Baud rate for the connection of the Console on ASA 8.6 (1)

Hi all

I need to use very long console connection it more than 56 feet (17 m) (I used the cable Cat6 with connection on oth ends as console 12345678 87654321)

According to the table below

Speed (bps) Distance (m)

2400

60

4800

30

9600

15

19200

7.6

38400

3.7

56000

2.6

My son goes to manage the serial connection.

On the router, I can use

Router> terminal speed 4800

I could not find similar command on ASA IOS - id a whole?

If I'm going in the wrong direction extending series thread made me know.

Thank you

I'm sure that you can change the speed of console ASA to the default of 9600 bps. 15 m is not much less than 17 m - have you tried your connection without success?

If this does not work you will probably have to a. use a server console ports or (b) rely on Ethernet management intertface.

Tags: Cisco Security

Similar Questions

  • Definition of FD CAN baud rate gives the error (using samples of C)

    I use C for XNET "FD CAN Frame Input Stream" samples where I put the valid values of "nxPropSession_IntfCanFdBaudRate" between 1000000-8000000. (according to http://www.ni.com/pdf/manuals/372840k.pdf#page=983)

    I am getting following error

    NOR-XNET status: NOR-XNET: baud rate (Hex 0x3FF63040) The FD CAN you provided is beyond the capability of the manufacturer of the specified transmitter/receiver. In our internal testing, we found this baud rate to run, but bus errors may be detected or generated during communication. See the Presentation of the material NOR-XNET CAN section in the software and manual equipment OR XNET for more information.

    I have a loop back configuration with a PCI card with 2 ports.

    It is a warning and not an error to inform you that you may be exceeding the capacity of the physical hardware. While the FD CAN protocol supports very fast transfer speeds, none of the manufacturers transcevier still created talkies that they ensure that all transfer speeds. Talk to them, the number one problem was do an EMC low enough to run in the vehicles. They tend to be actually able to follow the signaling rate.

    Therefore, we allow you to use NOR-XNET to communicate to a wide range of transmission speeds, but sound you the alarm if you are exceeding the rates allowed by the manufacturer. For most use cases, this can be ignored safetly.

    FYI, what baud rate you try to run to?

  • Units of the number of samples and rates for the DAQ Assistant units

    Hello

    I use the DAQ assistant for analog voltage of an input OR data acquisition card. What is the difference between the rate and the number of samples in the DAQ assistant and what are the units of the two?

    Thank you.

    The number of samples is how many discrete to measures. Rate (per second) is how fast to acquire the specified number of samples.

    If number of samples is 100 and the rate is 1000 samples per second, then the acquisition would take 0.1 second (100 / 1000).

    -AK2DM

  • Rate for the low number of County Digital events

    Hello

    I'm trying to use the example of digital counting examples DAQmx Events.vi to count the pulses of a photon counter.  As long as the light level is high enough, it works very well. But, when the light level is below a threshold, no count is read. I checked that's not because of the photon counter by testing with an independent instrument.

    It seems like it might have something to do with the rate at which counted events are unloaded (PCIe-6321) hardware in the computer, that is, there is a minimum threshold of count indictment before such a transfer of data occurs. I'm voting for the number of levels of every 100ms.

    Any help would be appreciated.

    Thank you

    Alex


  • I bought a flat monthly rate for the images of the reserve, but it looks that I signed up for a year by mistake. I really wanted to plan for a month. Is there a way I can get out of this?

    When I was going through the purchase plan options, it seemed that I buy a monthly. I had no idea I have would be linked a year. We really didn't have in this regard. Is it possible that I can get out of it. I really wanted a plan for a month not year whole.

    I will organize the plan must be cancelled, so it is not renew next month.  You can use the images for the first month.

    Kind regards

    Bev

  • Problem with the VPN site to site for the two cisco asa 5505

    Starting with cisco asa. I wanted to do a vpn site-to site of cisco. I need help. I can't ping from site A to site B and vice versa.

