that can be viewed by anyone in our organization without a login screen.
  
  What I found is, if someone put a filter on the report that he remains on the report and stays on for the next user who visits the application.
  
  Is it possible to have the interactive report be reset default settings or remove filters that are applied by the previous user?
  
  Or is it a side effect, it is public, and report parameters are not fixed to a specific user?

  Hello

  Try the overview of the authentication page to the Public and see if it helps
  http://download.Oracle.com/docs/CD/E14373_01/AppDev.32/e11838/bldr_pgs.htm#CJGJDHCI

  BR, Jari

• My wifi limited shows, no card wireless for internet access or access point problem

  Hi, I tried to connect with wifi, it shows connected but wrote 'limited' by the side. and below his writings no internet no access. I tried troubleshooting but it says wireless access point or no fixed adapter problem. can sum1 if you please help me with this problem

  Hi Dimma,

  What is the brand and model of your computer?

  This could be caused due to various reasons.

  -Due to the wireless router settings.

  -Due to the IP address.

  Follow the following troubleshooting methods:

  Method 1: I suggest you to reset the wireless router and check if this solves the problem manually.

  Consult the router's manual to know how to manually reset the router.

  Method 2: Reset TCP/IP and check if this solves the problem.

  Follow these steps:

  a. press the Windows key (start screen will popup), type cmd on the right click of the screen prompt, select run as administrator.

  b. at the command prompt, copy and paste (or type) that follows the command, and then press ENTER:
  netsh int ip reset c:\resetlog.txt

  c. Note: If you do not specify a path of the directory for the log file, use the following command:
  netsh int ip reset resetlog.txt

  d. restart the computer.

  
  

  Method 3: If you use WEP encryption change to WPA or WPA 2.

  Hope this helps and let us know if you need help. We will be happy to help you.

• Errror: The certificate chain was issued by an authority that is not approved. connecting to a wireless access point

  I can't understand the process of certificates, by connecting a pc wireless access point that is authenticated by the radius server, im keep having this error "the certificate chain was issued by an authority that is not approved." do I need to set a certificate on the pc?

  Hello

  1. What is the version of the operating system that you are using?

  2. What is the exact full error message?

  If you use Windows 7 follow the link below:

  http://Windows.Microsoft.com/en-us/Windows7/view-or-manage-your-certificates

  http://Windows.Microsoft.com/en-us/Windows7/certificates-frequently-asked-questions

  You can also contact your ISP for more information.

  Hope the above information is helpful.

• Cannot enable authentication for 802. 1 x

  Original title: I can't change the properties on my wireless adapter to get the authentication of 802. 1 x. I get the error message.

  I get an error message when I right click on my wireless connection. I want to access authentication of 802. 1 x. need help, please.

  You see the error of not being able to find a certificate because you select 802.1 x.

  For a home wireless network, you don't want the box "Enable IEEE 802. 1 x authentication for this network"to check.

  What was the problem that you entered in the Properties dialog box of your first wireless adapter?  Normally, see you the list of available wireless networks, select one, click Connect and enter the password when you are prompted.

  I suggest that return you to the "Wireless networks" tab of the properties of the wireless adapter dialog box (it should look like this) and "Delete" all entries in the list of "Favorite networks."  Then go to list "View wireless networks" and connect from there.

  In addition, the foregoing assumes that you use Windows to configure your wireless network card (see the checkmark in the screenshot linked above).  If you use another utility - that came with your computer or your wireless adapter - you should disable that and activate windows (using the checkbox) or read the guide of the user for the utility to determine how to set up your wireless security.

• AIR-AP-1231 for guest access

  I have an obligation to provide wireless access to a device group. IPhones/netbooks etc. I have an ADSL wired connection and an AIR-AP-1231.

  I've connected the AIR-AP-1231 to the ADSL router and have obtained an IP address and got on the management page but I can't get the wireless network to be seen.

  I also need to restrict access to only specific MAC addresses. Longer term I want to ride more AP and connect them with a controller.

  I need to find a starting base guide and want to know if the model AP-1231 is suitabel for this role, or should I be looking at using a router Wireless Linksys standard?

  You have a setting on the vlan 1 under your d0 encryption interface. This is the beginning of a solution of WPA, but you need more under the SSID config:

  Cisco dot11ssid

  Authentic-version2 wpa key management

  WPA - psk ascii MySuperSecretKey

  For the work of MAC filtering, use the following example. Substiture in appropriate mac addresses for the x; 0 leave unchanged.

  access-list 700 allow xxxx.xxxx.xxxx 0000.0000.0000

  access-list 700 allow xxxx.xxxx.xxxx 0000.0000.0000

  access-list 700 allow xxxx.xxxx.xxxx 0000.0000.0000

  dot11 association-list mac 700

• Cannot connect by Satellite L300 wireless access point

  I have a new laptop L300 & I can't connect to the laptop to my wireless access point. I have an another mobile E-sytems with the same hardware Realtek RTL8187B & it connects without problems.

