Autonomous AP's web authentication

Similar Questions

• Independent WAP Web authentication?

  Is it possible to do the redirection of web authentication using 1131 s independent or that the function is available with WLAN controllers?

  Hello

  Authentication on the Web is only a solution for a unified environment (WLC). Autonomous aPs cannot perform this function.

  -Patrick Croak

  TAC wireless

• Web authentication Catalyst 2960

  Hello

  I am trying to configure Web authentication relief on a catalyst 2960 switch. The goal is to authenticate customers via web authentication that are consistent (the part of 802. 1 x works fine) not 802. 1 x and allow them access to the network. The problem is that the web authentication seems to fail.

  The equipment about my question: switch catalyst 2960 (version: 122 - 37.SE) and a FreeRadius.

  Here's what happens:

  The authentication window will appear in my browser and the access request is sent to the RADIUS.

  The term RADIUS replies with an Access-Accept. Debugging running on the switch show that all this information is coming properly authentication and switch outputs debug a 'status = PASS' and permission to debug outputs a 'status = PASS_ADD'. Despite this the browser on the client generates a message "authentication failure".

  I have read the manual and the Cisco attribute value pairs are mentioned: ' priv-lvl = 15' and «proxyacl...»» ». They are required to make it work? Given that I'm not setting up any authentication switch connection via RADIUS.

  Any suggestions?

  Thanks in advance

  Yes, they are mandatory.

  If priv-lvl = 15 is not returned to the switch, the user will see? Authentication failed? and the access list will not apply. If the source in the statements of proxyacl field is not? everything? or there are other errors of syntax, the user will see? Successful authentication? but the access list will not apply and the user will be denied access to the network.

  Not sure about the configuration of specific FreeRADIUS, but you need to set up the? [026\009\001] Cisco av pair VSA. It should look like:

  Priv-lvl = 15

  proxyacl #10 = ip permit a whole

  Let me know if this lets you squared

• Bundle of Web authentication on a WLAN controller integrated Catalyst 3750

  We have set up a wifi zone based on a few 1131AG access points and a few Cisco 3750 integrated WLAN controllers. We are now trying to use web authentication for our comments area. No problem by defining a WLAN of COMMENTS and the associated VLAN. We have also managed to download a custom controller authentication web page.

  However, when I try to display the custom page, both controllers of show me the internal default page (preview and during the phase of actual authentication).

  Global web authentication settings are the following: Security--> Auth Web--> Web Login Page--> custom (downloaded).

  On the controller software version is 4.2.112.0, and the page is an HTML page.

  Reveal any help be appreciated.

  Kind regards

  Sonia

  What you need to do is set internally (by default) and hit apply, then play again to custom and click on apply. You can still see the defaul if you use the preview, but if you associate the SSID and open your web browser, you should get the webauth page. I hope this helps.

• WLC (foreign-anchor), problem with external web authentication-> ISE

  Hello guys

  I am designing a platform for a network of comments, which must be isolated from the LAN, the following facilities:

  • ISE 1.2 (SNS-3415-K9 Cisco)
  • WLC 7.0.230.0 (Cisco 5508 controller)---> foreign wlc
  • WLC 7.0.230.0 (Cisco 5508 controller)---> wlc anchor.

  The PAES tunnel between wlc is successfully completed.

  The wireless client gets the IP address of the anchor wlc (DHCP server).

  Test 1:

  I have set up the ANCHOR WLC with local web authentication (internal), the wireless client is authenticated by WLC and successfully navigate.

  Test 2:

  Configure the authentication web external anchor (ISE) WLC. Configure a user to the portal comments ISE.

  The wireless client gets the IP address of the anchor wlc (DHCP server), attempting to engage not display comments portal.

  Debugging a wireless client, try to connect to the guest network is attached.

  That's right... they have a version of code required minimum supported for this.

  Thank you

  Scott

  Help others using the system of rating and marking answers questions like "answered."

