Similar Questions

• Difference between VI and executable execution.

  I have a dynamic number of buttons in a cluster that I position by program on my front screen based on the upper-left position of the bunch.  When running in development mode, everything is fine and the cluster remained in this post after the execution.  However, when the application is built, the buttons and the cluster flowing to the left in a phased manner.  I have attached the source zip file.

  I think the solution is very simple and it would have been more obvious except for the fact that you 'hid' the offending code using a stacked sequence (please, never use a stacked sequence).

  In the box "invisible" 0 and 2 cases of the sequence stacked, you write to the scripting property AutoSize.  Run mode, this property is a read-only property.  In general, any property node with the light blue colour which designates a property Scripting, are (probably) not in the code that is planned for the construction as an executable file.

  Bob Schor

• Mapping data between BI and another Oracle module

  Hello
  
  I'm working on a project for a Government of a county of Florida. We have a problem with project accounting R12 data match with OBIEE 11g database. It is more of a field of marking problem than a problem of integrity of data - for example, 'Customer number' in the accounting of the project is clearly a different data set than 'Customer number' in BI. We know the same data exists in BI but we do not know what it is called and therefore how interrogate him for reporting purposes. Why data marking is so messed up, I can't say, but I was in charge of mapping 'Customer number' (and everything else) in project accounting to the equivalent of the BI field. Supposedly this mapping does not already exist (which seems impossible since someone set up the flow of data between the two parts of the system at some point!). I hope someone can recommend an approach that doesn't end up being heavy and manual. Thank you!
  
  Warm greetings to all,
  
  John

  https://support.us.Oracle.com/OIP/faces/secure/km/DocumentDisplay.JSPX?ID=1274680.1#BODYTEXT

  OR

  Oracle Business Intelligence Applications ETL Data Lineage Guide version 7.9.6.2 and 7.9.6.3 [ID 1274680.1]

  Check this box... It gives you a document of data lineage... Mapping between source and target stage and...

  It certainly helps you the way that you look.

  MAK is useful if it helps...

  Kind regards
  Rayan Vieira

• Fact Eve DataGuard between (Source site) 11.2.0.3.0 and (target site) 11.2.0.4.0 taken in charge?

  Hello gurus

  Fact Eve DataGuard between (Source site) 11.2.0.3.0 and (target site) 11.2.0.4.0 taken in charge?

  My environment:

  Site source OS: RHEL 5.6 Database: v11.2.0.3.0

  Target site OS: RHEL 7.1 Database: v11.2.0.4.0

  The database size is 100 GB

  What about

  Hitgon

  As I mentioned, again the DG transport and apply the will to work in mixed versions. But it is not supported by Oracle for longer period. When I say not supported which means lets say if you hit any bugs in mixed environment associated with DG, then you can't get a support to connect to a new bug... etc... However, mixed versions are supported bby Oralce for 30 days. This is because any time the migration/upgrade that you can keep primary and standby in different versions.

  For more details refer,

  1.

  search for lines,

  The maximum length supported for different database software house between primary and Nightlight is 31 days.

  Insurance of Patch Oracle - Data Guard standby-first Patch applied (Doc ID 1265700.1)

  2. with regard to Cloud Control Support.

  SUBJECT: Set up and manage Oracle DataGuard, using Oracle Enterprise Manager Cloud control 12 c

  search for "the obligation for the Oracle software is stricter. The Oracle software must be the same version - including the release of the patches Oracle group. »

  Set up and manage to Oracle Data Guard with Oracle Enterprise Manager Cloud control 12 c

• Program LabVIEW will hang between 33% and 50% of the time.

  I have a problem with a Labview program, I did. I have two programs that do the same thing. One is as a flat sequence, and the other is in the form of State machine.

  As explained in the link below, I would like to use a microcontroller to perform wiring for automation of a measurement process. A separate current source and volt meter will be used.

  https://forums.NI.com/T5/LabVIEW/sequence-a-good-idea/TD-p/2601333

  I did some simple test programs that I join since then. The problem is when running, that the labview program crashes, but not all the time is to run the program.

  For example: Hall 1.2.vi will correctly work twice with the third time, he is executed, it crashes. If Cancel you and try again, it will run again twice without any problem with the third hanging. It is in the flat sequence format (was in a flat sequence, but merged windows because I thought that was the cause). From what I can tell, the program crashes when calling Keithley 6517 unique Read.vi. Two connected Keithley devices are connected to the computer via GPIB to 16 and 27. The way I checked if it was this vi the cause or contributed to what I deleted the program never hung and it. I find it very strange that it crashes exactly on the third attempt every time.

