Battery not charging on Satellite Pro L300D

I've had this laptop about four months and had just returned a repair under warranty (replacement of the motherboard). He had light use since I bought it.

On his return, I ran a Windows 7 upgrade as installation clean but noticed that the battery charge more than 60%. I did turn the laptop today to try and run the battery down completely, then I might give it a full charge overnight.

All I get now when plug adapter is two pulses on the battery in the notification area icon and the message * "available (plugged in, load)" *-the icon remains on 'empty' despite being left for several hours.

It sounds like the battery is damaged or must recalibrate and if so, how?

Thank you

Try to start your laptop with power current only and when the OS starts put the battery inside and watch what happens with the State of the battery.
Have you contacted the service and reported on this subject?

Tags: Toshiba

Similar Questions

  • Battery not charging on Satellite M70

    I have a problem with my new M70: the battery does not charge at all, doesn't matter is the laptop that works on the sector, or completely off. Orange battery LED front turn United Nations only 3 seconds and turn off.
    The battery remains 2% of fees, and I can't charge?

    I also have an older laptop Toshiba satellite, and there arises the same thing a year ago!

    Any recommendations?

    Thank you
    Károly

    Hello

    I also recommend to check first the battery. I read somewhere that you can load and discharge the battery about 500 times. Then the battery will lose performance and will some time dead.

    If it of impossible to charge the battery again, so there must be something wrong with the hardware. In this case, the help of the service is necessary.

  • Unknown battery - not charging on Satellite P300D-11U

    HI -.

    I have a Satellite P300D-11U

    I have now bought 3 xtra different batteries. None of them will work - labtop doesn't recogninze any of them.
    Only the original supplied with the computer. When activated, it says Remaning time battery unknown / undetermined
    If I plug the power supply cord, it is said:
    No battery found, no charging current.

    Each shop/manufactor said it is a BIOS problem. That the BIOS cannot communicate with the battery.
    I installed the latest version of BIOS on 20 August 2008, no change - still the same.

    Is there a new current BIOS, or other solutions?

    Sincerely, Bryan

    Hmmm I have a U400 and the battery has been recognized after the BIOS update.
    Maybe it s not a BIOS issue but simply your battery or motherboard is not allowed.

    The warranty is valid?
    If Yes, you shouldn't t waste time and should contact the ASP in your country for a control of the laptop. The guarantee must cover everything!

    Good luck

  • Satellite Pro L300D - TOSHIBA DVD Player fails and does not

    Hello, I have the Toshiba Satellite Pro L300D, and I'm having a problem playing DVD on it. When you put them in the drive, it tries to load the DVD player, finally fails and says "DVD Player does not. If you try to load the DVD in the player it will freeze at 50% of the time,

    DVDs are fine, legal, were played on a DVD player and another computer without any problem. CD works fine in the same drive of my L300D.
    A popular entry.

    Hi lindag,.

    Is it so when you try to play DVDs with VLC media player?

    What you could also try is reinstalling DVD Toshiba playback software. You can download the latest version on the Web from Toshiba site:
    http://EU.computers.Toshiba-Europe.com
    ?

  • No noise and cache-battery not charging - Satellite L755 - 1 CD PSK2YE-08T00YFR

    Hello

    I have two problems with my toshiba L755 - 1 CD PSK2YE-08T00YFR

    1: no sound

    When I try to grab the microphone into the mic port, the sound Manager, it freezes and any use of sound programmes it freezes like vlc, I turn off the audio Manager Windows, disconnect me and logging devices device when I clicked in the sound icon troubleshooting the problem and the noise come buck and when I again seized the microphone he not freeze the sound Manager , I disable the audio device in the Windows Device Manager, and I continue to work without sound for 30 min ~ 1 h, I reboot my pc to start windows (windows 7, I don't remember what happens may detect a new device), I click on the sound icon troubleshooting two devices (photos attached) I chose 1 and it doesn't solve the problem but the speakers work not , I'm going to the sound Manager I see a disconnected device (maybe my card sound, pictures attached) and two new devices (attached pictures) and I see some changes in the reliable data connector (attached photos), and in the tab input device, I see a disconnected device (maybe my card sound, pictures attached) and three new device a MIC webcam (photos attached).

    before this problem the webcam and microphone webcam not working do not (I think I have hardware problem - webcam with sound card).