• Assignment of VLAN dynamic of the Web authentication

  In a firmware WLC 4402 v.5.2.157 is possible to assign users to one VLAN dynamic based on the RADIUS response received from ACS?

  Yes and no. You can do for a WLAN 802.1 x internal, that the customer does not get an IP address, until they have completed the authentication process. To do this, you use 64/65/81, 64 802, 65 VLAN and to 81 use the name of the interface, not the number VLAN. you will also need to make sure you have AAA Overrided activated under the WLAN.

  If, as is said for Web authentication, the answer is no. The client has an IP address before being validated by the AAA server.

  HTH,

  Steve

• Web authentication passthrough with input from the e-mail

  Is it possible to use a custom login.html page when web auth/passthrough is used with the input of the email? I have a requirement to have just the users to register with an e-mail address and I need to provide a custom page.

  I receive custom login pages, but I can't figure out how to make a customized with only e-mail login.html page entry.

  Any help is appreciated.

  Thank you

  Kurt

  You should also check wireless downloads. In the area where you can find the code of the controller to download, you can also find a 'Wireless LAN Controller Web authentication Bundle' containing several samples of html, including e-mail data.

  This link might work, maybe not:

  http://Tools.Cisco.com/support/downloads/go/InterfaceModuleSWT.x?mdfid=279911269&mdfLevel=model&treeName=wireless&modelname=Cisco%204404%20Wireless%20LAN%20Controller&treeMdfId=278875243

• Ie9 beta does not have the web authentication

  Hello

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : SimSun ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : Arial ; mso-bidi-theme-font : minor-bidi ;}

  I have a question:

  We had a user who defines the Cisco web-authentuicated WiFi SSID as network Public in the firewall of Windows 7 and when he tried to connect to WiFi, it appears a troubleshooting page and said: "Connection to Web pages are currently redirected to a different Web page."  It uses IE9 beta.  Most likely the browser it's a MiTM attack.

  Apart from declaring (SSID) network as a private network secure, y at - there another solution?

  Our goal is to get the users (which come from major conferences) on the network without them having to change a lot of things on their laptops. They would be naturally defined as a Public network.

  Thank you

  Suman

  The concept of web authentication IS a man in the Middle somehow attack... And IE9 is not a browser supported either.

  I don't know what makes IE cause this error exactly well. You have a DNS host name and the certificate on your webauth?

  Nicolas

• The web authentication.

  I want to configure a switch for IEEE 802 authentication port. 1 x with web authentication as a means of rescue.

  Can anyone provide an example of a valid configuration?

  Only web authentication does not work!

  Switch #sh run

  Building configuration...

  Current configuration: 3012 bytes

  !

  version 12.2

  no service button

  horodateurs service debug uptime

  Log service timestamps uptime

  no password encryption service

  !

  Switch host name

  !

  !

  AAA new-model

  Group AAA authentication login default RADIUS

  connection of line-con AAA authentication, no

  Group AAA dot1x default authentication RADIUS

  Group AAA authorization auth-proxy default RADIUS

  !

  AAA - the id of the joint session

  switch 1 supply ws-c3750 - 48P

  mtu 1500 routing system

  IP subnet zero

  IP - cisco.com domain name

  property intellectual admission name rule1 http proxy

  !

  !

  !

  !

  control-dot1x system-auth

  !

  !

  !

  !

  !

  !

  Profile relief aid

  IP access-group Policy1 in

  rule1 admission IP

  !

  pvst spanning-tree mode

  spanning tree extend id-system

  !

  internal allocation policy of VLAN ascendant

  !

  !

  !

  !

  interface FastEthernet1/0/1

  switchport access vlan 142

  switchport mode access

  !

  interface FastEthernet1/0/47

  switchport access vlan 142

  switchport mode access

  dot1x EAP authenticator

  self control-port dot1x

  relief aid dot1x

  !

  interface Vlan1

  no ip address

  Shutdown

  !

  interface Vlan142

  IP 10.1.254.1 255.255.255.0

  !