  Simple.VI Hall 1.3 will work the first time and hang the second time. If it works 50% of the time. It is in the format of State Machine. It hangs in the case entitled "Measurement 1" that contains the Keithley 6517 unique Read.vi.

  I used the running highlight button and watched the program to run. Curiously, it only crashes when you use this button. So I tried to add some delays/waiting in different places without success.

  This could be the cause? As a side note, I say that the program is suspended for two reasons. The principal is the program does not run so the execution arrow is always black. The second thing is that if you notice at the end of the labview program, I have a block he who turns to the power source which does not happen when it crashes. I have to turn it off manually, and then click the abort program button to stop labview.

  
  

• Edit event managed by this case in LabVIEW 2013 does not show the specifiers of the event, Event Sources and events on screen resolution 800 x 600

  Edit event managed by this case in LabVIEW 2013 shows not specifiers of the event, Event Sources and events on screen resolution 800 x 600.

  As far as I know, the list of supported resolutions is determined solely by the graphics card. It is possible that one used by the PC supports only 800 x 600 as maximum resolution, even if you plug an external monitor.

  Like Dennis suggested, the recommended option would probably be to develop on another PC and only deploy an executable for the industrial PC. That's what we do with our systems (although not because of this problem, but because it makes sense. There absolutely no need to have the IDE installed in most of our systems).

  Other options:

  1. See if you can get an update of the driver from the manufacturer to solve this problem.
  2. Plug a USB Monitor with its own driver.
  3. Try to hide the taskbar and make the smaller title bar in the hope that the bug manifests.
  4. Try remote access in the PC. I think that some remote access programs allow you to specify custom resolutions that are not affected by the original drivers. Remote Desktop seems to be a likely this option even if it has been awhile since I've used it.
  5. Check the BIOS. I saw at least one industrial PC where there was some settings in the BIOS to control the resolution, but I don't remember the details, and it was quite limited. I think that in this case, you can change the resolution, but then the image does not fill the entire screen.

• Is there a link between Simulink and Multisim?

  Is it possible to start a design in Simulink and the circuit design and the Board of Directors using Multisim and Ultiboard?

  Does anyone do this?

  Andrew,

  There is no direct translator between Multisim and Simulink tools. A few things would be possible:
  1. If you have designed your control algorithm there is some control blocks in Multisim. The are located under the Sources-> control function blocks. Try to see if you can replicate the Simulink functions in Multisim.
  2. There are several function transfer blocks available in Multisim. There is a good example under the option menu to open samples that will show you the diversity of the blocks available in Multisim transfer function, that can be able to describe the system-level blocks that you implement in Simulink.

  I hope this will give you an advance.

  Kind regards
  N Pat

• Cache objects VI shared between 32 and 64 bit?

  Transferred into the LAVA: http://lavag.org/topic/16349-vi-object-cache-shared-between-32-and-64-bit/page__pid__99898

  I am currently working on a major project that is to be deployed in 32 - bit and 64-bit flavors. This means that I must periodically switch between installed versions of LV to build.

  It * seems * that if I work in 32-bit BT, and then I close and re-open my project in 64-bit BT, that everything needs to recompile... even if I had only changed a few things since the last, I worked in 64-bit.

  It seems that while LV keeps a Cache of objects VI separate for each version of LV, that it does NOT keep a cache separate for 32-bit versions and 64-bit. Is this really the case?

  Fabric Hello,

  LabVIEW maintain separate caches for versions 32-bit and 64-bit of the same version, but in the same file. They are separate entries in the objFileDB. Because 32-bit and 64-bit are very different beasts, the project must be recompiled in order to adapt to the new platform every time that you open in a new environment. It is possible to separate the compiled source code code. Research in the other forum posts, this separation likely to cause a higher risk of corruption VI.

  Best,

  tannerite

• Mutual redistribution between EIGRP and BGP and match statements

  Hello Experts

  I'm working on a problem of mutual redistribution between EIGRP and BGP

  The idea is a beacon (210) on traffic from our LAN on R2 - 2 so that it can be put in correspondence and denied the R3-7. The goal is to prevent routing loops.

  The routes are redistributed in R1 - 1, but I am not able to see if the roads are being marked.

  Can someone let me know how to check the roads are being filtered with course maps?

