Black screen before loading windows

Similar Questions

• XP won't boot up - just a blank black screen before "Newspapers Windows" appears.

  I hooked up another hard drive and allowed the error checking in the tools to check it out when you restart.  That's when it started.  When I remove the player, all right.  There are actually 2 discs and they both have the same problem I only activated this control on one of them.  So obviously the problem is not hardware.  I could check with various utilities and everything was fine.  I can't imagine THAT XP has a 2 TB disks problem dealing with.  I should also mention that previously used on Linux.

  Any ideas anyone?  Anywhere to check to disable this check on restart thing?

  So I got 2 hard drives, leaving only drive C with XP and 2 new readers.  It started fine.  I added everything else and it restarted correctly.  Another mystery of Windows.

  I always want to know if I can boot from a microSD card in a typical card reader.

• Given to nine Compaq 7700, BSoD, boot XP infinite loop, can't even get past the black screen to enter Windows. STOP: 0X0000007E (0XC0000005, 0XF773B15F, 0XF78D2520, 0XF78D221C)

  Help.

  I just got a refurbished Compaq 7700. It has Windows XP for drives of the refurbished computers.

  I try to boot from the hard drive (HD) and infinite loops, it is never past the initial home screen (black with blue status bar).

  I can't open the safe or the HD mode, it freezes at kmxstart.sys and then restarts again.

  Original title: given to nine Compaq 7700, BSoD, boot XP infinite loop, can't even get past the black screen, to enter Windows.

  I tried to boot from the disk and created Windows appears, then load the files, but then automatically tries to start Windows (without repair option). It then jumps to the BSoD with error code (after advice to verify sufficient disk space, to disable the driver identified, to change video cards, BIOS updates...)

  STOP: 0X0000007E (0XC0000005, 0XF773B15F, 0XF78D2520, 0XF78D221C)

  Usbccgp.sys - address F773B15F base at F7737000, DateStamp 480254d 2

  Apparently, this driver is a printer driver? I don't have a printer, but do not know how to disable it without access to windows.

  I got a new Philips 18.5 "monitor, an optical mouse and a keyboard with it.

  My guess is that the screen is the problem, because it was full again when I received and therefore not tested with the system before shipping. Not sure about the mouse and the keyboard.

  I tried a few options in the BIOS screen as well, but no dice.

  Help! Before shipping the brand new...

  I thank you and have a wonderful new year.

  Craig.

  Howdy Daavee and Shekhar,

  I hope that your day is going well.

  It turns out that it was the hard drive, it was defective. The new unit arrived and it works beautifully. Thank you very much for all you help. I wish you a happy new year.

  Craig.

• Start window manager: sometimes when I started my PC I have a black screen with the Windows boot manager at the top.

  Sometimes when I start my PC I have a black screen with the Windows boot manager at the top.  Although there are several options available, that nothing happens no matter what keys I hit and the only option is to shut down the computer and restart completely.  Sometimes the Boot Manager page turns and my office sometimes opens fine.  I've updated with everything Microsoft has Windows Vista and I still get this screen.  Anyone has any ideas.

  Do a startup repair and see if that fixes it:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Screen is frozen with a black screen with blue windows logo on it.

  Original title: problem of Windows 8

  I just bought windows 8 and is now downloaded and installed. But it seems that my pic froze or something because for about 2 hours now it is stuck on a black screen with blue windows logo on it. After research, I found a video and in this screen in a minute or two! Anyone know anything about this? I need ASAP thank you!

• Windows XP Home, black screen after loading screen (seemingly unique problem)

  Hi all

  I am trying to upgrade to service pack 3 Windows XP home on my old computer from eMachines T2838 and experiences a @# *! a time to do it. This is the third time in 2 days I had to wipe my HD and re - install XP, because of some problem installing updates which has damaged the operating system.

  Here's my current situation.

  Yesterday, after the failure of the HD for the second time (computer got stuck "performing cleanup" on SP2, forced a reboot, got a restart loop after, would not load Windows) I installed XP, update to SP2, then downloaded the service pack real itself. He has installed fine and asked me to restart.  I respected that, and the computer restarted. As soon as the "Loading" screen popped up, I knew that something had gone wrong.  When I started on the desk, I was stuck in 640 x 480 w / 4 - bit color graphics mode. Could not be set. So, I thought, okay, let me reboot Windows and see if he "rediscovered" the integrated video card. Well, I restarted, and the "loading screen jumped into the appropriate color mode / resolution, so I thought that I was in the green."  Well, after that, all I get is a black screen. No message 'No signal!' or anything like that.  Even tried a few instructors that I have. Looked around online, has seen the references to "Last known good Configuration" 'safe Mode' etc etc.

  I tried all the options on the list of F8. Either she freezes at Mup.sys xxxxxx or boots up to the loading screen and then goes black after. I can hear the HDD does it's thing for a bit, so I don't know it is loading this screen "check to activate the automatic updates" which appears after SP2 is installed, but I can't.

