BBM BBM voice - can not hear each other for the first 5 seconds

Similar Questions

• How can I recover my pc for the first time that I bought?

  Hello
  How can I recover my pc for the first time that I bought? because my pc is so slow... I have a compaq laptop cq61... and I want to set up the first time... How can I?  I don't have a recovery disk because when I bought it dosnt have a recovery in it disc. Please help me. Thank you

  Hello

  I'm happy to help you

  Glancing at the screen shot you posted, your looks of partition fine recovery (recovery (D).

  Save your files on an external hard drive or flash drive (depending on how many you have).

  Once that is done, disconnect all connected to your PC, but the AC adapter.

  Start the PC and the HP welcome screen, press the F11 key to start the Recovery dialog box and follow the prompts.

  It should take 15 to 30 minutes and your PC needs to be restored to its factory settings.

  Then just reinstall all programs and files that does not come with the PC.

  You will need the files or the installation of program diskettes. You cannot back up installed programs and reinstall them using a backup.

  Paul

• Computers can't see each other after the installation of E3000

  I found several previous posts about my question, but none of them have led me to a solution to my problem. Here's my problem. I have a small home network that I could share files and printers on now I bought for and install a Cisco E3000 and my computers do not see each other. My current configurations is as such: I use DSL and you have an ADSL modem to 2 wires with wireless capabilities. This particular modem has a port for the telephone line and a local Ethernet port. I took the local ethernet and plugged into the internet port of the E3000. All computers can access the internet, but they cannot see. I checked that the file sharing and printers is enabled on all computers. In fact, if I remove the E3000 of configuration and place them on the 2wire wireless connection they see each other. So I'm pretty sure that the firewall on each PC software will allow file and printer sharing. Which leads me to believe that my problem is in the E3000. It blocks perhaps the Protocol of network discovery or something. Does anyone have ideas how I can fix this problem? Any help is appreciated.

  Well, I solved the problem by returning the router to the retailer and Exchange to another router. Now, all network shares working. Consider the problem solved.

  (Mod Note: under the guidance of the compliance of the directive.) (Thank you.)

• can not read each message in the Inbox via firefox

  As of this morning, the Mar, 04/26/11, I can go to my Inbox, see all messages list it but can not read each email so that I can access via Firefox.  By clicking on each entry as usual, 'javascript' appear in the lower left corner, just above button start.  I have no problem reading through Explorer.  What have I done?

  Hello

  Try the procedure described in the following KB article

  http://support.Mozilla.com/en-us/KB/troubleshooting%20extensions%20and%20themes

  For more information, post your queries in instances of Firefox. Here is the link

  http://support.Mozilla.com/en-us/home

• can I send my hearing cc work for the first cc 2015 2015?

  Hello

  I know I can send an audio clip to edit in the hearing of first cc,

  but I can start working on a clip and send to audticion cc for the first

  I have two sub, w10 pro 64-bit

  Thank you

  Go to multitrack and select export to Adobe Premiere Pro.

• Windows 7 Home premium network problem, computers can access the internet, but they do not see each other on the network

  I was trying to set up a homegroup on my main computer, but on the second computer, I never had the opportunity to join the homegroup. I'm sure that I have everything set up properly, but I can't get the second computer to join.

  I have a switch that my internet runs and a cat cable goes to each computer. Each computer can access the internet without any problem, but none appear in other network list. They have the same name of working group, I just can't understand it. I use Windows Firewall.

  Any help would be greatly appreciated.

  Maybe this can help.

  ----------------------

  Win7 when configured on the peer-to-peer network has three types of configurations of sharing.

  Group residential network = only works between Win 7 computers. This type of configuration, it is very easy to entry level users to start sharing network.

  Working network = fundamentally similar to previous methods of sharing that allow you to control what, how and to whom the records would be shared with.
  
  Public share = network Public (as Internet Café) in order to reduce security risks.