  TBH, I don't think the market at all.

  I have attached the configs and view orders.

  I read somewhere the problem was with match type internal route command, but I don't know if this is the problem

  Any help will be greatly appreciated.

  Topology and configs are attached.

  See you soon

  Hello

  You have 2 points:

  1. Deny the redistribution of EIGRP routes tag in BGP: you already have with your route map
  2. You must filter the roads scholar eigrp on R5 to them are not propagated in R2. I'll use a roadmap for the tag and the EIGRP neighbor. The configuration looks like:

  IP access-list standard FROM_R4
  license to host 192.168.1.2
  !
  !
  EIGRP-TAG route map deny 10
  ! subnets from R4 with tag 210
  match ip route-source FROM_SLDC
  game tag 210
  EIGRP-TAG allowed 20 route map
  !
  Router eigrp 65100
  ! Filtering of marked routes
  route map EIGRP-distribute-list tag in
  !

  Currently, you are missing a piece to import these networks R5.

  Thank you

  PS: Please do not forget to rate and score as correct answer if this answered your question

• Problem with IPsec VPN between ASA and router Cisco - ping is not response

  Hello

  I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

  my network topology data:

  LAN 1 connect ASA - 1 (inside the LAN)

  PC - 10.0.1.3 255.255.255.0 10.0.1.1

  ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

  -----------------------------------------------------------------

  ASA - 1 Connect (LAN outide) R1

  ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

  R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

  ---------------------------------------------------------------------

  R1 R2 to connect

  R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

  R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

  R2 for lan connection 2

  --------------------------------------------------------------------

  R2 to connect LAN2

  R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

  PC - 10.0.2.3 255.255.255.0 10.0.2.1

  ASA configuration:

  1 GigabitEthernet interface
  nameif inside
  security-level 100
  IP 10.0.1.1 255.255.255.0
  no downtime
  interface GigabitEthernet 0
  nameif outside
  security-level 0
  IP 172.30.1.2 255.255.255.252
  no downtime
  Route outside 0.0.0.0 0.0.0.0 172.30.1.1

  ------------------------------------------------------------

  access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
  object obj LAN
  subnet 10.0.1.0 255.255.255.0
  object obj remote network
  10.0.2.0 subnet 255.255.255.0
  NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

  -----------------------------------------------------------
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 3600
  Crypto ikev1 allow outside
  crypto isakmp identity address

  ------------------------------------------------------------
  tunnel-group 172.30.2.2 type ipsec-l2l
  tunnel-group 172.30.2.2 ipsec-attributes
  IKEv1 pre-shared-key cisco123
  Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

  -------------------------------------------------------------
  card crypto ASA1VPN 10 is the LAN1 to LAN2 address
  card crypto ASA1VPN 10 set peer 172.30.2.2
  card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
  card crypto ASA1VPN set 10 security-association life seconds 3600
  ASA1VPN interface card crypto outside

  R2 configuration:

  interface fastEthernet 0/0
  IP 10.0.2.1 255.255.255.0
  no downtime
  interface fastEthernet 0/1
  IP 172.30.2.2 255.255.255.252
  no downtime

  -----------------------------------------------------

  router RIP
  version 2
  Network 10.0.2.0
  network 172.30.2.0

  ------------------------------------------------------
  access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
  access-list 102 permit esp 172.30.1.2 host 172.30.2.2
  access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
  interface fastEthernet 0/1
  IP access-group 102 to

  ------------------------------------------------------
  crypto ISAKMP policy 110
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 42300

  ------------------------------------------------------
  ISAKMP crypto key cisco123 address 172.30.1.2

  -----------------------------------------------------
  Crypto ipsec transform-set esp - aes 128 R2TS

  ------------------------------------------------------

  access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

  ------------------------------------------------------

  R2VPN 10 ipsec-isakmp crypto map
  match address 101
  defined by peer 172.30.1.2
  PFS Group1 Set
  R2TS transformation game
  86400 seconds, life of security association set
  interface fastEthernet 0/1
  card crypto R2VPN

  I don't know what the problem

  Thank you

  If the RIP is not absolutely necessary for you, try adding the default route to R2:

  IP route 0.0.0.0 0.0.0.0 172.16.2.1

  If you want to use RIP much, add permissions ACL 102:

  access-list 102 permit udp any any eq 520

• AD, used as a trusted source and target system

  Hello

  I have a requirement to use AD as a trusted source and the target system the zero days and 1 for a transitional period.  We have 18 applications to integrate with OAM for SSO.  Currently, the authentication and authorization of these applications are made via AD.  However, the client wants to move to the use of LDAP in goal SSO.  The first phase includes 3 apps on the 18 apps.