  Use the recovery console, (did the repair option the first time after it kept restarting, Windows took 5 minutes to start an IE6 get locked every opening, so had to wipe and re-install) typed "chkdsk/p/r" and he did his thing for about 30 minutes, rebooted and still have the same problem.

  I don't know what else to do. I REALLY want to redo everything this a fourth time, only to to have screw it up once again, and I don't know how many times I can use the key I have on the back of the computer.  (Using a retail disk and an OEM key, Finder product key changer.) -A Microsoft Support Officer showed me that one. Quite handy.

  People do you have any suggestions?  I would really appreciate it.

  Hello

  Try the steps listed in the link below and check if it will help: computer stops responding with a black screen when you start Windows XP: http://support.microsoft.com/kb/314503

• black screen that activate Windows.Windows must be enabled before validation to determine whether this copy of Windows is genuine.

  I am writing on behalf of my friend who has had his computer for a while with no problems. Today, it starts up to a black screen and then you had this message

  Windows must be activated prior to validation to determine whether this copy of Windows is genuine.
  Windows is in reduced functionality mode.

  It runs windows vista edition Home premium and it is authentic. However, it doesn't have a disc.

  can help you as he declares that he has 30 days!

  Hello

  1. is your friend able to boot to the desktop?

  2 are there hardware/software changes made on the computer, before the show?

  To analyze and solve problems for Activation and Validation, we need to see a full copy of the report produced by the MGADiag tool

  a. download and save the desktop tool

  http://go.Microsoft.com/fwlink/?LinkId=52012

  b. Once registered, run the tool.

  c. click on the continue button, which will produce the report.

  d. Paste the contents of the report in this thread.

  See also,

  How to contact a Microsoft Product Activation Center by phone

  Resolve activation problems

• XPS 8700 - black screen before you get to the screen of Windows 7. Help please.

  Hello. I recently bought 8700 XPS, replaced the 550W PSU and video card MSI GTX 660.

  The problem I have is the booting takes too long, almost 2 minutes. I see the screen black for about 1 minute before it goes to the screen of Windows 7.

  I updated the driver vga for later and others through dell system detects as well.

  What should I do to get rid of the black screen and reduce startup time?

  Boot in the Bios F2. Go to start. Boot USB support is set to disabled? If not, change it to disabled. Press F10 to exit the Bios and reboot.

• HP 500-046: 6 beeps at startup, can't access boot options (black screen) but then Windows loads ok

  After making a system image backup I wanted to test the recovery disc. To start from the cd tried to change bios to disable secure boot and enable legacy startup.  Could not get the pc to boot once so reset cmos by shorting the pins on the mboard.  Now to start always get 6 beeps and black screen, but after a minute, windows login screen lights up and it works fine.  Unable to access the bios Setup screen any key used at startup.  6 beeps indicates a video card problem, but no material error in device mgr points.  Want to update to Win 10, but unsure about do to address this problem starting.  Appreciate any help.

  @JohnN59,

  Thanks for the information to know.

  You can try the DVI port on the motherboard

  I/o Ports and internal connectors

  Rear i/o ports

  Figure: IO back panel

  

  1. USB 2.0: 2

  2. Output S/PDIF port optical

  3. VGA

  4. DVI - D

  5. LAN

  6. USB 2.0: 2

  7. USB 3.0: 2

  8. Audio: Port of central/subwoofer (yellow-orange)

  9. Audio: Rear Speaker Out port (black)

  10. Audio: Side Speaker Out port (gray)

  11. Audio: Line (light blue) port

  12. Audio: Output line port (lime)

  13. Audio: Microphone (Pink) Port

  If is not shows the start then try the Bios reset/recovery (windows + B key).

  Please keep me updated.

• Pavilion dv6-6047 cl: black screen before opening of session in Windows 10

  Recently, I upgraded my laptop Pavilion dv6-6047 cl of Windows 7-64 bit for Windows 10-64 bit. The only thing I changed from the original specification (see link below), it is that I bought a Samsung SSD 850 EVO 500 GB. In Windows 7, everything was fine, the boot to make up to 8 sec. Now she starts, but stay for more than one minute, stuck in a black screen for the login screen to appear.
  I tried to update the graphics driver, but nothing happened.

  The processor driver is up-to-date.

  The SSD driver is too far.

  I rolled back to Windows 7 and everything went back to normal. And then upgraded to Windows 10 once again, everything goes black again.
  Please help me, because my SSD is worthless with a + 1 minute boot.

  Thanks in advance!

  Link to the original spec: http://support.hp.com/us-en/product/HP-Pavilion-dv6-6000-Entertainment-Notebook-PC-series/5048664/mo...

  Link to the product page: http://support.hp.com/us-en/product/HP-Pavilion-dv6-6000-Entertainment-Notebook-PC-series/5048664/mo...

