Bluetooth headset ear cushion to replace 820 HT

Similar Questions

• firmware for the iPhone bluetooth headset original work with the 5s iPhone

  Hello to our community,

  I have a beautiful original apple iPhone Bluetooth Headset model n °: A1221

  This helmet does not work correctly.

  When I connect the headphones to the computer (iMac 27 "mid-2011, el Capitan 10.11.3) with the original Headset USB travel cable, headset LED is bright orange and the LED color changes to green after a few minutes.

  When I disconnect the headset no lights are bright and the headphones does not work.

  After charging more then 1 hour the same answer.

  When I put the headset with the USB cable connected in my ear, I can hear the sound signal very low volume of pitch high e. When I push and hold the button of the headset tone is stronger.

  When I disconnect the cable, the helmet is instantly dead, no lights, no sound, nothing happens when I push the button on the short headset, for a second, four seconds, 10 seconds or even longer.

  Is there a possibility to reset? A new firmware? An Exchange program? Any help?

  Max

  The helmet has been abandoned, I think that 2009. So, it's long after the warranty. BT headsets have come a long way since then. The Apple headset does support A2DP, now standard. I he write off and buy something current.

• Cliq: Bluetooth stereo-ear audio cutting

  I recently bought a Sony DR-BT100CX bluetooth stereo-ear put to use with my Cliq. No problem matching the device, it connects right up. I use mostly the reader integrated music and Pandora in 3G.

  Problem is every 5 to 30 seconds music shuts down for about a second.

  I used the wired headset previously with the Cliq and the same apps, no problem. I also tested the Atria bluetooth with streaming music from my desktop computer and there are no drops audio (even at 15 feet away).

  The Cliq is in my pants pocket, and the BT receiver is in my coat ~ 1 ft away. I tried to disable wifi/wifi-loc/gps/gprs, battery mode performance setting, killed all other running applications, update to the new 1.1.41. liberation and disabled profile HFP (phone) for headphones on the Cliq - but nothing has helped.

  Drops audio seem to occur a little more with Pandora music player integrated, but because it runs a network and off-network application... I don't think it's gprs. My hunch is that what the cause is in the bluetooth stack, but I do not know how to continue the investigation.

  you know I think it was after the put 1.1.31 updated the 'leap' began to arrive. I use my headset for when im on my computer. I just combine my BT comps with the helmet and it works fine. its got to be the update.

• BlackBerry Smartphones Bluetooth headset

  I can answer is no longer a call only from my Plantronic Bluetooth headset.  I have to respond on the BB, then choose either 'forward the call to handset' or «continue with Bluetooth»  This has just begun.  I can't find a setting to route the call automatically to my helmet.  And it sounds no longer on my helmet.  Any ideas?

  Hello and welcome to the community!

  Each time a random strange behavior or slowness comes, the first thing to try is a proper reboot:

  • With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes.

  See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.

  Good luck!

• Œuvres of 'stereo' Bluetooth headset, but 'hands-free' is not

  I can't connect my Plantronics 590 headset with my Win7 Home Premium SP1 system in hands-free mode.

  Details: in the window "My Bluetooth" for this headset: (1) I push the Connect button next to the heading "calls of VoIP before handsfree.  (2) upwards in the header bar, it shows "status: connected, the Signal level: high", and down into the "hands-free" it the topic shows «Connecting to 00:19:7F:38:F0:79 hands-free...» ", but then (3) after 5-10 seconds it shows, at the top," status: paired ' and the section free hands, "the connection failed".

  I can connect this headset in ' stereo '.  But of course the headset does nothing in this mode. Details: In the same window, (1) I press the connect button next to the title of "listening to music". (2) upwards in the header bar, as in the previous case, it shows "status: connected, the Signal level: high", and headed down under the "hands-free" he shows «connecting to 00:19:7F:38:F0:79 hands free...» ».  (3) in less than a second, it shows connected to 00:19:7F:38:F0:79 stereo Audio Device".

  Another thing I notice is that when I push the button 'My Bluetooth settings' on the home window "My Bluetooth", nothing happens.

  Let me add that this headset works very well (in both modes) on my other computer that is running Windows XP Pro SP3.  And I'm sure that it worked in hands-free mode on the Win 7 in the past - I have not tried to use it with the Win7 system for several months, until now.

  ~ Thanks in advance for your help
  ~ Ken

  I am pleased to announce a minor miracle that solved my problem.