    Cisco Config asa1

    interface Ethernet0/0
    switchport access vlan 1
    !
    interface Ethernet0/1
    switchport access vlan 2
    !
    interface Vlan1
    nameif outside
    security-level 0
    IP address 172.xxx.xx.4 255.255.240.0
    !
    interface Vlan2
    nameif inside
    security-level 100
    IP 192.168.60.2 255.255.255.0
    !
    passive FTP mode
    network of the Lan_Outside object
    192.168.60.0 subnet 255.255.255.0
    network of the NETWORK_OBJ_192.168.1.0_24 object
    subnet 192.168.1.0 255.255.255.0
    network of the NETWORK_OBJ_192.168.60.0_24 object
    192.168.60.0 subnet 255.255.255.0
    object-group Protocol DM_INLINE_PROTOCOL_1
    ip protocol object
    icmp protocol object
    object-group Protocol DM_INLINE_PROTOCOL_2
    ip protocol object
    icmp protocol object
    object-group Protocol DM_INLINE_PROTOCOL_3
    ip protocol object
    icmp protocol object
    Access extensive list ip 192.168.60.0 Outside_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
    Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
    Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
    Inside_access_in list extended access allow DM_INLINE_PROTOCOL_2 of object-group a
    network of the Lan_Outside object
    NAT (inside, outside) interface dynamic dns
    Access-group Outside_access_in in interface outside
    Inside_access_in access to the interface inside group
    Route outside 0.0.0.0 0.0.0.0 172.110.xx.1 1
    Timeout xlate 03:00
    Pat-xlate timeout 0:00:30
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    identity of the user by default-domain LOCAL
    AAA authentication http LOCAL console
    Enable http server
    http 192.168.60.0 255.255.255.0 inside
    http 96.xx.xx.222 255.255.255.255 outside
    No snmp server location
    No snmp Server contact
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
    Crypto ipsec ikev2 ipsec-proposal OF
    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    card crypto Outside_map 1 corresponds to the address Outside_cryptomap
    card crypto Outside_map 1 set peer 96.88.75.222
    card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
    Outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    Crypto ikev2 allow outside
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    authentication crack
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 20
    authentication rsa - sig
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 30
    preshared authentication
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 40
    authentication crack
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 50
    authentication rsa - sig
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 60
    preshared authentication
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 70
    authentication crack
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 80
    authentication rsa - sig
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 90
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 100
    authentication crack
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 110
    authentication rsa - sig
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 120
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 130
    authentication crack
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 140
    authentication rsa - sig
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 150
    preshared authentication
    the Encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH stricthostkeycheck
    SSH timeout 5
    SSH group dh-Group1-sha1 key exchange
    Console timeout 0
    inside access management

    dhcpd address 192.168.60.50 - 192.168.60.100 inside
    dhcpd allow inside
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    WebVPN
    AnyConnect essentials
    internal GroupPolicy_96.xx.xx.222 group strategy
    attributes of Group Policy GroupPolicy_96.xx.xx.222
    VPN-tunnel-Protocol ikev1, ikev2
    username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
    tunnel-group 96.xx.xx.222 type ipsec-l2l
    tunnel-group 96.xx.xx.222 General-attributes
    Group - default policy - GroupPolicy_96.xx.xx.222
    96.XX.XX.222 group of tunnel ipsec-attributes
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    pre-shared-key authentication local IKEv2 *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    inspect the icmp error

    ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    Cisco ASA 2 config

    interface Ethernet0/0
    switchport access vlan 1
    !
    interface Ethernet0/1
    switchport access vlan 2
    !
    interface Vlan1
    nameif outside
    security-level 0
    IP address 96.xx.xx.222 255.255.255.248
    !
    interface Vlan2
    nameif inside
    security-level 100
    IP 192.168.1.254 255.255.255.0
    !
    passive FTP mode
    permit same-security-traffic inter-interface
    permit same-security-traffic intra-interface
    network of the Lan_Outside object
    subnet 192.168.1.0 255.255.255.0
    network of the NETWORK_OBJ_192.168.60.0_24 object
    192.168.60.0 subnet 255.255.255.0
    network of the NETWORK_OBJ_192.168.1.0_24 object
    subnet 192.168.1.0 255.255.255.0
    object-group Protocol DM_INLINE_PROTOCOL_1
    ip protocol object
    icmp protocol object
    object-group Protocol DM_INLINE_PROTOCOL_2
    ip protocol object
    icmp protocol object
    object-group Protocol DM_INLINE_PROTOCOL_3
    ip protocol object
    icmp protocol object
    object-group Protocol DM_INLINE_PROTOCOL_4
    ip protocol object
    icmp protocol object
    Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_2 of object-group 192.168.1.0 255.255.255.0 192.168.60.0 255.255.255.0
    Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
    Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
    Inside_access_in list extended access allow DM_INLINE_PROTOCOL_4 of object-group a
    pager lines 24
    Enable logging
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    no permit-nonconnected arp
    NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.60.0_24 NETWORK_OBJ_192.168.60.0_24 non-proxy-arp-search of route static destination
    !
    network of the Lan_Outside object
    dynamic NAT (all, outside) interface
    Access-group Outside_access_in in interface outside
    Inside_access_in access to the interface inside group
    Route outside 0.0.0.0 0.0.0.0 96.xx.xx.217 1
    Timeout xlate 03:00
    Pat-xlate timeout 0:00:30
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    identity of the user by default-domain LOCAL
    AAA authentication http LOCAL console
    Enable http server
    http 192.168.1.0 255.255.255.0 inside
    http 172.xxx.xx.4 255.255.255.255 outside
    No snmp server location
    No snmp Server contact
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
    Crypto ipsec ikev2 ipsec-proposal OF
    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    card crypto Outside_map 1 corresponds to the address Outside_cryptomap
    card crypto Outside_map 1 set peer 172.110.74.4
    card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
    Outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    Crypto ikev2 allow outside
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    authentication crack
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 20
    authentication rsa - sig
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 30
    preshared authentication
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 40
    authentication crack
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 50
    authentication rsa - sig
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 60
    preshared authentication
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 70
    authentication crack
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 80
    authentication rsa - sig
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 90
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 100
    authentication crack
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 110
    authentication rsa - sig
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 120
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 130
    authentication crack
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 140
    authentication rsa - sig
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 150
    preshared authentication
    the Encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH stricthostkeycheck
    SSH timeout 5
    SSH group dh-Group1-sha1 key exchange
    Console timeout 0

    dhcpd address 192.168.1.50 - 192.168.1.100 inside
    dhcpd allow inside
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    WebVPN
    AnyConnect essentials
    internal GroupPolicy_172.xxx.xx.4 group strategy
    attributes of Group Policy GroupPolicy_172.xxx.xx.4
    L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
    username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
    tunnel-group 172.xxx.xx.4 type ipsec-l2l
    tunnel-group 172.xxx.xx.4 General-attributes
    Group - default policy - GroupPolicy_172.xxx.xx.4
    172.xxx.XX.4 group of tunnel ipsec-attributes
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    pre-shared-key authentication local IKEv2 *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    inspect the icmp error
    inspect the http

    For IKEv2 configuration: (example config, you can change to encryption, group,...)

    -You must add the declaration of exemption nat (see previous answer).

    -set your encryption domain ACLs:

    access-list-TRAFFIC IPSEC allowed extended LOCAL REMOTE - LAN LAN ip

    -Set the Phase 1:

    Crypto ikev2 allow outside
    IKEv2 crypto policy 10
    3des encryption
    the sha md5 integrity
    Group 5
    FRP sha
    second life 86400

    -Set the Phase 2:

    Crypto ipsec ikev2 ipsec IKEV2-PROPOSAL
    Esp aes encryption protocol
    Esp integrity sha-1 protocol

    -set the Group of tunnel

    tunnel-group REMOTE-PUBLIC-IP type ipsec-l2l
    REMOTE-PUBLIC-IP tunnel-group ipsec-attributes
    IKEv2 authentication remote pre-shared-key cisco123


    IKEv2 authentication local pre-shared-key cisco123

    -Define the encryption card

    address for correspondence CRYPTOMAP 10 - TRAFFIC IPSEC crypto map
    card crypto CRYPTOMAP 10 peer set REMOTE-PUBLIC-IP
    card crypto CRYPTOMAP 10 set ipsec ikev2-IKEV2-PROPOSAL
    CRYPTOMAP interface card crypto outside
    crypto isakmp identity address

    On your config, you have all these commands but on your VPN config, you mix ikev1 and ikev2. You have also defined political different ikev2. Just do a bit of cleaning and reached agreement on a 1 strategy for the two site (encryption, hash,...)

