Bluetooth remains plugged in car while the radio does not work

Similar Questions

• SR400 while the loop does not work

  Hello

  I'm using LabVIEW for control SR400 through a GPIB card.

  I use SR400 to count the number of signal in a second, wait 0.05 s, then again count the signal once, wait 0.05 s once again, and so on.

  However, the while loop didn't iterate. When I started the program, it is only once.

  In execution of highlight mode, when an iteration is finished, he waited a long period starting the next. In normal mode, it doesn't have to iterate.

  Also when I clicked the stop button, it's been clicked. However when I wrote a very simple program, the stop button worked normally.

  In any case the button issue is not very important. I don't care that the program iterates forever or not. I just want to iterate.

  I searched the jury and had not could not any related problem.

  Is it better to attach my VI? The VI is in my computer lab.

  Thank you very much!

  This code just feels bad.

  (No real management mistakes, deep, stacked sequences FOR lines that are wired to iterate through only once, controls on the right and right to left, wiring weird code on average the last 10 items (Hint: means ptbypt with a length of 10 sample he would!).) If you want to use the wire of the error, the sequences would not even necessary)

  If the stop button does not reset, it means that the iteration of the loop does not terminate. It can fill in only if the two structures of the sequence ends.

  Have you tried running in execution, emphasizing fashion while looking at the diagram? Probably one of the communications is at a standstill. For example, the instrument sends really 6 bytes at the end? When you set the overall timeout and what is it?

• Photosmart C7280 will not communicate with the network. The diagnosis says that the Radio does not

  Photosmart C7280 C5582A work through a MacBook via a Mac (OS 10.5.7) wireless router was working fine last week.  Today when I tried to print, the printer was stuck in the "printing page 37%.  When I checked the Print Manager, the printer was "slowed" and since I had a lot of trouble with this printer connection before losing, I did what HP told me the last time which was to remove the printer and then recharge it.  Except that this time, once the printer has been deleted, he could not find the printer even after I restarted the wizard and reinstated the SSID and WPA many times.  I have reset the printer and the router by turning off and disconnect power provided, but he still had the same problem.  When I ran the diagnosis, he told me: 'Pass on Radio, Radio work on failure, not plugged cable Ethernet-Pass' the rest of diagnosis is "not run" and other data on diagnostic tests are the Mac addess.  The Diagnostic says the "wireless radio does not work.  Contact HP support.  Unfortunately, it's evening Sat and HP support is closed.  Any help or is this printer dead?  (I spent a fortune on ink cartridges)

  It is indeed a hardware problem then.  I'm sorry.

  I always believe that repair costs would be better put towards buying a new printer.

  However, there may be options that I'm not aware where do not have access to.  This document has some support listed options.

  However, I recommend you contact HP support at the 1-800-474-6836 (to the United States and Canada).  Phone support can provide that more than an estimate on the repair or replacement of the printer with HP and you could compare this with the cost of a new printer.

  A new printer is under warranty and most likely to be an improvement on an older printer.

• In the attached VI why looping force the type of data while the other does not?

  In the attached VI why looping force the type of data while the other does not?

  I'm guessing that you have created the Enum on the front panel.  If you right click and create an indicator, it corresponds to the type and be an enum.  LabVIEW represents enums as U16, but because the types are not the same (for example, your enum has 3 values, but a U16's 65 536 values), LabVIEW automatically converts value (or converts) the smallest representation (enum) in the largest value (U16).

• The wireless radio does not work

  The wireless radio does not work on my HP Photosmart C309a (Vista 32 - bit) - support contact HP on the wireless network Test report

  The number of UK should be 0844 369 0369

• "Wireless radio does not work" when the Diagnostic tool is run

  Recently, I unplugged my C309a HP Photosmart Premium and he moved to a new Tablet next to my main computer.  Wireless network card works perfectly before the move, and now it does not detect networks to connect to.  I have run the wireless network test report and it says "Wireless Radio does not work.  Contact HP support. "I can do here to help solve this problem, or I have to pay for repairs somewhere?  I want to believe that this HP product can support more than a simple passage of one shelf to another...

  Any suggestions would be greatly appreciated!

  * Note * I know my network works correctly (because I'm connected to it now...).  My computer detects my network as well as several others in the neighborhood.

  Is the printer still under warranty?  If yes you can not he repaired, but it can cost almost what a new printer costs.  Here is how to contact HP.

