Basis of LabVIEW Development with Compact RIO device software

Similar Questions

• touchscreen compact Rio

  Hello world!

  I'm developing an application to control a cooler with Labview 2012 and Compact RIO. I would like to create a group of GUI to visualize data and a basic control.

  However, I would like to use a touchscreen to third party (not OR). Purchase the Labview Touch Panel module can I do?

  My question is: if it's just a screen and not a PC, simply by connecting to the RIO Compact RS232 port and launch of real-time application,

  It will allow me to control the VI?

  Thank you!

  I don't see why not.  You need to just make a protocol of good communications between your cRIO and computers touch screen.  I find a network stream to work very well.

• Charging Curve 8900 Smartphones blackBerry device software

  Hi I have a problem with my Blackberry device software, how to remove and re intsal software on my Curve 8900?

  Manual device OS upgrade instructions:

  1. start by searching for your operator and the system operating file that you want to use.

  http://NA.BlackBerry.com/eng/support/downloads/download_sites.jsp

  2. make a backup of your device first, using Desktop Manager > backup. Close at the end Office Manager and disconnect it from BlackBerry. Get DM here http://us.blackberry.com/apps-software/desktop/

  3. download the OS files to the PC then install on the PC by running (double click) the downloaded file.

  4. go into c:\program files Research in motion\apploader and delete the file named "vendor.xml."

  5. This step is not necessary unless there is a problem on the next steps. Use BBSAK from BBSAK.org and wipe the device (after doing a full backup), then after you get the 507 error (no OS installed) then proceed to step 6

  6 remove the internet connection for PC and reboot the PC.

  7. plug the BlackBerry and double-click on "Loader.exe." It is located in the same place as the above vendor.xml file was in.

  8. If you did step 5, restoration of the back upward. Follow this KB if necessary http://www.blackberry.com/btsc/KB10339

  Take advantage of the new operating system.

• Reading Configuration files using Labview RT in a Compact RIO

  Hello

  I am very new to Labview RT/Compact RIO development platform and happen to have a question. I will develop an application in Labview RT / FPGA that will make several simulations. However some these simulations can produce different results depending on the configuration settings. Our systems generally run in a Windows application, were there is a configuration (usually in XML format) file that the application reads and analyzes the given parameters. I was wondering if there is something similar, that I can do it, in which I have a configuration file that can be read before my Labview RT/FPGA application initialization, to change the simulation.

  Thank you

  Mario

  Hi Mario,.

  That's right, there are screws for the files .ini on real-time targets.

• Accidentally that hidden/removed the base Panel (the one with the shadows, made highlights, contrast, exposure) to develop module. I was clicking on the exposure slider when my mouse slipped and I clicked on something. How to do back panel?

  Accidentally that hidden/removed the base Panel (the one with the shadows, made highlights, contrast, exposure) to develop module. I was clicking on the exposure slider when my mouse slipped and I clicked on something. How to do back panel?

  Make a right-click on any other Panel name develop. In the menu that appears, put a check mark next to the base.

• Compact RIO NOR-9082 Configuration in MAX, cannot save

  Hello world

  I tried to implement a new cRIO the NOR-9082. Currently, I am able to see the cRIO under "Remote devices" in MAX configuration and view. However, the two errors that are produced:

  (1) when I try to change the setting as the host name and press 'save' a warning appears saying: "there was a problem, save the settings of the target. Make sure that your material is under tension and hat it is connected to the network. I have attached a picture below.

  (2) at the same time, when I try to install the software on the cRIO by double-clicking on 'software' and selecting "Add/Remove software" and run the Wizard "LabVIEW Real - Time Software", another error is displayed: "error: the disk hard n the remote system is complete or encountered an i/o error." I've also attached a picture below.

  The cRIO is lit with "DISABLE RT' toggled OFF. It is connected to the network via an Ethernet cable. This connection seems fine, however I look. (The connection of Ethernet port light flashes continuously activity indication etc..) It is the PC that is connected to the same network, I'm trying to interface with the cRIO. The cRIO displays the right IP address assigned through the network.

  My apologies if I have not provided enough information to solve this problem, but if someone might be able to explain why I could meet these two problems in these circumstances, assistance would be much appreciated. Thank you!

  It seems the main reason I got all these weird problems, it was because the compact RIO NI 9082 can come bundled with windows 7 and LabVIEW 2012 SP1 preinstalled and run as stand-alone computer so all I had to do was plug in a VGA to a screen and a mouse USB, keyboard and an eithernet for network connection cable and he started very well. Now, development and deployment happen locally on the cRIO. It was a little silly to me, so hope that helps someone!

  Kind regards

  Ago - Wei.

• Handshaking DMM with multiple switching devices - DAQmx error

  Hello.
  I am trying to create a loop of the handshake with DMM (PXI-4071), SWITCH (PXI-2569) and MUX (PXI-2575). The three instruments are in segment 2 chassis PXI-1045 (locations, 8, 9 and 10) and I use the ways of PXI trigger in the triggers of the route.
  I followed the article NOR 'Multimodule Scanning with National Instruments switches' - I modified the example NI SWITCH "niSwitchDMMSwitchHandshaking" to set up another SWITCH, but when I tried to run the example, I got an error:
  
  0xbffa6b9a - no lines recorded could be found between the device in the road. (screenshot pop up is in the attachment). It is the function of niSwitch_InitiateScan to the second switch that returned an error.