  I solved it! I disabled ULPS as a result of this http://www.tomshardware.co.uk/faq/id-1904869/disable-ulps-amd-crossfire-setups.html . All is well now! This is the quick start again!

• Black screen on startup - Windows 7 Professional

  I recently installed Windows 7 Professional on my laptop MSI, 4 GB of RAM, processor Intel (r) Core (TM) 2 Duo CPU, 32-bit operating system, Nvidia GeForce 9600 m GT 512 MB.

  When I turn it on, there is all black screen. I pull the battery (until I discovered F8) and it starts in safe mode with network. Then, I reboot safe mode and windows load correctly. Two days before the blackout, the cursor would freeze too.

  Note I've read related topics, like the one in which it is suggested to disable the graphics drivers, and I recently downloaded new ones from Nvidia, but it started two or three days later, so I doubt it has to do with the graphics drivers.

  Should I try with the system restore or perhaps reinstall Windows?

  Yesterday, I found and installed both updates Optional:

  1 Realtek driver update for Realtek PCIe GBE Family Controller

  2 update for Windows 7 (KB976422)

  In any case, this morning, the windows loading straight, so with this optional support, the problem could be solved. I hope that nothing will change in the future, however.

• On Qosmio G30 black screen after installing Windows XP

  Hello world
  I want you help me solve my problem.
  I have a Qosmio G30E - 148 and when you install a new program, the BSOD had been posted. prevents me from having access to windows from
  normal mode and safe mode.
  Then I installed a new Win XP manually and when trying to install the screen to black color display (nvidia geforce go 7600) driver and I turn it off
  safe mode in order to use windows.
  Another favor, I need a driver for ethernet controller and multimedia video controller because I can't find them.

  Thank you for all.

  Hello

  I have several question for you:

  -What system was installed before? Windows Vista?
  -where you have downloaded the display driver? On the Toshiba site?
  -You can find all the necessary drivers in the section download the drivers on the Toshiba site-> http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU
  Simply choose XP MCE as an operating system, the drivers are the same as XPPro/XP

  Hope I could help, if you have additional questions just ask. :)

  Greetings

• Black screen T400 with windows xp

  a friend of mine gave me his Lenovo T400 to install Windows XP on it

  He previously worked fine with windows 7 and 8.1

  then it starts in preinstallation of windows XP screen, it formats the hard drive and as usual instalation automatically restarts after this BUT his black screen, lights and sounds show that it works and goes to the next screen BUT the screen is still black. Put power off then turn on again does not display any image of the screen. Open he removed the battery of the Bios, turned upward after a few pennies and turned off it starts it reset the bios.

  So now it has photo and it goes on the next screen Windows instalation as usual, after the installation of devices and other things, it restarts automatically as usual BUT there is NO new screen, black screen, lights and sounds new show that its loading windows end instalation screen, but no image on the screen.

  Reset the BIOS again, it starts normally, and this time shows BSoD with code 0x7B, after once again the BSOD screen black

  Maybe it's a setting in the BIOS? tried to install with the AHCI drivers and tried to install without driver for Compatible, what else is there? Updated the bios to the latest version, same result.

  To say again - it works very well with other windows, but XP should be installed

  There is a manual for installing XP on these laptops, I have not read, sorry

  so the black screen is because of the switchable graphics option in the Bios that is not supported by XP

  It works fine now after a whole an integrated and disabled for OS detection framework

• black screen appears in windows movie maker

  My windows Movie Maker allows to work properly, I have windows vista, but this last year, when creating and previewing my film but nothing black screen appear instead of my movie... Don't know what happened. Even if idon't preview I will burn the dvd and then play on my dvd player and I still get the image black all through the film I've done. I tried to change all the filters in any way diff but no luck. I can't get any help from anyone. Help!

  Maybe... I want to say just maybe you would have a
  best result with and older version of Movie Maker.

  No guarantee but the next for an installable download
  version of Vista Movie Maker 6 may be worth a try

  * Proceed at your own risk *.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  Windows Movie Maker Installer for Windows 7
  http://noeld.com/programs.asp?cat=video#wmminst

  Also, Movie Maker 2.6 will work on Windows 7:

  Windows Movie Maker 2.6
  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&id=34
  (this is similar to the version of Win XP Movie Maker 2.1)

• Black screen after using Windows Memory Diagnostic

  Recently I have experienced problems with the system restore doesn't work don't not and although perhaps it was the file system and so I started Windows Memory Diagnostic and didn't know that you need to manually restart the computer and so I tried works again and again until what it finally hit me that I needed to restart it myself. He began to do his thing and I left a little to return to a black screen at 3:30 and it is now 23:00 and still nothing has changed. Don't know what to do and I don't want anything corrupt or damage my computer anyway. Is it normal for her and if not, how can I stop my computer safely?

  Hi Brendan,

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  This problem may occur because of corrupted display driver.

  I suggest you use the steps in this article and check if it helps.

  Reference:
  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Important notes:
  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you