Boot camp: drive could not be partitioned

Similar Questions

• How to fix the fsck "your drive could not be partitioned..." Bootcamp does not

  Hello, after days of searching for a solution and try several times to fix this, I write a question.

  I want to create a partition with Bootcamp to install Windows 7. Here's what I made in the following order:

  1. Tried to partition with bootcamp, but he was only let me pick 32 GB or 1024 GB (which I did not available).
  2. Manually create the partition with utility disk and at the start of my flash, found that USB 3.0 drive / Bluetooth drivers don't would not load then ran in question where I couldn't go beyond 'select language' screen on Win 7 install.
  3. Tried to restart and delete my partition but noticed that I couldn't so I had to boot in recovery of the Internet and the use of the terminal commands and gpt, deleted the unused partition and used disk utility to merge it into main drive. I followed these instructions: deleted my bootcamp partition, but can not resize my osx partition
  4. Re-directed training camp and received the error "your drive could not be partitioned."
  5. Disc repair/check etc. ran and found errors.
  6. Run fsck by this thread that your disk cannot be partitioned. Win7 Bootcamp and still got here.
  7. Thought that maybe filevault caused outcome so disabled that. 48 hours later my 2.3 TB have been deciphered.
  8. Ran bootcamp, same problem.
  9. Run fsck, same problem.
  10. Currently using TestDisk to analyse the sectors on disk 1, correct? :

  

  

  I'm ready to create another partition manual if I can get drivers USB/BT to work.

  
  

  Furthermore, anyone know why there is a limit of 32 GB/1024 on the size of my partition for bootcamp? Why can't choose anything between the two?

  Data sheet:

  

  Thanks in advance for any answer!

  Please after the release of

  Cs diskutil list

• I am trying to install windows on my Mac Book Air 2014 10 and I get the message "your drive could not be partitioned.

  When using Boot Camp, I proceed to the stage where he made the partition. I'm out 19 concerts for OS X and the allocation of 50 GB for Windows. I deleted all other external drives then the flash drive that has the Windows ISO and I keep getting an error. I already did a disk repair and remove all external hard drives as well as drop-down list and good road. Help please!

  

  Can you OSX boot without failure - try safe mode if your Mac does not commissioning - Apple support - and start normally and try again?

  Please after the release of OSX Terminal commands.

  diskutil list

  Cs diskutil list

• Windows 10 iMac 27 "el capitian Boot camp Installer could not move forward and the black screen appeared

  I have an iMac 27 "end 2015, el Capitian, boot camp 6.0. 10 64-bit pro Windows, everything goes fine until the last step when the Boot Camp Installer appeared, when I click Next, the screen is black... tried new facility twice, still stuck in the last step with the Boot Camp Installer then click Next, the screen become black... Please help!

  Some at Microsoft should lose their job (s) on that moment this crass brain freeze. Please remove the current installation of Windows, re-run BCA and create a new partition and you disconnect from the Internet before Windows Setup ask you where you want to install Windows.

  Please see installation problem w / 10 Windows on end 2015 27 "iMac retina as a reference.

• Solitaire: error "your drive could not be partitioned. Help, please

  Hey, solitaire

  After recovering disk space, I tried to run BCA. I used a 64 bit Win10 .iso downloaded from Microsoft. BCA created the installation disk, downloaded media files and allowed me to choose my size of the partition (same split) on my merger of 3 TB drive. Then I got the error.

  I have reset the SMC

  Rest PRAM

  None of the external devices are connected.

  I repaired the drive in disk utility, and restarted in single-user mode and made a repair of the AF - / sbin/fsck.

  Also, I started in safe mode to try BCA from there, but he couldn't find the Win installation disc, even if disk utility could find it.

  Here is my list of current diskutil:

  

  Cs diskutil list

  

  This is my current research on the problem brought me. I remember seeing a bunch of odd discs added to diskutil when it is run in repair mode. There were about ten of them. I don't know if they were repaired during the previous process.