    I restart my pc and I chose "load factory default settings" from the bios when windows start detects a new device (webcam) but the sound does not (webcam and microphone webcam works fine now).
    I have try to disable the webcam and sound card, enable the sound card, reboot, load default... linux live cd... nothing, no noise.

    I try to test the bios beep, it works, I can hear a sound signal.

    I don't know how to solve this problem
    I need noise, I miss her, I can't do anything without the sound, please help me

    Attachment 558 Attachment 559

    2: battery not charging

    My maybe of battery 30 ~ 40%, when I suspend my pc (for 8 ~ 11: completely discharged battery) I forgot to load it, the morning I plugged it in HQ, 2 hours the led remains red when I turn on my pc and check the battery level, I see only 4% (hip, accused), I remove and buck battery but does not support he notices 4%.
    How can I recharge my battery?

    I need fix the sound problem

  • Satellite Pro L300D ubuntu and Driver Chicony Webcam

    Hi all

    Im having problems for my webcam to work on my Satellite Pro L300D laptop, its supposed to be for a Chicony b070.
    Before leaving, perhaps you should know Im using Ubuntu 8.04 Hardy Heron (still not improvement since this is a production machine).

    A more complete report can be found [here: https://answers.launchpad.net/ubuntu/+question/51545]

    Basically, the dev is created but it seems that HAL does not know how to work with it: S Im not even not sure Im in need of a driver in itself or just a tweak of config...

    Thank you for your time

    Hello

    As you can see for days nobody anything post here. I think the reason is quite simple. Linux is not supported and most people use the preinstalled operating system.
    I think you should try to find the answer on the Ubuntu forum. Here you can meet people with good experience of Ubuntu.

    If you find a solution please let us know. All useful info may help others here.

  • Satellite Pro L300D: Cannot install because of the common Modules control utility

    Hi guys,.

    I'm new to this forum, but I spent two days looking around.
    I have a sat Pro L300D that I'm downgrading to XP, because many are, and I can't get the touchpad to work or function buttons.

    One problem seems to be to install the utility 'controls', which gives the message "common modules" not installed even though it was the first pilot, I have installed.

    Does anyone have any suggestions?

    OK, here we go.
    Toshiba pilot European page doesn't provide drivers XP ALL, tools or utilities for the Satellite Pro L300D.
    Is this good? I checked the page and there are no. XP applications.

    So I came to the conclusion that the common Modules cannot be installed because this software was not designed for this series of portable and therefore, you receive this error message.
    It is clear!

    So Don t wonder what impossible to install "utility controls" or common modules. These pieces of software are not compatible

  • Satellite Pro L300D PSLC9E - failed to update BIOS

    Hi all

    I got a Toshiba Satellite Pro L300D Windows Vista Business, this isn't that four months, recently, he began to break up and whenever he did, I got a message to upgrade the BIOS.
    So I went to the Toshiba Site and I downloaded an updated BIOS yesterday and installed even today, during installation the PC frooze.
    I left it on and it stayed like that for four hours, then it turns off.

    Now, when I turn it on all that I get is the fan turns to nothing else.
    The powerleader was connected to the laptop all the time.

    Do you have any ideas on what I can do, I have heaps on the laptop I would not loose.

    Model is PSLC9E Satellite Pro L300D

    The case is clear buddy update the BIOS has no procedure
    Perhaps the BIOS might not be updated correctly because the laptop crashed until the update procedure could be completed.

    Well, I can tell you that you will not be able to fix it yourself it's a serious issue and ONLY the ASP (certified partner) would be able to help you!

    So contact the ASP technician and ask for later handling.

    Good luck

  • Devices Satellite Pro L300D-110 - downgrading to XP Pro - HARD drive missing?

    Hello to everyone in the Toshibe Satellite Pro - my first post forum.