  Day zero, I use AD as a source of confidence to push users to IOM.  Then, I run AD as a target system to link the user to their existing AD accounts.  Their ad groups will also be reconciled by IOM.

  Because there will be a transition period and the customer would not have to change the process of assistance to creating accounts AD (for internal and external users), they asked that we continue to allow accounts AD to reconcile with IOM in the trusted source and target system.

  I have not used AD connector as a reliable source.  I intend to source AD done trust reconciliation to run first, then the task of reconciliation system AD target to run then.  It's the same AD connector.

  This can work as long as the customer wishes until they want to spend to IOM for the creation of the user and accounts AD commissioning through the access policy.

  Is this sound ok you?  There is a "witch hunt" I didn't think?

  Thank you

  Khanh

  Yes, you can run the recon trust first and get all the identity created by IOM.

  Later, you can run the Scheduler for recon target for linking AD accounts with user profile of IOM.

  Note: There is a field in AD IT resource in need of update if you want to switch between the target and recon trust.

  Research of configuration:

  This parameter contains the name of the lookup definition that stores configuration information used during the reconciliation and commissioning.

  If you have set your target system as a resource target, then enter Lookup.Configuration.ActiveDirectory.

  If you have set your target system as a reliable source, then enter Lookup.Configuration.ActiveDirectory.Trusted.

  Default value: Lookup.Configuration.ActiveDirectory

  ~ J

• Source and program monitors crashing in the first

  Hey all.

  So, unfortunately I seem to have problems of stability with Adobe Premiere CC 2015 (to date).

  The source files are H.264 in a .mov container.

  I am running Windows 10 but have experienced the same problem yesterday in Windows 7.

  I use the EMT.

  So here's the deal. I was running really slow and repeated performance crashing (just the program monitor and source and also of the whole program). I was pulling my hair out with frustration and decided to pull the trigger on a new computer. (Yes, I know... the upgrade to solve problems of crash was probably not the best idea, especially without the problem of the first widely).

  My old computer:

  Windows 7

  AMD Athlon II X 4 630 @ 2.8 ghz

  12 GB OF RAM

  NVIDIA GTX 460 768 GB

  New computer:

  Windows 10

  Intel i7 4790 @ 3.6 ghz

  24 GB RAM

  NVIDIA GT 720 1 GB (the OEM mobo dislikes my GTX 460 [known issue] and I plan to get a GTX 960 or GTX 970 tomorrow)

  I've been editing, completely blown away by how smooth first and After Effects were running; a pleasure to scrub through the timeline in PP and time real AE RAM previews. Then, just before you go home at night, the program and the source monitor crashed.

  On my old computer, it meant that they became black. On the new computer they're going grey (sometimes the source monitor panel displays "media forward"). On both computers, the playhead moves and audio isn't yet.

  I do not regret my upgrade, I know that it was overdue. However, it is a bit disheartening that I expected the upgrade of instability to do a thing of the past (I do not claim that it was smart thinking lol).

  Any input would be greatly appreciated.

  PS. After the program monitor and the source of watching the crash, the program does not freeze. I tried switching back and forth between Composite and Mulitcam (in the program monitor) or Composite and Audio Waveform (in the Source monitor Panel) to try to jog it in work and that does not work. On the old computer, when I was finally closed PP to relaunch a dialogue accident would seem, but not up to what I chose to close the program to reboot (little strange, right?). On the new computer, the only time where he arrived so far (less than 90 minutes to play in the first), it didn't pop up with a dialog to crash, it just closed as usual. I don't remember if the dialog crash on the old computer had an error code.

  Change the name of mov to mpeg extension and see if it will help.

  I'm not upgrading to W10 and have no problem with the nikon files and cc15. I'm a little skeptical W10.

• Color change of values between Illustrator and InDesign

  I have googled and looked here for an answer to my question, but have not been able to find anything.

  I designed several pieces of encumbered asset, all using the same unique color. Some of the pieces I designed in Illustrator and the other in InDesign.

  The problem is, when I copy and paste the yellow color value (if it is RGB or CMYK - I tried both ways), it CHANGES between Illustrator and InDesign. The color stays the same between Illustrator documents, but if I C + P InDesign - or vice versa-, the color value change literally before my eyes. And I don't want to say 'looks like' different, real changes in number.

