Blue Screen iastor.sys, STOP; 0x0000008E (0xC0000005, 0x828490B8, 0xB96DA758, 0x00000000)

Similar Questions

• Blue screen and error code: 0x0000008E (0xC0000005, 0x8243BA8D, 0xE3452BB4, 0x00000000) _

  I get the above error message and bluescreen when the computer is just sitting idle does nothing.  Usually, it's when the internet is open, but not surf.  Can someone help me understand this.  The graphics card is an Intel 82945 G express shipset family and I checked to see if it is up-to-date and the pilot said he is up to date.

  Any help?

  Hello

  Have you checked Site system manufacturer (manufacturer of custom systems motherboard), then
  Intel downloads?

  After checking the system manufacturer's Site

  Intel - Downloads - graphical value and then the other parameters as needed.
  http://Downloadcenter.Intel.com/

  ===========================================================

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  --------------------------------------------------------------------------------------------------------------

  Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
  Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
  other pilots to check there. Disable the installation of self as those who are older and if
  Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

  See methods of update driver generic in the next message.

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
  * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens. (If necessary)
  
  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  It comes to my convenience store generic bluescreen:

  Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
  This would help. Such as ITC and 4 others entered at the bottom left. And another error
  information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Blue screen... STOP: 0x0000008E (0xC0000005, 0xBF8B6C11, 0xA9538368, 0x00000000) win32k.sys - address BF8B6C11 base address BF800000 DateStamp 4C7d06ce

  I have a Dimension 3000 bought in 2005, upgraded to 2 GB of RAM.

  I recently implemented almost from scratch, because Opera program and profile would be repeatedly corrupted, making me lose the email. (This reappeared even after reinstall opera clean, do not use old messages or other profile files). Therefore, I restored a backup of the C: partition Ghost (there are others for my data and downloads) I did shortly after the purchase, after which I had installed only Ghost and two games (I uninstalled the games). I installed SP3 and ran Microsoft Update. I was trying to reinstall other programs that I use now. It's Rhapsody; one of my kids 'synchronize' a player MP3 Sansa Fuze with Rhapsody.

  A few days ago when closing Internet Explorer, I got a message that should be closed and I could send a report to Microsoft. It is also used to happen before, from time to time.

  Then, more recently, when I closed Rhapsody, I got a blue screen with a message that there was a problem. He said I could try to change some settings in the BIOS. I remember what happens before I restored the ghost of 2005 BU. I looked in the BIOS and not able to find the parameters referred to in (something like memory cache). I wish it were possible to print these messages on a blue screen. I didn't copy the entire message, but I write these references:

  STOP: 0X0000008E (0XC0000005, 0XBF8B6C11, 0XA9538368, 0X00000000)

  Win32k.sys - address BF8B6C11 base address BF800000 DateStamp 4C7d06ce

  This means almost nothing to me. I hope that someone on the forum knows what this means and can suggest what could be the problem.

  So far, I have not had more wrong with Opera, so there may be two distinct problems. OTOH, I reinstalled only Opera on 10/12/10; I can still have problems with it.
  

  Hello

  Here is more information on the bug 0x8E control: http://support.microsoft.com/kb/945658/

  The 0x8E KERNEL_MODE_EXCEPTION_NOT_HANDLED can be caused by a faulty service/driver, damaged hard drive or defective display card not enough space, or memory, Hardware/software incompatibility and third-party remote control software. So to get started:

  1. test your memory. Run Memtest you can download from http://www.memtest.org/#downiso. Download the ZIP file, extract the ISO and write on CD. Once written to CD, boot your PC with the CD and run Memtest. Allow the test to run by at least 3 passes or until it gives errors. If you have more than 1 memory module, run the test on each module separately. Try running Memtest from a cold - start unplug your PC for an hour to cool down, then immediately run memtest again when you next turn on the. This way memtest will run when the memory is cool and after the 3rd pass when the memory is hottest.