  Ideas? Thank you!

  As you test, use utility disk to create a FAT of 1 partition to or more and check the result of diskutil disk1 and sudo fdisk/dev/disk1 list and check if it works. If so, you can always delete the partition and use wizard BC.

• Boot Camp Assistant does not start the installer

  Hi all -

  I'm trying to install Windows 8.1 or 10 Pro on my mid 2015 Macbook Pro. I made this countless times on before Mac computers, including my 2013 previous Macbook Pro without problem. However this laptop seems to have problems during the process. Or I do something wrong and don't understand how it works now.

  I started Boot Camp Assistant, walking through the steps, divide the disk, etc. He began the restart process, then it restarted,... then I was back to my Mac. There was no indication that he was still something, but I let it sit for a few minutes. When I was confident it would do nothing, I decided to restart and hold down the 'Option' key on startup to select the Windows disk...

  OK just thought of this, but I will continue to write this question: Boot Camp Assistant request now an ISO standard. I still remember having to do this from a USB or CD player. I hold down the 'Option' and select the DRIVE or a CD drive but since I do not have either, I can't select it. I thought it was a problem in which nothing appeared on the screen except Macintosh HD.

  So I guess that the problem comes from my ISO file? I made them using the instructions from Apple of physical disks (Windows 7 and 8.1, but my laptop does not support 7). I will try to download Windows 10 Microsoft site, according to Apple.

  Anyway, I looked in the disk utility and found that BOOTCAMP was created successfully. I used Boot Camp Assistant to delete the partition and to combine the disc again. I then tried the whole process, once again, but with the same results.

  Still, I will try with a new ISO directly from Microsoft...

  Thanks for any input in advance.

  -Tony

  1. 2015 macs do not use a cable USB or CD/DVD to install Windows.

  2 creates a partition on the internal drive called OSXRESERVED and puts the content of the ISO and the drivers of BC on this 8 GB partition and boot from it.

  3. Please see https://help.apple.com/bootcamp/assistant/6.0/ for more details.

• I am running XP and now I can't re - install after installing Windows8, I I get messsage that floppy drive could not be found, but I don't have a floppy drive.

  I want my XP back

  I am running XP and now I can't re - install after installing Windows8, I get I messsage that floppy drive could not be found, but I don't have a floppy and player despite the choice of boot from my cd rom and by disabling the floppy drive the same message at startup When I scan for my cd rom he sees them, but say that they do not function correctly, any ideas what is happening? They were fine before, my BIOS did not change to recognize my cd rom?

  Reinstall Windows XP
  http://michaelstevenstech.com/cleanxpinstall.html

  Insert your Windows XP CD, and then restart your computer.

  When you are prompted to boot from the CD, do so. To do this, press any key on the keyboard.

  Windows XP will go into its configuration process.

  Once you arrive at the welcome configuration, press enter on your keyboard to start the installation process

  Press F8 on your keyboard to accept the license agreement

  Select the partition, and then press D on your keyboard to remove it

  Select Format the partition using the NTFS file system

  Press F on your keyboard to start the formatting.

  Installation files will now be copied to your hard drive

  Your system will be rebooted, the installation of Windows XP will continue

• Windows Small Business Server 2011 - "windows setup cannot continue because a required driver could not be installed.

  Hello

  I try to install windows server enterprise on my hp proliant gen 8. I used smart supply and that everything was working fine, when switching to the windows installation it gets to 99% then comes up with the error:

  Windows Setup cannot continue because a required driver could not be installed

  I was wondering what I can do to solve this problem, I have tried several times without success. Thank you for your time.

  Hello

  Your Question is beyond the scope of this community.

  I suggest that repost you your question in the Forums of SBS.

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver

  "Windows Small Business Server 2011 Essentials online help"

  https://msdn.Microsoft.com/en-us/library/home-client.aspx

  See you soon.

