BB10 Simulator on Vmware ESXi

Similar Questions

• The adjustable BB10 Simulator it is date and time automatically?

  I have the installer of BB10 Simulator (10_2_1_2234) and works generally well on my Mac OSX (10.9.2 Maverics) system using VMWare Fusion 6.0.2 (1398658).  Everthing is in the latest versions as far as I can tell.

  However, even if in the settings / Date and time, the "Set Date and time automatically" switch to "On", whenever I start it, it displays the last time I used it.

  I need to manually enter settings / Date and time, turn the "Set Date and time" automatically to 'Off', set the date and time manually, then I turn the "Set Date and time automatically" button return to 'On '.

  My application itself is able to send and receive data over the network.  I can use the "Browser" application to see the web sites.

  How can I do set the date and time automatically?  Y at - it VMWare Fusion setting, I need to change?

  Thank you

  Ed Federmeyer

  If you resume your virtual machine session, the time that the virtual machine has been suspended is used.  If you "Power Off" the simulator it will update it's time to start.

• BB10 Simulator on Mac hangs just at startup - Parallels 7

  The BB10 Simulator works on Parallels 7?

  I was able to get the things installed but when I run it it crashes. Any suggestions?

  Thank you

  

  This is not a tested configuration.  The Simulator can run in native mode in VMWare Player on Mac, so you should use Parallels.

• BB10 Simulator speed is low

  Hi all

  I had a problem about the very slow speed of the BB10 Simulator. I installed VMware 5 and the BB10 simulator 10_0_09-1101. The hardware configuration of VMware to run the Simulator was the following: memory: 1.5 G, number of processor cores: 2. I run the software on my laptop HP pavilion dv5 (corei3 2.27 G, 3 G Ram, graphics intel HD).

  Is the configuration of my laptop, not enough to run the Simulator or I don't have some setting or configuration? I'm looking forward to your media.

  Thank you

  have you enabled virtualization in the bios of your computer?

• Cannot deploy the bar file BB10 Simulator.

  As the title,

  I have try all the possible method to deploy my bar of file Simulator BB10 running on VMware player without a bit of luck.

  The IP address that I use is the one indicated in the developer section of the simulated device:
  169.254.0.1

  no luck, I can't even ping the device to the windows console.

  Any idea?

  If you are connected to a VPN, it can cause connection problems to the Simulator.

  Could you try reboot the Simulator in bridged mode?  You can change this under the network option in the settings of your virtual machine.  If you do not have to go through NAT, which could cause you problems, this will put the Simulator on your physical network card.

  Also are you able to telnet/ftp to the Simulator?  You can identify yourself as devuser/devuser.

• Upgrade VMware ESXi 6.0 Update 2 VMware ESXi 6.0

  Hello I am running my PowerEdge T110 II with VMware ESXi 6.0 - Dell customized image. I see that from April 15, 2016 Dell just introduced VMware ESXi 6.0 Update 2 and I'd like to update my system.

  On the download page , I see there is an option to download and the ISO file. I wonder if this installation will completely be wipeout my existing VMware ESXi 6.0 - Dell custom and all the settings and I have to start all over again or update 2 ISO just 'modernize' my network?

  Hello

  You can use it to update without doing a new install. KB.VMware.com/.../Search.do; cmd = displayKC & externalId = 2109711 #Inter

• VMware ESXi monitoring

  Hi all

  does anyone have experience with followed Bigbrother to host VMware ESXi?

  In particular, I am interested monitor consumption of resources (CPU, memory, data warehouses) ESXi hosts.

  I am happy to receive any information about this topic:

  -experience in general

  -scripts

  -Links to the already existing scripts or documentation

  - ....

  Best regards

  Stefan

  Hello Stefan,

  There is an existing extension that accomplishes what you want and it can be found at http://communities.quest.com/docs/DOC-5658 - I have not implemented this myself, but I've heard other users that it works very well. Let us know if this is consistent with what you are looking for, and we would be happy to help you with questions of integration.

  Best,

  John McNelly

  Big Brother Team

• R710/R720 - Dell customized Image of VMware ESXi 5.5 Update 2 - megaraid_sas version specific?