  2. update your display driver. Reference Dell seems to have highlighted 3 different models of Dimension 3000 and so there is 3 different Intel display drivers. See if you can find an updated driver on the Intel Web site. If you use a graphics add-on card try to find an updated driver from the manufacturer's website. If you have any trouble finding a driver let us know what brand and model of graphics card you have.

  3. update the Rhapsody software. (I think it's the software you using http://www.rhapsody.com/-software ?). If it's Rhapsody software I think it seems to integrate into your Web browser and it's perhaps why Opera and now IE are mistakes? You can uninstall Rhapsody for a while just to see if it is the reason for your BSOD.

  4. when the 0x8E BSOD is caused by win32k.sys, yours, is it then possible, it is caused by control software remote third. It can include programs such as VNC, PCAnywhere, etc. of Teamviewer, RAdmin.  If you use one of these programs, uninstall it and see if the PC stops mistakes.

  5 run a scan on your hard drive. You can check your hard disk for errors by going toStart ->Run -> type chkdsk c: /r -> clickOk . When asked if you want to force a sayNodisassembly. When asked to plan the audit at the next startup, Yes. Reboot your PC to allow running chkdsk.

  Alternatively, you can run a diagnostic on your hard drive. This by downloading the diagnostic program from your hard disk manufacturer. A list of manufacturers and their diagnostic tools can be found here: http://www.tacktech.com/display.cfm?ttid=287. Once more, download the ZIP file, extract the ISO and write to CD. A time written on CD, boot your PC with the CD and run the test Advanced/extended.

  Also make sure you have enough hard disk space. It is always recommended, if possible, to have at least 15% of your free hard disk capacity.

  6. Finally, take a look in your event viewer when the BSOD for possible errors. You want to look especially in the system and Application logs (and maybe Internet Explorer connects). You can run Event Viewer by going toStart ->Run -> type eventvwr.msc -> pressOk -> event viewer screen opens. If there are errors listed in one of the newspapers type them in your next post if you are not right.

  Reading your post I see 3 specific issues, that you might want to focus:

  -The memory you added (run Memtest) and hard drive (run Chkdsk)

  -The Rhapsody program - try to update or uninstall.

  -The software was initially corrupted until you make the first image after the purchase. So you just ghost the problem on.

  I hope this helps. Good luck.

• STOP: 0x0000008E (0xC0000005, 0xBF9568C8, 0xA6864C00, 0x00000000) win32k.sys - address BF9568C8 base at BF800000, Date stamp 4ff2f633

  Hi, I get a blue screen frequently with the below error message.
  "Technical information:
  A problem has been detected and windows has shut down to prevent damage to your computer.
  
  
  STOP: 0X0000008E (0XC0000005, 0XBF9568C8, 0XA6864C00, 0X00000000)
  Win32k.sys - address BF9568C8 base at BF800000, Date stamp 4ff2f633
  
  
  Beginning physical memory dump.
  Complete physical memory dump.
  For more assistance, contact your system administrator or technical support.  "
  I am using Packard bell Easynote MX45.
  XP Home edition Version 2002
  SP3
  Inter (R) CPU [email protected] GHz.
  3 GB Ram
  could someone help me fix it please.

  N

  You are better able to tell us if the problem is resolved.  Continue to run Malwarebytes about once a week.  If the BSOD ceased and MBAM does not show any other infection, you're probably good.

• I get the blue screen error - error - Stop 0X0000008E

  -Stop error 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000)

  Hi I get the blue screen error - error - Stop 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000) and cannot use the pc in safe mode. I have XP - OS. I really don't want to reformat the HARD drive and you want to avoid reinstalling as much as possible

  Hi aromaveda,

  ·         Have you made changes on the computer?

  Follow these methods.

  Method 1: Follow the steps in the article.

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article to check the drive for errors.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

• STOP: 0X0000008E (0XC0000005, 0X805662D1, 0XB38CDA04, 0X00000000)

  Tonight, my computer shuts down with a blue screen with a message saying that there was a problem with Windows, more this stop message...

