Battery IdeaPad Z510 problem

Similar Questions

• BATTERY LENOVO IDEAPAD Z510 PROBLEM

  I bought Z510 a year back, in this short time I am facing battery problem. Battery won't charge and the system to keep plugged in a State with each use.

  I'm a home user and use the laptop for a limited time. I don't understand why lenova did not provide a removable battery that can be changed by the user only.

  Now new battery is not available on the market, also that Lenova simply made it their responsibility saying laptop in not less than warranty.

  I ask Lenovo go to analysis of root causes of this problem that hundreds of people face the same problem in this model.

  Hope Lenovo would provide some software to assist the problem or at least to give the details of the service provider where the batteries can be repaired or replaced.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Battery Lenovo Z510 problem

  Greetings! I have a Lenovo Z510 8 GB Ram, Core i7, 1 TB hdd, I bought less than a year ago. Off late I've known major battery issues. He started with the laptop stopping randomly without warning, even if there is a life on the left, for example. PCT of 90 or more. This worsened when the laptop did not start at all, until I plugged in the charger. The only way I can now exploit the laptop is connecting to the charger, but again, the battery remains at 0 of the pct, does not load. The battery light continues to flash red, also, I used a BatteryInfoView application to analyze it, and it still says battery reached 83 percent of its original capacity, however, I get a message every time at startup saying the battery is low and needs to be replaced. What can I do about it? Thank you.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• [Z510] Problems with the battery not charging

  I have ideapad z510 for almost a year. and now my unit still shows that it is at 0% battery. and she indicates that she battery level does not increase. and for this reason I could not use my unit when it is not plugged. What should I do about it?

  Comment to Moderator: New thread is created. The topic is edited to include the model.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• New battery for Ideapad Z510

  My Lenovo Ideapd Z510 battery died right after a year.
  and no one does it on this thread https://forums.lenovo.com/t5/Lenovo-P-Y-and-Z-series/Lenovo-Z510-Battery-Issues/td-p/2040767

  I want to buy a new battery for battery Ideapd Z510.
  Thus,.
  1 should. What battery I buy? What models and technical details?
  2. where can I get the Ideapd Z510 battery online in INDIA? That they are not available to Lenovo from retailer. ?

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Error starting IdeaPad Z510

  Hello

  its been only a week sincei bought new ideapad Z510.

  But now im having a problem that when I turn on the system, it does not, it just stays on the 'Lenovo' screen It will load only when I push the button of "key recovery" and select normal startup. I tried to restore the BIOS settings but no use. Please help me

  
  

• [SOLVED] Energy Win8.1 (Ideapad Z510) Manager

  Hello

  I am a new user of Lenovo (Ideapad Z510) with Win 8.1 and I have problems with a feature in Energy Manager (installed original Lenovo disk).

  In the settings menu, there is a function "zoom to screen." By using this feature, you should be able to enlarge and reduce the size of menus and icons using Fn + and Fn - buttons. I tried it and all my menus have become bigger, and I can't go back... Whenever I have press Fn - it just sort of plant. A few pictures to see the problem:

  (Sorry, that the menu is in Hungarian)

  (1) some features

  Link to photo

  (2) after pressing Fn - icon Manager duplicates the energy and all the bar becomes strange

  

  (3) all menus (right-click right, or even at the office) became huge

  Link to photo

  Thanks in advance for any help!

  Note of the moderator; image (s) converted into programming on display images in Forums

  Oh, it seems that it is now resolved. If, instead of using the cursor (it has been on the smallest) I went from police in the menu below from 11 to 10, and now it seems fine. I tried to solve the problem with the cursor before, but have not thought to decrease the font size.

  Thank you for the help, Jonas!

• How to install W8 in Mode for Lenovo Ideapad Z510 UEFI?

  Hello world

  I've been struggling with the w8 installation on my laptop Ideapad z510 in UEFI mode, but not I could succeed it or me I found something that might help. I will explain clearly the case.

  Point 1:
  As I understand it, for successful installation in UEFI format w8, we need choose the mode of 'First UEFI"from the Boot Menu in the BIOS. Then, the source of the shoe must be specified to identify the rigid path to documents to be loaded so that the new OS could be installed correctly.

  Pharmacodependance1:
  It is possible to choose UEFI boot mode first, but it is not possible to choose the USB for UEFI boot path in this case, which does not allow to succeed a UEFI boot to your computer. You cannot reach the DVD or USB, the installation files are, and start the installation process.

  Point2:

  If we consider the first case, you must choose the Legacy Support of your computer startup mode and achieve the USB or DVD drive to install the new operating system on the computer.

  Problem2:
  To succeed the UEFI mode when the computer starts, you should see 4 different partitions on your drive to the point of disc selection, if you choose the disk you install your operating system. However, when you select the Legacy Support in BIOS mode, the disk partition is limited to 2 in my case, that are:

  • Main drive
  • Reserved system (350 MB)

  That is why, when I continue the installation, the OS is installed on the traditional way. After installation, when I go into the BIOS to choose the UEFI boot mode for mode, the laptop checks some network connections and said

  • EFI network failure 0 for IPv4
  • EFI network failure 0 for IPv6

  respectively.

  So, advice, aid, ideas and suggestions are gladly welcome to overcome this problem. Could you please help me?

  PS: Please don't say that "you can't install because your computer does not support", because I have received computer technical service and a W8 version has been installed in UEFI mode. However, I deleted to install W8 pro.

  Greetings,

  Okan

  First of all, your bootable USB key must be created in the UEFI. Just google and you will find solutions.

  You can install W8 mode UEFI. Just allow to boot from USB in BIOS, select Exit Saving changes and restart.