  Just after I posted this query, I got a little popup (Microsoft, I guess) that said, it did not have something wrong with my Bluetooth drivers and offers to replace them.  I followed the instructions.  I do not understand what this little gremlin has gone to fix things to the top.  But the main thing is that my Bluetooth hands-free headset working again!

  Initially, I assumed that the timing of this popup was just a coincidence.  But upon reflection, it seems more likely that Windows was able to detect my repeated unsuccessful to connect my hands-free gadget and finally decided to take pity on me.

  Anyway, anyone or whatever it was that I got up and running again, thanks!

  ~ Ken

• Can I connect the watch or Bluetooth headset at the same time?

  The watch or Bluetooth headset (maybe a pair of the Airpod) connect at the same time?

  I have iPhone 6 now and will update to 7 earlier.

  I do it all the time with my iPhone 6. I assume you mean to plug the headphones into the iPhone, right? Whatever it is, you can connect to the phone or watch.

• How to use a Bluetooth headset to make phone by Apple Watch call?

  My question:

  my iPhone is on the platform to the floor. I'm in the garden, away from my iPhone, outside of the coverage of bluetooth. However, I'm on my WiFi network so my Apple Watch is connected to my iPhone via WiFi.

  I get a phone call on my iPhone at home and my rings Apple Watch on my wrist in the garden. I answer with the watch, but I would like to continue the conversation by using my bluetooth headsets, which are associated with my Apple Watch...

  Is there a way to do this? As far as I can see, bluetooth headsets can be paired with Apple Watch to listen music stored Apple Watch...

  Tnxs.

  Hello

  It is not possible to use a Bluetooth headset that is associated with Apple Watch in order to pass or receive phone calls.

• Pairing Bluetooth headset with Apple Watch 2 series?

  Hoping that someone here has some good ideas, so I can avoid having to go through the centre commercial/Apple Store!

  Bought a watch series 2 the day of the launch, immediately tried to pair with the bluetooth headphoens I got (AvierBTE somethings). No luck. Thought maybe I just got bad headphones - but they always associate with my iphone 6 s. bought a pair of Mswift Pow helmet off Amazon and bluetooth headset at the same time borrowed a friend this pair with its original Apple Watch. My Mswifts, or his headphones will pair with my watch, although the two pair with my iphone.

  My watch IS pair with my amazon echo - so I know the bluetooth works.

  The watch is the headset in discovery mode, but when I try to pair, it gives an error and says it cannot associate, check that the camera is turned on, in range, etc..

  Another person had problems of this kind and has managed to find a solution?

  Hello

  Make sure that you follow the instructions for pairing here:

  Use the Bluetooth with your Apple Watch - Apple Support Accessories

  It can help to turn off pairing your headphones for your iPhone (or any other device that they can already be coupled to) before their pairing at your watch.

  It can also help when you try to pair your headset with your watch, to move the two devices to another place, away from any device Bluetooth can be active.

• IOS error 10 Bluetooth headset

  Hello

  Since I've upgraded to iOS 10 on my iPhone 6, my quick mpow Bluetooth headset does not work as Hey used to. When I turn on, they automatically connect to the iPhone and I get the small icon beside the battery meter indicates the State of charge, however, they do not appear as an audio device in spotify, itunes or other audio applications.

  Only the way to solve it is to "forget the device" and re-pair the helmet - pain in the * when to go to the gym, etc.

  I tried to reset the network settings according to another post on the forum, but there is no reaolve the question.

  Any ideas? She must have iOS 10 as they worked perfectly well until last week and I tried it on my iPod touch 4th generation and they work perfectly.

  Thank you

  I have this problem also with a SoundPeats QY8. I think it's a bug of iOS 10 because he was allowed in the iOS 9.

  In order to obtain the device name displayed for audio playback, one solution is to click on the name of the device under Bluetooth settings after it is already connected, which is a useless chore.

• AirPlay only list bluetooth headset after the connection

  Hi all

  I wanted to see if it's just me or other people see this. I use iPhone 5 that I've recently updated to iOS10. In my daily use, I connect headphones bluetooth (4.0), MPOW Swift is the brand, to listen to music or watch YouTube videos. With iOS 9.x I never had a problem with the headphones recognized and used by all applications via AirPlay immediately. With iOS 10, which is not true. They connect as I see the icon in the status bar of the phone and Bluetooth settings section says that it is connected but when I go to music app and click on AirPlay they are not listed. I found to solve the problem, I must forget the device to the headphones and then repair and immediately their names still AirPlay and sound comes from the app through the headphones. This is the best though, if I turn the headset off power (disconnect device), then reconnect, I'm back to the same problem where they do not appear in the AirPlay and I pairing again.

