blur the bios screen

Similar Questions

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Need to access the BIOS screens

  "HP Pavilion p7-1447 c desktop PC Win8x64.  FN2 gives me the diagnosis UEFI screens.  I need to enter the BIOS to set the NumLock on at all times.  How to access the BIOS screen?

  Hello

  Turn on and immediately press the ESC key to access the select start--> F10 menu to access the BIOS.

  Best regards

  ERICO

• When I restart Windows 7 home premium, the computer hangs on the bios screen.

  I don't know what exactly when this problem started, but I can stop the machine and it will start normally.  If upodates are installed and the machine restart it hangs at the bios screen all the time.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• keyboard does not work when you start. Unable to get to the bios screen.

  When I reboot to get to the bios screen my keyboard does become functional until windows load. I don't remember what is a problem in the past, but since I disconnected everything recently I was wondering if it happens to be a USB port which remains hot during startup.  I have a Gigabyte motherboard.

  Thanks for all the help.  I found a port that remained hot during startup.  Not an easy feat because there are 6 USB ports on my MB.  Then after may restart to finally find, I remembered that I have also 2 USB ports on my Dell monitor that remain hot even when the computer is off.  A lesson I will never forget.

• NB200 does not start after the bios - screen black screen with blinking cursor

  Hello

  I was using the laptop as usual when I think there may have been a virus activity - reason I say that is that my anti-virus closed unexpectedly. I couldn't restart programs files.

  I restarted the laptop.

  After the bios menu will I get a blank screen with a blinking cursor - windows does not start.

  I did the following:
  (1) create a USB bootable with Recovery Console window XP - boot with this i can see three drives C:, D: as SDA? I can see the content of these disks, so it seems that my HD works. I ran a fixmbr and fixboot, but this has not solved the problem.
  (2) create a Kaspersky bootable USB virus scan - ran it without problem - he found a few question (not on the disk boot sector) I've fixed.

  An option was to copy files from the laptop and then start it in recovery mode - so Itried to run the phone into recovery mode hold down the 0 key at startup - the bottom of the screen then displays * HDD Recovery mode * and nothing happens.

  Any help - other options would be greatly appreciated.

  My 1 year of that guarantee has expired a few months back so can't send in for repair.

  Thank you

  Hello

  I doubt that it is a virus.
  Seems the file system is damaged on the HARD drive and this is the reason why the laptop does not start until it could also be a partition of HARD disk malfunction.

  Try this; Turn on the unit, press F8, and then check if you have the laptop repair.
  If this is not possible, then you will need to reinstall new OS.

  Here you can order a recovery disc:
  http://backupmedia.Toshiba.EU/landing.aspx
  Of course you will need an external USB CD/DVD drive

• Equium A300D - after updating the BIOS screen is empty

  Hi, I did a bios update on my Equium A300D-PSAK2E and its bricks of my laptop! When it restarts after update screen is empty!

  Is there a a sort of way to launch a recovery of bios by pressing certain keys on the power on the image of the bios on a USB?

  Kind regards

  Dan

  Hi Dan,.

  Unfortunately I think that there is nothing you can do if the BIOS update gone wrong... In this case the ROM module must be reflashed to an authorized service because guys have special tools to do this process delicate reflash.

  You can find a list of aspic here:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

• Satellite M40 does not load before the BIOS screen

  When I turn on my Satellite M40 unfortunately it does not happened on 7/8ths blue bar going across the screen.

  That left me completely baffled as what to do.

  Apparently, it could be repaired by removing the cables on my CMOS battery?

  If someone knows how I would go all this? or have any other ideas?

  Thank you xx

  Hi Dec,

  Blue scroll bars indicate that the Wondiows operating system is loaded from the hard drive. If this process hangs while loading, then it is likely that the hard drive itself is defetive or else the files that are being loaded are corrupt and cannot be loaded.

  Interfere with the CMOS chip will not fix this problem because the BIOS has already been loaded at this point.

  If you have access to a bootable CD/DVD (such as Norton Disk Doctor) then I siggest you boot from it and running a scan of your hard drive. Alternatively you can try reinstalling your operating system of the Toshiba recovery CD but it won't replace your own data on your hard drive.

  concerning

• P7-1243: P7-1243 and Asus GeForce 210 blocking card video in the bios screen

  I have a p7-1243, which works fine on the integrated graphics, but when I installed an Asus 1 GB silent graphics card GeForce 210 it locks upwards at the start of wood screen where it says "Press esc...". "The PC is completely stock configuration. I got a 4 GB of additional ram, but it is deleted.

  I was surprised to find no updates for the chipset of your motherboard or bios. Any suggestions?

  @xxxxxx_x

  The BIOS updates are displayed under Windows 8 here.  It's your decision.

  BTW - The NVIDIA 210 known compatibility issues in some HP computers.  You might want to try another graphics card.