    Thank you

  • which product is right for the ssl vpn: asa 5505 cisco 1841 or

    Hello

    I want to install an outside link management related so that we can ssh to our cisco devices and microsoft RDP toour servers. It's my configuration (based on what I know):

    Internet > DSL modem > ASA 5505 > management CONSOLES SWITCH > SWITCH CISCO or Windwos Server

    or

    Internet > 1841 with DSL HWIC > management CONSOLES SWITCH > SWITCH CISCO or Windwos Server

    My questions are:

    Should I go for ASA or 1841 router?

    What options is better? and ASA will do the job?

    Are there any technical support prior to purchase of products in Australia? I need technical advice on the choice of the right products, not justs eiling me products.

    Hello

    Its strongly suggested to go with ASA 5505 in the first place, it is supposed to feature for the main functionality of ssl vpn server from 1841 which has this feature to be a vpn server.

    ASDM also gives you the freedom to config box on your own based on your condition.

    regds

  • Where can I find the maximum bit rate for the NI SHC68-C68-RDIO2 cable

    Search on the web site without success - maximum performance measured is an important specification!

    Hello

    in this case, we should look at the whole system. 1082 chassis is large enough for 2 cards. What are the other maps are built into the system?

    The 7021R SMU has in the datasheet of a limit on the transfer rate of data to the SMU Backplane of the chassis, which is 500 MB/s.

    I advise you in this case through the technical sales department. You can reach me by phone or email:[email protected].

    We can discuss the whole of the project.

    Best regards

    Lucia

  • Setting baud rate to the Max with OpenComConfig.

    I want to connect to a motor controller (Newport Conex CC) using the serial port, but it takes baudrate 921600, however, the maximum value allowed baudrate in OpenComConfig() is only 256 000. Is there a way around it.

    Also, I tried HyperTerminal and everything works fine with the baudrate 921600

    I can say that the viSetAttribute depending on the VISA library works up to 921600 transfer speeds, I have not tried with OpenComConfig.

    But others have, as you can see here: you can use higher rates as long the driver itself (provided by the manufacturer of your hardware to port) support non-standard transfer speeds; the limit referred by you is only a limited selection of presets of the Service Commission.

  • Can't access the internet - easy question for the experts! (ASA 5510)

    Dear all

    I can't access internet from my home network!

    I don't know why!

    Router:

    Ethernet f0/0 interface: 195.xxx.xxx.17/29 (to connect to the router) IP

    THE ASA NETWORK

    The external interface e0/0: 195.xxx.xxx.18/29 IP (to connect to the router)

    Internal interface: e0/1: IP 10.10.100.1 mask 255.255.252.0

    The ASA configuration

    ASA Version 8.0 (2)

    !

    ciscoasa hostname

    domain.com domain name

    enable encrypted password xxxxxxxxxxxx

    names of

    DNS-guard

    !

    interface Ethernet0/0

    nameif Interface_to_cisco_router

    security-level 0

    IP address 195.xxx.xxx.18 255.255.255.248

    !

    interface Ethernet0/1

    nameif Int_Internal_domain

    security-level 100

    address 10.10.100.1 IP 255.255.255.0

    !

    interface Management0/0

    nameif management

    security-level 100

    IP 192.168.1.1 255.255.255.0

    management only

    !

    xxxxxxxxxxxxx encrypted passwd

    boot system Disk0: / asa802 - k8.bin

    passive FTP mode

    clock timezone WEST 0

    clock summer-time WEDT recurring last Sun Mar 01:00 last Sun Oct 02:00

    DNS domain-lookup Interface_to_cisco_router

    DNS domain-lookup Int_Internal_domain.com

    DNS server-group DefaultDNS

    Server name 195.22.0.136

    Server name 195.22.0.33

    domain.com domain name

    permit same-security-traffic intra-interface

    object-group Protocol TCPUDP

    object-protocol udp

    object-tcp protocol

    Interface_to_router_Cisco_access_in list extended access allowed object-group TCPUDP any any eq field