  I think it's your basic problem. Let me know if you have already done this and still having the problem.

• How to invert the fn keys in ideapad z510

  Hello

  I recently bought a lenovo ideapad z510 and I have to press fn in order to use the f1 - f12 keys. Is there a way to change this trend so that I don't need to press fn to use the f1 to f12 keys?

  Hi moving.

  Welcome to the Community Forums of Lenovo!

  Can you try to go to BIOS by pressing F2 when you power on the system

  Once inside the BIOS look for an option that says mode HOTKEY or hotkey, should be under the configuration tab.

  change this option and must reverse the use of the FN on your system.

  (Remember to press F10 once your done to save the changes you made.

  

  If the hot key mode is not available in BIOS, you may have to wait or consult on the download site of the Lenovo Support for BIOS updates

  Hope this helps

  See you soon!

• BlackBerry Smartphones Blackberry PRIV battery drain & heating problem

  Hello Blackberry, team

  I bought PRIVATE released last week from classic BB. PRIV has severe heating and battery especially drainage problem while loading and between 100% and 40% of battery (drains 60%) in 1-2 hours.

  Note that I do not use heavy duty applications and it heats up even when kept or wait (especially during loading).

  My Apps are up to date

  Operating system is up to date

  I have restored several times, but still have the same question (even if no other apps are installed).

  Question: Is it a solution to this? BlackBerry is working on it or just forget it and move on to other brands?

  Finally and above all, I'm on Blackberry for the past 12 years... I really hope they take their clients seriously around the world.

  Hey parthz8,

  Sometimes it happened while the load when I got 5.1.1 but now with Android M 6.0 seems to be fixed.

  What I was doing when it was happening, it is to reset the phone with the power button for 10 seconds while it was still connected to the charger. Sometimes a couple of reset is necessary

  Ice

• BlackBerry Smartphones "BOLD" battery draining - overheating problems

  Hi all

  I'm new here I have BlackBerry for almost 2 years (curve 3000) and I was really happy with it (no problems) then I bought "BOLD" Saturday and has exhausted the battery - overheating problems! I downloaded the new software from T-Mobile Croatia site (they have one last but which did not help) after recharging and stay all night, he went flat within 6-7 hours so I went today (Monday) and they swapped the device for me, now I'm waiting to see what will happen. I have 4 questions:

  1 can I download new software version of the device from the BlackBerry site that even I bought in Croatia from T-Mobile and which will have consequences on the device? If yes what are they?

  2. what causes this battery drain - overheating problems and how they can be stopped?

  3. is Facebook app in conflict with "BOLD"? Yes I have it on mine.

  4 are all the other apps in conflict with it, i.e. Windows Live Messenger because I have too much that one on it?

  Thanks in advance!

  1. no consequence... the latest version of the "BOLD" OS device is located here:

  http://www.BlackBerryForums.com/General-9000-series-discussion-bold/194263-OS-9000-bold-4-6-0-477-4-...

  2 could be a number of issues, several. You have 3G enabled on your "BOLD", on the one hand, (manage connections > Mobile Network Options?, and you have a 3 G with Tmobile Croatia network?) I know not flippant, you could ask that. If your device is constantly looking for a 3 G network and not finding what will cause the big battery drain.

  Check your applications running in the background. There are usually four or five applications that will be always running (Messages, Call Logs/phone, BlackBerry Messenger, home screen and the browser; there are others such as BeamBerry and alarms which will run also). Ensure that the browser is NOT on an active Web page (must return the bookmarks page only). Close all other applications that do not need to be running (the camera or a game you were playing or Google Maps).

  3 No.The FB app is developed by RIM.

  4. What do you mean 'in conflict '?

  Read this on your battery and load:

  http://www.blackberrynews.com/2008/05/20/battery-use-tips-for-your-maximum-battery-life/

• alert! system battery is low problem for dell optiplex GX620 Tower

  alert! system battery is low problem for dell optiplex GX620 Tower, how do I fix or solve this problem, is this will solve by change coin cell? If yes than suggest me about the cell its name will be full description

  The battery is a battery CR2032 DL2032.  In the USA they are in grocery stores in the pharmacy section because the readers of blood sugar using the same battery.

  http://www.Walmart.com/c/KP/CR2032-batteries

  

  

• Lenovo Ideapad z510 Low Battery Warning problem

  Hello

  I had this problem with my laptop lenovo z510, there the quick battery charges, and when he pulled so used, it automatically turns offs without low battery warning. It turns off automatically. What do you think of his problem? Please help me. Thank you!

  Mod comment: picked up post for new problem. The topic is edited to include the model/number.

  
  

• Battery Z510 problem, battery is 0% all the time

  
  

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• IdeaPad S205 battery charge no problem

  Hello, I have a Lenovo IdeaPad S205 and met with some difficulties. The charger has recently stopped working and I bought a replacement - the original charger has a 20V power, whereas the replacement 19V power. However, I don't think it would make a difference. That being said, when I plugged in the charger, it says "plugged in, not load." I took the battery and put it again, in as I had a similar problem before, and making it fixed. The system remained on while the battery was out, and I noticed the battery percentage is not down while this replacement is plugged. In addition, the original now seems to do the same thing - "plugged in, not load." Can anyone offer any assistance?

  Hi Ben_R,

  It's weird. Can try you to:

  1 turn on the computer with just the AC adapter and loading Windows to the top, slide the battery and observe.

  2. turn off the machine with the inserted battery. When the machine is turned off, plug the AC adapter and see if the battery is charged.

  - Link to the image (i.e. battery light)

  Concerning