  The machine has the free two month Mcafee subscription & I have disabled all the protection incase that was causing the problem. I updated the driver for the wireless card & the bios on the Toshiba site, but nothing is.

  Can someone shed light on this problem because the laptop is only two weeks old?

  Thank you...

  Hello

  To connect the laptop to the WLan, it must ensure that everything is enabled and configured correctly.
  You should check these points:

  -activated the WLan with the WLan switch and the FN + F8
  -don t use any 3rd party config tools WLan if you use the WLan configuration options own Vista
  -for the first test WLan disable the security settings of the Wlan router
  -configure settings to laptop as good SSID and search for your wireless local area network
  -After that the laptop is connected to the WLan router, you can turn back the security settings (encryption, mac address filtering, firewall, etc.)

  Welcome them

• Card wireless INTEL PRO 2200 BG - don't find any wireless access point

  I just try to run internet with the internal PRO INTEL BG 2200 wireless card.
  The driver version is just updated to 9.0.4.39. The problem is, I can't find any wireless access point.

  I also use a D-Link card, with this card, I found the available access points. What could be the problem with the INTEL PRO card. I'm sitting right next to the router/hub.

  Also, I thought that I might need to activate the wireless with additional keys Fn function, but they do not work, I guess. Maybe I need a driver for this tool also. Do anyone know where I can find drivers to use the Fn keys?

  My system:
  TOSHIBA Tecra
  WINDOWS XP (SP 3)

  See also: The INTEL internet LAN works.

  > What could be the problem with the INTEL PRO card. I'm sitting right next to the router/hub.

  For me, it seems that the WiFi network is not enabled.
  Usually, you need to activate the WLan switch which is placed on the side of the laptop. Then, you'd see an active WLan led.
  If you n t see the light, then the WiFi network has not been activated.

  In addition, choose the WLAN using FN + F8!
  You can also activate the Wlan in Device Manager-> card Wlan-> properties-> Advanced tab.

  Good bye

• Set up the wireless access point, but the wireless devices are unable to get ip address

  Hi, I wanted to put my D7000 as router AP. My main router is Sagemcom F@st 3864 by Optus ISP (Australia).

  First of all, I put the D7000 in Bridge mode I did these steps:

  1. replace the IP LAN 192.168.0.100

  2 disable DHCP

  3. connect the LAN port to the main router Lan port

  Internet connection wired and wireless on the same device but other wireless devices has failed

  To remedy this, I made another choice, allowing point-to-point wireless access in the advanced settings of the D7000. I followed the instructions from this link

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24104/~/how-do-i-change-my-Nighthawk-router-to-AP-mode...

  I put dynamiccaly = wireless internet cable success but peripheral does not have an ip address

  No idea how to fix wireless? I'm not very experienced

  Thank you!

  I just fixed it just now. For AP mode, connect the LAN port of the main router to the WAN port on the D7000 (not LAN to LAN). I wish I thought to it much sooner.

• Issues with Dell desktop computer wireless and D-Link wireless network card. Only able to get wireless access by checking "Use Windows to configure my wireless network". This kind of file sharing impossible.

  original title: can't see the computer on wireless internet!

  I hope that's not too much detail, but I would like that the sequence of events to be clear...

  I have a Dell desktop computer that's probably six or seven years now.  It did not come with a wireless card, so I bought a DLink router and combo card wireless, install both with the DLink software.  It works beautifully.

  Later, we through my rep AT & T DSL, I got a Motorola modem/router with wireless capabilities.  I had plugged directly on my computer Dell desktop and moved to a Dell laptop DLink wireless receiver.  No problems.

  The Dell laptop is dead and the DLink receiver has not been used for a long time.  Family of my daughter moved to our place, and I have connected his desktop computers and laptop to wireless internet, using the Windows Connection Wizard.  Still no problem.

  I got a new ASUS laptop, I also linked using the Windows Wizard.  STILL no problem.

  Now, here's the problem comes.  I moved the Dell desktop computer, connected the DLink wireless receiver to it and I am able to get wireless access ONLY when I go into the properties of PC, click the wireless networks tab and check the "use Windows to configure my wireless network" box.  Then I can connect correctly, but I don't see this computer on my wireless network.  Bad luck... because I want to be able to access share files.  When I try to connect using different assistants of Windows, I get a message to the effect that, if I used another software to connect to the program, I can't use the Windows Wizard.

  So, what can I do to remove the original configuration of DLink completely and to connect to my wireless network using the wizards in Windows?  I uninstalled the software of DLink, but it seems to have no effect at all.

  BTW, Dell desktop computer is running XP, office computer of my daughter is running VISTA, and two laptops are equipped with Windows 7.  I can see all the computers on the network with the exception of the original Dell desktop computer wireless.

  Any help would be appreciated!

  Hi Joe and DonnaLoth,

  The network will have to be changed to allow the computer Windows XP join a workgroup.

  How to change a computer name, join a domain, and add a computer description in Windows XP or Windows Server 2003

  You can also read the following article.

  Networking of computers running different versions of Windows