    Interface_to_router_Cisco_access_in list extended access permit tcp any any eq www

    pager lines 24

    emergency logging level list Registo_eventos_william

    emergency logging list level Registo_eventos_william class vpn

    asdm of logging of information

    exploitation forest-address recipient [email protected] / * / critical level

    management of MTU 1500

    MTU 1500 Interface_to_router_Cisco

    MTU 1500 Int_Internal_domain

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 602.bin

    don't allow no asdm history

    ARP timeout 14400

    Global interface (Interface_to_router_Cisco) 101

    NAT (management) 101 0.0.0.0 0.0.0.0

    Access-group Interface_to_router_Cisco_access_in in the Interface_to_router_Cisco interface

    Route 0.0.0.0 Interface_to_router_Cisco 0.0.0.0 195.xxx.xxx.17 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout, uauth 0:05:00 absolute

    dynamic-access-policy-registration DfltAccessPolicy

    Enable http server

    http 10.10.100.0 255.255.255.0 Int_Internal_domain

    http 10.10.10.0 255.255.255.0 management

    http 195.xxx.xxx.16 Interface_to_router_Cisco 255.255.255.248

    http 192.168.1.0 255.255.255.0 management

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    No encryption isakmp nat-traversal

    Telnet 10.10.100.0 255.255.255.0 Int_Internal_domain

    Telnet timeout 5

    SSH timeout 5

    Console timeout 0

    dhcpd address 10.10.100.20 - 10.10.100.250 Int_Internal_domain

    dhcpd dns 10.10.100.2 195.22.0.136 interface Int_Internal_domain

    dhcpd lease interface 345600 Int_Internal_domain

    dhcpd domain domain.com Int_Internal_domain interface

    enable Int_Interna_domain dhcpd

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    !

    class-map inspection_default

    match default-inspection-traffic

    Thanks in advance

    MP

    Hi MP,.

    Based on the configuration below, only traffic since the possible management interface to access the internet.

    Global interface (Interface_to_router_Cisco) 101

    NAT (management) 101 0.0.0.0 0.0.0.0

    You must include your inside interface in the nat statement if you want to have the traffic within the internet go.

    Example:

    NAT (Int_Internal_domain) 101 0.0.0.0 0.0.0.0

    Kind regards

    Arul

    * Rate pls if it helps *.

  • Windows 7 computer to dial the connection problem with baud rate setting do not stay together

    I've set the com port [converter usb to serial com cable 5] setting baud rate to 115200

    I set up the adjustment [communication between 2 computers cable] modem baud to 115200

    In the center of network share, I create a new network connection [set up a dial-up connection]

    When I check the properties of the dial-up Modem connection set to 19200

    I can't change to 115200 - but the connection is attempted to 19200, so it fails

    All solutions?

    Hello Stephen,

    Thank you for visiting the Microsoft Community Forum.

    According to the description, I understand you are trying to reset the baud rate for your dial-up connection. You tried to change the BAUD rate in your login from 19200 to 115200, but the connection attempt is made at 19200 and if it fails every time.

    I suggest you to check with your ISP (Internet Service Provider), if they have their own custom settings saved using an application that controls the baud rate.

    You can also view the following Microsoft help articles.

    SerialPort.baudrate, property

    http://msdn.Microsoft.com/en-us/library/cc561279.aspx

    SerialPort.BaudRate enumeration.

    http://msdn.Microsoft.com/en-us/library/cc561279.aspx

    Hope this information is useful. Please write us back for any further assistance.

  • Need help in the choice of the tax rates for given the sales order

    Hello.

    Could you please say in the choice of the tax rates for the sale.

    Thanks, Sarath.

    Hi Sikora

    The next package will help you to search applied, fresh and total order fee

    OE_OE_TOTALS_SUMMARY. PRT_ORDER_TOTAL (OOH.header_id),

    OE_OE_TOTALS_SUMMARY. Taxes (OOH.header_id),

    OE_OE_TOTALS_SUMMARY. Costs (OOH.header_id)

    Kind regards

    Akil

  • Installation Partition problem (allocated too expensive for the Service Console?)