  Here's a real example:

  Call a box in Illustrator and chose the color #f8f1e0 / 2% 3% 12% 0%. Call a box in InDesign, C + P had the values of color in there, and it DID change the color appropriate for a moment. You click OK. Click New in the color picker and color is now #f8f1e1 / 2% 3% 11% 0%.

  If it is relevant, it seems that the color will change to a slightly darker every time.

  And Yes, the two documents has STARTED OUT as CMYK documents and stayed like that. I also have my color sync via Bridge. I'm working on CC 2015 and all programs are up to date.

  Any idea of what could happen? Thank you in advance.

  ETA: Okay, I just chose preview overprinting in Illustrator and also changed the color of #f8f1e0 to #f8f1e1. I see now this is not a malfunction of the program, but can someone explain WHY this happens? I'm still new to color management and it's quite confusing for me. Thank you once again.

  ETA: thing: when I save the InDesign document to readable PDF and then pull it in Illustrator, the color is now #f8f2e2, even when you preview overprinting.

  Hexadecimal values are RGB color, so if you plug one in the color chart the resulting CMYK values are a conversion of the color management of the profile the document CMYK document RGB profile. You will get different CMYK conversions according to the profile source RGB, CMYK destination profile, intend to color and compensation of the black point used for the conversion.

  In addition the InDesign documents can have colors RGB and CMYK with CMYK and RGB profiles assigned that do not necessarily correspond to the color settings work profiles, in order to sync'ng your color settings may not get everything to match.

  Ultimately if you want to match the CMYK color or nuances between AI and ID, make sure you document assigned CMYK profile matching (Edit > assign profile...) and enter CMYK and hex does not values

• How to communicate between ExtendScript and basic generator

  I run a separate node server as described in this tutorial to create a plugin with generator-core. http://tomkrcha.com/?p=3896

  I'm in a situation where I need to send a lot of JS to photoshop via generator.evaluateJSXString (). But it can easily become uncontrollable that you can send a string. So, for any complicated feature, it becomes difficult to maintain. Is it possible set a bunch of functions in a script to measure file and then call these functions from the application node?

  So I could send:

  generator.evaluateJSXString ('doSomeStuff ()');

  And in a script somewhere (I don't know where this script should go)

  I have the defined function that can do something

  function doSomeStuff() {}

  for (var i = 0; i < 10; i ++) {}

  doc.artLayers.add ();

  }

  }

  Where the Script to extend file would in this case? OR is there a better way to make this kind of thing.

  Just a mixed collection of thoughts:

  • Yes, you can package scripts in the form of .jsx files (also jsxbin if you prefer not to share the source) and run with generator.evaluateJSXFile (path), which will work even in ESTK. It has some limitations
    • It is just a file that runs, that is not this function 'call '. I managed this by dividing my Javascript libraries and plugins (= this a function). Can I use Gulp to concatenate libraries necessary for each plugin to create scripts of jsx 20 + that I call the two panels of node & Photoshop
    • There is no parameter passing, but it can be overcome by the presence of a script (that you run a string) parameter store (or fetch result) to Photoshop as a descriptor of persistent custom action
  • The plugin folder where your main.js is accessible by Node.js variable '__dirname '.
  • Depending on how you use paths, you should consider Windows "------" vs. Mac ' / '.
  • Another good way of communication between the panels of Photoshop and the node is a Web server in the configuration node and use Ajax/jQuery in Panel of Photoshop. You can do ~ 500ms update on election and get feedback from Panel pretty real time.

• vMotion between E5630 and e7540

  Hi all

  We can after activating the CVS vMotion between models of the following processors:

  Between

  Processor Intel Xeon E5630
  

  &
  

  Intel Xeon E7540

  
  

  
  

  Between

  Processor Intel Xeon E5630

  &

  Processor Intel Xeon E5640

  
  

  I went through the VCA compatibility chart but I don't understand it. Help, please.

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & docTypeID = DT_KB_1_1 & externalId = 1003212

  New features in each generation of processor. However in order to migrate live virtual computer, the CPU characteristics presented to the virtual machine must be equal on the source and target host does not cause problems (such as BSOD). The different EVC baselines hide or reveal certain CPU features to the virtual machines that are common for all processors in the cluster. Table 1.1 in the article you mentioned some of these CPU features.

  André