  For the best newspaper of the results of each computer screen system and together all computers on a network of the same name, while each computer has its own unique name.

  http://www.ezlan.NET/Win7/net_name.jpg

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ------------------------------

  If your network consists only of Win 7 and you want a simple network, use it.

  http://Windows.Microsoft.com/en-us/Windows7/help/videos/sharing-files-with-HomeGroup

  After you have configured the homegroup, scroll to the bottom for the Permission/security section.

  -----------------------------

  Win 7 networking with other version of Windows as a work network.

  In the center of the network, by clicking on the type of network opens the window to the right.

  Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.

  http://www.ezlan.NET/Win7/net_type.jpg

  Win 7 - http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows

  Win 7 network sharing folder specific work - http://www.onecomputerguy.com/windows7/windows7_sharing.htm

  Vista file and printer sharing - http://technet.microsoft.com/en-us/library/bb727037.aspx

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040
  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP - http://support.microsoft.com/kb/875357
  Windows XP Patch for sharing with Vista (no need for XP - SP3) - http://support.microsoft.com/kb/922120

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  -------------

  If you have authorization and security problems, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  * Note . There must be specific users. All means all users who already have an account now as users. This does not mean everyone who feel they would like to connect.

  ---------------------

  *** Note. Some of the processes described above are made sake not for Windows, but to compensate for different routers and how their firmware works and stores information about computers that are networked.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Bought a HP15 g009AX but can not find a driver for the graphics card

  Hello

  I bought a model of flipkart HP15 g009ax a week, but I can't find any drivers, I istalled Windows 7 64 bit. The problems that I face are below:

  (1) find the driver for the graphics card Ati amd 8570 M cant

  (2) among the three USB ports work alone

  (3) cannot turn down the brightness of the screen

  I tried both links but below its still does not not for me.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=7101...

  and

  www.PCIDatabase.com

  Help, please.

  OK... time to be creative, and I think it will work...

  We will manually install the graphics driver W8.1 your model use.

  Use the following steps to manually install the graphics driver...

  Run this graphics driver W8.1...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-135683-1&cc=us&DLC=en&LC=en&OS=4158&product=7255430&sw_lang=

  Go to Device Manager and click to expand the category graphics cards.  Click on the VGA Standard card.

  Click on the driver tab, click on set to update driver.  Select her browse my computer for driver software option and navigate to the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp67327.

  Make sure that the include subfolders is selected and the driver should install.

  Reset.

• Can not load CD software for the printer 101-707 error code, what to do?

  New printer Kodak ESP C315 and I can't install the software.

  Hello

  What operating system do you use?

  I suggest to perform the clean boot and try to install the software.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  I would also ask that you contact the manufacture of your printer.

  http://resources.kodak.com/support/PDF/en/manuals/urg01243/C315_AiO_xUG_GLB_en.PDF

  http://support.en.kodak.co.UK/app/answers/detail/A_ID/31819/kW/101-707/session/L3RpbWUvMTMyMDY0ODIxMS9zaWQvYmNQNV91SWs%3D%2Fselected%2Ftrue/selected/true

• Can not find XP drivers for the WIFI and its computer HP G71-449WM laptop

  Hi guys, I tried to downgrade a HP G71-449WM laptop to XP Pro SP3 so far I have everything except the WIFI and sound. I tried all the drivers on the Xp Downgrade Guide wifi but none doesn't seem to work, I tried to search the Win7 drivers to see if I could at least identify what brand it is (Intel, Broadcom, Atheros, etc.), but it lists no WIFI Drivers on the Support page. All ideas are welcome.

  I think you'll Atheros, but not 100% on that. Atheros seems to be giving XP downgraders, grief most right now... with the sp42654 listed in guide with the highest success rate at present.

  HWInfo32 are trying to see if he can id wireless here

• way that I can not receive or aply for the alert announcement provided by Windows Live Messenger

  It does not apply to the alert in the Messenger section because apparently we did not take this facility in Australia?

  Hi MirthaMarti,

  I recommend you post your question in the Windows Live Solution Center for assistance.

  Portal Messenger

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer

• I can not DreamWeaver of installation for the free trial version.