  STOP: 0X0000008E (0XC0000005, 0X805662D1, 0XB38CDA04, 0X00000000)

  I have managed to restart in Mode safe for this post, but am not all that computer warned to manage a technical difficulty.   Is there a simple solution that I can use for this problem, or is a trip to my computer that required doctor?

  I have not loaded new software in the past few days and have now uninstalled the latest program installed, just in case.

  When I tried to send an error report, it wouldn't send it due to a problem.

  Any ideas?

  Thanks in advance,

  Andrea

  It can help to look at the files minidump against accidents with a debugger.

  Can you zip the minidump in the C:\Windows\Minidump folder files and (provide link) available via Windows Live SkyDrive or similar site?

  The following link has information about the use of Windows Live SkyDrive:

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  If you have problems to compress the minidump files copy the minidump files to another location such as a folder on the desktop

  In addition, you do not necessarily have compress the minidump files, you can download one at a time.

• Stop: 0x0000008E (0xC0000005, 0x805678A0, 0xEDE28CA8, 0x00000000)

  I was browsing the internet and nowhere a blue screen appeared in front of me and this displays exactly:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or check manufacturer updates the driver. Try changing video cards.

  Check with the hardware vendor for updates to the BIOS. Disable the BIOS memory options such as implementing caching or shading.

  Stop: 0x0000008E (0xC0000005, 0x805678A0, 0xEDE28CA8, 0x00000000)

  Followed by the physical memory dump. Now at this point, I don't know what to do or think. I don't know what this means, but if someone could enlighten me and walking I would be grateful. Where can I find and locate the devices or equipment having problems?

  Hello

  Follow the steps in the link below and check if you are able to solve: general troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E": http://support.microsoft.com/kb/945658

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to fix error iastor.sys stop: 0x0000008E on my dell m1330

  I got a bsod stop: 0x0000008E error iastor.sys

  After that I inserted a usb flash drive. I restarted and got safe mode start upward.

  in normal mode it restarts after 2 minutes. When in SafeMode its ok.

  I already ran a registry cleaner but did ' t help.

  I am currently in safe mode to find help.

  Do not use Registry cleaners, they will make things worse. And it will not solve this prob.

  Scan your system with an anti-virus. If the flash drive is bootable put this on and then run it. Or run it in safe mode / networking

• STOP 0X0000008E (0XC0000005, 0X8062E1D3, 0XF8AC34B0, 0X00000000)

  I got a bluescreen with this message/code as seen in the title.

  1. What does that mean?
  2. What can I do about it?

  Hi Carrillo23,

  1. Once you get the error message?

  2. did you of recent changes on the computer?

   

  See the Microsoft article and try the steps mentioned below.

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Blue Screen error message stop 0x000000d1 (0xb86bcb9b8, 0x00000002, 0xfd90112, 0x00000000) driver irql not less or equal

  Computer won't start all the way to the top, gets there where you choose the login name, and goes to the screen.  Will start in mode without failure but need to make impression.  Have not made any changes to the hardware or the software.  Ran virus scans, nothing was found.

  Hello SMS47,.

  As you can start in safe mode, I would like to try to perform the clean boot troubleshooting.

  Please use the following link and follow the instructions:

  How to configure Windows XP to start in a "clean boot" State

  Let us know the results after taking these measures.

  Best regards

  Matthew_Ha

• Blue screen * STOP: 0x0000008E (0xc0000005, 0x00000000, 0x8BB32B66, 0xB6F93F6C) * iaStor.sys - address 8BB32B66 base at 8BAF1000, Datestamp 4a7c1b38

  I have a Hewlett-Packard HP ProBook 4510 s 32-bit with Windows 7 Home Premium and a blue screen appears always * STOP: 0x0000008E (0xc0000005, 0x00000000, 0x8BB32B66, 0xB6F93F6C) * iaStor.sys - address 8BB32B66 base at 8BAF1000, Datestamp 4a7c1b38

  Hello

  Check with the help of HP, their online documentation and drivers, diagnostics and ask
  in their forums about known issues with this model.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  =======================================================

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ===============================================================
  
  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Two main causes of these blue screen video drivers and BIOS - check with the system manufacturer
  Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
  other pilots to check there. Disable the installation of self as those who are older and if
  Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

  See the methods of update driver generic and verify the implementation of driver verifier in the next
  Message.