    I was one proud owner of other portable Tosh without any problem, but this time, I'm miserable: (o)

    For professional use a few days ago, we bought a laptop Satellite Pro L300D 110 (AMD Athlon Dual Core). We bought it with the understanding that it could be brought back to XP Pro - mainly because some of the software that we use on a daily basis does not work reliably on Vista, but also because all other laptops to desktop computers in our network (including a WLAN) all running XP Pro, adding another machine that it should have been easy.

    The need to do so has been confirmed by the fact, nevertheless, I tried, we could just not get the new Toshiba L300D connection through our routers so that under Vista. At the same time, we also bought a new Dell with no o/s. I installed a new copy of XP Pro SP2 OEM - and it runs under the sweet as a nut! Sorry, I digress:

    I reduced the L300D to XP Pro very well using the XP Pro provided - Toshiba Recovery disk no problem at all. I had the computer connected to the network too, but then I realized that the DVD (Pioneer DVD - RW DVRTD08A ATA) is not found by Windows.

    Logged in the BIOS setup - Yes, he was listed there OK, but tried some tongs and tricks I have learned over the years, I still couldn't XP Pro to the discovery of the device.

    I have now reinstalled Vista on the machine and he found the DVD burner.

    If it's a PC, I shut down the computer, open the case, disconnect the writer, start, stop, reconnect the device, close case and bingo. But not with perhaps a laptop...

    Someone has ideas how (reliable!) downgrade to XP Pro without devices being endangered? Any help would be greatly appreciated.

    I have two copies again more XP Pro SP2 at my disposal, if that's any use.

    Kind regards

    David

    (> I'm happy again now: o)
    Great to hear that!

    Just for info:
    The most recent series of portable supports the newer SATA HDD controllers and so the operating system can be installed if the SATA drivers are not included and preinstalled.

    So if you want to use the SATA features you must first install the SATA driver.
    But you can also activate SATA mode to compatibility mode (in BIOS) and this would install the Win XP without the necessary SATA drivers.

    Good bye

  • Installation of Windows XP on Satellite Pro L300D-136

    Hello

    I realize that this question is very similar to those posed elsewhere on these forums. I tried after the solutions proposed elsewhere but were unable to do anything at work.

    I'm trying to install XP Pro on a Satellite Pro L300D 136, which is currently under Vista.

    I tried to get into the BIOS and change SATA compatibility mode, but I still get a blue screen of death when booting from the installation disc. Reading elsewhere on the forums, that I understand that I have to use nlite to include drivers SATA on the installation CD, I'm not sure how to find out what drivers I need. Number of threads talking about MSM from Intel, but my machine has an AMD Athlon processor. Does make a difference? Where can I find the necessary drivers in the download section of Toshiba?

    Thank you in advance for your help, this is the first time I tried to replace a windows with another OS...

    Yes, it makes a difference.

    For laptops equipped with AMD processor (they don t have an Intel chipset) you need the display driver.
    In the display driver package are the SATA drivers you need.
    You can find it on the Toshiba site:
    http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  • Satellite Pro L300D - 11 M - need drivers for Windows XP Home edition

    Good afternoon! Help to find the drivers on the operating system Windows XP for Toshiba Satellite Pro L300D - 11 M
    Thank you!

    If I have not clearly written something that you let me know please, I'm simple I do not speak English, I have Russian and to transfer, use the online translator.

    Master_of_Disaster

    Big thanks for help!

  • Satellite Pro L300D SP5802 tools and BONES

    Hi guys
    I just bought a Toshiba Satellite Pro L300D-SP5802 laptop and it has Windows Vista
    I have havve 2 recovery DVD. One of these States for Windows XP Professional.

    I would like to know before all formatting:

    1 XP Recovery DVDs will help me with the drivers, utilities, etc. When I install Windows XP?

    2. will I need an additional XP license? or can I use the key provided at the bottom of the laptop?

    3. some URLs to get the upgraded drivers for this model? (no info at toshibalatino.com)

    Thank you very much in advance

    Hello

    I'll try to answer your questions ;)

    1 recovery image contains all the drivers, tools and utilities and after recovery image installation you don't need to install anything. Everything will be installed correctly.
    2. don't you are useless there. This is image recovery and not typical installation where you must enter the product key.
    3. to give answer to this question, please let us know in which country you purchased your laptop.