  Anyone else see this problem? Unfortunately, I don't have another bluetooth headset to test this.

  Thank you!
  Jeff

  I'm having the same issue. It happens with all my Bluetooth devices. The Bluetooth is connected, as indicated by the icon in the status bar, and the said device. But music, iHeartRadio etc. play via speaker phone. Curiously, the phone works via Bluetooth and the active key Siri is not a problem of Bluetooth.

  I did some research and tried to reset my network settings as recommended without result. Now whenever I turn in a Bluetooth device, I have to connect manually if I want to use it for anything other than the functions of the phone. Very annoying.

  Apple, any suggestions?

• loss of control ipad (screen magnify in-app Youtube kids) when you use a bluetooth headset

  loss of orders for ipad from tap - specifically screen expand in the Youtube kids application when you use a bluetooth headset

  I would contact with the helmet manufacturer or the helper application developer. Maybe it's that the app may need to be updated.

  Barry

• Can't associate my Sennheiser Bluetooth headset with my Verstuurd vanaf mijn IPad Pro and IPhone 5 s

  Can't associate my Sennheiser headset to my Verstuurd vanaf mijn Ipad Pro and my IPhone 5s.

  They ore well on my IPhone 4S and the Ipad 2.

  whatncan deceive you?

  to associate a bluetooth headset device that it has not been paired with before putting the headset in discovery / pairing mode your sennheiser manual should describe how you are going to do

• Notification by email to the phone and not headset/Bluetooth Headset

  I have an iPhone6 and whenever my bluetooth headset is connected, my notifications by e-mail through the headset and not via the phone.  I need to call to keep giving me the notification and send it through the headset.  Often, I have my phone and the headset on my desk and will not hear the notification.  I'm pretty sure I could change this once, but can't remember how.

  Maybe you have active AirPlay? Swipe up from the bottom of the screen to display the command center and ensure AirPlay is disabled.

  How to use AirPlay on your iPhone, iPad or iPod touch - Apple Support

  Also, go to settings > general > accessibility > routing of Audio calls > and set it to automatic.

• Phone calls via bluetooth headset.

  Can I answer the phone calls on my Apple Watch and hear the caller through my bluetooth headset paired instead of through the loudspeaker of the watch?

  Hello

  No, it is not possible currently.

  If you want to suggest that Apple considers adding that as a new feature, you can do so here:

  https://www.Apple.com/feedback/watch.html

• iPhone Bluetooth Headset open iBooks?

  So I use my Plantronics Voyager Bluetooth headset for listening to audio books of every night.  My books are in the iBooks app is where I play.

  I'm now noticed something really annoying that I can't fix.

  Now, whenever I connect my Bluetooth headset, it opens the iBooks and starts to read an audio book.  It does this without any prompting from me.  The iBooks app is not really open in this case, it shows just at the bottom of the screen as a bar in the narrow application screen.  It shows also in the Control Center screen.

  There are no settings for my bluetooth headset.  I looked at the settings for the iBooks, and there is nothing about it.  I went through all other screens of settings that I can find and I can't find anything on how to stop this.

  It may not seem like much, but it's really annoying, and when I'm driving and I turn on my headset to answer a call, iBooks automatically begins to play on top of the current phone call.

  I searched and could not find anyone else with this problem, so I don't know if this is specific to my bluetooth earpiece/headset or what, but there must be a way to stop this.

  Any help would be greatly appreciated.

  Thank you

  In fact, I have this problem too, and everything has happened today on my iPhone. However, I do not have a Bluetooth headset; just Sony headphones with a 3.5 mm jack. Whenever I plug my headphones in, the suggested application that could be opened appears iBooks and not music. At first I though it will be fixed by just open music, playing a song and then to pause the selected song. Later, I'll disconnect the Atria, then quickly reconnect. Then, the app suggested turns to music (as I wanted). But the proposed application back to iBooks when headphones are not connected for a long time.

  iPhone 5, iOS 9.3.2,and Sony headphones with 3.5 mm jack