  Your printer must be able to work with USB and it should also be able to be connected to your router with an Ethernet cable.

• Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer

  My computer stops the update via WIndows Update Component

  Whenever a try to do the manual update using this component I get the message;   * Windows Update cannot currently check the update, because the service does not work, you may need to restart your computer *...

  My computer has a few updates, but can not run these update

  Whenever I try to run computer shotdown/updates remain frozen for a while and stops without updating

  He starts to run updates 1 of 13... and stops

  If I shutdown normal e, computer stay likehanging 1 hour without stopping.

  I would like to know how to solve this problem

  Thank you

  Concerning

  Gladmar.

  Hello

  Were there any changes made on the computer before the show?

  Perform the following methods and check:

  Method 1:

  I suggest you to check if you are able to access Windows Update service and ensure that the following services are started. If it is not started, follow these steps:

  a. click Start, type services.msc and press enter.
  b. search Windows Update.
  c. right-click on the service and select Properties.
  d. in type of startup, select enable.
  e. click Start under the Service status.
  f. click OK.
  g. Repeat steps c to f for the following services:

  Background Intelligent Transfer Service
  Cryptographic services

  If the steps do not help to solve the problem, you can go ahead with the methods mentioned below and check.

  Method 2:

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Method 3:

  Your anti-virus software is in conflict with Windows updates. You can test this by temporarily disabling your antivirus:

  Disable the antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 4:

  The problem with Microsoft Windows Update is not working

  http://support.Microsoft.com/mats/windows_update/

  See also:

  Troubleshoot problems with installing updates
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Updates: frequently asked questions

  
  http://Windows.Microsoft.com/en-us/Windows-Vista/updates-frequently-asked-questions

  I hope this helps.

• CD drive does not open and the light does not work

  original title: single CD player problem

  The problem with my CD player seems to be unique I can't find an answer, or someone else with the same problem online.

  My computer is custom built, the CD player lasted me 1.5 years no problem, not until one day I realize, it does not open and the light does not work on it, I ordered a new drive and installed that one, still does not work. so, I replaced the SATA cable which connects to the motherboard, still does not.

  When I go to my computer the drive appears but when I right click > eject it says: "year error occurred while ejecting CD drive D".  It also appears in devices such as SCSI CdRom Device Manager but I am not sure if it's actually my CD player.

  I also tried troubleshooting http://support.microsoft.com/gp/cd_dvd_drive_problems and no solution.

  WTFFF ideas? I really hope that its not the motherboard

  There are two cables you need to connect to the drive, one for data and one for power.  You must connect both training at work.  If you only have the data cable is plugged and not cable power which would be a possible cause of the problem that you see.

  "Ryanb1290" wrote in the new message: * e-mail address is removed from the privacy... *

  Sorry, im just of knowledge about computer hardware.  you say that I should try a different agreement or another port to plug in?

  I tried to connect on a couple different SATA ports on the motherboard.

• Help, says report wireless radio does not work contact HP suport *.

  Help, says report wireless radio does not work contact HP suport *.

  Wireless on collar

  work wireless FAIL

  Reset your C7280 by turning it off, press and hold # and 6 keys while and shortly after turned it on.

  Now, run a Test of the front panel wireless network.

• FN + F3 disable the Touchpad does not work. Dell XPS L702X

  Hello, I am new to this forum.

  The function FN + F3 that disable the Touchpad does not work, my laptop Dell XPS 17 (L702X)

  I googled my problem and the only thing I found was this: http://en.community.dell.com/support-forums/laptop/f/3518/t/19454265.aspx

  I think that my problems with the touchpad started when I plugged a mouse into the USB port. It didn't work (it worked well before), and in material-sound-mouse control panel, the system asked me to uninstall a driver or other. I do not remember, but later the mouse worked.

  After this weird thing with the mouse, I noticed that the touchpad was malfunctioning. While I write, the cursor moves without touching the touchpad, it is annoying because it makes me write bad because he is moving in the middle of writing, as I write so it's a mess.

  The second oddity, the Fn + F3 does not disable the touchpad, the orange light come on (the led on the top of the touchpad), but the cursor can be moved in any case, with or without a connected mouse.

  I checked for driver updates, perform an audit of the system, checked for viruses, spywares and I don't know what I could do. I don't know if the problem with the mouse had nothing to do with the function Fn + F3 problem.