  I get to the initialization of the box install then he disappears, and DW does not open. The installation program does not appear in my list of applications either.

  uninstall all cc

  clean through the use of the Adobe Creative Cloud cleaning tool to solve installation problems

  Restart your computer

  install the application of office cc, https://creative.adobe.com/products/creative-cloud

  Use the desktop application to install your tests.

• Premiere Pro CC - effect audio Denoiser works is not on the first few seconds of the clip

  I use the audio Denoiser effect for the main audio track. When I export and play the video, the Denoiser effect is disabled for the first few seconds of the clip. I read on other forums that this can be corrected by putting the effect on the faucet of the audio track instead of each individual clip, but I already tried this and it does not solve the problem. Any ideas?

  audio denoiser appears to use the adaptive method by default. in other words, need a few seconds to look at the material to build a profile of noise and then start removing the noise. This is useful for when the noise pattern changes during recording. If you try to remove the noise is constant, you can open the effect and check the box 'freeze' to have keep the noise profile. This can make the effect kick in instantly vs seconds.

• OAM 11 g SSO: receiving error OAMAGENT-02027 on each connection after the first

  I'm using the ASDK 11 g to connect to a server (11.1.1.5) OAM 11g. We have the configured server and SSO work and we can see that it works for the first user to connect. However, after that sign first, everyone else cause the following exception occurs:
  "oracle.security.am.asdk.AccessException: OAMAGENT-02027: Oracle AccessGate API is not initialized."
  
  Whenever authenticate us the user, the following steps are processed:
  
  -Get the session token
  -Create a new default instance of AccessClient with the given configuration directory and 10g CompatibilityMode [ac = AccessClient.createDefaultInstance (OAM_CONFIGURATION, AccessClient.CompatibilityMode.OAM_10G)];
  -Create a new UserSession object with the token and the access generated access client
  -The information required of the UserSession object
  -Stop the instance of AccessClient
  
  
  On the first invocation, it rolls and the user is brought to our application after the default login page and that they are correctly recorded in our system. Connect the other errors on 'create a new object UserSession... '. "step shown above with the above exception.
  
  If someone has encountered this error and know how to fix? Or have any suggestions about how to try to determine what is the problem?
  
  Thank you
  
  [EDIT]
  Fixed the title, this isn't a server OAM 11 g, 10 g.
  
  Edited by: mBaldwin on 8 March 2013 13:42

  The new g 11 API differs a lot in terms of how the ASDK is initialized. In 10g, you would initialize the ASDK for each application, however, 11 g, you just launch the ASDK once at startup and then use it again to stop.

• social voice for 64-bit Windows 7 chat can not hear the other person in Windows Live Messenger.

  Hi I am running windows 7 ultimate 64-bit and every time I try to chat with friends on the mic, I can not hear them, but they can hear me, all other sounds on my pc are working properly and not voice chat, ive got all my drivers updated and no idea how to solve this problem, thanks

  Hi snake1121,

   
  It seems that there is a problem with the settings of Windows live messenger.
  We recommend you to ask a question to Windows Live Messenger Forums for assistance.
  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• 6.18: others can not hear me after a minute of a call on Skype versions 6 and higher

  I went back to version 5.10.0.116 as for versions 6 and upwards, I can't talk. After about a minute of a call, I hear others without a problem, but they can not hear me or hear me in staccato (and it's the same for calls to Skype-to-Skype and Skype for phone calls). My computer runs on Windows 7, I have Norton internet security. I checked and re-checked the firewall settings and Skype is on his list. And I did it for each new edition of Skype 6 and higher version, as I had the same problem with all of them. Messaging works very well.

  Now, I received the message that the 5.10 version is removed... If I can't fix the problem with the version 6, I will not be able to use Skype, which is great annoying.

  Hey kerojarun,

  I join the diagnostic file, still do not have have a chance to make headlines. The attachment is a zip file containing the diagnostic log. I had to rename it to jpg, Portal refused to tie it as a zip, saying that the type of file did not match the extension.

  Regarding the log files, do I understand correctly that you would need to log version 6.18, not those of version 5.10 I currently use?