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.

  • 0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  Make sure you have enough disk space.

  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
  * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• __ERROR PHYSICAL DUMP MEMORY __STOP 0X0000008E (0XC0000005, 0XBF05D7EE, 0XECE00BC0, 0X00000000)

  WHEN I OPENED MORE THAN 2 TABS WATCHING YOUTUBE OR VIDEO SITES, A SCREEN BLUE WILL SHOW SAYING THAT PHYSICAL MEMORY DUMP... STOP STOP 0X0000008E (0XC0000005, 0XBF05D7EE, 0XECE00BC0, 0X00000000)

  Hi ferds11ab2001,

  Follow the methods below:

  Method 1:

  Disconnect all external devices (printers, scanner, USB (universal serial bus) drives, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Method 2:

  Follow the steps mentioned in the articles below which deals with a similar question

  1. General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"http://support.microsoft.com/kb/945658

  2. you receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000).

  I have error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000). I did the F9 Diagnostics and no error found. Also, I tried to remove the DVD and replace the video card, but no improvement. However, Windows starts normally in SafeMode only. Thanks for supporting.

  Product ID: 89578-OEM-7332157-00061

  Hello

  Specifying your version of Windows and other information would help help us to you.

  How to ask a question
  http://support.Microsoft.com/kb/555375

  -----------------------------------------------------------------------------------------------------------------

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ===============================================================
  
  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Two main causes of these blue screen video drivers and BIOS - check with the system manufacturer
  Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
  other pilots to check there. Disable the installation of self as those who are older and if
  Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

  See the methods of update driver generic and verify the implementation of driver verifier in the next
  Message.

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.

  • 0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  Make sure you have enough disk space.

  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
  * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Blue screen of death: stop error: 0X000000CE

  Hi, I think I got a bad virus on my computer that's all waste.  First of all, it all started when I clicked on a link, while the Christmas on Black Friday shopping. Then I got a download of unwanted software, called system difficulty, (the small icon of Windows) I could not use system restore to remove, whenever I tried to use it, it says cannot restore on this point. Tried several other points, but no joy. Can I get the dreaded blue screen of death with a stop error: 0x0000008e (0xc0000005, 0x804f8e80, 0xef76aa98, 0x00000000). Could sail in safe mode and tried to fix it with antivirus software, found 26, abducted, ran spybot search and destroy, found nothing. Still no joy. So today, I tried to start in safe mode, and it does not work in safe mode, guard reboot again and again. Then I hit F8 and turned restart turned off so I could see the Blue error screen that would flash for just a second, and now I have this stop error message: 0x000000ce (0xf88be6dc, 0 x 00000000, 0 x 00000000, 0xf88be6dc). I read forums on video and all drivers, but this happened just after I clicked on this link and got the virus with this unwanted software download. Anyone got any suggestions on how to solve this problem? Oh and I downloaded a program called error repair of my other computer and installed but it only scan my computer to find errors and then he wants to buy you the pack premium, so that did not help. It's my computer business running windows xp pro service pack 3. Wish it would have been on this cause she has the system recovery and it worked whenever I had a virus, I couldn't get rid of that. Thank you, Steve

  JoseIbarra is the expert resident on the Recovery Console and chkdsk/r. I'll track down his instructions. If the malware is responsible for the BSOD, I do not think that chkdsk /r will help, but it won't hurt. Or you might need to repair your boot.ini file.