  IP classless

  !

  peche1 extended IP access list

  allow udp any any eq bootps

  deny ip any any newspaper

  !

  Server RADIUS attribute 8 include-in-access-req

  secret key of acct-port 1645 auth-10.1.254.187 - RADIUS server host port 1646

  Server RADIUS ports source-1645-1646

  RADIUS vsa server send authentication

  !

  control plan

  !

  !

  Line con 0

  line vty 5 15

  !

  end

  Try adding this:

  analysis of IP device

  In addition, if you want your users to web-auth to use DNS to resolve URLS, you probably want to add something like this to Policy1:

  allow udp any any eq field

  Don't forget that you need to wait until the 802. 1 X times out (90 seconds by default) for Web-Auth to kick.

  Shelly

• Web authentication WISN and COMMENTS

  I have a WISN and we use open web Cisco

  authentication with a user's e-mail address.

  When executing this CLI command:

  > config network secureweb disable

  > save config

  > the system

  This will make the web authentication come HTTP instead of HTTPS?

  This command is for managing the unit.

  However it used to be a workaround when you disable HTTPS and SSH and you restart the WLC web authentication will be displayed as http and not https.

  Let me know if it works for you

• Web authentication

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  The team wishes

  If I have web based authentication passthrough, you use an external web server, so in passthrough mode the web server should communicate with the WLC for the client credentials?

  Please can anyone provide an example of a web page for passthrough where the customer simply click on I ACCEPT, then he is redirected to the internet

  Thank you

  for passthrough, it does not require authentication of the.  There are always attributes that are passed to the WLC who tell us that the customer has "passed."

  For an example of webauth page, this can be downloaded from www.cisco.com in the same area you download the code for the WLC

• Web authentication with RSA SecureID on a Cisco Switch

  Hello

  I recently searched by linking in our Cisco Switch of GB 2960 S with RSA SecureID via Radius

  I already managed to tie in to ssh access

  but I failed to make it work for http / web access to the switch

  I think it's because we use 'single use' maximum security with RSA SecureID tokens

  the web interface tries to authenticate several times against the Radius server RSA SecureID part

  (agreement on the first authentication, but every time after that he's going to want a different code in token)

  I was wondering if anyone knew a way around this? (if there is a way to get the right switch authenticate once instead of multiple times the radius server)

  FYI, the switch is a WS-C2960S-24TS-L with IOS 15.0 (1) SE2

  Hello Chris,

  You can test the following configuration?

  AAA webtac_grp radius server group

  Server

  expiration of cache 1

  authorization cache profile httpauth

  hiding authentication profile httpauth

  !

  AAA authentication login httpauth cache webtac_grp group webtac_grp

  AAA authorization exec httpauth cache webtac_grp group webtac_grp

  AAA authorization network httpauth cache webtac_grp group webtac_grp

  AAA cache profile httpauth

  all the

  IP http server

  IP http authentication aaa - authentication of the connection httpauth

  IP http authentication aaa exec-authorization httpauth

  RADIUS server host key *.

  I know for sure the above configuration works when you use GANYMEDE + instead of RADIUS in order to avoid multiple guests due to the authentication of JAVA Applets to access the GUI of the IOS. I him have not tested against RSA acting as an authentication server.

  NOTE: As "aaa authorization exec" is configured the RSA should send Service-Type attribute with administrative value for it to work as expected.

  If this was helpful please note.

  Kind regards.

• Custom Web-authentication application

  I am trying to create an authentication for a web application. Is this possible? I find examples of DB applications.
  
  I did the following and hit bad...
  
