Availability of 3G module?

Similar Questions

• Availability of encryption modules?

  I currently use encryption support AES of RIM in my application, but I fear that libraries may not be on devices of all users, due to the version of the OS, controls the export or other things.  According to the developer documentation (http://www.blackberry.com/developers/docs/4.5.0api/net/rim/device/api/crypto/doc-files/CryptoAlgorit...):

  "not all algorithms supported are loaded onto the aircraft in its default configuration. For best performance, your handheld can be optimized to include only a minimal set of cryptographic features. Conversely, to increase security, users who wish to use PGP, S/MIME and TLS must load a larger cryptographic file on the device. "

  How this loading take place?  According to the table on the page, AES is provided in net_rim_crypto1.cod, but how is who is responsible?  It just seems to work in my tests, but I do not know if I have anything that to do so, or if it will work on another device.  I include it somehow, and if so will it be affected by export controls?

  In general, I'm looking for a method of encryption BB available worldwide.  The libraries of the RIM are convenient, and I would like some advice I know if I should continue to use.

  Thank you
  Jim

  Just for info... I use the native implementation of the AES RIM strongly and in the last 3 years, I never ran across a pocket computer that did not have the proper libraries.  The chances of a person with disabled AES are so low that it isn't worth it to worry about the.

• HA for firepower Modules END ASA 5585 x - SSP 40

  Hello

  I have a question.

  With two Cisco 5585 - X PHC-40 in multi-contexte mode. Both the ASA firewalls are already configured for failover for high availability.  What is the configuration of the firepower Modules get high availability if a module of firepower in one of the ASA falls down.

  Thank you

  Ravi

  Failover of the SAA will happen, because with the default service configuration module is monitored as part of the failover condition.

  Which can be changed via "no monitor-service-interface module" SAA - the command turns off service module monitoring and, if the module fails, it will not trigger the failover.

• Cannot delete the system Module

  My application consists of 2 modules. A system with autostart module and a module "classic."  I never had no problems update of the modules with the desktop so far Manager. The module system refuses to update and it is impossible to remove it. I'm stuck with an older version. If I do an uninstall via Desktop Manager, only the non-system module is removed. Try to remove the module from the system via the Options, device, application management does not work. The module is there, but a "Delete" option is not available for this module.

  Try an installation via Desktop Manager it reports as an "update", but the sysm module is not updated

  Version of the platform on my torch is 6.6.0.236.  The software version is 6.0.0.668 and my version of Desktop Manager 6.0 Bundle 2949.

  I'm completely stuck! Can not update the module of the system. It is a new problem. I have this Setup developed for several years and never had a problem like this before. It's extremely frustrating

  JavaLoader is a command line tool, it comes with the JDE plugin or eclipse in eclipse you can find it at plugins\net.rim.ejde\vmTools (where the sigtool is located as well).

  use to remove a cod file could be:
  JavaLoader u f clear codfile.cod

  check -? other solutions, this is a very handy tool to make screenshots, extract log files, load or delete files, etc.

• Construction of a Module separated from ATG

  Hi all
  
  Please suggest a few solutions for the scenario below.
  
  I have some components (say * "Component A and component B" *) developed within a module of the ATG (say * "Module A" *). I want to separate these components and create a separate ear/war. Which I can deploy independently.
  
  But the components A and B is reffering other components in this module. In this case, which will be the best solution to go forward.
  
  
  My goal is to separate the components developed for specific features and by deploying separately as an independent module.
  
  Kind regards
  DIABETIC KETOACIDOSIS

  When you define ATG-required: CommonModule then all resources defined in CommmonModule MANIFEST. MF file will be available to your module.
  So all the classes defined in CommonModule that is defined in the CommonModule ATG-ClassPath are available for your module.

  Peace
  Shaik

• eTRM for all modules of the RCMP

  Hello
  
  I need to know where are the eTRM available for all modules of the RCMP. I tried http://etrm.oracle.com, but there is no information under "RCMP".
  It's really important.
  
  Thank you!

  Hello

  Please note that eTRM is not available for the modules of the RCMP.
  If you need materials to understand the Architecture of Tehnical in consequence of the RCMP, please contact your sales representative who will be able to provide it.

  If you need Documentation, CCRG, it is available at:
  http://www.Oracle.com/technology/documentation/logicalapps.html

  I hope this helps.