    Good bye

  • Satellite Pro L300D loses wireless connection randomly then can never find

    Hello

    My Satellite Pro L300D loses the wifi connection at random times and I have to turn off the network for the L300D BT box to connect again. Throughout this, my other laptop Toshiba works fine on the network, as does my PC, so the network is fine.

    It's incredibly frustrating because I have a new baby and get NO SLEEP - I just need the L300D blasted to work!

    Any help would be good and would save me lose any more hair.

    Thank you

    James

    one of the two: or the Ruter have electrical problems, but you said that another computer is not working properly, so it must be a physical problem with the unit your problematic computer wireless, if wireless is the drop of water at all times, you must check this problem with a service provider.

    If you don't know where you can find one, visit this Web page to locate your nearest Prov. Serv.

    http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_gaspLocator.jsp?subs=TAIS

    I hope this helps.
    / * HEAVY METALL. \

  • Satellite Pro L300D-138 restarts on shutdown

    Hello

    I recently bought a Satellite Pro L300D-138, and I also got one for my parents. Almost every time that I stopped it, it restarts automatically. I think it happens when there are updates that are installed, but I think it could happen even if it is not updated. I don't get messages that say, 'news updates, restart necessary.' or whatever it is. I thought also restarts of updates required as such, but that shut down the computer and then turn it on again tomorrow, or anything that would complement the updates. Maybe I'm wrong... ? Y at - it somewhere I want to wait for new update/restart applications?
    It's not a big deal, really, it's just a bit of a pain in the @55 to return the laptop to close again a few minutes after turned it off, it... I am making sense? I feel I am repeating myself! :)

    This happens also with the laptop I got for my parents, so I assume it's a Toshiba, or something new computer thing, I just want to know if I can make him stop or if I have to put aside 10 minutes to close the bottom!
    Cheers for any help!

    Ailbhe

    Checkbox rdi posted.

    Also make sure that if this happens only if there are no updates to update will be installed because it might be the reason for the restart.

  • Can I get the battery 9-cell for Satellite Pro U400 - 13G?

    Hey

    Can someone tell me if it is possible to get a battery 9 cells for Satellite Pro U400 - 13G.
    And if it is then what is the part number?

    Best regards Anders

    You know the Web from Toshiba website Options & accessories?

    See this page:
    http://EU.computers.Toshiba-Europe.com-> peripheral services & -> PS Options & accessories

    There you will find all the compatible options.

    AFAIK this battery could be compatible with the Satellite Pro U400 series:
    * Battery Pack (Li-ion, 9 cell, 6000mAh) PA3537U-1BRS *.

    Good bye

Maybe you are looking for

  • Compatible LCD Panel for Satellite M30 951

    Unfortunately, the display on a Satellite M30 (PSM30E-7101Y-GR) is broken. Well, to change it would not be a great thing, but I would like to know what screen models when used on this Version (for example is it possible to build in a style of glare p

  • HP DesignJet 430: HP DesignJet 430 and win 10 64-bit - required driver signing enforcement?

    Hello. Is the deactivation of the application of driver signing Win 10 required to install this printer HP DesignJet 430 64-bit (driver Vista or XP 64-bit): hpdj430x64glen.exe version 4.83 (I think) A customer wants the 430 to work with Win 10 64 bit

  • How to connect the chassis cDAQ for strain gage

    Hi, when I read the guide of the extensometer of wiring on a chassis cDAQ (http://www.ni.com/white-paper/7130/en) I found confusing fig 10 . What are the things between the chassis and the extensometer? The three wires go only one channel of the cDAQ

  • HP Officejet Pro 8630: Hp Officejet Pro 8630 enlarger of fonts?

    Anyone know how to enlarge the font size through the only printer for a paper on the printer tray?  Thank you.

  • Detect the color of the fuses

    Hello I have an electronic card which has several fuses with different colors. I want to develop a program of LabWindows that allows me to detect if the color of the fuses is good or not. Can you tell me if Labwindows contains libraries for this work