  I have not formatted or re installed windows 7, never.

  In Device Manager I have this:

  -mouse and other pointing devices:-Compatible PS/2 mouse

  Help, please. Thank you.

  DOH! Problem between Chair and keyboard...

  C:\dell\drivers\R289237

  Run the executable file of Synaptics.

  Download of extracts only the program on your disk. You must manually install the driver for the Synaptics touchpad with its own executable.

  FN + F3 now disables =)

• using firefox 24, yahoo toolbar disappears and the keyboard does not work on some websites

  We have installed firefox 24, yahoo toolbar sometimes disappears. On some web site when trying to enter a password, the keyboard does not work until you double click of the mouse on the registration form. This on two different systems of windows 7. Each thin seemed to work fine before the update prior to the installation of 24.

  Hello

  Try Firefox Safe mode to see if the problem goes away. Safe mode is a troubleshooting mode, which disables most of the modules.

  (If you use it, switch to the default theme).

  • Under Windows, you can open Firefox 4.0 + in Safe Mode holding the key SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac, you can open Firefox 4.0 + in Safe Mode holding the key option key when starting Firefox.
  • Under Linux, you can open Firefox 4.0 + with leaving Firefox then go to your Terminal and running Safe Mode: firefox-safe-mode (you may need to specify the installation path of Firefox for example/usr/lib/firefox)
  • Or open the Help menu and click on the restart with the disabled... modules menu item while Firefox is running.

  

  Once you get the pop-up, simply select "" boot mode safe. "

  

  If the issue is not present in Firefox Safe Mode, your problem is probably caused by an extension, and you need to understand that one. To do this, please follow article Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems .

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. It might help others who have the same problem.

  I hope this helps!

  Curtis

• Key on the keyboard does not work in firefox box when you type in the web site, but it works everywhere else?

  Key on the keyboard does not work in firefox box when you type in the web site, but it works everywhere else?

  Try Firefox SafeMode to see how it works there.
  
  A way of solving problems, which disables most of the modules.
  
  (If you use it, switch to the default theme).

  • You can open the mode without failure of Firefox 4.0 + by pressing the SHIFT key when you use the desktop Firefox or shortcut in the start menu.
  • Or use the Help menu option, click restart with the disabled... modules while Firefox is running.

  Do not choose anything at the moment, just use 'continue in safe mode.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before using the shortcut of Firefox (without the Shift key) to open it again.

  If it's good in Firefox Safe mode, your problem is probably caused by an extension, and you need to understand that one.
  
  http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+themes

  Can be caused by an add-on to the AVG.

  When find you what is causing that, please let us know. It might help others who have this problem.

• The mouse does not work on my new Satellite L750/L755

  Hello world

  I bought a toshiba Satellite L750/L755 but the mouse does not work, I have no control on it that if I use an external mouse, while I have put pressure on the touchpad.
  I tried the following options:
  I updated the driver - I changed the operating system

  but nothing, still the same problem. Next laptop will be a Mac for sure.

  I look forward to hear from you

  Daniele

  Hello Daniele

  It's really strange that the touchpad does not work even if you have installed the right driver and installed the operating system again. At the first moment, we can say there is probably a hardware problem, but please be sure touchpad is listed in the Device Manager and also active correctly (FN keys).

  Check it please all the properties of the mouse.

• Satellite W30T-A378 from - touch pad and the keyboard does not work

  I have a problem with my laptop, the touch pad and the keyboard does not work.
  Can someone help me what is the possible cause?

  Thanks in advance.

  Hello

  I guess you checked if the Tablet has been properly connected to the docking keyboard.

  Have you tried to unplug and plug the docking again?
  Note: there is a latch on the left you have to move and in order to remove the tablet.

  Perhaps there is a connection problem.

• MacBook pro a key on the keyboard does not work

  Hello

  Last day I was cleaning my keyboard (I do not used any water or liquid), and when I handed the keys, I found that my 'enter' key does not work.

  I think it's because that material because the key does not work even without the key cover. Is it possible that I have demaged some buses on the baseboard of the keyboard?

  In addition, I can not open Apple Diagnostics, and while I turn on my macbook it produces sounds like that I am button constantly some.

  -Make an appointment at the Genius Bar to an Apple store to discuss your options.

  Shop Apple Store - Genius Bar

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.