  

  create table vl_emp_master (empid number,pwd varchar2(100));
  
  insert into vl_emp_master (empid,pwd) values (4781,'1234');
  
  insert into vl_emp_master (empid,pwd) values (4787,'1234');

  created a package
  

  create or replace package pkg_tr_usr as
   function tr_check_usr(p_uname varchar2,p_pwd varchar2) return boolean;
  end;
  
  CREATE OR REPLACE package body pkg_tr_usr as 
  function tr_check_usr(p_uname in varchar2,p_pwd varchar2)return boolean is
  v_ret integer :=0;
  begin
  
  select 1 into v_ret from vl_emp_master where empid=to_number(p_uname) and pwd=p_pwd and rownum=1;
  
  return (v_ret=1);
  
  exception
  when no_data_found then
  v_ret:=0;
  return (v_ret=0);
  end tr_check_usr;
  end;

  tested like this...
  
  

  declare
  bres boolean :=false;
  begin
  
  bres:= pkg_tr_usr.tr_check_usr('4781','1234');
  
  if bres=false then
  dbms_output.put_line('1');
  else
  dbms_output.put_line('0');
  end if;
  end;

  and made the following changes in the authentication of the process...
  
  In "Application-> properties"-> "Authentication service" authentication-> return pkg_tr_usr.tr_check_usr;
  
  but not able to connect, do following error...
  

  ORA-06550: line 2, column 8: PLS-00306: wrong number or types of arguments in call to 'TR_CHECK_USR' ORA-06550: line 2, column 1: PL/SQL: Statement ignored

  Thank you
  HESH

  OK, I'm going to presume that apex is installed in the same pattern as your 'vl_emp_master' table.

  First of all you must manually create the admin user. All users of the application websheet are stored in APEX$ _ACL table. So we insert all the 4000 in there automatically.

  APEX$ _ACL (ID, WS_APP_ID, USERNAME, PRIV, CREATED_ON, CREATED_BY, UPDATED_ON, UPDATED_BY)

  We want to insert:
  WS_APP_ID is your application id (for tests, I will assume it is 100)
  Username - empid of your table 'vl_emp_master '.
  PRIV - an - admin, R - drive I think and there is a letter more I don't remember
  CREATED_ON, UPDATED_ON, you can put here today
  CREATED_BY, UPDATED_BY which is the name of your workspace (to test, I'll assume it's "Hesh")

  OK, so open your sqldeveloper, sqlworkshop or sqlplus any and type:

  SELECT * FROM APEX$ _ACL, now you should just see your admin user.

  OK now we will insert all 4,000 of them.

  INSERT INTO APEX$_ACL (WS_APP_ID, USERNAME, PRIV, CREATED_ON, CREATED_BY, UPDATED_ON, UPDATED_BY)
  SELECT 100, empid, 'R', '03.05.2012', 'Hesh', '03.05.2012', 'Hesh'
  FROM vl_emp_master
  

  Published by: 910011 on 3 may 2012 14:10

• HP Pavilion g7: error code 0 x 80070057 web authentication

  When I try to access my web references to retrieve passwords I get an error code 0 x 80070057 #, says the parameter is incorrect.

  Hello @italli66,

  Thanks for the quick response!

  The video is for Windows 7, but you should be able to try the process for Windows 10.  Please let me know if it is your problem.

  Kind regards!

• local web authentication fails

  Hello experts!

  I have problems performing clients to authenticate locally on a controller 2106 with ios v.4.1.171.0.

  do I need a radius server must be able to get local auth.

  also the auth login page does not automatically appear when I open a browser and type www.cisco.com or any other url.

  I have to type in vip 1.1.1.1 to be able to set up the connection on the page.

  This is how it is supposed to be for this particular code.

  Thanks for any input... really appreciate it.

  It seems that you have a configuration problem on the wlc. If you can access the web before enabling webauth then you should have no problem getting web page... unless you have a proxy? If you enter 1.1.1.1 and get the webauth page, then it looks that dns does not work or perhaps your home page is a secure https page. Try google.com or something like that.