Boot safe mode problem

Similar Questions

• Horizontal lines in all modes (boot, safe mode etc.)

  Horizontal lines across my screen all... This occurs during startup, in POST, on the login screen in SafeMode etc etc...

  Example 1:

  

  the PC will sometimes hang after POST, before starting Windows and occasionally asking me if I'd like to try to get it back, that does not solve the problem. If she manages to get to the standard login screen, after typing my password, the PC will crash.

  I am able to boot in safe mode, but the lines are still there.

  Example 2:

  

  This obviously isn't a problem of graphics driver that the problem persists in safe mode and when starting. I also tried on 2 different monitors, who work very well when hooked to other devices.

  If someone could give me a solution or an idea where the problem may lie... I would be eternally grateful.

  My PC is as follows:

  Windows 7 Home Premium 64-bit

  ASUS Sabertooth 990FX Motherboard R2.0

  8-Core processor, 4.3 GHz AMD FX 8350

  16 GB (4 x 4 GB) Corsair XMS3 DDR3 1333 MHz RAM Performance

  ASUS GeForce GTX 760 2 GB 1033 MHz GPU

  512 GB SSD

  2 TB HARD drive

  power supply 750W

  Case Antec, with lots of cooling (5 fans)

  More photos HERE

  Hello

  These lines indicate corruption graphics driver or lack of graphic material.

  Monitor > cable > Port > which is connected to an integrated graphics card to a location on the motherboard or graphic material that is part of the motherboard.

  Glance of replacement or Exchange the graphic above.

  See you soon.

• XP won't start, or go into safe mode. problem w / file system.

  I have XP SP3, and while I was using it today, just to stop randomly and attempted to restart. I had made no changes to any system files or installed anything, etc...

  When he tried to restart, it froze to the logo screen and would not make progress, regardless of how much time was left for her. I tried to start in safe mode, and the usual list of system files and drivers ran to the bottom of the screen, stopping at Mup.sys it froze it there several times. I tried to start the Windows Recovery Console, nothing helps. I could not find my xp cd to try to fix him.

  I replaced my HARD drive died with a new one and now have XP SP3 on a single partition and Ubuntu on the other. I'll also do my data retrieved by Seagate. This problem is now resolved.

• Determine the connectivity of network in safe mode problem

  In Windows 7, I am connected to my wireless but no internet network. When I start it in safe mode with network problem is resolved. The best way to understand what is causing the connectivity in normal startup problem?

  Thus, a service blocking your internet connection, in this case. It is usually a firewall. Check your internet security and your Windows Firewall settings. If this does not work, you will need to go through the process of elimination to find which blocks the internet:

  1. Click Start
  2. in the search bar, type "msconfig".
  3. in the general tab: move the bubble in 'selective startup '.
  4. "load system services" and "Load Startup items" must be verified at the moment
  5. switch to the services tab
  6. Click on the box at the bottom for "hide all microsoft services".
  7. Uncheck all options
  8. Restart
  9. see if the internet works
  10. If this is not the case, go back to the services tab and begin to get rid of microsoft services, until you find what blocks your internet connection

• Is or is not "Application and Driver Recovery DVD" bootable? -Corrupted boot safe mode fail CryptUI.dll

  I'm recovering Pavilion dm4-3170se of my daughter. My daughter did not a recovery disk and has no recent backup of its set of data files.

  Problems (and what I've done so far) are quite parallels to what the user indicated in this post incredibly detailed:

  Difference is in start-up Mode (command line or not) safe, Windows startup fails on a dll, specifically CryptUI.DLL.

  Although incredibly detailed post user is not getting into the Windows startup, I have mod... for about 30 dll before it chokes on the corrupt. I tried a number of other things to get passed without result.

  Game drive recovery of origin of my daughter bought the farm when his house burned down. So I ordered and received a replacement of HP. I am reluctant to use before retrieving his data files because it may lose 40% of its professional activity.

  The set of recovery disks delivered includes an "Application and Driver Recovery DVD". Account of > 20 years Wintel machine tradition, I presume it is bootable. Surprisingly, user detailed Post got hers to start from the DVD drive. But the configuration of the BIOS to get the DVD drive as the first choice of startup is not to begin after two trials.

  Before I pour more time into that, I want to the Collective Wisdom here.

  Q1: Is this disc HP, numbered 691822-B22, meant to be bootable?

  Q2A: If it is, imagine you I can use the command line interface to copy the DLL identified-as-bad to the HD?

  Q2B: If she isn't, why the, uh, gollygoshdarn isn't? Must be a reasonable thing...

  Thanks for all the ideas based on experience.

  Hello:

  No matter what DVD driver and HP application I have ever used is not bootable.

  It should autorun from the windows desktop once windows has been reinstalled.

  This is the only question that I can answer those you requested.

  Suggestion...

  Make your own installation of W7 ISO from the link below.

  Use to install W7 and do not delete all partitions or format the drive.

  Windows install and create a folder Windows.old to the current operating system.