  Kind regards
  Eric

  Published by: Eric Desai on April 27, 2010 17:34

• Satellite A60 and 512 MB RAM

  Hi, I have a Toshiba refurbished Satellite, that's why 512 MB of RAM. When I read the manual, it ok it s know put in 1530 MB more too end up to 2 GB of memory ram so-dim.
  Don t get it. went to a store, to say that an A60 has memory, on the motherboard, it s only a single slot.
  ??? Maybe I missunderstod, but who can tell me to move this, Don t think that there is no 1.5 GB so-dimm.
  The 3.06 Ghz processor.
  HUF
  Suzing

  Hello

  I found information that Satellite A60 has 512 MB of RAM onboard and a single RAM slot is available. The module of RAM to use this device must be PC2100 DDR - RAM and maximum memory that your device can handle with 1536 MB.

  Recommended by Toshiba RAM modules are:
  256 MB (PA3311U - 1 M 25)
  512 MB (PA3312U - 1 M 51)
  1024MB (PA3313U-1M1G)

  Good bye

• New video card and memory for my laptop (1410-604)

  Hello

  I think of a new video card and an extra memory...
  What possibilities I have to upgrade my laptop (Satellite 1410-604).

  I checked my computer technical description:
  I think I can add an extra 256 MB SDRAM. But what video card?

  Koen

  Hello guys

  It s not possible to update the graphics card. You can't compare the desktop with a laptop PC. The graphics card on the laptop is a small chip that attaches to the motherboard.

  On the upgrade memory: you can upgrade the memory maximum. 512 MB (2x256MB). There are 2 slots available and these modules of memory are supported:
  PC2100 128 MB (PA3126U - 1 M 12)
  PC2100 256 MB (PA3127U - 1 M 25)

• DDR3 DDR3L vs for mid-2012 MacBook Pro 15 inch

  On crucial.com, I chose my system I, mid-2012 MacBook Pro 15 inches. I want to move to 8 GB of ram, but I want to know if their DDR3L will work. On their site it says DDR3 is 1.35 volts and the DDR3L is 1.35 volts as well. They are both the same speed, 1600. What is the difference between the two and the DDR3L will work? My current ram is DDR3 4 GB and the speed is 1600. Thank you.

  DDR3:

  CT4999407 http://www.crucial.com/USA/en/MacBook-Pro-%2813-inch-and-15-inch%2C-Mid-2012%29/

  DDR3L:

  CT3373649 http://www.crucial.com/USA/en/MacBook-Pro-%2813-inch-and-15-inch%2C-Mid-2012%29/

  On the site of crucial, characteristics of RAM that you have access to:

  "Standard DDR3 modules help Mac systems reached speeds up to 1600 MT/s.. For new systems, Mac, DDR3L modules are available. These modules offer speeds from 1866 MT/s and use 10% less energy to improve energy efficiency. "

• Satellite A100 does not start after the BIOS update

  Hello

  I downloaded the update to the bios toshiba A100 PSAA8 on the toshiba site and applied using the procedure of updating the bios from windows XP MSE. Restart after the start of the update stopped at the toshiba start screen.

  At startup the screen by pressing ESC watch text mode. The message indicated it confirms the update of the bios version. POST messages are:

  _________________________
  Genuine Intel CPU
  No TPM or TPM has problem
  1015 M system RAM passed

  Press to enter in SETUP
  _________________________

  Pressing F2 just clears the last message in line and then no change is found.

  The laptop comes with windows XP media center edition. I don't know why the TPM secure is enabled. It is possible that toshiba is available with the module of TPM enabled in bios updates that logbook. If this is the case, they must clearly identified as 'not applicable' upgrade for machines that are not relevant.

  I found similar messages around the forum without convincing answer.

  Is it possible to fix this without sending? Even if it turns out to be affordable, it make much sense to pay for the problems caused by toshiba.

  Hello

  Please don t blame someone for you mistakes ;)
  As far as I know that only a few sets of laptops come with TPM.
  If you want to do an update of the BIOS on the models at TPM, you will need to contact the ASP!

  Looks like you used a bad BIOS or bad BIOS update procedure.

  The Toshiba page a BISO update the documentation that describes how to upgrade the BIOS on each series laptop!
  You will find on the page of the Toshiba driver compatible BIOS and information over a large number of details!

  > Is it possible to fix this without sending
  Don t think so, and therefore, you will need to contact the Asp help!

  Good luck

• Can what parts I replace in my Satellite A50 - 106

  Hi guys.

  I have an idea to replace a few parts in my A50-106.

  And here my question. What can replace :), maybe processor or else HW?

  Thx for the answer.