• Yoga 2 Pro stuck on the BIOS screen

  Yesterday using my pro, I let the battery run completely. When I went to use the computer today, the computer is stuck on the white screen of lenovo.

  Computer will not configuration options or boot bios enter unless the hard drive is removed. I can run the computer without the pcei HDD when you use a disk external hard usb. Not really sure where to go fron here. I tried to remove the hard disk, booting from a flash drive, then reinstall the pcei reader, but it does appear quite Similarly when searching for it through the command prompt. Thinking I have a bad drive hard, but I am at a loss at the moment

  Yes, I'm guessing that the drive might be bad.

  Try the Secure Boot turn off/on or affecting in the UEFI/Legacy BIOS as well. It might allow you to start an external drive.

  Make sure that the boot order is set to an external start too.

• Pavilion 15-ab137ca: stuck on the management of the BIOS screen after BIOS update

  A ran a BIOS update that was a solution on this forum to prevent the Startup Menu to appear whenever I start the machine. Said that he would change from F16 to F10. Now, he has been slain on the screen of the BIOS for 30 minutes management. The display shows, the system BIOS is updated. This update will take a few minutes to complete. Do not close or remove the external power supply to your computer during the process. Check the new BIOS image. Block 2048/2048. Progress at 100%. How long should I wait?

  Hey!

  I am pleased that you are in your laptop.

  What is the screen below as you talk?

  

  All HP and Compaq computers that were manufactured with 10 Windows can use Secure Boot. Secure startup is enabled by default on these computers.

  If the image above is actually what you are talking about, please take a look at the documentation for Secure Boot . You will see a section called disabling Secure Boot... This should help you with the start menu.

  I hope this helps!

  Please let me know!

  Have a great day!

• Computer Vista gets to the BIOS screen, then restarts continually.

  It's on a Dell Inspiron desktop PC. I was browsing youtube, when I noticed when I clicked on something, he did not. Although the outlines of the buttons flashed as soon as I waved above them. If I clicked on a bookmark, it says that my internet connection is bad. But I was watching youtube, 3 minutes earlier.
  I close firefox, then go to the office. I CAN'T RIGHT CLICK! OR LEFT CLICK. On some points, I can click.  And some I can't. I unplug the computer from the wall. Rinse power. Wait 5 minutes. Restarts. Computer gets to the Dell BIOS screen. Will beep once, makes a sound of flickering, light flashes orange and repeats the process forever. I press F12 for the boot menu. Press enter on the SATA hard drive. And it starts fine. But I want to solve this problem, help!

  Hello

  You do not have the cold hard first permanently in the boot order?

  If you do, try the following steps to find your problem:

  "The computer does not start in Microsoft Windows Vista"

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=DSN_343119&isLegacy=true

  Using Dell Diagnostics:

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=52057

  See you soon.

• Vista 64 does not start after the bios screen. Can not boot from the recovery cd or help

  Last night a MS pushed a windows update and my pc restarted automatically.  But it does not actually restart.

  The PC goes through the bios tests, passes and then crashes and does not start in Vista.

  I can't start at all, including safe mode.

  I can't the system recovery option in HP bios to load.  Can I only use my Vista64 system recovery bootable cd or actually start.

  First of all, I thought it was a HARD drive problem, but tests of the bios disk hard that all spend, even the 2 hours 'SMART' test that he was running.

  Help

  Hello

  What happens when you try to boot from the recovery CD? You receive messages or error codes?

  You can check if the boot in the BIOS settings priority is configured to boot to CD\DVD.

  NOTE: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  For more information, you can consult the following article:

  BIOS: Frequently asked questions

  If you still experience the problem, you may need to contact HP for assistance.

  HP support

  Hope this information is useful.

• NB100 - freezes on the BIOS screen

  This laptop has got sick. It opens to a bios, select screen with F2 to Setup and F10 for Boot Manager, either selecting simply said he is selected and then wait. Can not go further.

  I wand to remove the hard drive so I can retrieve the data but cannot penetrate inside the case. Anyone know how to remove the hard drive? It's a Toshiba NB100 (no optical drive).

  Any help with be appreciated.

  > wand to remove the hard drive so I can retrieve the data but cannot penetrate inside the case.

  you don't need to remove the hard disk to retrieve the data, you can create a USB windows live for a start, then, and backup important data all

  http://www.ANewMorning.com/2009/01/15/create-a-live-Windows-USB-stick/

• Help! can't see the bios screen! DV7 - had to solve myself - idiots here

  
  

  Finally figured out how to enable VT - X in my bios without my computer screen or the * beep * ing * beep * ers here that can't help with * beep * cus they're idiots. ESC-> F10, right, right, right, right, down, enter, up, enter, F10, up, enter, enter - only took 4 months

  [scott@localhost ~] $ lsmod | grep kvm
  kvm_intel 138528 0
  KVM 422809 1 kvm_intel

  Thanks for nothing, evil be ever buy any material hp ever again and will recommend that the company I work helps to ensure that they do not buy anything for HP data center.