• "Windows Setup cannot continue because a required driver could not be installed" while improving to 64-bit

  I'm trying to install windows 7 64 on a 32-bit with the custom installation option. All is well until that right at the end of the installation it gives me this error "Windows Setup cannot continue because a required driver could not be installed. I tried this several times but the same results. I used the windows Upgrade Advisor to see if my computer is compatible and it is no problem.

  Error image: http://imgur.com/lOVj6eX

  Restore the previous installation of Windows and do the following:
  1 disable any security software before you attempt to upgrade or do a clean install.
  2. make sure that your computer is updated (devices and applications)
  3. disconnect all external devices before installing.
  4. check your hard disk for errors:
  Click Start
  Type: CMD, according to the results, right-click CMD
  Click on "Run as Administrator"
  At the command prompt, type: chkdsk /r
  When you restart your system, your computer will be scanned for errors and will try to correct them.

  In addition, run the Windows 7 Upgrade Advisor, it will scan your system and provide a report telling you if your PC can run Windows 7, and if there is no compatibility problems with your hardware or programs.

• «The video add-on drive could not install: impossible to validate the license online.» How can it help me? I tried the Extension handles CC too. But no success.

  «The video add-on drive could not install: impossible to validate the license online.» How can it help me? I tried the Extension handles CC too. But no success.

  This error indicates usually that one of the following problems:

  • You are not connected to Creative CC Cloud Desktop App and/or Adobe site with the same Adobe ID modules.
  • More than one user is logged in your Adobe software on your computer using an Adobe ID different from yourself, or indeed you have more than one Adobe ID that you used to connect to and the license file is damaged.
  • You are behind a firewall that blocks our license server calls.

  Please first make sure that you are connected to the Adobe website modules (top-right) and the desktop application CC (high button on the page of good settings, preferences, account) with the correct ID. If you are, then next steps are please uninstall and reinstall the extensions, reset between Manager.

• "The CD/DVD drive could not be connected."

  Hi all

  I have a follow-up question to my previous question.  I have a CD with windows 2003 standard which I want to install on my virtual machine.  I go to 'Connect' CD/DVD 1 I connect to my $ E, which is my DVD drive.  But when I click on it I get the error:

  "The CD/DVD drive could not be connected."

  What I am doing wrong?

  Best regards

  Nathan-

  Please send me the screenshot of network configuration

  ability to chat in gtalk?

  concerning

  Prakash

• WiFi disabled in Windows Boot Camp 10, can not reinstall the driver

  Running an end of 2013 the MBP 15 "retina

  I got 10 Windows Boot Camp installed for more than a year without difficulty. But suddenly, my wifi doesn't work in Windows 10. He could see networks and said it was connected, but it has never been an internet connection.

  Assuming that it was the result of an update, I

  1 uninstalled all Windows regular updates that I can

  2. uninstalled the Broadcom driver

  3 downloaded the last Boot Camp Assistant WSS and installed

  But now I can't reinstall a driver for the Broadcom card! I tried to install WSS, but the network card remains in my device without a driver manager. So I tried to install the individual installation files in the folder of Broadcom. Still did not work. I even tried to extract all files Broadcom installation and manual installation of all the drivers. Windows 10 seems to recognize that the "ac" driver is the right, but always tells me that the driver installation failed without giving details.

  What else can I try?

  At your facility in W10 a W7/W8.1 update?

• Boot failure: REM could not detect 2 hard drives

  Hello. I bought a HP Pavilion G6 series laptop (LX273EA #ABU) last year and he stopped to load correctly. When I click on "Repair (recommended)" I get an error messaqe saying "REM could not detect 2 hard drives. I tried to start in safe mode and it will not work.

  The laptop is two months out of warranty, and the only support option I found is a phone call from £30 with no guarantee of assistance. Any input would be appreciated.

  Thank you

  Michael McDonald

  You are welcome Michaelmcd85.

  The 305 error indicates that the hard drive has failed. You will need to replace the hard drive.