  You can replace the HARD drive with more capacity and RAM module. This notebook can handle with max 1 GB of RAM. Two memory locations are available. Compatible modules are:
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  I'm not 100% sure but I believe you can also swap ODD (optical disc drive) with best. Check it please users manuals. No doubt you will find a list of all compatible ratings.

  Good luck!

• Measurment LVDT DC with CompactDAQ

  Hello

  I am currently working with reading as a result of an LVDT for a project that the present model is the DC LVDT Omega LD620-25

  According to the data sheet's model requires a voltage of 10-30 v and a maximum current of 25ma

  http://www.Omega.com/pptst/LD620.html

  with regard to the available data acquisition modules: the NI 9237 and the 9220 OR by using a module compactDAQ

  as the NI9237 has an internal output of 150mW obtained maximum current is 15ma, simply use?

  the 9220 OR will be used for the acquisition of data but provides no port of excitement!

  as for the solution another I thought using an AC adapter / CC of normal 12Vdc 100ma with a variable pot or a circuit voltage divider to provide the necessary tension

  but I have several concerns with respect to the Earth circuit. in this system, I will have two independent reasons!

  What will be the best solution to connect the LVDT module to the 9220 OR and provide a source of external excitation?

  Thank you

  Hello ghattas.ak

  Consider the NI 9218. It can provide 12V exictation to ~ 50 mA per channel and read 5 or output 10V DC LVDT. To use this excitement 12V, 9 - 30V power supply must be connected at the Vsup pins. As you said, you can also use the 9220 OR with external excitation. The NI 9237 measuring range of +/-25 mV/V does not cover the 5 or 10 v output sensor you.

  See you soon,.

  Izzy O.

  Product Support Engineer

  National Instruments

  NI.com/support

• Is PCI6513 supports the replay?

  Is PCI6513 supports playback of channels values?

  How will I know if the collating of channel is available for some module?

  Hi Jane,

  The 6513 does not support rear reading. If you want to check what you write for digital ports, I would just wire in an analog or digital input. Some of the e/s high-speed digital boards (654 x, 655 x 656 x) can support what you are looking for. What is your application?

  Sean

• Problems installing the 4-DVD set 2013

  I am trying to install LabVIEW 2013, with the real-time Module, DAQmx and a few toolboxes Vision module, using a Kit of Distribution 4 - DVD.  I use the feature very attractive who appeared in the 2012 LabVIEW Distribution Kit - when you put it in the DVD - 1, it shows you all the available Toolkits and Modules.  You can check as many as you need, and he moved between them, apparently to 'DVD-order' (i.e. DVD-1, then DVD-2, then 3-DVD, then DVD - 4).

  The problem is that when you finish and reboot your PC, the Services NOR critics (who could have been present before installation) are missing, leading to a behavior very interesting, one-power-say "buggy".

  According to engineers of NOR, I'm not the only one who saw the specific results after installing LabVIEW 2013.  In my case, I installed LabVIEW 2013 on 4 PC, all with at least 2012 present LabVIEW on a previous installation (and work fine before installing LabVIEW 2013).  A PC continued to operate properly after installation of 2013, but the other three were absent OR Services.

  After some tests, I realized how to install LabVIEW 2013 to avoid losing services - simply go back to recommended practices OR installation, I used in most earlier versions of LabVIEW.  Instead of taking the 'shortened' to specify all the packages to install both, one-at-a-time installation packages, in the following order (at least, this prescription "worked for me") - LabVIEW, the Time Module, any Module, all Toolkits, DAQmx, and device drivers.  After that each piece is installed, allows the system to reboot if it is said that he needs to do.

  Watching the process carefully, I see that some installation steps "kill" LabVIEW services, but the subsequent reboot brings back them (and sometimes add new services).  I suspect that the method of the "all-at-once", which has only a single reboot at the end, somehow fails to resurrect killed service, leaving a paralyzed installation.

  Making an installation package is both slower, involves the exchange of DVD much more, but seems to work.  I sent my comments to OR, and they are working on the issue.

  Bob Schor

  OR just released update 1 for 2013 LabVIEW that solves the problem by doing an 'All-in-one' of 2013 installation, according to me.  In particular, he seems to reinstall the Service Locator Service.  I'm largely 'patched manually' most of my systems, but I think I've seen one of my non-working fixed PC.

• 9401 serving counter in cRIO 9022

  Hi all

  I use cRIO-9022 and 9401 is one of the modules of him. I want to use 9401 as counter in the FPGA VI. Is this possible? As the specialized digital Configuration option is not available when the module is moved to the target FPGA.

  Shrinivas

  Yes, you can, and many of us do on a regular basis.

  Good read from this link to help you get started.