  Then, you can copy all the files you need from the Windows.old folder after installing W7.

  Once you are sure that you have got what you need, use the recovery disk set to restore the hard drive on his out of the box state.

  Link to files ISO of W7 is below.  Use the W7 x 64 home premium from the SP1 media list file refresh.

  http://forums.mydigitallife.info/threads/14709-Windows-7-Digital-River-direct-links-multiple-languages-x86-amp-x64/page59?p=470600&viewfull=1#post470600

  Then use this tool to transfer the iso file on a flash USB DVD or 4 GB drive.  The tool also performs the file iso bootable.

  http://www.microsoftstore.com/store/msusa/HTML/pbPage.Help_Win7_usbdvd_dwnTool

• Cannot boot safe mode.

  Hello

  I am running Windows 7 Service Pack 1 with Suse Linux 12.2, using dual-boot.

  For some reason, I can't start mode - pressing F8 leads to a normal start with no error message.

  By pressing F12 when the Dell icon correctly, throw myself into the boot options.

  I wonder if my problem with F8 is due to dual boot or the fact that my drive is partitioned.

  Thanks in advance,

  s660117

  The Dell logo is too early.  You get a GRUB prompt to select the operating system to start?  AFTER THAT is when you start, but once you see the Windows logo, it's too late.

• Z book 15: how affect legacy BIOS boot safe mode and disable.

  How to change the new white BIOS to the old legacy? The new has the secure boot disabled in my case setting. In the tutorial from hp, he shows how to turn off startup secured using the old bios.

  dannychris37 wrote:
  

  How to change the new white BIOS to the old legacy? The new has the secure boot disabled in my case setting. In the tutorial from hp, he shows how to turn off startup secured using the old bios.

  Have you tried this.

  Start Mode UEFI or Legacy BIOS mode

• How to disable boot safe MODE permanently in the 43.0b6 version?

  I tried all the suggestions I can find online without success.
  I'm not a developer but I have some experience with programming, for example VBA, fortran, algol, etc., and I've used windows since 1981.
  However, I would really appreciate step by step clear instructions in English.

  I did a refresh using the link you provided (thanks a lot for this) and reinstalled a couple of my most used extensions. Everything seems to work as I wanted to work. I still have to allow some others and I clean probably a few that are just hanging out but which should be no problem.
  Thanks for the quick and easy solution to the problem.

• Cannot boot safe mode or any mode - hangs on the mup.sys driver

  Can someone help me. I did some research on the internet and see that it is a familiar problem. I have been using a usb and someone removed without doing safely - storage key my laptop then froze and the only thing I could do was turn it off at the power button.

  Now I can't do anything - it just goes to several times on the same page saying that there was a problem to choose a way to start - I chose alone and nothing - it loads until the mup.sys driver and then just goes to the same page again. I'm out of ideas.

  Can anyone help?
  I'm trying to avoid the recovery disk that I really want to lose my job yet, but realize that might have to happen, you mind I read reports that it even still hangs when you try this option.

  Thanks Rachel

  Hello

  AFAIK the mup.sys is placed in the folder C:\Windows\System32\drivers and it s responsible for the control and the start-up of the operation of the system at the lower level (control of the printer or the graphics card, etc.).

  If your computer loads all the way up to mup.sys then your HARD drive should work. If he died it would not even charge anything at all. It would not even try to load this file.
  It is likely that this file is corrupted just.

  If you re not able to run the Win operating system and use the System Restore tool, so I put t see any other possibility to use the Toshiba Recovery CD.
  To save important files, you can remove the laptop HARD drive and connect the HARD drive to another computer via the USB interface.

• Update 40.0.2 is slow, hangs a lot, even in safe mode.

  So, I tried several things in the troubleshooting here in support articles, but none solved my problems.

  Basically, after that automatically put Firefox updated to 40.0.2, the browser crashes a lot on the opening and closing of tabs, loading Web sites as well. When idle, the CPU/RAM usage is normal, but opening or closing of tabs uses a lot of CPU (most of the time, 100% of the CPU is used in navigation) and it crashes every time. Scroll to the bottom of pages also allows the browser to hang. I tried to deactivate several plugins and extensions and I even tried to use the safe mode, but even in safe mode, it happens constantly. I'll post the specs of my computer (no), but don't forget that those issues didn't happen before the update.

  Core 2 Duo 2.93 GHz
  4 GB OF RAM
  Windows 7 Ultimate 32 bit
  GeForce 8400GS

  Please, what is anyone has found problems with this new update? What should I do? I use Firefox since 2007 and I love it, I wouldn't move to another.

  Create a new profile as a test to see if your profile is the source of the problem.

  See "create a profile":

  • https://support.Mozilla.org/KB/Profile-Manager-create-and-remove-Firefox-profiles
  • http://KB.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues

  If the new profile works then you can transfer files from a profile already used in the new profile, but be careful not to copy files corrupted to avoid transporting more problems.

  • http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

  Start the computer in safe mode Windows with network support (on the startup screen, press F8) to see if it has an impact.