  This is an easy repair so I'll give you the information you need to fix yourself. It's your interview Guide &. It contains information on how to disassemble the laptop. The guide also contains information that will allow you to choose a replacement hard drive.

  If you do not want to repair the laptop you can contact HP Support directly to the 1-800-4474-6836 if you are in the USA / Canada. If you are in another country, you must first visit HP's Support around the world to find the coordinates for your region.

  I hope this information is useful.

• Boot Camp, your disk cannot be partitioned

  Hello

  Can anyone help with this please?

  I tried it works and stop for months, and I do not get the case.  I tried almost everything I could find through google.

  Marc iMac: ~ list of ADR$ diskutil

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage Macintosh HD 3.0 TB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD + 3.0 TB disk1

  Logical volume on disk0s2

  2353FDE8-EAA1-4D1C-897D-4DAAC5D4CA2F

  Unencrypted

  / dev/disk2 (external, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: FDisk_partition_scheme * 8.0 GB disk2

  1: DOS_FAT_32 WININSTALL 8.0 GB disk2s1

  / dev/disk4 (disk image):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme + 3.0 TB disk4

  1: EFI EFI 209.7 MB disk4s1

  2: disk4s2 Apple_HFS TB 3.0 backups Time Machine

  Marc iMac: ~ Marc$

  Marc iMac: ~ list of Marc cs $ diskutil

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group 4852D10E-9856-4C11-8C94-83CC0918FE2E

  =========================================================

  Name: Macintosh HD

  Status: online

  Dimensions: 2999733223424 B (3.0 to)

  Free space: 561152 B (561,2 KB)

  |

  +-Physical volume ED76BD88-7D21-4F72-8380-7E20A1118DC0

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 2999733223424 B (3.0 to)

  |

  +--> Logical volume family 0A09D639-5641-4B9C-99C5-5F60153D1484

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 2353FDE8-EAA1-4D1C-897D-4DAAC5D4CA2F

  ---------------------------------------------------

  Disc: disk1

  Status: online

  Size (Total): 2999380336640 B (3.0 to)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  I tried first aid in os x 10.11, no problem, safe mode, no problem.  Diskutil cs return disk1 and had the error 69741 target disk is not eligible for the review...

  Also tried single-user mode and/sbin/fsck - fy and that did not work.  I want OS X would give at least a clue, but I am at a total loss.

  Encryption is on, I turned it off and it always has. t work.

  Thanks in advance.

  Marc

  3 TB drives require a special partitioning on Macs that do not support Windows using boot EFI. What year/model is your Mac? El Capitan BCA is broken when handling this, but Yosemite and the Mavericks manage much better.

  It requires the partition Windows to be "sandwiched" between the two partitions on OS X, forming a volume of CS, so that a valid MBR can be created.

  Have you tried to create a Windows partition that was larger than 1 TB to test if it worked or not?

• Windows 10 anniversary + Boot Camp = Assembly is more Mac partition

  I have a MacBook Pro retina (end 2013) with Mac OS El Capitan, dual-boot with Windows with Boot Camp installed 10. Everything worked fine until I installed upgrading Windows 10 anniversary today. now Windows Monte is no longer the Mac partition. I reinstalled with success the latest Boot Camp drivers, but Windows still show me the Mac partition. (Starting in Mac OS works fine).

  Everyone knows about this problem? Anyone know of a solution or workaround?

  I wanted to offshore to see the cheers or boos... started Googling tonight and find that this Apple community and a Slashdot post in particular is disconcerting:

  https://Linux.Slashdot.org/story/16/08/03/1614223/Windows-10-anniversary-update-borks-dual-boot-partitions

  The report mentioned in the SlashDot is here:

  http://windowsreport.com/partition-disappears-Windows-10-anniversary-update/

  ... and he mentions a MiniTool Partition Wizard app. I'm looking on the site; the open air. I would try to download Windows and without committing to changes, driver changes, etc. he 'sees' the HFS partition +?