Boot from usb pendrive on Qosmio G20

Similar Questions

• NB100 - cannot boot from USB pendrive

  Hello

  I wanted to try out Ubuntu netbook remix, so I downloaded and it loaded in my key USB of SB after making the md5sum test. Then I fixed on the boot order so the usb port would start first and rebooted my Toshiba NB100 with the pen drive inserted. When I start my netbook the first screen where you can press F12 and F2 for BIOS freeze for about 2 min then start windows.

  I use a Kingston DataTraveler 4 GB USB key, I don't think it's the USB because as its bootable on my other laptop.

  Thank you.

  Hello!

  This only happens with the USB or without USB too?

  Have you tried another USB key? At the moment for me it sounds like the USB key is not compatible with laptops or isn't working properly.
  Can you please try another USB key?

  Good bye

• Booting from USB or USB-Flash on Qosmio G30?

  I would like to boot from a USB key with a PE Builder built the Image on my USB key. Is this possible? I can't find an option to boot from USB Stick. Drive HARD to the CD, LAN, only.

  I prefer this option to browse without risk of viruses, worms, adware...

  Please help me.

  Unfortunately, don t BIOS supports booting from the USB key or USB.
  You can boot from USB FDD, 1st/2nd HDD, ODD, or Network (LAN)

• Boot from USB

  Hello.

  I have a Pavilion p6720f desktop computer.  I want to boot from USB.  I just updated the BIOS that had supposedly fixed issues with the USB to boot. But there is no option in the cmos configuration in the for USB BOOT sequence.  The options are HD, CD, DISK, and NETWORK.  Any suggestions?

  OK PROBLEM SOLVED

  Plug the USB pen into a USB port of your PC (even the work of the port on the front)

  Reset

  Press < ESC > during startup to win the "Boot Menu" (or F12 etc. According to your PC)

  The USB pen is now listed (SanDisk in my case)

  Select it

  Press enter

  Linux starts fine

  Tell your wife or girlfriend, that she is no longer dumped

  Enjoy!

• Toshiba NB520 - can't boot from USB

  I NB520, I tried possible ways to boot from usb and it still does not work.
  I need some suggestions.
  Thank you.

  Usually the name of the USB device does not appear in the start menu.
  If you want to run rom flash USB memory key, you need to connect the USB flash first.
  Press the power button, then F12 and select USB.

  But note: USB flash memory stick must be ready for start-up.
  If it was not made "bootable" and then the boot from USB does not work.

• ProDesk G2 SFF 600 HP: HP ProDesk 600 G2 LTS cannot boot from USB or DVD

  We have 50 HP ProDesk 600 G2 SFF pcs and we need to install Windows 7.i can't boot from usb or DV.

  Please can someone advice me what to do?

  Thank you.

  Hello:

  We must go into the BIOS, turn on legacy mode and disable secure boot to install W7.

  Then you must also run this tool to set the USB3 drivers in your W7 usb flash drive.

  https://Downloadcenter.Intel.com/download/25476/Windows-7-USB-3-0-creator-utility

• EliteBook 1040 2: Boot From USB

  I looked at some other posts about it, but they were not helpful and tried a hat with the support of HP, but it was pretty useless. Without knowing it, I created a problem on my new laptop using EaseUS Partition Master to create a new partition which converted the drive in Dynamic.I only mention this as it may be relevant to the current problem.

  Now I can not create a recovery USB and can't the disk image. I made a backup of Windows with the backup system. Currently I am trying to boot from a USB key that contains the Hirens Boot environment. I tried this UB in my Dell and who will start in the environment of Hiren. Anyway, I went into the BIOS, inheritance and set the boot order to boot from USB first, but the computer will not.

  Hello

  http://www.partition-tool.com/EASEUS-partition-manager/convert-dynamic-disk-to-basic-disk.htm

  This can help with the first part.