  PIX trigger change has no effect.
  I tried the CVI and LabVIEW examples with the same result.
  I even tried to use two 2575 MUXes - same result.

  Can someone tell me what I am doing wrong?

  Hi Pavel,

  I checked that the component that controls the routing of the TTL for the PXI is included in NOR-DMM 3.0.2 (latest version as of 06/14/2010).  NOR-DMM 3.0.1 contains an older version of the TTL routing code and will therefore place several comprehensive lines scanning advanced on the same trigger.

  Unfortunately, the component which controls TTL routing is one of the constituent elements of the software installed OR lower, and thus we do not expose it to the user.  For that to work, we would need to uninstall almost all the software components of NOR, which is a major undertaking.  Here's what I recommend instead:

  For now, we will Garland triggers one switch to another.  This will allow us to start development in OR-Switch; as soon as OR distributes a program, you simply change the triggers as they all point to the same TTL line.  This will allow switches to operate in parallel rather than in series, and the passage of the switch of your project can run faster.

  If we have to absolutely exploit the switches at the same time, I would recommend either uninstall all software of OR or get a machine with a fresh install of XP and then install not newer than 8.9.5, OR DMM 3.0.1 DAQmx software and NI - Switch3.8.

  As I mentioned earlier, NEITHER is aware of breaking backward compatibility and we are committed to reintroduce the old features in a future release of the pilot.

  Keep this thread bookmark and post back in a month or two and I'll let you know if we have any updates.

  Have a great day!

• New user of Lab-view and Compact RIO

  Hi I am new to Labview environment and cRIO. I have to design a CAN bus for electronic car. I've done a few tutorials on how to create a VI. If anyone knows where I'll start to be able to send and receive messages using CAN bus and Compact RIO in order to implement the actual data from sensors or actuators CAN message?

  Thank you

  Abdoulaye

  Start with the examples provided with LabVIEW.  To the title of the help, select «Find examples...» ».  When the finder example opens select 'hardware input and output-> Compact RIO-> Module e/s specific-> CAN' and try to start with the basic example of CAN.

• RIO devices

  Hi all

  Does anyone know of a way to view RIO devices currently installed in labview? I have a system that will use devices FlexRio 1 or 2 and I need to get this information in labview to allow to adapt the code.

  Currently, I can see the device in MAX under the section of RIO but don't know how to get this info in labview.

  Any help would be appreciated

  James

  Hi James,

  It is possible to detect devices NI FlexRIO help NI-VISA.  I have taken this knowledge base and tweaked a bit to generate a list of all the devices in RIO on my machine:

  

  Probably help some other NI-VISA properties that you can use, but the Description of the Interface property will return resource name, model number, slot number and serial number.

• NTP synchronization drop Linux Compact RIO

  Hello

  I followed this method of synchronization with NTP (https://decibel.ni.com/content/docs/DOC-39178) and it works most of the time, but sometimes, I lost the NTP synchronization and crio are about 7 s forward. (I get the problem with a 9035 and a 9068).

  When synchronization is no longer works, Pei ntpq command responds "connection refused".

  Does anyone have an idea about the problem?

  Thank you

  Hello Jacques,.

  Sorry, I wasn't very clear

  Before you add the ntp-utils, I lost the synchronization several times: sometimes after a few days, once, after more than 2 weeks, but also sometimes on startup, I was not able to sync

  Given that I have install ntp utils, 10 days earlier, on 5 compact rio, I run the of-p command ntpq every minute and I always get a response, then that means I never lost the NTP synchronization (or I lost it less than a minute). I will continue to monitor them, but it seems that ntp-utils has helped me as weel

  Concerning

  Kevin

• "VI a error 1002288.The full version of LabVIEW Development is necessary to correct the errors."

  Hello

  I had created an executable in LabVIEW 8.6 on a PC windows XP 32-bit. The application uses some screws of Vision. The executable is running in most of the PC except one. the PC is a windows 7 64 bit. I first got the error "Labview support 3 error code: could not load front". "" I fixed this by changing the settings of the source file in the application builder. Now I get the error message "VI a error 1002288.The full version of LabVIEW Development is necessary to correct the errors"and the exe displays a run button broken.»

  But if I build the exe in the same PC I get no error and it works very well. Moreover, I tested this exe in another PC with the same configuration, it works. I tried to reinstall labview in the PC, the problem persists.

  Hi Nitrox,

  There is no official adapter for LabVIEW 8.6 in Windows 7. See link below.

  www.ni.com/LabVIEW/OS-support/

  Upgrade to SP1 LV2009 should solve your problem. We had this problem with another client and update SP1 LV2009 solved his problem and should solve your problem too. If you have a problem after the update let me know.

  Kind regards

  Christophe P

  Technical sales engineer

  National Instruments

• stand alone compact rio

  Hi to everyone!