  • http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/
  • http://www.7tutorials.com/4-ways-boot-safe-mode-Windows-10

• Mac mini will not start in safe mode

  Restarts, while now the SHIFT key at startup in safe mode, nothing happens, then I get a screen with lines of code, "panic (cpu 0 0xffffff800ebd255a appellant)", "" panic debugger called: < > "." In addition many other code, then it goes into a loop where he tries constantly to restart with the same results.

  I had problem with this for awhile, but have always been able to boot in safe mode and then restart and my system has always started.

  loss and out of business now.

  -Can you post a screenshot of readable of the kernel panic that appears on the screen? Who will provide the necessary information to help you.

  -What model Mac Mini? Some models have hardware problems

  Without that:

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  https://support.Apple.com/en-us/HT201295

  Subject of memory NVRAM and PRAM

  https://support.Apple.com/en-us/HT204063

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  https://support.Apple.com/en-us/HT201262

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  https://support.Apple.com/en-us/HT201314

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204904

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• XP SP3 update causes computer to only start in safe mode

  My daughter had XP IE8 running on his computer, site update Windows XP SP3 download.  I downloaded and installed, however it won't start in safe mode. When I remove SP3, the computer loads normally.  I then uninstalled IE8 (went back to IE6), made sure I had the pre-requistes, followed the steps as outline on the microsoft site, downloaded SP3 again and installed.  It will only re-start in safe mode.  I tried everything, no matter what I do, XP SP3 causes the computer to restart in safe mode only. I'm totally frustrated. Can someone help me?

  What is the origin of XP SP3 only start in SafeMode anfter installation? What can I do to fix this?

  Continuous restarts or can only to Safe Mode boot after installing WinXP SP3?

  See: http://msinfluentials.com/blogs/jesper/archive/2008/05/08/does-your-amd-based-computer-boot-after-installing-xp-sp3.aspx

  [NB: the above has been updated several times and now includes "a small tool that allows to detect the problem IntelPPM and mitigate before installing (WinXP SP3)".]

  Possible workaround: boot safe mode and rename INTELPMM. SYS to INTELPMM. OLD.

  Other references include:

  • Error after you upgrade a computer that uses one processor other than a processor of Intel for Windows XP Service Pack 2 or Service Pack 3 for Windows XP: "STOP: 0x0000007E"
    http://support.Microsoft.com/kb/953356
  • HP and Compaq Desktop PC: restart the computer after the display of the Stop error 0x0000007E after installing WinXP SP3]
    http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=en&cc=us&DocName=c01457284

• 110 - 000z: Safe Mode

  How to get into "safe" mode I got only once and I forgot how to do it again. Is easy to get out.

  If you are able to start OK, then it is easy, but if the reason why you ask is because of problems, then READ THIS GUIDE. http://www.7tutorials.com/5-ways-boot-safe-mode-Windows-8-Windows-81

• Blocked Windows in safe mode activation loop.

  So here's the problem, I used windows xp pro x 64 now for a little over 2 years and it has worked perfectly until today. I play with some programs of hertz of mouse that required me to start in safe mode. I went to boot safe mode via msconfig. My computer starts up fine until I got to the login screen and it said "this copy of Windows must be activated with Microsoft before you can continue. You cannot connect until you activate Windows. Because activation is not possible in safe mode, restart your computer in normal mode to activate windows. »

  Since I started with safe mode via msconfig, I can't boot into normal windows more. It will automatically start in safe mode and with this activation pop up, I can't get into the operating system, or even to command promt. I tried to start with the last known good configuration, I tried to start Windows normally through the f8 during the startup option.

  I really don't want to reformat, it will result in a large number of documents and deletion of files.

  Is there anyway I can somehow I cannot go into msconfig change back and start windows normally?

  Niramaya,
  Well, it sounds as if your system is not seeing the drive or is unable to access it properly.  At this point, you would probably need to see if the encryption program society has any means to help remove encryption, if you add the drive to another system.  With regard to obtaining a XP disc you need to contact the PC manufacturer and see if they offer a replacement recovery media. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• keyboard and mouse on packard bell laptop only work in safe mode

  I have a packard bell easynote laptop running on windows vista, which has fine worked for two years, the other day I went to signon and not all the hits of keyboard have been recognized, after possibly connection and found loading keyboard and a mouse does not respond as completely unusable.

  -Booted safe mode and everything works fine, ran the antivirus and diagnosis-nothing found, still only works in safe mode.

  has run a restore of system-nada, still only works in safe mode

  tried an own help start-up-no, still only works in safe mode

  Please help he kills me!

  Well, I decided to bite the bullet and give it a go, after all, I know very little of these things, however I'd wait until Saturday, when I have the time to focus on it, then the word 'Register' in your response reminded me that I had bought registry cleaner Uniblue several months ago that I ran last night and hey presto problem solved! :), I'll never know if your solution would work but thanks for your help anyway and I hope that you would have had me there.

  Rich