  That I improve a R710 and two v5.5 (Dell image) to v5.5 U2 ESXi ESXi R720 using the image of Dell here:

  www.dell.com/.../DriversDetails

  The documentation "Upgrade Guide to ESXi 5.5 using Dell customized Image" here:

  www.Dell.com/.../manuals

  indicates that a specific version of the megaraid_sas driver must be installed.

  Is the version megaraid_sas that installs with the image of Dell U2 v5.5 not the right version?

  I just ran the upgrade on a R710 and it's the megaraid_sas version installed:

  ~ # vmkload_mod s megaraid_sas | grep Version
  Version: Version 06.803.73.00, build: 1331820, Interface: 9.2 inspired: August 22, 2014

  Thank you.

  Hello

  It lists the R720 and R710 systems supported and both link to the same page, so the customized version is the same for both servers. Is the version listed in the reference guide for A02

  megaraid_sas - 06.803.73.00

  Page 5 ftp://ftp.dell.com/Manuals/all-products/esuprt_software/esuprt_virt_solutions/vmware-esxi-5_Reference%20Guide6_en-us.pdf

  This is the same version that he shows for your installation on the R710 so that seems correct.

• Is the PowerEdge R610 Compatible DELL VMware ESXi 5.1 update 1 recovery Image?

  Hi all

  Does anyone know if the R610 is compatible with the recovery Image VMware ESXi 5.1 update 1? It is not on the compatibility list, but the r.620 is there. We use two servers in our VMWare environment and I want to upgrade to 5.1 U1.

  Thanks in advance!

  Lee

  Hi Lee,.

  The long wait has its result.

  Seems that it's a typo. Engineering has responded that it is supported.

  Let me know if you encounter other problems.

• Driver RAID for Vmware ESXi 5.1 on Dell R420.

  My project is to install Vmware ESXi 5.1 on a Dell R420 with Raid1 configuration. The question I have after configuring raid1 in raid utility is created using the, I launch the installation of Vmware ESXi 5.1. What is ESXi 5.1 sees not the raid1 partition but rather see two disks as are they worn can't in raid1 configurations.

  I need to have this in raid1 config, can any who share an idea about my problem please or point me in the right direction.

  I did some research but nothing seems to help resolve this issue.

  Thank you

  Sheriff.

  Sorry for my previous response:

  DELL-Daniel My - when I boot in the BIOS of the controller, I see the raid in a raid1 configuration.

  Mgr dev you are right, I did research more when you all answered. I see the PERC S110 pilot was a software raid controller and thus the vmware esxi wouldn't work in a raid configuration 1 (software raid).

  Thank you guys for you answer and who helped me

• SDK can not connect to the Simulator in VMware

  My operating system: Windows 7 64-bit

  SDK version: 10.0.9; Build id: v201212072306

  VMware Player Version: 5.0.1 build-894247

  Video card: NVIDIA GTX 560 Ti

  I'm trying to use the simulator of 10 BlackBerry, running in VMware Player, to test applications under development in the native BlackBerry SDK. However, when I try to run these applications from the SDK and connect to the Simulator, I see that even though (I think) I got the correctly configured IP address for the target, it is still listed as "Not connected" in the list of Options of the target (I don't know if this is normal or not). Then, if I try to launch the project in any case, I get the following error message:

  "Unable to connect. Make sure USB cable or Wi - Fi is connected, the IP address is correct, and the mode of development. »

  Sorry if I didn't explain very clearly, this is very new to me, and I still have trouble getting my head around it. I'm sure there is probably some information that I forgot to include in this post, but I will provide if I think that whatever it is.