• Re: Satellite NB10T-A-101 - cannot boot from USB key

  Hello

  I bought a new Toshiba Satellite NB10T-A-101 and want to improve performance by changing the HDD with a SSD and install windows Pro 8.1.

  However, I am unable to boot from USB, it always mention:
  + Reboot and select proper boot device or insert boot media in selected boot device and press a key. +

  I already disabled secure, used 5 + usb startup different sticks (work fine on other laptops).

  Can you please tell me what the approach is to change the HARD drive and then boot from a USB bootable (UEFI).

  Thank you.

  Hello

  Laptop Satellite NB10T-A-101 was equipped with an Intel CPU 2810 n which is part of the new Intel Bay Trail-M platform.

  This new technology Intel Bay Trail allows installation of UEFI capable systems:
  Win 8 or 8.1 Win

  Just a few questions:
  Have you already changed the HARD drive to SSD drive?
  If so, the new SSD is recognized in the BIOS?
  Have you tried to boot from the USB flash memory stick 8.1 Win until you changed your SSD drive?

• How can I boot from USB - Portege A200

  Hello

  I have a Portege A200 which is only a couple of years, but the hard drive no longer works. Initially, I thought that this was due to corrupt the boot disk record, but after trying to replace the drive hard (with two different readers), is showing a #0 IDE error when starting. So I came to the conclusion that the IDE controller chip is dead.

  In order to get labour latop, I burned a cd with the ubunto ISO. It starts off ok but due have only 512 MB of RAM, the system is somewhat limited and nothing installed is lost each time that I reboot.

  Now, I bought a 2 GB flash drive and installed ubuntu on it. My other problem is that there seems to be no boot from USB HDD or USB option in the bios.

  The options I can think of are:
  (1) Upgade the bios so that it supports the start of memory stick (although no HARD drive so do not know how I could reflash the BIOS or if there is even an upgrade of the BIOS that would support this feature)
  (2) create a cd that starts the boot process then tells the system to continue the initialization of the USB key (this is possible and does anyone know where I might be able to get these software)
  (3) boot from CD but the use of USB to keep any recorded information / everything installs etc (I suppose that similar to option 2 except the cd would manage the entire OS and USB would just "extra" information)

  If there are other options if someone may think I am happy to give them a go. Seems a shame to have to chuck to a laptop that is not particularly old, because the IDE controller chip has failed on the mobo.

  I have apppriciate any help anyone can offer.
  Thank you very much
  Mark

  Hello

  First I have to say that it of not possible to boot from the external USB device as USB, CD/DVD USB drive or USB HDD.
  It of only possible to boot from the external USB FDD (floppy) disk

  However, no opportunities for startup are clear, but I think that you misunderstood the IDE #0 error message. According to m that the IDE controller is not defective but only the new drive HARD is not compatible and not recognized by the BIOS.

  There are different reasons for this problem
  For the most part this error message appears if the HARD drive master/slave/c-salt settings are not correct.
  Generally these settings don t need to be changed or switched on the 2.5 hard disks but some hard drives support a rider that needs to be fixed in the correct position. But I put t if your HARD drive supports this

  In addition, the size of HARD drive isn't is not compatible could be the reason for these error messages!
  I would recommend so finally communicating with ASP in your country to get a new, compatible HARD drive and see if the same error still occurs.

  Good luck

• Desktop HP ENVY 700: problems with the boot from usb in the bios

  Hi I'm trying to boot from usb on a desktop HP ENVY 700. I don't know the serial number now.

  I followed the instructions and have produced a bootable USB and I checked this on a work dell computer where there is an option for me to boot from my USB if I so wish, but on my HP ENVY any options choose it does not appear with my USB in question and when I try to change the boot sequence making sure the usb/floppy and drive hard usb is above the rest of the sequencers starting it always starts just to the top as usual to my windows boot 10. I've disabled secure boot and used the boot of the legacy and it still does not work.

  I went through all the options I can that seem to be logic and it just does not work. I don't understand and I have to start using a usb key that I use the operating system can be very dangerous in a real environment, so it can not be downloaded to the hard drive.