    Installation Partition problem (allocated too expensive for the Service Console?)

    RAID1 (15K 146 GB SAS) on Dell R710 and VMFS is on table EQL.

    What I did during the ESX4.1 excavation, it's that I have used ALL the space in 146 GB (mainly for / and / var), after adding this ESX host to vCenter, VC and EQL ASM/VE started to complain about the following points:

    1 VC: health check of localstorage warning (only has 245 MB left on 146SAS localstorage)

    2 EQL ASM/VE: warning rootFolder folder (due to the above)

    I thought that he is authorized to use all the space for / (50 GB) and / var (50 GB) in my case for only 146 GB, I don't think I need to leave any space on the installation disc.

    Could someone share some lights here?

    Thank you

    As you can see SDS use all the SDC VMFS partition space.

    This create the alarm.

    The thing really confused me why I have to leave a space on the disk at all?

    Technically there is no reason to let the space... but also no reason to have a big service console

    Usually, you need 10 to 20% free space for each snapshot data store and Exchange files... but in your case, you will not have these files.

    If you have any problems, but you receive the alarm until you do not disable them on this specific data store.

    PS: I suggest you switch to ESXi, is quite simple and it doesn't have this strange vmdk for the "console".

    André

  • Setting of baud rate with CVI runtime for Linux

    Hello people,

    I have a problem regarding the setting of baud rate with the CVI for Linux runtime.

    I want to communicate with a device that has a USB-to-serial of FTDI chip. The driver for this device is already included in the kernel (openSUSE 11.1, 2.6.27.23 - 0.1 - default i686 kernel).

    I can use a terminal program (HTerm 0.8.1beta) to open the serial port at/dev/ttyUSB0 and can set all baudrates, the unit supports (38400, 115200, 921600) and communication works perfectly.

    Now I take the example of series of NEITHER and go under Windows. I developed to support 921600 baud, and it works very well. So I try to run this example on Linux (I've expanded in order to open/dev/ttyUSB0), but it only works for 38400 baud. If I try to put 115200 or 921600 baud, then I get error RS232-14 (invalid baud rate).

    It would be nice if there is someone who can give me a suggestion what I need to do to get the job to 921600 baud.

    Best regards

    Martin

    Hi NickB,

    the patch done!

    Thank you very much.

    Best regards

    Martin

  • GANYMEDE user through the console?

    Hi all

    We had a strange problem with authentication via GANYMEDE. Logging on to a switch via VTY works well... I enter my user name and PW and start at the privileged exec prompt. But when I am trying to connect through the console, I won't get it priviledge rights exec without entering in a passage of the ena. This phenomenon occurs in different versions of IOS.

    Config looks like this:

    AAA new-model

    AAA authentication login default group Ganymede + local

    the AAA authentication enable default group Ganymede + activate

    default AAA authorization exec group Ganymede + none

    AAA authorization network default group Ganymede + local

    AAA accounting send stop-record an authentication failure

    AAA accounting newinfo periodic update 15

    AAA accounting exec default start-stop Ganymede group.

    orders accounting AAA 15 by default start-stop Ganymede group.

    Default connection accounting AAA power Ganymede group.

    !

    username privilege 15 password

    RADIUS-server host x.x.x.x

    RADIUS-server host x.x.x.x

    RADIUS-server timeout 25

    radius-server key

    Line con 0

    exec-timeout 0 0

    line vty 0 4 aso.

    Any ideas?

    Kind regards

    Sebastian

    Sebastian

    What you are experiencing is a behavior of Cisco implements voluntarily. As has been explained to me, to directly enter mode privilege is a combination of authentication and authorization. For the vty ports it is enabled. For the console, it is the authentication, but not the component of the authorisation. The reason for this is that it is easy to misconfigure the framework for approval of the configuration. It's one thing to lock you into the vty ports and it's something of another (and more serious) If you lock you out of the console. So as a safety mechanism Cisco only default not apply permission on the console. You will need to enter the password to enable on the console.

    HTH

    Rick

Maybe you are looking for