  I have been looking for solutions to the question, but it seems that there could be many possible causes, so I thought it would be better to make a new thread specifically for my situation. I tried the following:

  -Check that the development Mode has been activated (it seems that it has been enabled by default)

  -Ping I thought several times, was the IP address of the command line simulator (sometimes I had to meet with success, but not at the beginning)
  -Disabling Windows Firewall
  -Running a .bat file with 'ipconfig/release; ipconfig / renew. ipconfig/flushdns ".
  -I check the correct target for the Simulator IP address (double-check this confuses me a little, but I think I can find it in "Settings"-> "About" simulation-> 'Network' menu?)
  -Temporarily disable Avast! antivirus software to check if she is interfering
  -Verification of VMware Windows were running (I think he installed four of them in total)
  -Uninstall (then reboot) and reinstall the SDK, Simulator and VMware and restarting, repeatedly

  -Windows asked to troubleshoot the connection of VMnet8 of VMware; He said DHCP must be enabled, but then failed to do this for me (this left me confused; I wasn't sure if it was important or not)

  -Passage of the NAT VMware Bridged mode for the simulator mode, then the connectivity test (it doesn't seem to help, and the "About"-> page 'Network' in the simulation was empty), then power back up

  Any help or any what pointers to additional information, I would give, would be greatly appreciated. Thank you!

  EDIT: I also cant seem to get QML previews to work at all. I don't know if it is related to my other question, but I thought it might be worth mentioning, and this is something else I would try to fix, if possible. I tried to update my drivers, but to no avail.

  Solution found! I just tried to add a target in the software development kit using the IP address on 'Settings' of the Simulator-> "About"-> "Network" screen, but the target has been filtered out of the list, unless I unchecked "target filter based on the selection of C/C++ applications". If I unchecked, the target has been classified as ' 192.168.31.128 (Neutrino / x 86) ', but the Run button was grayed out when I chose it and I noticed the error message, ' binary Selected target do not match x 86 "at the top of the window." I have googled this error message and found the following (quite old) thread:

  http://supportforums.BlackBerry.com/T5/native-development/QNX-IDE-target-selected-binary-and-target-...

  After reading through and testing, it turns out that all I had to do was change the active configuration in the drop-down list at the top of the window SDK 'Device-Debug' for 'Simulator-Debug", little"hammer"that I needed to build to the Simulator and not a real physical BlackBerry device. Here is a quote from the post of cdamus, which is where I found the solution:

  "A little trick to streamline your workflow: prospects for development C/C++ has a little"hammer"toolbar of action that you can pull down (click on the black triangle next to it) to define and build the active configuration in one step, for one or several projects."  The icon to the right (it looks a bit like a sundial) defines the active configuration, but is not build. »

  I took a screenshot to help indicate the setting that I need to use:

  

  Hope this helps you chuma and anyone else who has this problem. Thanks for the tip, cdamus!

• VMware ESXi 5.5 - System Board SEL_FULLNESS 0... 100 unknown

  Hello community,

  I'm going to have that kind of alarm on VMware ESXi 5.5 - SEL_FULLNESS system board 0...

  How to solve this problem?

  vmware_logs.PNG

  

  Greetings.

  You want to connect to your MMIC and clear log SALT.

  Fullness SALT refers to full journal SALT is.

  The journal SALT allows only a certain number of entries before becoming full.

  Thank you

  Kirk...

• Requirement of the graphics card dedicated for BB10 simulator

  Hi, the blackvery website developer, I found the infromation that BB10 Simulator requires NVIDIA GeForce 8800 GT or higher to an ATI Radeon HD 2600 or higher graphic. This affects when even if the pc has the graphics card integrated rather than required. I mean I can run the Simulator very well, but this will affect anyway if I run an opengl project in the Simulator? Thank you.

  The BlackBerry 10 Dev Alpha Simulator uses OpenGL 2.0.  If your graphics card does not support it you can have problems (some only show a black screen).

  If you see a black screen you can try the software rendering mode (choose option 2 before boots simulator), but you could still see some rendering issues using this mode.  In addition, it is going to be slower.

• To install Vmware Esxi 4 on PowerEdge 2800

  Hello. I have a PowerEdge 2800. I wanted to install Esxi 4.

  I download the OM_6.5.0_SMTD_A0.iso and the server starts on the DVD. When I choose install Vmware Esxi 4.0, it asks me to insert the CD / DVD with. But when I insert the DVD the Vmware I download refuses to recognize. Please help me solve the problem. I even tried to install windows server 2008, he refuses.

  Tank you.

  I saw the solution.

  I was supposed to download "VMware-VMvisor-install". Dell_Customized.ISO' to 'http://ftp.dell.com/esg%20solutions/ '.

  Tank you.

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.