  I am a student of the University and for my thesis, I use a COMPACT RIO with neither 9205 and gps module, some measures aboard an eletric car, measures will be saved to a TDMS file in the RIO COMPACT by a stand alone configuration and without connection to a pc.

  The compact rio will begins with the car and it will go off with him also.
  So I have a question, how can I stop the VI within the CRIO before turning off the car?  or in TDMS data will be saved in the same way without close the VI within the CRIO before turning off the car?

  Thank you

  Hello antoniolc!

  There is no way of knowing inside CompactRIO, if the system will be shut down.

  You must use an external signal to find out when your car will be stopped.

  Or you can use a multiple TDMS file and like it, just the last TDMS file will be unreadable. But you can probably read all previous TDMS files.

  Best regards.

• Selection of Module e/s analog compact RIO

  Hi everyone, sorry if this is the wrong place to post, I couldn't see any analog IO section in the hardware section.

  I'm looking to acquire an analogue of module e/s for a compact RIO, but there are a few options, and I was wondering if there was any kind of guide to help me to choose the most appropriate module?

  Dawud,

  This will depend on especially what entries you want to read, but you must keep the following in mind.

  How much time do I need to purchase samples?

  Degree of accuracy these samples should be?

  How many channels do I need?

  What voltage range I have to read?

  You can start on the following link and choose the options on the left to get to the bottom for a few modules.

  http://sine.NI.com/NP/app/main/p/AP/global/lang/en/PG/1/SN/N25:device, n24:cRIO.

• Virtual LabVIEW Developer Days

  Dear experts LabVIEW,

  I think registration of the virtual Webcast LabVIEW Developer Days (from 15 to 17 May), but do not know if I have to pay any registration fees or watch the webcast. Advice or comments will be greatly appreciated.

  Sincerely,

  Fuh

  Dear Lynn,

  Thank you very much for your answer. I appreicate it. I search, but was unable to find anything saying that the webcast event is FREE. The fact that I can't find anything that indicates a charge does not mean that this event is free. I might have overlooked. So I think that prevention is better than cure. Actally, I sent a NI Marketing Manager (who sent a broadcast e-mail to many people, including me) on 25 April. Unfortunately, I don't have nothing heard back yet. I think that my email could have fallen a crack... Because I'm really thinking about the possibility to record the webcast event, I'm going with the last resource - post a question on the Discussion Board OR. Someone there may be able to help me.

  I'm sorry to post a question at a meeting of false. I've mixed up. Sorry! However, I appreciate your clarification. Now, I know (and am sure) this webcast event is FREE. I'll go ahead and sign up for this.

  Thank you much for your clarifications and have a nice day.

  Fuh

• I could develop Java Application for Blackberry device software version 5.0 to 6.0 JDE

  Hi, expert,

  I saw this line of the ' BlackBerry Java Development Environment - 4.7.0 - fundamentals Guide'.

  It is said:

  ===============================

  With each major version of the BlackBerry Device Software and the FMV of BlackBerry, Research In Motion includes the
  corresponding Java API and version of the BlackBerry® Java® development environment. The version of the BlackBerry device
  Software determines the version of the BlackBerry® integrated development environment that you can use to develop
  applications. For example, RIM released BlackBerry Device Software version 4.0 and BlackBerry JDE version 4.0 in even
  time. BlackBerry JDE version 4.0 supports APIs that were introduced in BlackBerry Device Software version 4.0
  and BlackBerry JVM version 4.0.

  The applications that you create by using BlackBerry JDE Version 4.0 only work on BlackBerry devices
  running BlackBerry Device Software version 4.0 or later.

  =========================

  The last sentence talking about version 4.0 of JDE. I think that would mean that I could not develop a java application on JDE 6.0 for Blackberry 5.0 version of the software, even if I do not use any new API to 6.0. However, it seems to me that it is a useless limitation. Could someone throw some lights on it?

  I'm going to agree with superdirt here.

  I have the 5.0 OS update of applications work well on OS 5.0, 6.0 and 7.0 of the OS OS phones.  I try not to recompile for levels of the OS, if I can, and so far I've been perfectly safe with OS 5.0 running on the later levels of the operating system.  So you should be able to get away with just using OS 5.0.

  Not that it is important for you, but I just thought I documents some historical information about level changes.  .

  As far as I know it 2 change cod in the file format, one to the 4.0 OS and the other in OS 4.2.  Therefore, if you want to run anything in OS 6.0 or above, it must be compiled in OS 4.2 or higher.  Again, I have applications compiled to OS 4.2 running on OS 6.0, without no problem devices.

  There have been changes to the API - the result is that the code that works in OS xx does not work in OS yy where yy is after xx.  I hit a few of them and have so far managed to rework the code so that it works very well on both levels of the operating system.  In general it is things that I do wrong anyway, as the older operating systems (from memory) are not as strict on when the event Thread must be used.

  The problem with OS 4.7 compatibility is an impact and to get more of this, for devices touch screen only, I compile using OS 4.7.  If an application that uses only the functionality that was available in the OS 4.2, I compile on OS 4.2 for non touch screen phones and OS 4.7 for touchscreen phones.  And everything works fine.

  I hope this helps.