  I need immediate help, this becomes quite frustrating now that it should be simple to do, but HP is not the way to simplisitic to do.

  Please if someone could point me in the right direction I would be so appreciative ideally if I could have a ride on the way to do

  I need this to work because I can't afford to buy new systems and its for my studies so its imperative

  Your PC has a motherboard of Memphis and happens to have a UEFI BIOS and the hard drive of the GPT format.

  You can check the type of hard disk online order volume by using the DiskPart utility.

  

  Create a flashdrive bootable UEFI with RUFUS.

  https://Rufus.AKEO.IE/

  Plug it into an available usb port before you press the power button. Near the powr button and immediately start to tap the F9 key to enter the boot from the sources menu. Select the Flash drive under the UEFI Boot sources. Let the boot process. If you have created the key correctly, it should start.

• Satellite A100-991 - cannot boot from USB device

  My Satellite A100-991 (MS Windows XP MCE, SP3) does not start from a USB key or USB hard drive. The same USB devices are bootable if they are connected to a desktop computer or a laptop from other manufacturers. I put the USB as the first boot device and use an image "Bart PE" on my USB device.

  In fact, I have installed 2.10 Phoenix Bios version and I wonder if I could update the BIOS by using the 'sa105v21.exe' program and that this would resolve the startup problem.

  Hello

  Have you tested different USB keys? I think that your current USB key is not compatible
  Also test the USB to different USB ports. A port may be defective for the computer to start t with him.

  Theoretically, you can try upgrading the BIOS but don t forget s a bit more risky and it should be the last step.
  Prior to this, load default settings in the BIOS and check if you can boot from USB.

• C50-A634 satellite will not boot from USB or DVD

  My new toshiba Satellite C50-A634 won't boot from usb or dvd,.
  I downloaded victory 8.1 and burn the image to a dvd but I always get an error message "no boot... device please restart."

  Can you please help?

  Hello

  Startup mode of the change in the BIOS settings and you should be able to use the optical drive as first boot device - http://aps2.toshiba-tro.de/kb0/TSB2C03F80002R01.htm

• Re: Satellite C650 - disable boot from USB

  Can you help me please? How can I disable boot from USB?

  Hi bailonijunior,

  As far as I know it of not possible to disable certain devices to boot.

  You can change the boot order in the BIOS. For example, you can set the HARD drive as first boot device. That means that the computer will always start HARD drive even a bootable USB device is connected.

  Check this box!

• Satellite M40-185 - how to boot from USB?

  I have a Toshiba Satellite M40-185

  I could not a off of usb because the two Mafany usb boot option

  Options for the device
  1. HARD DRIVE
  2 CD-DVD
  3 FDD
  4 LAN

  How to boot from usb?

  Hi esc.

  I think that you have answered the question yourself because you've posted all the startup options that are available and there is no option to boot USB on this laptop.

  All you can do is to install the latest BIOS, but as far as I know Satellite M40 can t boot from USB!

• Elitbook revolution 810 G2: unable to boot from USB Elitbook turn 810 G2

  Hello

  Initially, I bought 810 rotate with 8.1 Pro window.

  I've recently upgraded to 64-bit Pro 10 Windows.

  The problem is that I can not boot from USB. Computer recognizes the USB drive but when I click F9 and enter in bootmode... He acknowledges as "drive hard usb ' but when I select it... it has no effect and does not start.

  Could someone help me solve the problem? I need to be able to boot from USB drive...

  Thank you

  Windows 10 64-bit with UEFI can only boot from a GPT partition. It may be that your boot USB drive is partitioned as MBR [Master Boot Record] and should be partitioned GPT [Table of Partition GUID] for UEFI.

  Create bootable USB key with UEFI support

  If you found my answer helpful please say thank you by clicking on the icon of the thumb.
  If my answer has solved your problem, please mark it as accepted Solution. Thank you!