  DEFINITELY get this brand XP reinstallation CD Dell! You can use it to perform a clean installation of XP or a repair installation of XP (chances are, you won't ever need to perform a repair installation, but it is nice to have this option) or to enter the Recovery Console to perform functions such as chkdsk/r.
  Chances are that your data does not fit on one CD! Depending on what you have, you might need to up to 100 CDs or more! Better to buy an external hard drive. Newegg.com has a very good selection of the most affordable. Here is an example:
  http://www.Newegg.com/product/product.aspx?item=N82E16822148409
  Creating a Ubuntu CD bootable 'live' (and then startup out of it, rather than on your hard drive) will allow you to copy your data to the external hard drive:
  https://help.Ubuntu.com/community/LiveCD
  There are also some other CD bootable antivirus (like Avira) which may help you:
  http://www.livecdlist.com/purpose/Windows-antivirus
  Here is a link to the instructions of Jose:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-system/unmountable-boot-volume-stop-0x0000000ed/570c7f90-5869-E011-8dfc-68b599b31bf5

• Blue Screen Atapi.sys - continues to come on start up...

  I got this blue screen Atapi.sys

  Address F8568256 base at F8560000 datestamp 4802539d

  I had that before. I don't understand that I solved it, but it was a headache and I don't remember what I did.

  The fact that I get it every few months is a stressful thought.

  Can anyone help?

  I scanned my computer and nothing comes up as a virus. Maybe this isn't picking up. I'm not sure. If this is the case, how I remove it manually if it is a virus?

  The atapi.sys (or mechanism) is known to be a target of malware, so I'd start here:

  Your system boots very well?

  Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, MSE, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  To eliminate the questions and riddles, please provide additional information on your system.

  Click Start, run and enter in the box:

  Msinfo32

  Click on OK and when the system info summary appears, click on Edition, select all, copy, and then paste the information here.

  There will be some personal information (such as the user name and the name of the system), and anything that turns information private for you, simply delete the pasted information.

  Perform scans for malware, and then fix any problems:

  Download, install, update and do a full scan with these free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/

  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/.

  They can be uninstalled later if you wish.

  If you get the blue screen of death, we need more information, and here's how:

  Download BlueScreenView here:

  http://www.NirSoft.NET/utils/blue_screen_view.html

  Unzip it and run it (BSV installs nothing) and let him complete the digitization of all of your files to dump.

  If you double-click on depressed, you will get information on it (including the field caused by the driver) and you should be able to spot the problem right away - especially if you see a model in landfills where Caused by field pilot is the same (beginning with this driver).

  Select (highlight) one or more of the most recent dump files by clicking on them and hold down the CTRL key to select multiple files.  Try to select only the most recent links that relate to your problem (perhaps five or six to start dump files).

  Click on file, save selected items and save information from the dumps to a text file on your desktop called BSOD.txt.  Open BSOD.txt with a text editor, copy the text and paste it in your next reply.

  Here is an example of the report since a single BSOD BSV I initiated on purpose that indicates the cause of the accident as the pilot i8042prt.sys belonging to Microsoft Corporation:

  ==================================================

  Dump file: Mini062110 - 01.dmp

  Crash time: 21/06/2010-11:51:31

  Bug Check String: MANUALLY_INITIATED_CRASH

  Bug check code: 0x000000e2

  Parameter 1: 0x00000000

  Parameter 2: 0x00000000

  Parameter 3: 0x00000000

  Parameter 4: 0x00000000

  Caused by the driver: i8042prt.sys

  Caused by the address: i8042prt.sys + 27fb

  Description of the file: i8042 Port driver

  Product name: Microsoft® Windows® Operating System

  Company: Microsoft Corporation

  File version: 5.1.2600.5512 (xpsp.080413 - 2108)

  Processor: 32-bit

  Computer name:

  Full path: C:\WINDOWS\minidump\Mini062110-01.dmp

  ==================================================

  Please vote my posts as helpful so I can get a lot of points. I'm saving for a pony! Everybody don't like Raymond.